-
Development of slurry targets for high repetition-rate XFEL experiments
Authors:
Raymond F. Smith,
Vinay Rastogi,
Amy E. Lazicki,
Martin G. Gorman,
Richard Briggs,
Amy L. Coleman,
Carol Davis,
Saransh Singh,
David McGonegle,
Samantha M. Clarke,
Travis Volz,
Trevor Hutchinson,
Christopher McGuire,
Dayne E. Fratanduono,
Damian C. Swift,
Eric Folsom,
Cynthia A. Bolme,
Arianna E. Gleason,
Federica Coppari,
Hae Ja Lee,
Bob Nagler,
Eric Cunningham,
Eduardo Granados,
Phil Heimann,
Richard G. Kraus
, et al. (4 additional authors not shown)
Abstract:
Combining an x-ray free electron laser (XFEL) with high power laser drivers enables the study of phase transitions, equation-of-state, grain growth, strength, and transformation pathways as a function of pressure to 100s GPa along different thermodynamic compression paths. Future high-repetition rate laser operation will enable data to be accumulated at >1 Hz which poses a number of experimental c…
▽ More
Combining an x-ray free electron laser (XFEL) with high power laser drivers enables the study of phase transitions, equation-of-state, grain growth, strength, and transformation pathways as a function of pressure to 100s GPa along different thermodynamic compression paths. Future high-repetition rate laser operation will enable data to be accumulated at >1 Hz which poses a number of experimental challenges including the need to rapidly replenish the target. Here, we present a combined shock-compression and X-ray diffraction study on vol% epoxy(50)-crystalline grains(50) (slurry) targets, which can be fashioned into extruded ribbons for high repetition-rate operation. For shock-loaded NaCl-slurry samples, we observe pressure, density and temperature states within the embedded NaCl grains consistent with observations for shock-compressed single-crystal NaCl.
△ Less
Submitted 11 January, 2022;
originally announced January 2022.
-
Compression of Femtosecond Pulses in a wide Wavelength Range Using a Large Mode Area Tapered Fiber
Authors:
M. Rehan,
G. Kumar,
V. Rastogi,
D. A. Korobko,
A. A. Sysolyatin
Abstract:
We report design of a tapered fiber that can be used for compression of pulses at different central wavelengths. The proposed fiber is a 3-layer W-type large-mode-area fiber, which has been tapered to transform the mode area from 1700 μm2 to 900 μm2. We determine the exact length of the maximum pulse compression and numerically demonstrate the compression of 250 fs, 100 kW peak power input pulse t…
▽ More
We report design of a tapered fiber that can be used for compression of pulses at different central wavelengths. The proposed fiber is a 3-layer W-type large-mode-area fiber, which has been tapered to transform the mode area from 1700 μm2 to 900 μm2. We determine the exact length of the maximum pulse compression and numerically demonstrate the compression of 250 fs, 100 kW peak power input pulse to 15 fs, 850 kW at 1.55 μm wavelength and 250 fs, 120 kW peak power input pulses to 28 fs, 700 kW and to 46 fs, 500 kW at 1.8 μm and 2 μm wavelengths, respectively. Such a fiber can find wide ranging applications including in communication, spectroscopy and medicine.
△ Less
Submitted 22 November, 2018;
originally announced November 2018.
-
Design and analysis of annulus core few mode EDFA for modal gain equalization
Authors:
Ankita Gaur,
Vipul Rastogi
Abstract:
Few-mode fiber amplifier is widely under study to overcome the issue of internet traffic in optical communication. This article proposes annulus core few-mode erbium doped fiber (FM-EDF) with annulus or extra annulus doping for amplification of the LP01, LP11, LP21, and LP31 signal mode groups with low differential modal gain (DMG). Our simulations confirm that extra annulus doping helps in reduci…
▽ More
Few-mode fiber amplifier is widely under study to overcome the issue of internet traffic in optical communication. This article proposes annulus core few-mode erbium doped fiber (FM-EDF) with annulus or extra annulus doping for amplification of the LP01, LP11, LP21, and LP31 signal mode groups with low differential modal gain (DMG). Our simulations confirm that extra annulus doping helps in reducing DMG of higher order mode groups. We have achieved less than 2.2 dB DMG over C-band for 4-mode groups using extra annulus doping. The proposed EDF would be useful for space division multiplexing (SDM) based optical fiber communication system.
△ Less
Submitted 19 January, 2016;
originally announced January 2016.
-
Laser Induced Damage Studies in Borosilicate Glass Using nanosecond and sub nanosecond pulses
Authors:
Vinay Rastogi,
S. Chaurasia,
D. S. Munda
Abstract:
The damage mechanism induced by laser pulse of different duration in borosilicate glass widely used for making confinement geometry targets which are important for laser driven shock multiplication and elongation of pressure pulse, is studied. We measured the front and rear surface damage threshold of borosilicate glass and their dependency on laser parameters. In this paper, we also study the the…
▽ More
The damage mechanism induced by laser pulse of different duration in borosilicate glass widely used for making confinement geometry targets which are important for laser driven shock multiplication and elongation of pressure pulse, is studied. We measured the front and rear surface damage threshold of borosilicate glass and their dependency on laser parameters. In this paper, we also study the thermal effects on the damage diameters, generated at the time of plasma formation. These induced damage width, geometries and microstructure changes are measured and analyzed with optical microscope, scanning electron microscope and Raman spectroscopy. The results show that at low energies symmetrical damages are found and these damage width increases nonlinearly with laser intensity. The emitted optical spectrum during the process of breakdown is also investigated and is used for the characterization of emitted plasma such as plasma temperature and free electron density. Optical emission lines from Si I at 500 nm, Si II at 385nm and Si III at 455 nm are taken for the temperature calculations.
△ Less
Submitted 13 January, 2016;
originally announced January 2016.
-
Large-mode-area leaky optical fibre fabricated by MCVD
Authors:
Bernard Dussardier,
Stanislaw Trzesien,
Michèle Ude,
Vipul Rastogi,
Ajeet Kumar,
Gérard Monnom
Abstract:
A large mode area single-mode optical fibre based on leaky mode filtering was prepared by MCVD. The cladding structure discriminates the fundamental mode from the higher order ones. A preliminary version has 25-$μ$m core diameter and 0.11 numerical aperture. A Gaussian-like mode with 22-$μ$m MFD is observed after 3-m propagation, in agreement with modeling.
A large mode area single-mode optical fibre based on leaky mode filtering was prepared by MCVD. The cladding structure discriminates the fundamental mode from the higher order ones. A preliminary version has 25-$μ$m core diameter and 0.11 numerical aperture. A Gaussian-like mode with 22-$μ$m MFD is observed after 3-m propagation, in agreement with modeling.
△ Less
Submitted 7 February, 2011;
originally announced February 2011.
-
Birefringence analysis of multilayer leaky cladding optical fibre
Authors:
Laurent Labonté,
Vipul Rastogi,
A. Kumar,
Bernard Dussardier,
Gérard Monnom
Abstract:
We analyse a multilayer leaky cladding (MLC) fibre using the finite element method and study the effect of the MLC on the bending loss and birefringence of two types of structures: (i) a circular core large-mode-area structure and (ii) an elliptical-small-core structure. In a large-mode-area structure, we verify that the multilayer leaky cladding strongly discriminates against higher order modes t…
▽ More
We analyse a multilayer leaky cladding (MLC) fibre using the finite element method and study the effect of the MLC on the bending loss and birefringence of two types of structures: (i) a circular core large-mode-area structure and (ii) an elliptical-small-core structure. In a large-mode-area structure, we verify that the multilayer leaky cladding strongly discriminates against higher order modes to achieve single-mode operation, the fibre shows negligible birefringence, and the bending loss of the fibre is low for bending radii larger than 10 cm. In the elliptical-small-core structure we show that the MLC reduces the birefringence of the fibre. This prevents the structure from becoming birefringent in case of any departures from circular geometry. The study should be useful in the designs of MLC fibres for various applications including high power amplifiers, gain flattening of fibre amplifiers and dispersion compensation.
△ Less
Submitted 14 August, 2010; v1 submitted 19 March, 2010;
originally announced March 2010.
-
Co-axial dual-core resonant leaky fibre for optical amplifiers
Authors:
Ajeet Kumar,
Vipul Rastogi,
Charu Kakkar,
Bernard Dussardier
Abstract:
We present a co-axial dual-core resonant leaky optical fibre design, in which the outer core is made highly leaky. A suitable choice of parameters can enable us to resonantly couple power from the inner core to the outer core. In a large-core fibre, such a resonant coupling can considerably increase the differential leakage loss between the fundamental and the higher order modes and can result i…
▽ More
We present a co-axial dual-core resonant leaky optical fibre design, in which the outer core is made highly leaky. A suitable choice of parameters can enable us to resonantly couple power from the inner core to the outer core. In a large-core fibre, such a resonant coupling can considerably increase the differential leakage loss between the fundamental and the higher order modes and can result in effective single-mode operation. In a small-core single-mode fibre, such a coupling can lead to sharp increase in the wavelength dependent leakage loss near the resonant wavelength and can be utilized for the suppression of amplified spontaneous emission and thereby gain equalization of an optical amplifier. We study the propagation characteristics of the fibre using the transfer matrix method and present an example of each, the large-mode-area design for high power amplifiers and the wavelength tunable leakage loss design for inherent gain equalization of optical amplifiers.
△ Less
Submitted 28 February, 2010;
originally announced March 2010.
