-
ML-based muon identification using a FNAL-NICADD scintillator chamber for the MID subsystem of ALICE 3
Authors:
Jesus Eduardo Muñoz Mendez,
Antonio Ortiz,
Alom Antonio Paz Jimenez,
Paola Vargas Torres,
Ruben Alfaro Molina,
Laura Helena González Trueba,
Varlen Grabski,
Arturo Fernandez Tellez,
Hector David Regules Medel,
Mario Rodriguez Cahuantzi,
Guillermo Tejeda Muñoz,
Yael Antonio Vasquez Beltran,
Juan Carlos Cabanillas Noris,
Solangel Rojas Torres,
Gergely Gabor Barnafoldi,
Daniel Szaraz,
Dezso Varga,
Robert Vertesi,
Edmundo Garciaa Solis
Abstract:
The ALICE Collaboration is planning to construct a new detector (ALICE 3) aiming at exploiting the potential of the high-luminosity Large Hadron Collider (LHC). The new detector will allow ALICE to participate in LHC Run 5 scheduled from 2036 to 2041. The muon-identifier subsystem (MID) is part of the ALICE 3 reference detector layout. The MID will consist of a standard magnetic iron absorber (…
▽ More
The ALICE Collaboration is planning to construct a new detector (ALICE 3) aiming at exploiting the potential of the high-luminosity Large Hadron Collider (LHC). The new detector will allow ALICE to participate in LHC Run 5 scheduled from 2036 to 2041. The muon-identifier subsystem (MID) is part of the ALICE 3 reference detector layout. The MID will consist of a standard magnetic iron absorber ($\approx4$ nuclear interaction lengths) followed by muon chambers. The baseline option for the MID chambers considers plastic scintillation bars equipped with wave-length shifting fibers and readout with silicon photomultipliers. This paper reports on the performance of a MID chamber prototype using 3 GeV/$c$ pion- and muon-enriched beams delivered by the CERN Proton Synchrotron (PS). The prototype was built using extruded plastic scintillator produced by FNAL-NICADD (Fermi National Accelerator Laboratory - Northern Illinois Center for Accelerator and Detector Development). The prototype was experimentally evaluated using varying absorber thicknesses (60, 70, 80, 90, and 100 cm) to assess its performance. The analysis was performed using Machine Learning techniques and the performance was validated with GEANT 4 simulations. Potential improvements in both hardware and data analysis are discussed.
△ Less
Submitted 3 July, 2025;
originally announced July 2025.
-
Future Circular Collider Feasibility Study Report: Volume 2, Accelerators, Technical Infrastructure and Safety
Authors:
M. Benedikt,
F. Zimmermann,
B. Auchmann,
W. Bartmann,
J. P. Burnet,
C. Carli,
A. Chancé,
P. Craievich,
M. Giovannozzi,
C. Grojean,
J. Gutleber,
K. Hanke,
A. Henriques,
P. Janot,
C. Lourenço,
M. Mangano,
T. Otto,
J. Poole,
S. Rajagopalan,
T. Raubenheimer,
E. Todesco,
L. Ulrici,
T. Watson,
G. Wilkinson,
A. Abada
, et al. (1439 additional authors not shown)
Abstract:
In response to the 2020 Update of the European Strategy for Particle Physics, the Future Circular Collider (FCC) Feasibility Study was launched as an international collaboration hosted by CERN. This report describes the FCC integrated programme, which consists of two stages: an electron-positron collider (FCC-ee) in the first phase, serving as a high-luminosity Higgs, top, and electroweak factory;…
▽ More
In response to the 2020 Update of the European Strategy for Particle Physics, the Future Circular Collider (FCC) Feasibility Study was launched as an international collaboration hosted by CERN. This report describes the FCC integrated programme, which consists of two stages: an electron-positron collider (FCC-ee) in the first phase, serving as a high-luminosity Higgs, top, and electroweak factory; followed by a proton-proton collider (FCC-hh) at the energy frontier in the second phase.
FCC-ee is designed to operate at four key centre-of-mass energies: the Z pole, the WW production threshold, the ZH production peak, and the top/anti-top production threshold - delivering the highest possible luminosities to four experiments. Over 15 years of operation, FCC-ee will produce more than 6 trillion Z bosons, 200 million WW pairs, nearly 3 million Higgs bosons, and 2 million top anti-top pairs. Precise energy calibration at the Z pole and WW threshold will be achieved through frequent resonant depolarisation of pilot bunches. The sequence of operation modes remains flexible.
FCC-hh will operate at a centre-of-mass energy of approximately 85 TeV - nearly an order of magnitude higher than the LHC - and is designed to deliver 5 to 10 times the integrated luminosity of the HL-LHC. Its mass reach for direct discovery extends to several tens of TeV. In addition to proton-proton collisions, FCC-hh is capable of supporting ion-ion, ion-proton, and lepton-hadron collision modes.
This second volume of the Feasibility Study Report presents the complete design of the FCC-ee collider, its operation and staging strategy, the full-energy booster and injector complex, required accelerator technologies, safety concepts, and technical infrastructure. It also includes the design of the FCC-hh hadron collider, development of high-field magnets, hadron injector options, and key technical systems for FCC-hh.
△ Less
Submitted 25 April, 2025;
originally announced May 2025.
-
Future Circular Collider Feasibility Study Report: Volume 3, Civil Engineering, Implementation and Sustainability
Authors:
M. Benedikt,
F. Zimmermann,
B. Auchmann,
W. Bartmann,
J. P. Burnet,
C. Carli,
A. Chancé,
P. Craievich,
M. Giovannozzi,
C. Grojean,
J. Gutleber,
K. Hanke,
A. Henriques,
P. Janot,
C. Lourenço,
M. Mangano,
T. Otto,
J. Poole,
S. Rajagopalan,
T. Raubenheimer,
E. Todesco,
L. Ulrici,
T. Watson,
G. Wilkinson,
P. Azzi
, et al. (1439 additional authors not shown)
Abstract:
Volume 3 of the FCC Feasibility Report presents studies related to civil engineering, the development of a project implementation scenario, and environmental and sustainability aspects. The report details the iterative improvements made to the civil engineering concepts since 2018, taking into account subsurface conditions, accelerator and experiment requirements, and territorial considerations. I…
▽ More
Volume 3 of the FCC Feasibility Report presents studies related to civil engineering, the development of a project implementation scenario, and environmental and sustainability aspects. The report details the iterative improvements made to the civil engineering concepts since 2018, taking into account subsurface conditions, accelerator and experiment requirements, and territorial considerations. It outlines a technically feasible and economically viable civil engineering configuration that serves as the baseline for detailed subsurface investigations, construction design, cost estimation, and project implementation planning. Additionally, the report highlights ongoing subsurface investigations in key areas to support the development of an improved 3D subsurface model of the region.
The report describes development of the project scenario based on the 'avoid-reduce-compensate' iterative optimisation approach. The reference scenario balances optimal physics performance with territorial compatibility, implementation risks, and costs. Environmental field investigations covering almost 600 hectares of terrain - including numerous urban, economic, social, and technical aspects - confirmed the project's technical feasibility and contributed to the preparation of essential input documents for the formal project authorisation phase. The summary also highlights the initiation of public dialogue as part of the authorisation process. The results of a comprehensive socio-economic impact assessment, which included significant environmental effects, are presented. Even under the most conservative and stringent conditions, a positive benefit-cost ratio for the FCC-ee is obtained. Finally, the report provides a concise summary of the studies conducted to document the current state of the environment.
△ Less
Submitted 25 April, 2025;
originally announced May 2025.
-
Future Circular Collider Feasibility Study Report: Volume 1, Physics, Experiments, Detectors
Authors:
M. Benedikt,
F. Zimmermann,
B. Auchmann,
W. Bartmann,
J. P. Burnet,
C. Carli,
A. Chancé,
P. Craievich,
M. Giovannozzi,
C. Grojean,
J. Gutleber,
K. Hanke,
A. Henriques,
P. Janot,
C. Lourenço,
M. Mangano,
T. Otto,
J. Poole,
S. Rajagopalan,
T. Raubenheimer,
E. Todesco,
L. Ulrici,
T. Watson,
G. Wilkinson,
P. Azzi
, et al. (1439 additional authors not shown)
Abstract:
Volume 1 of the FCC Feasibility Report presents an overview of the physics case, experimental programme, and detector concepts for the Future Circular Collider (FCC). This volume outlines how FCC would address some of the most profound open questions in particle physics, from precision studies of the Higgs and EW bosons and of the top quark, to the exploration of physics beyond the Standard Model.…
▽ More
Volume 1 of the FCC Feasibility Report presents an overview of the physics case, experimental programme, and detector concepts for the Future Circular Collider (FCC). This volume outlines how FCC would address some of the most profound open questions in particle physics, from precision studies of the Higgs and EW bosons and of the top quark, to the exploration of physics beyond the Standard Model. The report reviews the experimental opportunities offered by the staged implementation of FCC, beginning with an electron-positron collider (FCC-ee), operating at several centre-of-mass energies, followed by a hadron collider (FCC-hh). Benchmark examples are given of the expected physics performance, in terms of precision and sensitivity to new phenomena, of each collider stage. Detector requirements and conceptual designs for FCC-ee experiments are discussed, as are the specific demands that the physics programme imposes on the accelerator in the domains of the calibration of the collision energy, and the interface region between the accelerator and the detector. The report also highlights advances in detector, software and computing technologies, as well as the theoretical tools /reconstruction techniques that will enable the precision measurements and discovery potential of the FCC experimental programme. This volume reflects the outcome of a global collaborative effort involving hundreds of scientists and institutions, aided by a dedicated community-building coordination, and provides a targeted assessment of the scientific opportunities and experimental foundations of the FCC programme.
△ Less
Submitted 25 April, 2025;
originally announced May 2025.
-
MATHUSLA: An External Long-Lived Particle Detector to Maximize the Discovery Potential of the HL-LHC
Authors:
Branden Aitken,
Cristiano Alpigiani,
Juan Carlos Arteaga-Velázquez,
Mitchel Baker,
Kincso Balazs,
Jared Barron,
Brian Batell,
Austin Batz,
Yan Benhammou,
Tamara Alice Bud,
Karen Salomé Caballero-Mora,
John Paul Chou,
David Curtin,
Albert de Roeck,
Miriam Diamond,
Mariia Didenko,
Keith R. Dienes,
William Dougherty,
Liam Andrew Dougherty,
Marco Drewes,
Sameer Erramilli,
Erez Etzion,
Arturo Fernández Téllez,
Grace Finlayson,
Oliver Fischer
, et al. (48 additional authors not shown)
Abstract:
We present the current status of the MATHUSLA (MAssive Timing Hodoscope for Ultra-Stable neutraL pArticles) long-lived particle (LLP) detector at the HL-LHC, covering the design, fabrication and installation at CERN Point 5. MATHUSLA40 is a 40 m-scale detector with an air-filled decay volume that is instrumented with scintillator tracking detectors, to be located near CMS. Its large size, close pr…
▽ More
We present the current status of the MATHUSLA (MAssive Timing Hodoscope for Ultra-Stable neutraL pArticles) long-lived particle (LLP) detector at the HL-LHC, covering the design, fabrication and installation at CERN Point 5. MATHUSLA40 is a 40 m-scale detector with an air-filled decay volume that is instrumented with scintillator tracking detectors, to be located near CMS. Its large size, close proximity to the CMS interaction point and about 100 m of rock shielding from LHC backgrounds allows it to detect LLP production rates and lifetimes that are one to two orders of magnitude beyond the ultimate reach of the LHC main detectors. This provides unique sensitivity to many LLP signals that are highly theoretically motivated, due to their connection to the hierarchy problem, the nature of dark matter, and baryogenesis. Data taking is projected to commence with the start of HL-LHC operations. We summarize the new 40m design for the detector that was recently presented in the MATHUSLA Conceptual Design Report, alongside new realistic background and signal simulations that demonstrate high efficiency for the main target LLP signals in a background-free HL-LHC search. We argue that MATHUSLA's uniquely robust expansion of the HL-LHC physics reach is a crucial ingredient in CERN's mission to search for new physics and characterize the Higgs boson with precision.
△ Less
Submitted 1 April, 2025;
originally announced April 2025.
-
Conceptual Design Report for the MATHUSLA Long-Lived Particle Detector near CMS
Authors:
Branden Aitken,
Cristiano Alpigiani,
Juan Carlos Arteaga-Velázquez,
Mitchel Baker,
Kincso Balazs,
Jared Barron,
Brian Batell,
Austin Batz,
Yan Benhammou,
Tamara Alice Bud,
Karen Salomé Caballero-Mora,
John Paul Chou,
David Curtin,
Albert de Roeck,
Miriam Diamond,
Mariia Didenko,
Keith R. Dienes,
William Dougherty,
Liam Andrew Dougherty,
Marco Drewes,
Sameer Erramilli,
Erez Etzion,
Arturo Fernández Téllez,
Grace Finlayson,
Oliver Fischer
, et al. (48 additional authors not shown)
Abstract:
We present the Conceptual Design Report (CDR) for the MATHUSLA (MAssive Timing Hodoscope for Ultra-Stable neutraL pArticles) long-lived particle detector at the HL-LHC, covering the design, fabrication and installation at CERN Point 5. MATHUSLA is a 40 m-scale detector with an air-filled decay volume that is instrumented with scintillator tracking detectors, to be located near CMS. Its large size,…
▽ More
We present the Conceptual Design Report (CDR) for the MATHUSLA (MAssive Timing Hodoscope for Ultra-Stable neutraL pArticles) long-lived particle detector at the HL-LHC, covering the design, fabrication and installation at CERN Point 5. MATHUSLA is a 40 m-scale detector with an air-filled decay volume that is instrumented with scintillator tracking detectors, to be located near CMS. Its large size, close proximity to the CMS interaction point and about 100 m of rock shielding from HL-LHC backgrounds allows it to detect LLP production rates and lifetimes that are one to two orders of magnitude beyond the ultimate sensitivity of the HL-LHC main detectors for many highly motivated LLP signals. Data taking is projected to commence with the start of HL-LHC operations. We present a new 40m design for the detector: its individual scintillator bars and wavelength-shifting fibers, their organization into tracking layers, tracking modules, tower modules and the veto detector; define a high-level design for the supporting electronics, DAQ and trigger system, including supplying a hardware trigger signal to CMS to record the LLP production event; outline computing systems, civil engineering and safety considerations; and present preliminary cost estimates and timelines for the project. We also conduct detailed simulation studies of the important cosmic ray and HL-LHC muon backgrounds, implementing full track/vertex reconstruction and background rejection, to ultimately demonstrate high signal efficiency and $\ll 1$ background event in realistic LLP searches for the main physics targets at MATHUSLA. This sensitivity is robust with respect to detector design or background simulation details. Appendices provide various supplemental information.
△ Less
Submitted 26 March, 2025;
originally announced March 2025.
-
Cosmic Piano: analysing the sound of the Universe
Authors:
Guillermo Tejeda Muñoz,
Luis Alberto Perez Moreno,
Simone Ragoni,
Hector David Regules Medel,
Arturo Fernández Téllez,
Yael Antonio Vasquez Beltran
Abstract:
We present the Cosmic Piano, an innovative outreach tool designed to detect muons from air showers produced by cosmic rays colliding with the atmosphere. The Cosmic Piano consists of scintillator-based modules with avalanche photodiodes (APD) readout, which produce a musical note and a flash of light whenever a muon passes through one of them and triggers its electronics. The Cosmic Piano has been…
▽ More
We present the Cosmic Piano, an innovative outreach tool designed to detect muons from air showers produced by cosmic rays colliding with the atmosphere. The Cosmic Piano consists of scintillator-based modules with avalanche photodiodes (APD) readout, which produce a musical note and a flash of light whenever a muon passes through one of them and triggers its electronics. The Cosmic Piano has been showcased at various high-profile events, including the Montreux Jazz Festival and the EuroScience Open Forum, seamlessly fusing scientific phenomena with live music. Building on its success, we have developed a new, comprehensive Masterclass session aimed at engaging high school and university students. This session includes analysing both simulated cosmic ray events and real data from the Cosmic Piano. The Masterclass provides participants with a hands-on experience that mirrors the experimental procedures used in major physics experiments, such as those conducted at CERN with the Large Hadron Collider (LHC) collision data. This initiative offers a unique opportunity for students to engage with an active experiment, bridging the gap between outreach and serious scientific research.
△ Less
Submitted 23 September, 2024;
originally announced September 2024.
-
Characterisation of plastic scintillator paddles and lightweight MWPCs for the MID subsystem of ALICE 3
Authors:
Ruben Alfaro,
Mauricio Alvarado Hernández,
Gyula Bencédi,
Juan Carlos Cabanillas Noris,
Marco Antonio Díaz Maldonado,
Carlos Duarte Galvan,
Arturo Fernández Téllez,
Gergely Gábor Barnaföldi,
Ádám Gera,
Varlen Grabsky,
Gergő Hamar,
Gerardo Herrera Corral,
Ildefonso León Monzón,
Josué Martínez García,
Mario Iván Martínez Hernandez,
Jesús Eduardo Muñoz Méndez,
Richárd Nagy,
Rafael Ángel Narcio Laveaga,
Antonio Ortiz,
Mario Rodríguez Cahuantzi,
Solangel Rojas Torres,
Timea Szollosova,
Miguel Enrique Patiño Salazar,
Jared Pazarán García,
Hector David Regules Medel
, et al. (7 additional authors not shown)
Abstract:
The ALICE collaboration is proposing a completely new detector, ALICE 3, for operation during the LHC Runs 5 and 6. One of the ALICE~3 subsystems is the Muon IDentifier detector (MID), which has to be optimised to be efficient for the reconstruction of $J/ψ$ at rest (muons down to $p_{\rm T}\approx1.5$ GeV/$c$) for $|η|<1.3$. Given the modest particle flux expected in the MID of a few Hz/cm$^2$, t…
▽ More
The ALICE collaboration is proposing a completely new detector, ALICE 3, for operation during the LHC Runs 5 and 6. One of the ALICE~3 subsystems is the Muon IDentifier detector (MID), which has to be optimised to be efficient for the reconstruction of $J/ψ$ at rest (muons down to $p_{\rm T}\approx1.5$ GeV/$c$) for $|η|<1.3$. Given the modest particle flux expected in the MID of a few Hz/cm$^2$, technologies like plastic scintillator bars ($\approx1$ m length) equipped with wavelength-shifting fibers and silicon photomultiplier readout, and lightweight Multi-Wire Proportional Chambers (MWPCs) are under investigation. To this end, different plastic scintillator paddles and MWPCs were studied at the CERN T10 test beam facility. This paper reports on the performance of the scintillator prototypes tested at different beam momenta (from 0.5 GeV/$c$ up to 6 GeV/$c$) and positions (horizontal, vertical, and angular scans). The MWPCs were tested at different momenta (from 0.5 GeV/$c$ to 10 GeV/$c$) and beam intensities, their efficiency and position resolutions were verified beyond the particle rates expected with the MID in ALICE 3.
△ Less
Submitted 16 February, 2024; v1 submitted 9 January, 2024;
originally announced January 2024.
-
Cosmic-ray searches with the MATHUSLA detector
Authors:
Cristiano Alpigiani,
J. C. Arteaga-Velázquez,
Daniela Blanco-Lira,
Davide Boscherini,
K. S. Caballero-Mora,
Paolo Camarri,
Roberto Cardarelli,
Dennis Cazar Ramírez,
Giuseppe Di Sciascio,
Arturo Fernández Téllez,
H. J. Lubatti,
O. G. Morales-Olivares,
Piter Amador Paye Mamani,
David Rivera Rangel,
Mario Rodríguez-Cahuantzi,
Rinaldo Santonico,
Martin Alfonso Subieta Vázquez
Abstract:
The performance of the proposed MATHUSLA detector as an instrument for studying the physics of cosmic rays by measuring extensive air showers is presented. The MATHUSLA detector is designed to observe and study the decay of long-lived particles produced at the pp interaction point of the CMS detector at CERN during the HL-LHC data-taking period. The proposed MATHUSLA detector will be composed of m…
▽ More
The performance of the proposed MATHUSLA detector as an instrument for studying the physics of cosmic rays by measuring extensive air showers is presented. The MATHUSLA detector is designed to observe and study the decay of long-lived particles produced at the pp interaction point of the CMS detector at CERN during the HL-LHC data-taking period. The proposed MATHUSLA detector will be composed of many layers of long scintillating bars that cannot measure more than one hit per bar and correctly report the hit coordinate in case of multiple hits. This study shows that adding a layer of RPC detectors with both analogue and digital readout significantly enhances the capabilities of MATHUSLA to measure the local densities and arrival times of charged particles at the front of air showers. We discuss open issues in cosmic-ray physics that the proposed MATHUSLA detector with an additional layer of RPC detectors could address and conclude by comparing with other air-shower facilities that measure cosmic rays in the PeV energy range.
△ Less
Submitted 13 November, 2023;
originally announced November 2023.
-
Mobility strategies based on percolation theory to avoid the spread of diseases: COVID-19
Authors:
Diana Rosales Herrera,
J. E. Ramírez,
Jorge Velázquez-Castro,
Bogar Díaz,
M. I. Martínez,
P. Vázquez Juárez,
A. Fernández Téllez
Abstract:
Human mobility is an important factor in the propagation of infectious diseases. In particular, the spatial spread of a disease is a consequence of human mobility. On the other hand, the control strategies based on mobility restrictions are generally unpopular and costly. These high social and economic costs make it very important to design global protocols where the cost is minimized and effect…
▽ More
Human mobility is an important factor in the propagation of infectious diseases. In particular, the spatial spread of a disease is a consequence of human mobility. On the other hand, the control strategies based on mobility restrictions are generally unpopular and costly. These high social and economic costs make it very important to design global protocols where the cost is minimized and effects maximized. In this work, we calculate the percolation threshold of the spread in a network of a disease. In particular, we found the number of roads to close and regions to isolate in the Puebla State, Mexico, to avoid the global spread of COVID-19. Computational simulations taking into account the proposed strategy show a potential reduction of 94% of infections. This methodology can be used in broader and different areas to help in the design of health policies.
--
La movilidad de las personas es uno de los principales factores que propician la propagación de epidemias. En particular, es el factor que genera el esparcimiento de la enfermedad en diferentes regiones. Las medidas de control epidemiológico basadas en la restricción de movilidad son generalmente poco populares y las consecuencias económicas pueden llegar a ser muy grandes. Debido a los altos costos de estas medidas, es de gran relevancia tener estrategias globales que optimicen las medidas minimizando los costos. En este trabajo, se calcula el umbral de percolación de la propagación de enfermedades en redes. De manera particular, se encuentra el número de caminos a restringir y localidades que tienen que ser aisladas para limitar la propagación global de COVID-19 en el Estado de Puebla, México. Simulaciones computacionales donde se implementan las medidas de restricción de movilidad entre los diferentes municipios, junto con las medidas de confinamiento, muestran que es posible reducir un 94% de la población afectada comparado con el caso en el que no se implementa ninguna medida. Esta metodología puede ser aplicada a distintas zonas para ayudar a las autoridades de salud en la toma de decisiones.
△ Less
Submitted 23 May, 2021;
originally announced May 2021.
-
An Update to the Letter of Intent for MATHUSLA: Search for Long-Lived Particles at the HL-LHC
Authors:
Cristiano Alpigiani,
Juan Carlos Arteaga-Velázquez,
Austin Ball,
Liron Barak,
Jared Barron,
Brian Batell,
James Beacham,
Yan Benhammo,
Karen Salomé Caballero-Mora,
Paolo Camarri,
Roberto Cardarelli,
John Paul Chou,
Wentao Cui,
David Curtin,
Miriam Diamond,
Keith R. Dienes,
Liam Andrew Dougherty,
Giuseppe Di Sciascio,
Marco Drewes,
Erez Etzion,
Rouven Essig,
Jared Evans,
Arturo Fernández Téllez,
Oliver Fischer,
Jim Freeman
, et al. (58 additional authors not shown)
Abstract:
We report on recent progress in the design of the proposed MATHUSLA Long Lived Particle (LLP) detector for the HL-LHC, updating the information in the original Letter of Intent (LoI), see CDS:LHCC-I-031, arXiv:1811.00927. A suitable site has been identified at LHC Point 5 that is closer to the CMS Interaction Point (IP) than assumed in the LoI. The decay volume has been increased from 20 m to 25 m…
▽ More
We report on recent progress in the design of the proposed MATHUSLA Long Lived Particle (LLP) detector for the HL-LHC, updating the information in the original Letter of Intent (LoI), see CDS:LHCC-I-031, arXiv:1811.00927. A suitable site has been identified at LHC Point 5 that is closer to the CMS Interaction Point (IP) than assumed in the LoI. The decay volume has been increased from 20 m to 25 m in height. Engineering studies have been made in order to locate much of the decay volume below ground, bringing the detector even closer to the IP. With these changes, a 100 m x 100 m detector has the same physics reach for large c$τ$ as the 200 m x 200 m detector described in the LoI and other studies. The performance for small c$τ$ is improved because of the proximity to the IP. Detector technology has also evolved while retaining the strip-like sensor geometry in Resistive Plate Chambers (RPC) described in the LoI. The present design uses extruded scintillator bars read out using wavelength shifting fibers and silicon photomultipliers (SiPM). Operations will be simpler and more robust with much lower operating voltages and without the use of greenhouse gases. Manufacturing is straightforward and should result in cost savings. Understanding of backgrounds has also significantly advanced, thanks to new simulation studies and measurements taken at the MATHUSLA test stand operating above ATLAS in 2018. We discuss next steps for the MATHUSLA collaboration, and identify areas where new members can make particularly important contributions.
△ Less
Submitted 3 September, 2020;
originally announced September 2020.
-
Performance of ALICE AD modules in the CERN PS test beam
Authors:
M. Broz,
J. C. Cabanillas Noris,
E. Calvo Villar,
C. Duarte Galvan,
E. Endress,
L. G. Espinoza Beltran,
A. Fernandez Tellez,
D. Finogeev,
A. M. Gago,
G. Herrera Corral,
T. Kim,
A. Kurepin,
A. B. Kurepin,
N. Kurepin,
I. Leon Monzon,
M. I. Martinez Hernandez,
C. Mayer,
M. M. Mieskolainen,
R. Orava,
L. A. Perez Moreno,
J. -P. Revol,
M. Rodriguez Cahuantzi,
S. Rojas Torres,
D. Serebryakov,
A. Shabanov
, et al. (2 additional authors not shown)
Abstract:
Two modules of the AD detector have been studied with the test beam at the T10 facility at CERN. The AD detector is made of scintillator pads read out by wave-length shifters (WLS)coupled to clean fibres that carry the produced light to photo-multiplier tubes (PMTs). In ALICE the AD is used to trigger and study the physics of diffractive and ultra-peripheral collisions as well as for a variety of…
▽ More
Two modules of the AD detector have been studied with the test beam at the T10 facility at CERN. The AD detector is made of scintillator pads read out by wave-length shifters (WLS)coupled to clean fibres that carry the produced light to photo-multiplier tubes (PMTs). In ALICE the AD is used to trigger and study the physics of diffractive and ultra-peripheral collisions as well as for a variety of technical tasks like beam-gas background monitoring or as a luminometer. The position dependence of the modules' efficiency has been measured and the effect of hits on the WLS or PMTs has been evaluated. The charge deposited by pions and protons has been measured at different momenta of the test beam. The time resolution is determined as a function of the deposited charge. These results are important ingredients to better understand the AD detector, to benchmark the corresponding simulations, and very importantly they served as a baseline for a similar device, the Forward Diffractive Detector (FDD), being currently built and that will be in operation in ALICE during the LHC Runs 3 and 4.
△ Less
Submitted 26 June, 2020;
originally announced June 2020.
-
Site-bond percolation solution to preventing the propagation of \textit{Phytophthora} zoospores on plantations
Authors:
J. E. Ramírez,
C. Pajares,
M. I. Martínez,
R. Rodríguez Fernández,
E. Molina-Gayosso,
J. Lozada-Lechuga,
A. Fernández Téllez
Abstract:
We propose a strategy based on the site-bond percolation to minimize the propagation of \textit{Phytophthora} zoospores on plantations, consisting in introducing physical barriers between neighboring plants. Two clustering processes are distinguished: i) one of cells with the presence of the pathogen, detected on soil analysis; and ii) that of diseased plants, revealed from a visual inspection of…
▽ More
We propose a strategy based on the site-bond percolation to minimize the propagation of \textit{Phytophthora} zoospores on plantations, consisting in introducing physical barriers between neighboring plants. Two clustering processes are distinguished: i) one of cells with the presence of the pathogen, detected on soil analysis; and ii) that of diseased plants, revealed from a visual inspection of the plantation. The former is well described by the standard site-bond percolation. In the latter, the percolation threshold is fitted by a Tsallis distribution when no barriers are introduced. We provide, for both cases, the formulae for the minimal barrier density to prevent the emergence of the spanning cluster. Though this work is focused on a specific pathogen, the model presented here can also be applied to prevent the spreading of other pathogens that disseminate, by other means, from one plant to the neighboring ones. Finally, the application of this strategy to three types of commercialy important Mexican chili plants is also shown.
△ Less
Submitted 20 April, 2020;
originally announced April 2020.
-
A next-generation LHC heavy-ion experiment
Authors:
D. Adamová,
G. Aglieri Rinella,
M. Agnello,
Z. Ahammed,
D. Aleksandrov,
A. Alici,
A. Alkin,
T. Alt,
I. Altsybeev,
D. Andreou,
A. Andronic,
F. Antinori,
P. Antonioli,
H. Appelshäuser,
R. Arnaldi,
I. C. Arsene,
M. Arslandok,
R. Averbeck,
M. D. Azmi,
X. Bai,
R. Bailhache,
R. Bala,
L. Barioglio,
G. G. Barnaföldi,
L. S. Barnby
, et al. (374 additional authors not shown)
Abstract:
The present document discusses plans for a compact, next-generation multi-purpose detector at the LHC as a follow-up to the present ALICE experiment. The aim is to build a nearly massless barrel detector consisting of truly cylindrical layers based on curved wafer-scale ultra-thin silicon sensors with MAPS technology, featuring an unprecedented low material budget of 0.05% X$_0$ per layer, with th…
▽ More
The present document discusses plans for a compact, next-generation multi-purpose detector at the LHC as a follow-up to the present ALICE experiment. The aim is to build a nearly massless barrel detector consisting of truly cylindrical layers based on curved wafer-scale ultra-thin silicon sensors with MAPS technology, featuring an unprecedented low material budget of 0.05% X$_0$ per layer, with the innermost layers possibly positioned inside the beam pipe. In addition to superior tracking and vertexing capabilities over a wide momentum range down to a few tens of MeV/$c$, the detector will provide particle identification via time-of-flight determination with about 20~ps resolution. In addition, electron and photon identification will be performed in a separate shower detector. The proposed detector is conceived for studies of pp, pA and AA collisions at luminosities a factor of 20 to 50 times higher than possible with the upgraded ALICE detector, enabling a rich physics program ranging from measurements with electromagnetic probes at ultra-low transverse momenta to precision physics in the charm and beauty sector.
△ Less
Submitted 2 May, 2019; v1 submitted 31 January, 2019;
originally announced February 2019.
-
A Letter of Intent for MATHUSLA: a dedicated displaced vertex detector above ATLAS or CMS
Authors:
Cristiano Alpigiani,
Austin Ball,
Liron Barak,
James Beacham,
Yan Benhammo,
Tingting Cao,
Paolo Camarri,
Roberto Cardarelli,
Mario Rodriguez-Cahuantzi,
John Paul Chou,
David Curtin,
Miriam Diamond,
Giuseppe Di Sciascio,
Marco Drewes,
Sarah C. Eno,
Erez Etzion,
Rouven Essig,
Jared Evans,
Oliver Fischer,
Stefano Giagu,
Brandon Gomes,
Andy Haas,
Yuekun Heng,
Giuseppe Iaselli,
Ken Johns
, et al. (39 additional authors not shown)
Abstract:
In this Letter of Intent (LOI) we propose the construction of MATHUSLA (MAssive Timing Hodoscope for Ultra-Stable neutraL pArticles), a dedicated large-volume displaced vertex detector for the HL-LHC on the surface above ATLAS or CMS. Such a detector, which can be built using existing technologies with a reasonable budget in time for the HL-LHC upgrade, could search for neutral long-lived particle…
▽ More
In this Letter of Intent (LOI) we propose the construction of MATHUSLA (MAssive Timing Hodoscope for Ultra-Stable neutraL pArticles), a dedicated large-volume displaced vertex detector for the HL-LHC on the surface above ATLAS or CMS. Such a detector, which can be built using existing technologies with a reasonable budget in time for the HL-LHC upgrade, could search for neutral long-lived particles (LLPs) with up to several orders of magnitude better sensitivity than ATLAS or CMS, while also acting as a cutting-edge cosmic ray telescope at CERN to explore many open questions in cosmic ray and astro-particle physics. We review the physics motivations for MATHUSLA and summarize its LLP reach for several different possible detector geometries, as well as outline the cosmic ray physics program. We present several updated background studies for MATHUSLA, which help inform a first detector-design concept utilizing modular construction with Resistive Plate Chambers (RPCs) as the primary tracking technology. We present first efficiency and reconstruction studies to verify the viability of this design concept, and we explore some aspects of its total cost. We end with a summary of recent progress made on the MATHUSLA test stand, a small-scale demonstrator experiment currently taking data at CERN Point 1, and finish with a short comment on future work.
△ Less
Submitted 2 November, 2018;
originally announced November 2018.
-
SuperB Technical Design Report
Authors:
SuperB Collaboration,
M. Baszczyk,
P. Dorosz,
J. Kolodziej,
W. Kucewicz,
M. Sapor,
A. Jeremie,
E. Grauges Pous,
G. E. Bruno,
G. De Robertis,
D. Diacono,
G. Donvito,
P. Fusco,
F. Gargano,
F. Giordano,
F. Loddo,
F. Loparco,
G. P. Maggi,
V. Manzari,
M. N. Mazziotta,
E. Nappi,
A. Palano,
B. Santeramo,
I. Sgura,
L. Silvestris
, et al. (384 additional authors not shown)
Abstract:
In this Technical Design Report (TDR) we describe the SuperB detector that was to be installed on the SuperB e+e- high luminosity collider. The SuperB asymmetric collider, which was to be constructed on the Tor Vergata campus near the INFN Frascati National Laboratory, was designed to operate both at the Upsilon(4S) center-of-mass energy with a luminosity of 10^{36} cm^{-2}s^{-1} and at the tau/ch…
▽ More
In this Technical Design Report (TDR) we describe the SuperB detector that was to be installed on the SuperB e+e- high luminosity collider. The SuperB asymmetric collider, which was to be constructed on the Tor Vergata campus near the INFN Frascati National Laboratory, was designed to operate both at the Upsilon(4S) center-of-mass energy with a luminosity of 10^{36} cm^{-2}s^{-1} and at the tau/charm production threshold with a luminosity of 10^{35} cm^{-2}s^{-1}. This high luminosity, producing a data sample about a factor 100 larger than present B Factories, would allow investigation of new physics effects in rare decays, CP Violation and Lepton Flavour Violation. This document details the detector design presented in the Conceptual Design Report (CDR) in 2007. The R&D and engineering studies performed to arrive at the full detector design are described, and an updated cost estimate is presented.
A combination of a more realistic cost estimates and the unavailability of funds due of the global economic climate led to a formal cancelation of the project on Nov 27, 2012.
△ Less
Submitted 24 June, 2013;
originally announced June 2013.
