Showing 1–31 of 31 results for author: van Beuzekom, M

Resonant enhanced detection of the higher-order modes of a locked cavity

Authors: Ricardo Cabrita, Aaron Goodwin-Jones, Joris van Heijningen, Pavel Demin, Martin van Beuzekom, Matteo Tacca, Giacomo Bruno, Clément Lauzin

Abstract: Current gravitational-wave (GW) detectors are limited in the amount of circulating power they can reach. Optical absorption in the test masses leads to thermal effects that shift the eigenmodes of the optical cavities, and cause control issues such as parametric instabilities. Here we experimentally validate a novel technique using optical injection to measure the mode amplitudes within an optic… ▽ More Current gravitational-wave (GW) detectors are limited in the amount of circulating power they can reach. Optical absorption in the test masses leads to thermal effects that shift the eigenmodes of the optical cavities, and cause control issues such as parametric instabilities. Here we experimentally validate a novel technique using optical injection to measure the mode amplitudes within an optical resonator. We use a phase camera, similar to the ones installed at gravitational-wave detectors, in transmission of the cavity, to confirm the mode basis and image modes up to order 10. We showcase as well the capability of the phase camera to determine the optical phase between the carrier fundamental mode and other co-resonating higher-order modes, which can be used for optical suppression of parametric instabilities and automatic mode matching. These results highlight the relevance of implementing a similar scheme in current GW detectors to monitor thermal effects. △ Less

Submitted 6 May, 2025; originally announced May 2025.

Comments: 12 pages, 4 figures, 1 table. supplement with 6 pages, 2 figures

Embedding the Timepix4 in Micro-Pattern Gaseous Detectors

Authors: L. Scharenberg, J. Alozy, W. Billereau, F. Brunbauer, M. Campbell, P. Carbonez, K. J. Flöthner, F. Garcia, A. Garcia-Tejedor, T. Genetay, K. Heijhoff, D. Janssens, S. Kaufmann, M. Lisowska, X. Llopart, M. Mager, B. Mehl, H. Muller, R. de Oliveira, E. Oliveri, G. Orlandini, D. Pfeiffer, F. Piernas Diaz, A. Rodrigues, L. Ropelewski , et al. (5 additional authors not shown)

Abstract: The combination of Micro-Pattern Gaseous Detectors (MPGDs) and pixel charge readout enables specific experimental opportunities. Using the Timepix4 for the readout is advantageous because of its size (around 7 cm^2 active area) and its Through Silicon Vias. The latter enables to connect to the Timepix4 from the back side. Thus, it can be tiled on four sides, allowing it to cover large areas withou… ▽ More The combination of Micro-Pattern Gaseous Detectors (MPGDs) and pixel charge readout enables specific experimental opportunities. Using the Timepix4 for the readout is advantageous because of its size (around 7 cm^2 active area) and its Through Silicon Vias. The latter enables to connect to the Timepix4 from the back side. Thus, it can be tiled on four sides, allowing it to cover large areas without loss of active area. Here, the first results of reading out MPGDs with the Timepix4 are presented. Measurements with a Gas Electron Multiplier (GEM) detector show that event selection based on geometrical parameters of the interaction is possible, X-ray imaging studies can be performed, as well as energy and time-resolved measurements. In parallel, the embedding of a Timepix4 into a micro-resistive Well (uRWell) amplification structure is explored. The first mechanical tests have been successful. The status of the electrical functionality is presented, as well as simulation studies on the signal induction in such a device. △ Less

Submitted 16 March, 2025; originally announced March 2025.

Towards MPGDs with embedded pixel ASICs

Authors: L. Scharenberg, J. Alozy, W. Billereau, F. Brunbauer, M. Campbell, P. Carbonez, K. J. Flöthner, F. Garcia, A. Garcia-Tejedor, T. Genetay, K. Heijhoff, D. Janssens, S. Kaufmann, M. Lisowska, X. Llopart, M. Mager, B. Mehl, H. Muller, R. de Oliveira, E. Oliveri, G. Orlandini, D. Pfeiffer, F. Piernas Diaz, A. Rodrigues, L. Ropelewski , et al. (5 additional authors not shown)

Abstract: Combining gaseous detectors with a high-granularity pixelated charge readout enables experimental applications which otherwise could not be achieved. This includes high-resolution tracking of low-energetic particles, requiring ultra-low material budget, X-ray polarimetry at low energies ($\lessapprox$ 2 keV) or rare-event searches which profit from event selection based on geometrical parameters.… ▽ More Combining gaseous detectors with a high-granularity pixelated charge readout enables experimental applications which otherwise could not be achieved. This includes high-resolution tracking of low-energetic particles, requiring ultra-low material budget, X-ray polarimetry at low energies ($\lessapprox$ 2 keV) or rare-event searches which profit from event selection based on geometrical parameters. In this article, the idea of embedding a pixel ASIC - specifically the Timepix4 - into a micro-pattern gaseous amplification stage is illustrated. Furthermore, the first results of reading out a triple-GEM detector with the Timepix4 (GEMPix4) are shown, including the first X-ray images taken with a Timepix4 utilising Through Silicon Vias (TSVs). Lastly, a new readout concept is presented, called the 'Silicon Readout Board', extending the use of pixel ASICs to read out gaseous detectors to a wider range of HEP applications. △ Less

Submitted 22 December, 2024; originally announced December 2024.

Timing resolution performance of Timepix4 bump-bonded assemblies

Authors: Riccardo Bolzonella, Jerome Alexandre Alozy, Rafael Ballabriga, Martin van Beuzekom, Nicolò Vladi Biesuz, Michael Campbell, Paolo Cardarelli, Viola Cavallini, Victor Coco, Angelo Cotta Ramusino, Massimiliano Fiorini, Vladimir Gromov, Marco Guarise, Xavier Llopart Cudie, Shinichi Okamura, Gabriele Romolini, Alessandro Saputi, Arseniy Vitkovskiy

Abstract: The timing performance of the Timepix4 application-specific integrated circuit (ASIC) bump-bonded to a $100\;μ\textrm{m}$ thick n-on-p silicon sensor is presented. A picosecond pulsed infrared laser was used to generate electron-hole pairs in the silicon bulk in a repeatable fashion, controlling the amount, position and time of the stimulated charge signal. The timing resolution for a single pixel… ▽ More The timing performance of the Timepix4 application-specific integrated circuit (ASIC) bump-bonded to a $100\;μ\textrm{m}$ thick n-on-p silicon sensor is presented. A picosecond pulsed infrared laser was used to generate electron-hole pairs in the silicon bulk in a repeatable fashion, controlling the amount, position and time of the stimulated charge signal. The timing resolution for a single pixel has been measured to $107\;\textrm{ps}$ r.m.s. for laser-stimulated signals in the silicon sensor bulk. Considering multi-pixel clusters, the measured timing resolution reached $33\;\textrm{ps}$ r.m.s. exploiting oversampling of the timing information over several pixels. △ Less

Submitted 9 July, 2024; v1 submitted 23 April, 2024; originally announced April 2024.

Comments: 24 pages, 31 figures, Prepared for submission to JINST

The LHCb VELO Upgrade Module Construction

Authors: K. Akiba, M. Alexander, C. Bertella, A. Biolchini, A. Bitadze, G. Bogdanova, S. Borghi, T. J. V. Bowcock, K. Bridges, M. Brock, A. T. Burke, J. Buytaert, W. Byczynski, J. Carroll, V. Coco, P. Collins, A. Davis, O. De Aguiar Francisco, K. De Bruyn, S. De Capua, K. De Roo, F. Doherty, L. Douglas, L. Dufour, R. Dumps , et al. (62 additional authors not shown)

Abstract: The LHCb detector has undergone a major upgrade for LHC Run 3. This Upgrade I detector facilitates operation at higher luminosity and utilises full-detector information at the LHC collision rate, critically including the use of vertex information. A new vertex locator system, the VELO Upgrade, has been constructed. The core element of the new VELO are the double-sided pixelated hybrid silicon dete… ▽ More The LHCb detector has undergone a major upgrade for LHC Run 3. This Upgrade I detector facilitates operation at higher luminosity and utilises full-detector information at the LHC collision rate, critically including the use of vertex information. A new vertex locator system, the VELO Upgrade, has been constructed. The core element of the new VELO are the double-sided pixelated hybrid silicon detector modules which operate in vacuum close to the LHC beam in a high radiation environment. The construction and quality assurance tests of these modules are described in this paper. The modules incorporate 200 \mum thick, n-on-p silicon sensors bump-bonded to 130 \nm technology ASICs. These are attached with high precision to a silicon microchannel substrate that uses evaporative CO$_2$ cooling. The ASICs are controlled and read out with flexible printed circuits that are glued to the substrate and wire-bonded to the chips. The mechanical support of the module is given by a carbon fibre plate, two carbon fibre rods and an aluminium plate. The sensor attachment was achieved with an average precision of 21 $\mathrm{μm}$, more than 99.5\% of all pixels are fully functional, and a thermal figure of merit of 3 \mathrm{Kcm^{2}W^{-1}}$ was achieved. The production of the modules was successfully completed in 2021, with the final assembly and installation completed in time for data taking in 2022. △ Less

Submitted 21 April, 2024; originally announced April 2024.

Report number: LHCb-DP-2024-001

Transverse Mode Control in Quantum Enhanced Interferometers: A Review and Recommendations for a New Generation

Authors: Aaron W. Goodwin-Jones, Ricardo Cabrita, Mikhail Korobko, Martin van Beuzekom, Daniel D. Brown, Viviana Fafone, Joris van Heijningen, Alessio Rocchi, Mitchell G. Schiworski, Matteo Tacca

Abstract: Adaptive optics has made significant advancement over the past decade, becoming the essential technology in a wide variety of applications, particularly in the realm of quantum optics. One key area of impact is gravitational-wave detection, where quantum correlations are distributed over kilometer-long distances by beams with hundreds of kilowatts of optical power. Decades of development were requ… ▽ More Adaptive optics has made significant advancement over the past decade, becoming the essential technology in a wide variety of applications, particularly in the realm of quantum optics. One key area of impact is gravitational-wave detection, where quantum correlations are distributed over kilometer-long distances by beams with hundreds of kilowatts of optical power. Decades of development were required to develop robust and stable techniques to sense mismatches between the Gaussian beams and the resonators, all while maintaining the quantum correlations. Here we summarize the crucial advancements in transverse mode control required for gravitational-wave detection. As we look towards the advanced designs of future detectors, we highlight key challenges and offer recommendations for the design of these instruments. We conclude the review with a discussion of the broader application of adaptive optics in quantum technologies: communication, computation, imaging and sensing. △ Less

Submitted 8 November, 2023; originally announced November 2023.

Report number: LIGO-P2300282, VIR-0769A-23

Radiation Tolerance of Low-Noise Photoreceivers for the LISA Space Mission

Authors: P. Colcombet, N. Dinu-Jaeger, C. Inguimbert, T. Nuns, S. Bruhier, N. Christensen, P. Hofverberg, N. van Bakel, M. van Beuzekom, T. Mistry, G. Visser, D. Pascucci, K. Izumi, K. Komori, G. Heinzel, G. Fernández Barranco, J. J. M. in t Zand, P. Laubert, M. Frericks

Abstract: This study investigates the effects of space environmental radiation on the performance of InGaAs Quadrant Photodiodes (QPDs) and assesses their suitability for the Laser Interferometer Space Antenna (LISA) mission. QPDs of 1.0, 1.5 and 2.0 mm have been irradiated with 20 and 60 MeV protons, 0.5 and 1 MeV electrons, and Co$^{60}$ gamma. An exposure corresponding to a displacement damage equivalent… ▽ More This study investigates the effects of space environmental radiation on the performance of InGaAs Quadrant Photodiodes (QPDs) and assesses their suitability for the Laser Interferometer Space Antenna (LISA) mission. QPDs of 1.0, 1.5 and 2.0 mm have been irradiated with 20 and 60 MeV protons, 0.5 and 1 MeV electrons, and Co$^{60}$ gamma. An exposure corresponding to a displacement damage equivalent fluence of $1.0 \times 10^{+12}$ p/cm$^2$ for 20 and 60 MeV protons and a total ionizing dose of 237 krad were applied, surpassing the anticipated radiation levels for the LISA mission by a factor of approximately five. Experiments were conducted to measure changes in QPD dark current, capacitance, and responsivity. The QPDs are integrated with a low-noise DC-coupled transimpedance amplifier to form the Photoreceiver (QPR). QPR noise and performance in an interferometric system like LISA were also measured. Although radiation impacted their dark current and responsivity, almost all QPDs met LISA's validation criteria and did not demonstrate any critical failure. These findings prove that the tested QPDs are promising candidates for LISA and other space-based missions. △ Less

Submitted 15 October, 2023; originally announced October 2023.

Comments: Proceedings of RADECS 2023 conference, https://radecs2023.com/

The LHCb upgrade I

Authors: LHCb collaboration, R. Aaij, A. S. W. Abdelmotteleb, C. Abellan Beteta, F. Abudinén, C. Achard, T. Ackernley, B. Adeva, M. Adinolfi, P. Adlarson, H. Afsharnia, C. Agapopoulou, C. A. Aidala, Z. Ajaltouni, S. Akar, K. Akiba, P. Albicocco, J. Albrecht, F. Alessio, M. Alexander, A. Alfonso Albero, Z. Aliouche, P. Alvarez Cartelle, R. Amalric, S. Amato , et al. (1298 additional authors not shown)

Abstract: The LHCb upgrade represents a major change of the experiment. The detectors have been almost completely renewed to allow running at an instantaneous luminosity five times larger than that of the previous running periods. Readout of all detectors into an all-software trigger is central to the new design, facilitating the reconstruction of events at the maximum LHC interaction rate, and their select… ▽ More The LHCb upgrade represents a major change of the experiment. The detectors have been almost completely renewed to allow running at an instantaneous luminosity five times larger than that of the previous running periods. Readout of all detectors into an all-software trigger is central to the new design, facilitating the reconstruction of events at the maximum LHC interaction rate, and their selection in real time. The experiment's tracking system has been completely upgraded with a new pixel vertex detector, a silicon tracker upstream of the dipole magnet and three scintillating fibre tracking stations downstream of the magnet. The whole photon detection system of the RICH detectors has been renewed and the readout electronics of the calorimeter and muon systems have been fully overhauled. The first stage of the all-software trigger is implemented on a GPU farm. The output of the trigger provides a combination of totally reconstructed physics objects, such as tracks and vertices, ready for final analysis, and of entire events which need further offline reprocessing. This scheme required a complete revision of the computing model and rewriting of the experiment's software. △ Less

Submitted 10 September, 2024; v1 submitted 17 May, 2023; originally announced May 2023.

Comments: All figures and tables, along with any supplementary material and additional information, are available at http://lhcbproject.web.cern.ch/lhcbproject/Publications/LHCbProjectPublic/LHCb-DP-2022-002.html (LHCb public pages)

Report number: LHCb-DP-2022-002

Journal ref: JINST 19 (2024) P05065

Reconstruction of charged tracks with Timepix4 ASICs

Authors: Kazu Akiba, Martin van Beuzekom, Vincent van Beveren, Wiktor Byczynski, Victor Coco, Paula Collins, Elena Dall'Occo, Raphael Dumps, Tim Evans, Robbert Geertsema, Evangelios Gkougkousis, Marius Halvorsen, Bas van der Heijden, Kevin Heijhoff, Edgar Lemos Cid, Tommaso Pajero, David Rolf, Heinrich Schindler

Abstract: The design of a detector system comprised of four silicon sensors bump-bonded to Timepix4 ASICs is described together with its data acquisition system, operational infrastructure, and dedicated software. The spatial and temporal performance of the system are assessed with a 180 GeV/c mixed hadron beam at the CERN SPS and reported in detail. Particle tracks are reconstructed using time-space measur… ▽ More The design of a detector system comprised of four silicon sensors bump-bonded to Timepix4 ASICs is described together with its data acquisition system, operational infrastructure, and dedicated software. The spatial and temporal performance of the system are assessed with a 180 GeV/c mixed hadron beam at the CERN SPS and reported in detail. Particle tracks are reconstructed using time-space measurements from the four detector planes. The spatial hit resolution is assessed to be $(15.5\pm 0.5)$ $μ$m and $(4.5\pm0.3)$ $μ$m for 100 and 300 $μ$m thick sensors, respectively. The timestamps from the detectors are also measured with fine precision, yielding time resolutions of $(452\pm10)$ ps, $(420\pm10)$ ps, $(639\pm10)$ ps, $(631\pm10)$ ps for the two 100 and two 300 $μ$m thick sensors respectively. These measurements are combined to a track time resolution of $(340\pm 5)$ ps. △ Less

Submitted 23 December, 2022; v1 submitted 4 October, 2022; originally announced October 2022.

Comments: 15 pages, 15 images in 9 figures

ETpathfinder: a cryogenic testbed for interferometric gravitational-wave detectors

Authors: A. Utina, A. Amato, J. Arends, C. Arina, M. de Baar, M. Baars, P. Baer, N. van Bakel, W. Beaumont, A. Bertolini, M. van Beuzekom, S. Biersteker, A. Binetti, H. J. M. ter Brake, G. Bruno, J. Bryant, H. J. Bulten, L. Busch, P. Cebeci, C. Collette, S. Cooper, R. Cornelissen, P. Cuijpers, M. van Dael, S. Danilishin , et al. (90 additional authors not shown)

Abstract: The third-generation of gravitational wave observatories, such as the Einstein Telescope (ET) and Cosmic Explorer (CE), aim for an improvement in sensitivity of at least a factor of ten over a wide frequency range compared to the current advanced detectors. In order to inform the design of the third-generation detectors and to develop and qualify their subsystems, dedicated test facilities are req… ▽ More The third-generation of gravitational wave observatories, such as the Einstein Telescope (ET) and Cosmic Explorer (CE), aim for an improvement in sensitivity of at least a factor of ten over a wide frequency range compared to the current advanced detectors. In order to inform the design of the third-generation detectors and to develop and qualify their subsystems, dedicated test facilities are required. ETpathfinder prototype uses full interferometer configurations and aims to provide a high sensitivity facility in a similar environment as ET. Along with the interferometry at 1550 nm and silicon test masses, ETpathfinder will focus on cryogenic technologies, lasers and optics at 2090 nm and advanced quantum-noise reduction schemes. This paper analyses the underpinning noise contributions and combines them into full noise budgets of the two initially targeted configurations: 1) operating with 1550 nm laser light and at a temperature of 18 K and 2) operating at 2090 nm wavelength and a temperature of 123 K. △ Less

Submitted 10 June, 2022; originally announced June 2022.

Timing performance of the Timepix4 front-end

Authors: K. Heijhoff, K. Akiba, R. Ballabriga, M. van Beuzekom, M. Campbell, A. P. Colijn, M. Fransen, R. Geertsema, V. Gromov, X. Llopart Cudie

Abstract: A characterisation of the Timepix4 pixel front-end with a strong focus on timing performance is presented. Externally generated test pulses were used to probe the per-pixel time-to-digital converter (TDC) and measure the time-bin sizes by precisely controlling the test-pulse arrival time in steps of 10 ps. The results indicate that the TDC can achieve a time resolution of 60 ps, provided that a ca… ▽ More A characterisation of the Timepix4 pixel front-end with a strong focus on timing performance is presented. Externally generated test pulses were used to probe the per-pixel time-to-digital converter (TDC) and measure the time-bin sizes by precisely controlling the test-pulse arrival time in steps of 10 ps. The results indicate that the TDC can achieve a time resolution of 60 ps, provided that a calibration is performed to compensate for frequency variation in the voltage controlled oscillators of the pixel TDCs. The internal clock distribution system of Timepix4 was used to control the arrival time of internally generated analog test pulses in steps of about 20 ps. The analog test pulse mechanism injects a controlled amount of charge directly into the analog front-end (AFE) of the pixel, and was used to measure the time resolution as a function of signal charge, independently of the TDC. It was shown that for the default configuration, the AFE time resolution in the hole-collecting mode is limited to 105 ps. However, this can be improved up to about 60 ps by increasing the preamplifier bias-current at the cost of increased power dissipation. For the electron-collecting mode, an AFE time resolution of 47 ps was measured for a bare Timepix4 device at a signal charge of 21 ke. It was observed that additional input capacitance from a bonded sensor reduces this figure to 62 ps. △ Less

Submitted 11 July, 2022; v1 submitted 29 March, 2022; originally announced March 2022.

Journal ref: 2022 JINST 17 P07006

Improving the stability of frequency dependent squeezing with bichromatic control of filter cavity length, alignment and incident beam pointing

Authors: Yuhang Zhao, Eleonora Capocasa, Marc Eisenmann, Naoki Aritomi, Michael Page, Yuefan Guo, Eleonora Polini, Koji Arai, Yoichi Aso, Martin van Beuzekom, Yao-Chin Huang, Ray-Kuang Lee, Harald Lück, Osamu Miyakawa, Pierre Prat, Ayaka Shoda, Matteo Tacca, Ryutaro Takahashi, Henning Vahlbruch, Marco Vardaro, Chien-Ming Wu, Matteo Leonardi, Matteo Barsuglia, Raffaele Flaminio

Abstract: Frequency dependent squeezing is the main upgrade for achieving broadband quantum noise reduction in upcoming observation runs of gravitational wave detectors. The proper frequency dependence of the squeezed quadrature is obtained by reflecting squeezed vacuum from a Fabry-Perot filter cavity detuned by half of its linewidth. However, since the squeezed vacuum contains no classical amplitude, co-p… ▽ More Frequency dependent squeezing is the main upgrade for achieving broadband quantum noise reduction in upcoming observation runs of gravitational wave detectors. The proper frequency dependence of the squeezed quadrature is obtained by reflecting squeezed vacuum from a Fabry-Perot filter cavity detuned by half of its linewidth. However, since the squeezed vacuum contains no classical amplitude, co-propagating auxiliary control beams are required to achieve the filter cavity's length, alignment, and incident beam pointing stability. In our frequency dependent squeezing experiment at the National Astronomical Observatory of Japan, we used a control beam at a harmonic of squeezed vacuum wavelength and found visible detuning variation related to the suspended mirrors angular drift. These variations can degrade interferometer quantum noise reduction. We investigated various mechanisms that can cause the filter cavity detuning variation. The detuning drift is found to be mitigated sufficiently by fixing the incident beam pointing and applying filter cavity automatic alignment. It was also found that there is an optimal position of the beam on the filter cavity mirror that helps to reduce the detuning fluctuations. Here we report a stabilized filter cavity detuning variation of less than 10$\,$Hz compared to the 113$\,$Hz cavity linewidth. Compared to previously published results [Phys. Rev. Lett. 124, 171101 (2020)], such detuning stability would be sufficient to make filter cavity detuning drift induced gravitational wave detector detection range fluctuation reduce from $11\%$ to within $2\%$. △ Less

Submitted 21 March, 2022; originally announced March 2022.

Comments: Accepted by PRD

Spatial resolution and efficiency of prototype sensors for the LHCb VELO Upgrade

Authors: E. Buchanan, K. Akiba, M. van Beuzekom, P. Collins, E. Dall'Occo, T. Evans, V. Franco Lima, R. Geertsema, P. Kopciewicz, E. Price, B. Rachwal, S. Richards, D. Saunders, H. Schindler, T. Szumlak, P. Tsopelas, J. Velthuis, M. R. J. Williams

Abstract: A comprehensive study of the spatial resolution and detection efficiency of sensor prototypes developed for the LHCb VELO upgrade is presented. Data samples were collected at the CERN SPS H8 beam line using a hadron mixture of protons and pions with momenta of approximately 180 GeV/c. The sensor performance was characterised using both irradiated and non-irradiated sensors. Irradiated samples were… ▽ More A comprehensive study of the spatial resolution and detection efficiency of sensor prototypes developed for the LHCb VELO upgrade is presented. Data samples were collected at the CERN SPS H8 beam line using a hadron mixture of protons and pions with momenta of approximately 180 GeV/c. The sensor performance was characterised using both irradiated and non-irradiated sensors. Irradiated samples were subjected to a maximum fluence of $\mathrm{8\times10^{15}~1~MeV~n_{eq}~cm^{-2}}$, of both protons and neutrons. The spatial resolution is measured comparing the detected hits to the position as predicted by tracks reconstructed by the Timepix3 telescope. The resolution is presented for different applied bias voltages and track angles, sensor thickness and implant size. △ Less

Submitted 28 March, 2022; v1 submitted 28 January, 2022; originally announced January 2022.

Comments: 18 pages, 15 Figures

Charge and temporal characterisation of silicon sensors using a two-photon absorption laser

Authors: R. Geertsema, K. Akiba, M. van Beuzekom, T. Bischoff, K. Heijhoff, H. Snoek

Abstract: First measurements are presented from a newly commissioned two-photon absorption (TPA) setup at Nikhef. The characterisation of the various components of the system is discussed. Two planar silicon sensors, one being electron collecting and one hole collecting, are characterised with detailed measurements of the charge collection and time resolution. The TPA spot is determined to have a radius of… ▽ More First measurements are presented from a newly commissioned two-photon absorption (TPA) setup at Nikhef. The characterisation of the various components of the system is discussed. Two planar silicon sensors, one being electron collecting and one hole collecting, are characterised with detailed measurements of the charge collection and time resolution. The TPA spot is determined to have a radius of 0.975(11) $μ\text{m}$ and length of 23.8 $μ\text{m}$ in silicon. The trigger time resolution of the system is shown to be maximally 30.4 ps. For both sensors, uniform charge collection is observed over the pixels, and the pixel side metallisation is imaged directly using the TPA technique. The best time resolution for a single pixel is found to be 600 ps and 560 ps for the electron and hole collecting sensors respectively, and is dominated by ASIC contributions. Further scans at different depths in the sensor and positions within the pixels have been performed and show a uniform response. It is concluded that the TPA setup is a powerful tool to investigate the charge collection and temporal properties of silicon sensors. △ Less

Submitted 24 January, 2022; v1 submitted 22 December, 2021; originally announced December 2021.

Timing measurements with a 3D silicon sensor on Timepix3 in a 180 GeV/c hadron beam

Authors: K. Heijhoff, K. Akiba, R. Bates, M. van Beuzekom, P. Bosch, A. P. Colijn, R. Geertsema, V. Gromov, M. L. E. Heidotting, L. S. Hendrikx, D. Hynds, H. Snoek

Abstract: Test beam measurements have been carried out with a 3D sensor on a Timepix3 ASIC and the time measurements are presented. The measurements are compared to those of a thin planar sensor on Timepix3. It is shown that for a perpendicularly incident beam the time resolution of both detectors is dominated by the Timepix3 front-end. The 3D detector is dominated by the time-to-digital conversion whereas… ▽ More Test beam measurements have been carried out with a 3D sensor on a Timepix3 ASIC and the time measurements are presented. The measurements are compared to those of a thin planar sensor on Timepix3. It is shown that for a perpendicularly incident beam the time resolution of both detectors is dominated by the Timepix3 front-end. The 3D detector is dominated by the time-to-digital conversion whereas the analog front-end jitter also gives a significant contribution for the thin planar detector. The 3D detector reaches an overall time resolution of 567(6)ps compared to 683(8)ps for the thin planar detector. For a grazing angle beam, however, the thin planar detector achieves a better time resolution because it has a lower pixel capacitance, and therefore suffers less from jitter in the analog front-end for the low charge signals that mainly occur in this type of measurement. Finally, it is also shown that the 3D and thin planar detector can achieve time resolutions for large clusters of about 100ps and 250ps, respectively, by combining many single hit measurements. △ Less

Submitted 25 May, 2021; originally announced May 2021.

Journal ref: 2021 JINST 16 P08009

Temporal characterisation of silicon sensors on Timepix3 ASICs

Authors: Elena Dall'Occo, Kazu Akiba, Martin van Beuzekom, Emma Buchanan, Paula Collins, Timothy Evans, Vinicius Franco Lima, Robbert Geertsema, Heinrich Schindler, Hella Snoek, Panagiotis Tsopelas

Abstract: The timing performance of silicon sensors bump-bonded to Timepix3 ASICs is investigated, prior to and after different types of irradiation up to $8 \times 10^{15} 1 \mathrm{\,Me\kern -0.1em V} \mathrm{ \,n_{eq}} {\mathrm{ \,cm}}^{-2}$. The sensors have been tested with a beam of charged particles in two different configurations, perpendicular to and almost parallel to the incident beam. The second… ▽ More The timing performance of silicon sensors bump-bonded to Timepix3 ASICs is investigated, prior to and after different types of irradiation up to $8 \times 10^{15} 1 \mathrm{\,Me\kern -0.1em V} \mathrm{ \,n_{eq}} {\mathrm{ \,cm}}^{-2}$. The sensors have been tested with a beam of charged particles in two different configurations, perpendicular to and almost parallel to the incident beam. The second approach, known as the grazing angles method, is shown to be a powerful method to investigate not only the charge collection, but also the time-to-threshold properties as a function of the depth at which the charges are liberated. △ Less

Submitted 6 August, 2021; v1 submitted 11 February, 2021; originally announced February 2021.

Journal ref: 2021 JINST 16 P07035

Charge collection properties of prototype sensors for the LHCb VELO upgrade

Authors: R. Geertsema, K. Akiba, M. van Beuzekom, E. Buchanan, C. Burr, W. Byczynski, P. Collins, E. Dall'Occo, T. Evans, V. Franco Lima, K. Heijhoff, P. Kopciewicz, F. Marinho, E. Price, B. Rachwal, S. Richards, D. Saunders, H. Schindler, H. Snoek, T. Szumlak, P. Tsopelas, J. Velthuis, M. R. J. Williams

Abstract: An extensive sensor testing campaign is presented, dedicated to measuring the charge collection properties of prototype candidates for the Vertex Locator (VELO) detector for the upgraded LHCb experiment. The charge collection is measured with sensors exposed to fluences of up to $8 \times 10^{15}~1~\mathrm{\,Me\kern -0.1em V}~ \mathrm{ \,n_{eq}}~{\mathrm{ \,cm}}^{-2}$, as well as with nonirradiate… ▽ More An extensive sensor testing campaign is presented, dedicated to measuring the charge collection properties of prototype candidates for the Vertex Locator (VELO) detector for the upgraded LHCb experiment. The charge collection is measured with sensors exposed to fluences of up to $8 \times 10^{15}~1~\mathrm{\,Me\kern -0.1em V}~ \mathrm{ \,n_{eq}}~{\mathrm{ \,cm}}^{-2}$, as well as with nonirradiated prototypes. The results are discussed, including the influence of different levels of irradiation and bias voltage on the charge collection properties. Charge multiplication is observed on some sensors that were nonuniformly irradiated with 24 GeV protons, to the highest fluence levels. An analysis of the charge collection near the guard ring region is also presented, revealing significant differences between the sensor prototypes. All tested sensor variants succeed in collecting the minimum required charge of 6000 electrons after the exposure to the maximum fluence. △ Less

Submitted 18 December, 2020; v1 submitted 20 October, 2020; originally announced October 2020.

Timing performance of the LHCb VELO Timepix3 Telescope

Authors: K. Heijhoff, K. Akiba, M. van Beuzekom, P. Bosch, J. Buytaert, M. Campbell, A. P. Colijn, P. Collins, E. Dall'Occo, T. Evans, R. Geertsema, M. L. E. Heidotting, D. Hynds, X. Llopart Cudie, H. Schindler, H. Snoek

Abstract: We performed a detailed study of the timing performance of the LHCb VELO Timepix3 Telescope with a 180 GeV/c mixed hadron beam at the CERN SPS. A twofold method was developed to improve the resolution of single-plane time measurements, resulting in a more precise overall track time measurement. The first step uses spatial information of reconstructed tracks in combination with the measured signal… ▽ More We performed a detailed study of the timing performance of the LHCb VELO Timepix3 Telescope with a 180 GeV/c mixed hadron beam at the CERN SPS. A twofold method was developed to improve the resolution of single-plane time measurements, resulting in a more precise overall track time measurement. The first step uses spatial information of reconstructed tracks in combination with the measured signal charge in the sensor to correct for a mixture of different effects: variations in charge carrier drift time; variations in signal induction, which are the result of a non-uniform weighting field in the pixels; and lastly, timewalk in the analog front-end. The second step corrects for systematic timing offsets in Timepix3 that vary from -2 ns to 2 ns. By applying this method, we improved the track time resolution from 438$\,\pm\,$16 ps to 276$\,\pm\,$4 ps. △ Less

Submitted 11 August, 2020; originally announced August 2020.

The Upgrade I of LHCb VELO -- towards an intelligent monitoring platform

Authors: P. Kopciewicz, T. Szumlak, M. Majewski, K. Akiba, O. Augusto, J. Back, D. S. Bobulska, G. Bogdanova, S. Borghi, T. Bowcock, J. Buytaert, E. Lemos Cid, V. Coco, P. Collins, E. Dall'Occo, K. de Bruyn, S. de Capua, F. Dettori, K. Dreimanis, D. Dutta, L. Eklund, T. Evans, M. Ferro-Luzzi W. Funk, L. Meyer Garcia, O. Boente García , et al. (41 additional authors not shown)

Abstract: The Large Hadron Collider beauty (LHCb) detector is designed to detect decays of b- and c- hadrons for the study of CP violation and rare decays. At the end of the LHC Run 2, many of the LHCb measurements remained statistically dominated. In order to increase the trigger yield for purely hadronic channels, the hardware trigger will be removed, and the detector will be read out at 40 MHz. This, in… ▽ More The Large Hadron Collider beauty (LHCb) detector is designed to detect decays of b- and c- hadrons for the study of CP violation and rare decays. At the end of the LHC Run 2, many of the LHCb measurements remained statistically dominated. In order to increase the trigger yield for purely hadronic channels, the hardware trigger will be removed, and the detector will be read out at 40 MHz. This, in combination with the five-fold increase in luminosity, requires radical changes to LHCb's electronics, and, in some cases, the replacement of entire sub-detectors with state-of-the-art detector technologies. The Vertex Locator (VELO) surrounding the interaction region is used to reconstruct the collision points (primary vertices) and decay vertices of long-lived particles (secondary vertices). The upgraded VELO will be composed of 52 modules placed along the beam axis divided into two retractable halves. The modules will each be equipped with 4 silicon hybrid pixel tiles, each read out by 3 VeloPix ASICs. The total output data rate anticipated for the whole detector will be around 1.6 Tbit/s. The highest occupancy ASICs will have pixel hit rates of approximately 900 Mhit/s, with the corresponding output data rate of 15 Gbit/s. The LHCb upgrade detector will be the first detector to read out at the full LHC rate of 40 MHz. The VELO upgrade will utilize the latest detector technologies to read out at this rate while maintaining the required radiation-hard profile and minimizing the detector material. △ Less

Submitted 22 July, 2022; v1 submitted 16 June, 2020; originally announced June 2020.

Journal ref: Journal of Instrumentation (JINST), Volume 15, June 2020

LHCb VELO Timepix3 Telescope

Authors: Kazu Akiba, Martin van Beuzekom, Henk Boterenbrood, Emma Buchanan, Jan Buytaert, Wiktor Byczynski, Xabier Cid Vidal, Paula Collins, Elena Dall'Occo, Alvaro Dosil Suarez, Raphael Dumps, Tim Evans, Vinicius Franco Lima, Abraham Gallas Torreira, Julian Garcia Pardinas, Bas van der Heijden, Christoph Hombach, Malcolm John, Szymon Kulis, Xavi Llopart Cudie, Franciole Marinho, Eugenia Price, Sophie Richards, Pablo Rodriguez Perez, Daniel Saunders , et al. (8 additional authors not shown)

Abstract: The LHCb VELO Timepix3 telescope is a silicon pixel tracking system constructed initially to evaluate the performance of LHCb VELO Upgrade prototypes. The telesope consists of eight hybrid pixel silicon sensor planes equipped with the Timepix3 ASIC. The planes provide excellent charge measurement, timestamping and spatial resolution and the system can function at high track rates. This paper descr… ▽ More The LHCb VELO Timepix3 telescope is a silicon pixel tracking system constructed initially to evaluate the performance of LHCb VELO Upgrade prototypes. The telesope consists of eight hybrid pixel silicon sensor planes equipped with the Timepix3 ASIC. The planes provide excellent charge measurement, timestamping and spatial resolution and the system can function at high track rates. This paper describes the construction of the telescope and its data acquisition system and offline reconstruction software. A timing resolution of 350~ps was obtained for reconstructed tracks. A pointing resolution of better than 2~\mum was determined for the 180~GeV/c %\gevc mixed hadron beam at the CERN SPS. The telescope has been shown to operate at a rate of 5 million particles~\unit{s^{-1}\cdot cm^{-2}} without a loss in efficiency. △ Less

Submitted 26 February, 2019; originally announced February 2019.

Identification of particles with Lorentz factor up to $10^{4}$ with Transition Radiation Detectors based on micro-strip silicon detectors

Authors: J. Alozy, N. Belyaev, M. Campbell, M. Cherry, F. Dachs, S. Doronin, K. Filippov, P. Fusco, F. Gargano, E. Heijne, S. Konovalov, D. Krasnopevtsev, X. Llopart, F. Loparco, V. Mascagna, M. N. Mazziotta, H. Pernegger, D. Ponomarenko, M. Prest, D. Pyatiizbyantseva, R. Radomskii, C. Rembser, A. Romaniouk, A. A. Savchenko, D. Schaefer , et al. (17 additional authors not shown)

Abstract: This work is dedicated to the study of a technique for hadron identification in the TeV momentum range, based on the simultaneous measurement of the energies and of the emission angles of the Transition Radiation (TR) X-rays with respect to the radiating particles. A detector setup has been built and tested with particles in a wide range of Lorentz factors (from about $10^3$ to about… ▽ More This work is dedicated to the study of a technique for hadron identification in the TeV momentum range, based on the simultaneous measurement of the energies and of the emission angles of the Transition Radiation (TR) X-rays with respect to the radiating particles. A detector setup has been built and tested with particles in a wide range of Lorentz factors (from about $10^3$ to about $4 \times 10^4$ crossing different types of radiators. The measured double-differential (in energy and angle) spectra of the TR photons are in a reasonably good agreement with TR simulation predictions. △ Less

Submitted 22 February, 2019; v1 submitted 31 January, 2019; originally announced January 2019.

Comments: 31 pages, 12 figures, paper published on Nuclear Instruments & Methods A

Journal ref: Nuclear Instruments & Methods A, volume 927 (2019), pages 1-13

Mapping the material in the LHCb vertex locator using secondary hadronic interactions

Authors: M. Alexander, W. Barter, A. Bay, L. J. Bel, M. van Beuzekom, G. Bogdanova, S. Borghi, T. J. V. Bowcock, E. Buchanan, J. Buytaert, K. Carvalho Akiba, S. Chen, V. Coco, P. Collins, A. Crocombe, F. Da Cunha Marinho, E. Dall'Occo, S. De Capua, C. T. Dean, F. Dettori, D. Dossett, K. Dreimanis, G. Dujany, L. Eklund, T. Evans , et al. (41 additional authors not shown)

Abstract: Precise knowledge of the location of the material in the LHCb vertex locator (VELO) is essential to reducing background in searches for long-lived exotic particles, and in identifying jets that originate from beauty and charm quarks. Secondary interactions of hadrons produced in beam-gas collisions are used to map the location of material in the VELO. Using this material map, along with properties… ▽ More Precise knowledge of the location of the material in the LHCb vertex locator (VELO) is essential to reducing background in searches for long-lived exotic particles, and in identifying jets that originate from beauty and charm quarks. Secondary interactions of hadrons produced in beam-gas collisions are used to map the location of material in the VELO. Using this material map, along with properties of a reconstructed secondary vertex and its constituent tracks, a $p$-value can be assigned to the hypothesis that the secondary vertex originates from a material interaction. A validation of this procedure is presented using photon conversions to dimuons. △ Less

Submitted 18 June, 2018; v1 submitted 20 March, 2018; originally announced March 2018.

Comments: All figures and tables are available at https://lhcbproject.web.cern.ch/lhcbproject/Publications/LHCbProjectPublic/LHCb-DP-2018-002.html

Report number: CERN-LHCb-DP-2018-002

Journal ref: JINST 13, P06008 (2018)

Coincidence velocity map imaging using Tpx3Cam, a time stamping optical camera with 1.5 ns timing resolution

Authors: Arthur Zhao, Martin van Beuzekom, Bram Bouwens, Dmitry Byelov, Irakli Chakaberia, Chuan Cheng, Erik Maddox, Andrei Nomerotski, Peter Svihra, Jan Visser, Vaclav Vrba, Thomas Weinacht

Abstract: We demonstrate a coincidence velocity map imaging apparatus equipped with a novel time stamping fast optical camera, Tpx3Cam, whose high sensitivity and ns timing resolution allow for simultaneous position and time-of-flight detection. This single detector design is simple, flexible and capable of highly differential measurements. We show detailed characterization of the camera and its application… ▽ More We demonstrate a coincidence velocity map imaging apparatus equipped with a novel time stamping fast optical camera, Tpx3Cam, whose high sensitivity and ns timing resolution allow for simultaneous position and time-of-flight detection. This single detector design is simple, flexible and capable of highly differential measurements. We show detailed characterization of the camera and its application in strong field ionization experiments. △ Less

Submitted 13 October, 2017; v1 submitted 19 July, 2017; originally announced July 2017.

Comments: 18 pages, 12 figures

Proton radiography to improve proton radiotherapy: Simulation study at different proton beam energies

Authors: A. K. Biegun, Jun Takatsu, M-J. van Goethem, E. R. van der Graaf, M. van Beuzekom, J. Visser, S. Brandenburg

Abstract: To improve the quality of cancer treatment with protons, a translation of X-ray Computed Tomography (CT) images into a map of the proton stopping powers needs to be more accurate. Proton stopping powers determined from CT images have systematic uncertainties in the calculated proton range in a patient of typically 3-4\% and even up to 10\% in region containing bone~\cite{USchneider1995,USchneider1… ▽ More To improve the quality of cancer treatment with protons, a translation of X-ray Computed Tomography (CT) images into a map of the proton stopping powers needs to be more accurate. Proton stopping powers determined from CT images have systematic uncertainties in the calculated proton range in a patient of typically 3-4\% and even up to 10\% in region containing bone~\cite{USchneider1995,USchneider1996,WSchneider2000,GCirrone2007,HPaganetti2012,TPlautz2014,GLandry2013,JSchuemann2014}. As a consequence, part of a tumor may receive no dose, or a very high dose can be delivered in healthy ti\-ssues and organs at risks~(e.g. brain stem)~\cite{ACKnopf2013}. A transmission radiograph of high-energy protons measuring proton stopping powers directly will allow to reduce these uncertainties, and thus improve the quality of treatment. The best way to obtain a sufficiently accurate radiograph is by tracking individual protons traversing the phantom (patient)~\cite{GCirrone2007,TPlautz2014,VSipala2013}. In our simulations we have used an ideal position sensitive detectors measuring a single proton before and after a phantom, while the residual energy of a proton was detected by a BaF$_{2}$ crystal. To obtain transmission radiographs, diffe\-rent phantom materials have been irradiated with a 3x3~cm$^{2}$ scattered proton beam, with various beam energies. The simulations were done using the Geant4 simulation package~\cite{SAgostinelli2003}. In this study we focus on the simulations of the energy loss radiographs for various proton beam energies that are clinically available in proton radiotherapy. △ Less

Submitted 29 January, 2016; originally announced January 2016.

Comments: 6 pages, 6 figures, Presented at Jagiellonian Symposium on Fundamental and Applied Subatomic Physics, 7-12 June, 2015, Kraków, Poland

Characterisation of Medipix3 Silicon Detectors in a Charged-Particle Beam

Authors: K. Akiba, R. Aoude, J. Alozy, M. van Beuzekom, J. Buytaert, P. Collins, A. Dosil Suárez, R. Dumps, A. Gallas, C. Hombach, D. Hynds, M. John, A. Leflat, Y. Li, E. Pérez Trigo, R. Plackett, M. M. Reid, P. Rodríguez Pérez, H. Schindler, P. Tsopelas, C. Vázquez Sierra, J. J. Velthuis, M. Wysokiński

Abstract: While designed primarily for X-ray imaging applications, the Medipix3 ASIC can also be used for charged-particle tracking. In this work, results from a beam test at the CERN SPS with irradiated and non-irradiated sensors are presented and shown to be in agreement with simulation, demonstrating the suitability of the Medipix3 ASIC as a tool for characterising pixel sensors. While designed primarily for X-ray imaging applications, the Medipix3 ASIC can also be used for charged-particle tracking. In this work, results from a beam test at the CERN SPS with irradiated and non-irradiated sensors are presented and shown to be in agreement with simulation, demonstrating the suitability of the Medipix3 ASIC as a tool for characterising pixel sensors. △ Less

Submitted 12 January, 2016; v1 submitted 8 September, 2015; originally announced September 2015.

Comments: 16 pages, 13 figures

Report number: LHCb-PUB-2016-002

Journal ref: JINST 11 (2016) P01011

Advanced Virgo: a 2nd generation interferometric gravitational wave detector

Authors: F. Acernese, M. Agathos, K. Agatsuma, D. Aisa, N. Allemandou, A. Allocca, J. Amarni, P. Astone, G. Balestri, G. Ballardin, F. Barone, J. -P. Baronick, M. Barsuglia, A. Basti, F. Basti, Th. S. Bauer, V. Bavigadda, M. Bejger, M. G. Beker, C. Belczynski, D. Bersanetti, A. Bertolini, M. Bitossi, M. A. Bizouard, S. Bloemen , et al. (209 additional authors not shown)

Abstract: Advanced Virgo is the project to upgrade the Virgo interferometric detector of gravitational waves, with the aim of increasing the number of observable galaxies (and thus the detection rate) by three orders of magnitude. The project is now in an advanced construction phase and the assembly and integration will be completed by the end of 2015. Advanced Virgo will be part of a network with the two A… ▽ More Advanced Virgo is the project to upgrade the Virgo interferometric detector of gravitational waves, with the aim of increasing the number of observable galaxies (and thus the detection rate) by three orders of magnitude. The project is now in an advanced construction phase and the assembly and integration will be completed by the end of 2015. Advanced Virgo will be part of a network with the two Advanced LIGO detectors in the US and GEO HF in Germany, with the goal of contributing to the early detections of gravitational waves and to opening a new observation window on the universe. In this paper we describe the main features of the Advanced Virgo detector and outline the status of the construction. △ Less

Submitted 16 October, 2014; v1 submitted 18 August, 2014; originally announced August 2014.

Comments: Submitted to Classical and Quantum Gravity. 55 pages, 29 figures

Journal ref: Class. Quantum Grav. 32 (2015) 024001

Performance of the LHCb Vertex Locator

Authors: LHCb VELO Group, R. Aaij, A. Affolder, K. Akiba, M. Alexander, S. Ali, R. B. Appleby, M. Artuso, A. Bates, A. Bay, O. Behrendt, J. Benton, M. van Beuzekom, P. M. Bjørnstad, G. Bogdanova, S. Borghi, A. Borgia, T. J. V. Bowcock, J. van den Brand, H. Brown, J. Buytaert, O. Callot, J. Carroll, G. Casse, P. Collins , et al. (79 additional authors not shown)

Abstract: The Vertex Locator (VELO) is a silicon microstrip detector that surrounds the proton-proton interaction region in the LHCb experiment. The performance of the detector during the first years of its physics operation is reviewed. The system is operated in vacuum, uses a bi-phase CO2 cooling system, and the sensors are moved to 7 mm from the LHC beam for physics data taking. The performance and stabi… ▽ More The Vertex Locator (VELO) is a silicon microstrip detector that surrounds the proton-proton interaction region in the LHCb experiment. The performance of the detector during the first years of its physics operation is reviewed. The system is operated in vacuum, uses a bi-phase CO2 cooling system, and the sensors are moved to 7 mm from the LHC beam for physics data taking. The performance and stability of these characteristic features of the detector are described, and details of the material budget are given. The calibration of the timing and the data processing algorithms that are implemented in FPGAs are described. The system performance is fully characterised. The sensors have a signal to noise ratio of approximately 20 and a best hit resolution of 4 microns is achieved at the optimal track angle. The typical detector occupancy for minimum bias events in standard operating conditions in 2011 is around 0.5%, and the detector has less than 1% of faulty strips. The proximity of the detector to the beam means that the inner regions of the n+-on-n sensors have undergone space-charge sign inversion due to radiation damage. The VELO performance parameters that drive the experiment's physics sensitivity are also given. The track finding efficiency of the VELO is typically above 98% and the modules have been aligned to a precision of 1 micron for translations in the plane transverse to the beam. A primary vertex resolution of 13 microns in the transverse plane and 71 microns along the beam axis is achieved for vertices with 25 tracks. An impact parameter resolution of less than 35 microns is achieved for particles with transverse momentum greater than 1 GeV/c. △ Less

Submitted 10 September, 2014; v1 submitted 30 May, 2014; originally announced May 2014.

Comments: 61 pages, 33 figures Minor typographical changes made during journal review are implemented in this version

Report number: CERN-LHCb-DP-2014-001

Journal ref: 2014 JINST 9 P09007

The Timepix Telescope for High Performance Particle Tracking

Authors: Kazuyoshi Akiba, Per Arne Ronning, Martin van Beuzekom, Vincent van Beveren, Silvia Borghi, Henk Boterenbrood, Jan Buytaert, Paula Collins, Alvaro Dosil Suarez, Raphael Dumps, Lars Eklund, Daniel Esperante, Abraham Gallas, Hamish Gordon, Bas van der Heijden, Christoph Hombach, Daniel Hynds, Malcolm John, Alexander Leflat, Yi Ming Li, Ian Longstaff, Alexander Morton, Noritsugu Nakatsuka, Andre Nomerotski, Chris Parkes , et al. (10 additional authors not shown)

Abstract: The Timepix particle tracking telescope has been developed as part of the LHCb VELO Upgrade project, supported by the Medipix Collaboration and the AIDA framework. It is a primary piece of infrastructure for the VELO Upgrade project and is being used for the development of new sensors and front end technologies for several upcoming LHC trackers and vertexing systems. The telescope is designed arou… ▽ More The Timepix particle tracking telescope has been developed as part of the LHCb VELO Upgrade project, supported by the Medipix Collaboration and the AIDA framework. It is a primary piece of infrastructure for the VELO Upgrade project and is being used for the development of new sensors and front end technologies for several upcoming LHC trackers and vertexing systems. The telescope is designed around the dual capability of the Timepix ASICs to provide information about either the deposited charge or the timing information from tracks traversing the 14 x 14mm matrix of 55 x 55 um pixels. The rate of reconstructed tracks available is optimised by taking advantage of the shutter driven readout architecture of the Timepix chip, operated with existing readout systems. Results of tests conducted in the SPS North Area beam facility at CERN show that the telescope typically provides reconstructed track rates during the beam spills of between 3.5 and 7.5 kHz, depending on beam conditions. The tracks are time stamped with 1 ns resolution with an efficiency of above 98% and provide a pointing resolution at the centre of the telescope of 1.6 um . By dropping the time stamping requirement the rate can be increased to 15 kHz, at the expense of a small increase in background. The telescope infrastructure provides CO2 cooling and a flexible mechanical interface to the device under test, and has been used for a wide range of measurements during the 2011-2012 data taking campaigns. △ Less

Submitted 18 April, 2013; originally announced April 2013.

Comments: 14 pages, 9 figures

Radiation damage in the LHCb Vertex Locator

Authors: A. Affolder, K. Akiba, M. Alexander, S. Ali, M. Artuso, J. Benton, M. van Beuzekom, P. M. Bjørnstad, G. Bogdanova, S. Borghi, T. J. V. Bowcock, H. Brown, J. Buytaert, G. Casse, P. Collins, S. De Capua, D. Dossett, L. Eklund, C. Farinelli, J. Garofoli, M. Gersabeck, T. Gershon, H. Gordon, J. Harrison, V. Heijne , et al. (26 additional authors not shown)

Abstract: The LHCb Vertex Locator (VELO) is a silicon strip detector designed to reconstruct charged particle trajectories and vertices produced at the LHCb interaction region. During the first two years of data collection, the 84 VELO sensors have been exposed to a range of fluences up to a maximum value of approximately $\rm{45 \times 10^{12}\,1\,MeV}$ neutron equivalent ($\rm{1\,MeV\,n_{eq}}$). At the op… ▽ More The LHCb Vertex Locator (VELO) is a silicon strip detector designed to reconstruct charged particle trajectories and vertices produced at the LHCb interaction region. During the first two years of data collection, the 84 VELO sensors have been exposed to a range of fluences up to a maximum value of approximately $\rm{45 \times 10^{12}\,1\,MeV}$ neutron equivalent ($\rm{1\,MeV\,n_{eq}}$). At the operational sensor temperature of approximately $-7\,^{\circ}\rm{C}$, the average rate of sensor current increase is $18\,\upmu\rm{A}$ per $\rm{fb^{-1}}$, in excellent agreement with predictions. The silicon effective bandgap has been determined using current versus temperature scan data after irradiation, with an average value of $E_{g}=1.16\pm0.03\pm0.04\,\rm{eV}$ obtained. The first observation of n-on-n sensor type inversion at the LHC has been made, occurring at a fluence of around $15 \times 10 ^{12}$ of $1\,\rm{MeV\,n_{eq}}$. The only n-on-p sensors in use at the LHC have also been studied. With an initial fluence of approximately $\rm{3 \times 10^{12}\,1\,MeV\,n_{eq}}$, a decrease in the Effective Depletion Voltage (EDV) of around 25\,V is observed, attributed to oxygen induced removal of boron interstitial sites. Following this initial decrease, the EDV increases at a comparable rate to the type inverted n-on-n type sensors, with rates of $(1.43\pm 0.16) \times 10 ^{-12}\,\rm{V} / \, 1 \, \rm{MeV\,n_{eq}}$ and $(1.35\pm 0.25) \times 10 ^{-12}\,\rm{V} / \, 1 \, \rm{MeV\,n_{eq}}$ measured for n-on-p and n-on-n type sensors, respectively. A reduction in the charge collection efficiency due to an unexpected effect involving the second metal layer readout lines is observed. △ Less

Submitted 21 February, 2013; originally announced February 2013.

Report number: CERN-LHCb-DP-2012-005

Absolute luminosity measurements with the LHCb detector at the LHC

Authors: The LHCb Collaboration, R. Aaij, B. Adeva, M. Adinolfi, C. Adrover, A. Affolder, Z. Ajaltouni, J. Albrecht, F. Alessio, M. Alexander, G. Alkhazov, P. Alvarez Cartelle, A. A. Alves Jr, S. Amato, Y. Amhis, J. Anderson, R. B. Appleby, O. Aquines Gutierrez, F. Archilli, L. Arrabito, A. Artamonov, M. Artuso, E. Aslanides, G. Auriemma, S. Bachmann , et al. (549 additional authors not shown)

Abstract: Absolute luminosity measurements are of general interest for colliding-beam experiments at storage rings. These measurements are necessary to determine the absolute cross-sections of reaction processes and are valuable to quantify the performance of the accelerator. Using data taken in 2010, LHCb has applied two methods to determine the absolute scale of its luminosity measurements for proton-prot… ▽ More Absolute luminosity measurements are of general interest for colliding-beam experiments at storage rings. These measurements are necessary to determine the absolute cross-sections of reaction processes and are valuable to quantify the performance of the accelerator. Using data taken in 2010, LHCb has applied two methods to determine the absolute scale of its luminosity measurements for proton-proton collisions at the LHC with a centre-of-mass energy of 7 TeV. In addition to the classic "van der Meer scan" method a novel technique has been developed which makes use of direct imaging of the individual beams using beam-gas and beam-beam interactions. This beam imaging method is made possible by the high resolution of the LHCb vertex detector and the close proximity of the detector to the beams, and allows beam parameters such as positions, angles and widths to be determined. The results of the two methods have comparable precision and are in good agreement. Combining the two methods, an overall precision of 3.5% in the absolute luminosity determination is reached. The techniques used to transport the absolute luminosity calibration to the full 2010 data-taking period are presented. △ Less

Submitted 11 January, 2012; v1 submitted 13 October, 2011; originally announced October 2011.

Comments: 48 pages, 19 figures. Results unchanged, improved clarity of Table 6, 9 and 10 and corresponding explanation in the text

Report number: LHCb-PAPER-2011-015; CERN-PH-EP-2011-157

Journal ref: 2012 JINST 7 P01010

Charged Particle Tracking with the Timepix ASIC

Authors: Kazuyoshi Akiba, Marina Artuso, Ryan Badman, Alessandra Borgia, Richard Bates, Florian Bayer, Martin van Beuzekom, Jan Buytaert, Enric Cabruja, Michael Campbell, Paula Collins, Michael Crossley, Raphael Dumps, Lars Eklund, Daniel Esperante, Celeste Fleta, Abraham Gallas, Miriam Gandelman, Justin Garofoli, Marco Gersabeck, Vladimir V. Gligorov, Hamish Gordon, Erik H. M. Heijne, Veerle Heijne, Daniel Hynds , et al. (17 additional authors not shown)

Abstract: A prototype particle tracking telescope has been constructed using Timepix and Medipix ASIC hybrid pixel assemblies as the six sensing planes. Each telescope plane consisted of one 1.4 cm2 assembly, providing a 256x256 array of 55 micron square pixels. The telescope achieved a pointing resolution of 2.3 micron at the position of the device under test. During a beam test in 2009 the telescope was u… ▽ More A prototype particle tracking telescope has been constructed using Timepix and Medipix ASIC hybrid pixel assemblies as the six sensing planes. Each telescope plane consisted of one 1.4 cm2 assembly, providing a 256x256 array of 55 micron square pixels. The telescope achieved a pointing resolution of 2.3 micron at the position of the device under test. During a beam test in 2009 the telescope was used to evaluate in detail the performance of two Timepix hybrid pixel assemblies; a standard planar 300 micron thick sensor, and 285 micron thick double sided 3D sensor. This paper describes a detailed charge calibration study of the pixel devices, which allows the true charge to be extracted, and reports on measurements of the charge collection characteristics and Landau distributions. The planar sensor achieved a best resolution of 4.0 micron for angled tracks, and resolutions of between 4.4 and 11 micron for perpendicular tracks, depending on the applied bias voltage. The double sided 3D sensor, which has significantly less charge sharing, was found to have an optimal resolution of 9.0 micron for angled tracks, and a resolution of 16.0 micron for perpendicular tracks. Based on these studies it is concluded that the Timepix ASIC shows an excellent performance when used as a device for charged particle tracking. △ Less

Submitted 14 June, 2011; v1 submitted 14 March, 2011; originally announced March 2011.

Comments: 51 pages, 39 figures. Submitted to Nucl. Phys. Meth. A. ; Contact authors: P. Collins and V. V. Gligorov

Report number: LHCb-PUB-2011-010