-
Radiated energy fraction of SPI-induced disruptions at ASDEX Upgrade
Authors:
Paul Heinrich,
Gergely Papp,
Stefan Jachmich,
Javier Artola,
Matthias Bernert,
Pascal de Marné,
Mathias Dibon,
Ralph Dux,
Thomas Eberl,
Jörg Hobirk,
Michael Lehnen,
Tobias Peherstorfer,
Nina Schwarz,
Umar Sheikh,
Bernhard Sieglin,
Jakub Svoboda,
the ASDEX Upgrade Team,
the EUROfusion Tokamak Exploitation Team
Abstract:
Future large tokamaks will operate at high plasma currents and high stored plasma energies. To ensure machine protection in case of a sudden loss of plasma confinement (major disruption), a large fraction of the magnetic and thermal energy must be radiated to reduce thermal loads. The disruption mitigation system for ITER is based on massive material injection in the form of shattered pellet injec…
▽ More
Future large tokamaks will operate at high plasma currents and high stored plasma energies. To ensure machine protection in case of a sudden loss of plasma confinement (major disruption), a large fraction of the magnetic and thermal energy must be radiated to reduce thermal loads. The disruption mitigation system for ITER is based on massive material injection in the form of shattered pellet injection (SPI). To support ITER, a versatile SPI system was installed at the tokamak ASDEX Upgrade (AUG). The AUG SPI features three independent pellet generation cells and guide tubes, and each was equipped with different shatter heads for the 2022 experimental campaign. We dedicated over 200 plasma discharges to the study of SPI plasma termination, and in this manuscript report on the results of bolometry (total radiation) analysis. The amount of neon inside the pellets is the dominant factor determining the radiated energy fraction ($f_{rad}$). Large and fast fragments, produced by the 12.5° rectangular shatter head, lead to somewhat higher values of frad compared to the 25° circular or rectangular heads. This effect is strongest for neon content of $< 3\times10^{20}$ neon atoms ($f_\textrm{neon} \lesssim 1.25\%$ neon) injected, where a lower normal velocity component (larger fragments) seems slightly beneficial. While full-sized, 8 mm diameter, 100% deuterium ($D_2$) pellets lead to a disruption, the 4 mm or shortened 8 mm pellets of 100% $D_2$ did not. The disruption threshold for 100% $D_2$ is found to be around $1\times10^{22}$ $D_2$ molecules inside the pellet. While the radiated energy fraction of non-disruptive SPI is below 20%, this is increased to 40% during the TQ and VDE phase of the disruptive injections. For ($D_2$-Ne-mix pellets, frad values of $< 90$% are observed, and the curve saturates around 80% for 10% neon mixed into the 8 mm pellets ($2\times10^{21}$ neon atoms).
△ Less
Submitted 16 April, 2025; v1 submitted 1 October, 2024;
originally announced October 2024.
-
Divertor Heat Load in ASDEX Upgrade L-Mode in Presence of External Magnetic Perturbation
Authors:
Michael Faitsch,
Bernhard Sieglin,
Thomas Eich,
Albrecht Herrmann,
Wolfgang Suttrop,
the ASDEX Upgrade Team
Abstract:
Power exhaust is one of the major challenges for a future fusion device. Applying a non-axisymmetric external magnetic perturbation is one technique that is studied in order to mitigate or suppress large edge localized modes which accompany the high confinement regime in tokamaks. The external magnetic perturbation brakes the axisymmetry of a tokamak and leads to a 2D heat flux pattern on the dive…
▽ More
Power exhaust is one of the major challenges for a future fusion device. Applying a non-axisymmetric external magnetic perturbation is one technique that is studied in order to mitigate or suppress large edge localized modes which accompany the high confinement regime in tokamaks. The external magnetic perturbation brakes the axisymmetry of a tokamak and leads to a 2D heat flux pattern on the divertor target. The 2D heat flux pattern at the outer divertor target is studied on ASDEX Upgrade in stationary L-Mode discharges. The amplitude of the 2D characteristic of the heat flux depends on the alignment between the field lines at the edge and the vacuum response of the applied magnetic perturbation spectrum. The 2D characteristic reduces with increasing density. The increasing divertor broadening $S$ with increasing density is proposed as the main actuator. This is supported by a generic model using field line tracing and the vacuum field approach that is in quantitative agreement with the measured heat flux. The perturbed heat flux, averaged over a full toroidal rotation of the magnetic perturbation, is identical to the non-perturbed heat flux without magnetic perturbation. The transport qualifiers, power fall-off length $λ_q$ and divertor broadening $S$, are the same within the uncertainty compared to the unperturbed reference. No additional cross field transport is observed.
△ Less
Submitted 9 March, 2017;
originally announced March 2017.
-
Analytic 1D Approximation of the Divertor Broadening S in the Divertor Region for Conductive Heat Transport
Authors:
Dirk Nille,
Bernhard Sieglin,
Thomas Eich
Abstract:
Topic is the divertor broadening $S$, being a result of perpendicular transport in the scrape-off layer and resulting in a better distribution of the power load onto the divertor target. Recent studies show a scaling of the divertor broadening with an inverse power law to the target temperature $T_t$, promising its reduction to be a way of distributing the power entering the divertor volume onto a…
▽ More
Topic is the divertor broadening $S$, being a result of perpendicular transport in the scrape-off layer and resulting in a better distribution of the power load onto the divertor target. Recent studies show a scaling of the divertor broadening with an inverse power law to the target temperature $T_t$, promising its reduction to be a way of distributing the power entering the divertor volume onto a large surface area.
It is shown that for pure conductive transport in the divertor region the suggested inverse power law scaling to $T_t$ is only valid for high target electron temperatures. For decreasing target temperatures ($T_t < 20\,$eV) the increase of $S$ stagnates and the conductive model results in a finite value of $S$ even for zero target temperature. It is concluded that the target temperature is no valid parameter for a power law scaling, as it is not representative for the entire divertor volume. This is shown in simulations solving the 2D heat diffusion equation, which is used as reference for an analytic 1D model describing the divertor broadening along a field line solely by the ratio of the perpendicular to the parallel diffusivity.
By assuming the temperature dependence of these two quantities an integral form of $S$ is derived, relying only on the temperature distribution along the separatrix between X-point and target. Integration along the separatrix results in an approximation for $S$, being in agreement with the 2D simulations. This model is also applicable to scenarios including heat losses, e.g. due to radiation.
Convective transport can not be neglected for high recycling conditions, hence the derived expression for $S$ is not expected to hold. However, based on the non-vanishing parallel transport, respective the finite parallel transport time, the divertor broadening is expected to reach a finite value.
△ Less
Submitted 13 October, 2016;
originally announced October 2016.
-
Effect of resonant magnetic perturbations on low collisionality discharges in MAST and a comparison with ASDEX Upgrade
Authors:
A. Kirk,
W. Suttrop,
Yueqiang Liu,
I. T. Chapman,
P. Cahyna,
T. Eich,
C. Fuchs,
C. Ham,
J. R. Harrison,
M W. Jakubowski,
S. Pamela,
M. Peterka,
D. Ryan,
S. Saarelma,
R. Scannell,
A. J. Thornton,
M. Valovic,
B. Sieglin,
L. Barrera Orte,
M. Willensdorfer,
B. Kurzan,
R. Fischer
Abstract:
Sustained ELM mitigation has been achieved on MAST and AUG using RMPs with a range of toroidal mode numbers over a wide region of low to medium collisionality discharges. The ELM energy loss and peak heat loads at the divertor targets have been reduced. The ELM mitigation phase is typically associated with a drop in plasma density and overall stored energy. In one particular scenario on MAST, by c…
▽ More
Sustained ELM mitigation has been achieved on MAST and AUG using RMPs with a range of toroidal mode numbers over a wide region of low to medium collisionality discharges. The ELM energy loss and peak heat loads at the divertor targets have been reduced. The ELM mitigation phase is typically associated with a drop in plasma density and overall stored energy. In one particular scenario on MAST, by carefully adjusting the fuelling it has been possible to counteract the drop in density and to produce plasmas with mitigated ELMs, reduced peak divertor heat flux and with minimal degradation in pedestal height and confined energy. While the applied resonant magnetic perturbation field can be a good indicator for the onset of ELM mitigation on MAST and AUG there are some cases where this is not the case and which clearly emphasise the need to take into account the plasma response to the applied perturbations. The plasma response calculations show that the increase in ELM frequency is correlated with the size of the edge peeling-tearing like response of the plasma and the distortions of the plasma boundary in the X-point region.
△ Less
Submitted 24 December, 2014;
originally announced December 2014.
-
Contrasting H-mode behaviour with deuterium fuelling and nitrogen seeding in the all-carbon and metallic versions of JET
Authors:
G. P. Maddison,
C. Giroud,
B. Alper,
G. Arnoux,
I. Balboa,
M. N. A. Beurskens,
A. Boboc,
S. Brezinsek,
M. Brix,
M. Clever,
R. Coelho,
J. W. Coenen,
I. Coffey,
P. C. da Silva Aresta Belo,
S. Devaux,
P. Devynck,
T. Eich,
R. C. Felton,
J. Flanagan,
L. Frassinetti,
L. Garzotti,
M. Groth,
S. Jachmich,
A. Järvinen,
E. Joffrin
, et al. (26 additional authors not shown)
Abstract:
The former all-carbon wall on JET has been replaced with beryllium in the main torus and tungsten in the divertor to mimic the surface materials envisaged for ITER. Comparisons are presented between Type I H-mode characteristics in each design by examining respective scans over deuterium fuelling and impurity seeding, required to ameliorate exhaust loads both in JET at full capability and in ITER.
The former all-carbon wall on JET has been replaced with beryllium in the main torus and tungsten in the divertor to mimic the surface materials envisaged for ITER. Comparisons are presented between Type I H-mode characteristics in each design by examining respective scans over deuterium fuelling and impurity seeding, required to ameliorate exhaust loads both in JET at full capability and in ITER.
△ Less
Submitted 11 June, 2014;
originally announced June 2014.
-
Impact of nitrogen seeding on confinement and power load control of a high-triangularity JET ELMy H-mode plasma with a metal wall
Authors:
C Giroud,
G P Maddison,
S Jachmich,
F Rimini,
M N A Beurskens,
I Balboa,
S Brezinsek,
R Coelho,
J W Coenen,
L Frassinetti,
E Joffrin,
M Oberkofler,
M Lehnen,
Y Liu,
S Marsen,
K McCormick K,
A Meigs,
R Neu,
B Sieglin,
G van Rooij,
G Arnoux,
P Belo,
M Brix,
M Clever,
I Coffey
, et al. (17 additional authors not shown)
Abstract:
This paper reports the impact on confinement and power load of the high-shape 2.5MA ELMy H-mode scenario at JET of a change from an all carbon plasma facing components to an all metal wall. In preparation to this change, systematic studies of power load reduction and impact on confinement as a result of fuelling in combination with nitrogen seeding were carried out in JET-C and are compared to the…
▽ More
This paper reports the impact on confinement and power load of the high-shape 2.5MA ELMy H-mode scenario at JET of a change from an all carbon plasma facing components to an all metal wall. In preparation to this change, systematic studies of power load reduction and impact on confinement as a result of fuelling in combination with nitrogen seeding were carried out in JET-C and are compared to their counterpart in JET with a metallic wall. An unexpected and significant change is reported on the decrease of the pedestal confinement but is partially recovered with the injection of nitrogen.
△ Less
Submitted 31 October, 2013;
originally announced October 2013.
