-
Exploring unique design features of the Monolithic Stitched Sensor with Timing (MOST): yield, powering, timing, and sensor reverse bias
Authors:
Mariia Selina,
R. Barthel,
S. Bugiel,
L. Cecconi,
J. De Melo,
M. Fransen,
A. Grelli,
I. Hobus,
A. Isakov,
A. Junique,
P. Leitao,
M. Mager,
Y. Otarid,
F. Piro,
M. J. Rossewij,
S. Solokhin,
J. Sonneveld,
W. Snoeys,
N. Tiltmann,
A. Vitkovskiy,
H. Wennloef
Abstract:
Monolithic stitched CMOS sensors are explored for the upgrade of Inner Tracking System of the ALICE experiment (ITS3) and the R&D of the CERN Experimental Physics Department. To learn about stitching, two 26 cm long stitched sensors, the Monolithic Stitched Sensor (MOSS), and the Monolithic Stitched Sensor with Timing (MOST), were implemented in the Engineering Round 1 (ER1) in the TPSCo 65nm ISC…
▽ More
Monolithic stitched CMOS sensors are explored for the upgrade of Inner Tracking System of the ALICE experiment (ITS3) and the R&D of the CERN Experimental Physics Department. To learn about stitching, two 26 cm long stitched sensors, the Monolithic Stitched Sensor (MOSS), and the Monolithic Stitched Sensor with Timing (MOST), were implemented in the Engineering Round 1 (ER1) in the TPSCo 65nm ISC technology. Contrary to the MOSS, powered by 20 distinct power domains accessible from separate pads, the MOST has one global analog and digital power domain to or from which small fractions of the matrix can be connected or disconnected by conservatively designed power switches to prevent shorts or defects from affecting the full chip. Instead of the synchronous readout in the MOSS, the MOST immediately transfers hit information upon a hit, preserving timing information. The sensor reverse bias is also applied through the bias of the front-end rather than by a reverse substrate bias. This paper presents the first characterization results of the MOST, with the focus on its specific characteristics, including yield analysis, precise timing measurements, and the potential of its alternative biasing approach for improved sensor performance.
△ Less
Submitted 18 April, 2025;
originally announced April 2025.
-
Electrical/piezoresistive effects in bent Alpide MAPS
Authors:
M. J. Rossewij,
E. M. Okkinga,
H. M. Naqvi,
R. G. E. Barthel,
S. R. Alving
Abstract:
The ITS3 upgrade baseline design employs MAPS (Monolithic Active Pixel Sensor) in bent state. Bending experiments with the existing ITS2 MAPS (=Alpide chip) show it remains functional but with relative large analog supply current changes. It is shown that by the piezoresistive effect, rotation of current mirror FETs can be responsible which was confirmed after validating the layout. Measured Gauge…
▽ More
The ITS3 upgrade baseline design employs MAPS (Monolithic Active Pixel Sensor) in bent state. Bending experiments with the existing ITS2 MAPS (=Alpide chip) show it remains functional but with relative large analog supply current changes. It is shown that by the piezoresistive effect, rotation of current mirror FETs can be responsible which was confirmed after validating the layout. Measured Gauge Factor has proper sign but is 3 times lower than typical values derived from literature. The magnitude of the measured strain induced PMOS V$_{th}$ shift is as expected but the sign differs for compressive strain with some of the literature.
△ Less
Submitted 18 March, 2024;
originally announced March 2024.
-
A Large-Scale Pad-Sensor Based Prototype of the Silicon Tungsten Electromagnetic Calorimeter for the Forward Direction in ALICE at LHC
Authors:
R. G. E. Barthel,
T. Chujo,
T. Hachiya,
M. Hatakeyama,
Y. Hoshi,
M. Inaba,
Y.,
Kawamura,
D. Kawana,
C. Loizides,
Y. Miake,
Y. Minato,
K. Nakagawa,
N. Novitzky,
T. Peitzmann,
M. Rossewij,
M. Shimomura,
T. Sugitate,
T. Suzuki,
K. Tadokoro,
M. Takamura,
S. Takasu,
A. van den Brink,
M. van Leeuwen
Abstract:
We constructed a large-scale electromagnetic calorimeter prototype as a part of the Forward Calorimeter upgrade project (FoCal) for the ALICE experiment at the Large Hadron Collider (LHC). The prototype, also known as ``Mini FoCal'', consists of 20 layers of silicon pad sensors and tungsten alloy plates with printed circuit boards and readout electronics. The constructed detector was tested at the…
▽ More
We constructed a large-scale electromagnetic calorimeter prototype as a part of the Forward Calorimeter upgrade project (FoCal) for the ALICE experiment at the Large Hadron Collider (LHC). The prototype, also known as ``Mini FoCal'', consists of 20 layers of silicon pad sensors and tungsten alloy plates with printed circuit boards and readout electronics. The constructed detector was tested at the test beam facility of the Super Proton Synchrotron (SPS) at CERN. We obtain an energy resolution of about 4.3% for electron beams at both 150 and 250 GeV/$c$, which is consistent with realistic detector response simulations. Longitudinal profiles of electromagnetic shower were also measured and found to agree with the simulations. The same prototype detector was installed in the ALICE experimental area about 7.5m away from the interaction point. It was used to measure inclusive electromagnetic cluster energy distributions and neutral-pion candidate invariant mass distributions for pseudo-rapidity of $η$=3.7-4.5 in proton-proton collisions at $\sqrt{s}$ = 13 TeV at LHC. The measured distributions in different $η$ regions are similar to those obtained from PYTHIA simulations.
△ Less
Submitted 18 March, 2024; v1 submitted 9 June, 2023;
originally announced June 2023.
-
Performance of the Electromagnetic Pixel Calorimeter Prototype EPICAL-2
Authors:
J. Alme,
R. Barthel,
A. van Bochove,
V. Borshchov,
R. Bosley,
A. van den Brink,
E. Broeils,
H. Büsching,
V. N. Eikeland,
O. S. Groettvik,
Y. H. Han,
N. van der Kolk,
J. H. Kim,
T. J. Kim,
Y. Kwon,
M. Mager,
Q. W. Malik,
E. Okkinga,
T. Y. Park,
T. Peitzmann,
F. Pliquett,
M. Protsenko,
F. Reidt,
S. van Rijk,
K. Røed
, et al. (9 additional authors not shown)
Abstract:
The first evaluation of an ultra-high granularity digital electromagnetic calorimeter prototype using 1.0-5.8 GeV/c electrons is presented. The $25\times10^6$ pixel detector consists of 24 layers of ALPIDE CMOS MAPS sensors, with a pitch of around 30~$μ$m, and has a depth of almost 20 radiation lengths of tungsten absorber. Ultra-thin cables allow for a very compact design. The properties that are…
▽ More
The first evaluation of an ultra-high granularity digital electromagnetic calorimeter prototype using 1.0-5.8 GeV/c electrons is presented. The $25\times10^6$ pixel detector consists of 24 layers of ALPIDE CMOS MAPS sensors, with a pitch of around 30~$μ$m, and has a depth of almost 20 radiation lengths of tungsten absorber. Ultra-thin cables allow for a very compact design. The properties that are critical for physics studies are measured: electromagnetic shower response, energy resolution and linearity. The stochastic energy resolution is comparable with the state-of-the art resolution for a Si-W calorimeter, with data described well by a simulation model using GEANT and Allpix$^2$. The performance achieved makes this technology a good candidate for use in the ALICE FoCal upgrade, and in general demonstrates the strong potential for future applications in high-energy physics.
△ Less
Submitted 28 December, 2022; v1 submitted 6 September, 2022;
originally announced September 2022.
-
Results from the EPICAL-2 Ultra-High Granularity Electromagnetic Calorimeter Prototype
Authors:
T. Peitzmann,
J. Alme,
R. Barthel,
A. van Bochove,
V. Borshchov,
R. Bosley,
A. van den Brink,
E. Broeils,
H. Büsching,
V. N. Eikeland,
O. S. Groettvik,
Y. H. Han,
N. van der Kolk,
J. H. Kim,
T. J. Kim,
Y. Kwon,
M. Mager,
Q. W. Malik,
E. Okkinga,
T. Y. Park,
F. Pliquett,
M. Protsenko,
F. Reidt,
S. van Rijk,
K. Røed
, et al. (9 additional authors not shown)
Abstract:
A prototype of a new type of calorimeter has been designed and constructed, based on a silicon-tungsten sampling design using pixel sensors with digital readout. It makes use of the Alpide MAPS sensor developed for the ALICE ITS upgrade. A binary readout is possible due to the pixel size of $\approx 30 \times 30 \, μ\mathrm{m}^2$. This prototype has been successfully tested with cosmic muons and w…
▽ More
A prototype of a new type of calorimeter has been designed and constructed, based on a silicon-tungsten sampling design using pixel sensors with digital readout. It makes use of the Alpide MAPS sensor developed for the ALICE ITS upgrade. A binary readout is possible due to the pixel size of $\approx 30 \times 30 \, μ\mathrm{m}^2$. This prototype has been successfully tested with cosmic muons and with test beams at DESY and the CERN SPS. We report on performance results obtained at DESY, showing good energy resolution and linearity, and compare to detailed MC simulations. Also shown are preliminary results of the high-energy performance as measured at the SPS. The two-shower separation capabilities are discussed.
△ Less
Submitted 27 September, 2022; v1 submitted 5 July, 2022;
originally announced July 2022.
-
First demonstration of in-beam performance of bent Monolithic Active Pixel Sensors
Authors:
ALICE ITS project,
:,
G. Aglieri Rinella,
M. Agnello,
B. Alessandro,
F. Agnese,
R. S. Akram,
J. Alme,
E. Anderssen,
D. Andreou,
F. Antinori,
N. Apadula,
P. Atkinson,
R. Baccomi,
A. Badalà,
A. Balbino,
C. Bartels,
R. Barthel,
F. Baruffaldi,
I. Belikov,
S. Beole,
P. Becht,
A. Bhatti,
M. Bhopal,
N. Bianchi
, et al. (230 additional authors not shown)
Abstract:
A novel approach for designing the next generation of vertex detectors foresees to employ wafer-scale sensors that can be bent to truly cylindrical geometries after thinning them to thicknesses of 20-40$μ$m. To solidify this concept, the feasibility of operating bent MAPS was demonstrated using 1.5$\times$3cm ALPIDE chips. Already with their thickness of 50$μ$m, they can be successfully bent to ra…
▽ More
A novel approach for designing the next generation of vertex detectors foresees to employ wafer-scale sensors that can be bent to truly cylindrical geometries after thinning them to thicknesses of 20-40$μ$m. To solidify this concept, the feasibility of operating bent MAPS was demonstrated using 1.5$\times$3cm ALPIDE chips. Already with their thickness of 50$μ$m, they can be successfully bent to radii of about 2cm without any signs of mechanical or electrical damage. During a subsequent characterisation using a 5.4GeV electron beam, it was further confirmed that they preserve their full electrical functionality as well as particle detection performance.
In this article, the bending procedure and the setup used for characterisation are detailed. Furthermore, the analysis of the beam test, including the measurement of the detection efficiency as a function of beam position and local inclination angle, is discussed. The results show that the sensors maintain their excellent performance after bending to radii of 2cm, with detection efficiencies above 99.9% at typical operating conditions, paving the way towards a new class of detectors with unprecedented low material budget and ideal geometrical properties.
△ Less
Submitted 17 August, 2021; v1 submitted 27 May, 2021;
originally announced May 2021.
