Showing 1–50 of 61 results for author: Posen, S

Analysis of Niobium Electropolishing Using a Generalized Distribution of Relaxation Times Method

Authors: Eric Viklund, Vijay Chouhan, Davida Smith, Tim Ring, David N. Seidman, Sam Posen

Abstract: Using electrochemical impedance spectroscopy, we have devised a method of sensing the microscopic surface conditions on the surface of niobium as it is undergoing an electrochemical polishing (EP) treatment. The method uses electrochemical impedance spectroscopy (EIS) to gather information on the surface state of the electrode without disrupting the polishing reaction. The EIS data is analyzed usi… ▽ More Using electrochemical impedance spectroscopy, we have devised a method of sensing the microscopic surface conditions on the surface of niobium as it is undergoing an electrochemical polishing (EP) treatment. The method uses electrochemical impedance spectroscopy (EIS) to gather information on the surface state of the electrode without disrupting the polishing reaction. The EIS data is analyzed using a so-called distribution of relaxation times (DRT) method. Using DRT, the EIS data can be deconvolved into discrete relaxation time peaks without any a priori knowledge of the electrode dynamics. By analyzing the relaxation time peaks, we are able to distinguish two distinct modes of the EP reaction. As the polishing voltage is increased, the electrode transitions from the low voltage EP mode, characterized by a single relaxation time peaks, to the high voltage EP mode, characterized by two relaxation time peaks. We theorize that this second peak is caused by the formation of an oxide layer on the electrode. We also find that this oxide induced peak transitions from to a negative relaxation time, which is indicative of a blocking electrode process. By analyzing EPed samples, we show that samples polished in the low voltage mode have significantly higher surface roughness due to grain etching and faceting. We find that the surface roughness of the samples only improves when the oxide film peak is present and in the negative relaxation time region. This shows that EIS combined with DRT analysis can be used to predict etching on EPed Nb. This method can also be performed before or during the EP, which could allow for adjustment of polishing parameters to guarantee a smooth cavity surface finish. △ Less

Submitted 15 January, 2025; originally announced January 2025.

First characterisation of the MAGO cavity, a superconducting RF detector for kHz-MHz gravitational waves

Authors: Lars Fischer, Bianca Giaccone, Ivan Gonin, Anna Grassellino, Wolfgang Hillert, Timergali Khabiboulline, Tom Krokotsch, Gudrid Moortgat-Pick, Andrea Muhs, Yuriy Orlov, Michel Paulsen, Krisztian Peters, Sam Posen, Oleg Pronitchev, Marc Wenskat

Abstract: Heterodyne detection using microwave cavities is a promising method for detecting high-frequency gravitational waves or ultralight axion dark matter. In this work, we report on studies conducted on a spherical 2-cell cavity developed by the MAGO collaboration for high-frequency gravitational waves detection. Although fabricated around 20 years ago, the cavity had not been used since. Due to deviat… ▽ More Heterodyne detection using microwave cavities is a promising method for detecting high-frequency gravitational waves or ultralight axion dark matter. In this work, we report on studies conducted on a spherical 2-cell cavity developed by the MAGO collaboration for high-frequency gravitational waves detection. Although fabricated around 20 years ago, the cavity had not been used since. Due to deviations from the nominal geometry, we conducted a mechanical survey and performed room-temperature plastic tuning. Measurements and simulations of the mechanical resonances and electromagnetic properties were carried out, as these are critical for estimating the cavity's gravitational wave coupling potential. Based on these results, we plan further studies in a cryogenic environment. The cavity characterisation does not only provide valuable experience for a planned physics run but also informs the future development of improved cavity designs. △ Less

Submitted 17 June, 2025; v1 submitted 27 November, 2024; originally announced November 2024.

Comments: 23 pages, 17 figures

Report number: FERMILAB-PUB-24-0819-SQMS-TD, DESY-24-181

Journal ref: Class. Quantum Grav. 42 (2025) 115015

An Improved Bound on Nonlinear Quantum Mechanics using a Cryogenic Radio Frequency Experiment

Authors: Oleksandr Melnychuk, Bianca Giaccone, Nicholas Bornman, Raphael Cervantes, Anna Grassellino, Roni Harnik, David E. Kaplan, Geev Nahal, Roman Pilipenko, Sam Posen, Surjeet Rajendran, Alexander O. Sushkov

Abstract: There are strong arguments that quantum mechanics may be nonlinear in its dynamics. A discovery of nonlinearity would hint at a novel understanding of the interplay between gravity and quantum field theory, for example. As such, experiments searching for potential nonlinear effects in the electromagnetic sector are important. Here we outline such an experiment, consisting of a stream of random bit… ▽ More There are strong arguments that quantum mechanics may be nonlinear in its dynamics. A discovery of nonlinearity would hint at a novel understanding of the interplay between gravity and quantum field theory, for example. As such, experiments searching for potential nonlinear effects in the electromagnetic sector are important. Here we outline such an experiment, consisting of a stream of random bits (which were generated using Rigetti's Aspen-M-3 chip) as input to an RF signal generator coupled to a cryogenic detector. Projective measurements of the qubit state, which is originally prepared in an equal superposition, serve as the random binary output of a signal generator. Thereafter, spectral analysis of the RF detector would yield a detectable excess signal predicted to arise from such a nonlinear effect. A comparison between the projective measurements of the quantum bits vs the classical baseline showed no power excess. This sets a new limit on the electromagnetic nonlinearity parameter $|ε| \lessapprox 1.15 \times 10^{-12}$, at a 90.0% confidence level. This is the most stringent limit on nonlinear quantum mechanics thus far and an improvement by nearly a factor of 50 over the previous experimental limit. △ Less

Submitted 14 November, 2024; originally announced November 2024.

Report number: FERMILAB-PUB-24-0725-SQMS-T-TD

A Precision Gyroscope from the Helicity of Light

Authors: Michael A. Fedderke, Roni Harnik, David E. Kaplan, Sam Posen, Surjeet Rajendran, Francesco Serra, Vyacheslav P. Yakovlev

Abstract: We describe a gyroscope that measures rotation based on the effects of the rotation on the polarization of light. Rotation induces a differential phase shift in the propagation of left- and right-circularly polarized light and this phase shift can be measured in suitably designed interferometric setups. The signal in this setup is independent of the frequency of light, unlike various sources of no… ▽ More We describe a gyroscope that measures rotation based on the effects of the rotation on the polarization of light. Rotation induces a differential phase shift in the propagation of left- and right-circularly polarized light and this phase shift can be measured in suitably designed interferometric setups. The signal in this setup is independent of the frequency of light, unlike various sources of noise such as vibrations, which cause phase shifts that depend on the frequency. Such vibrations are the practical limit on the sensitivity of conventional Sagnac-style optical interferometers that are typically used as gyroscopes. In the proposed setup, one can potentially mitigate this source of noise by simultaneously using two (or more) sources of light that have different frequencies. The signal in this setup scales with the total storage time of the light. Due to its frequency independence, it is thus most optimal to measure the signal using superconducting radio-frequency systems where the high finesse of the available cavities enables considerably longer storage times than is possible in an optical setup. △ Less

Submitted 2 April, 2025; v1 submitted 23 June, 2024; originally announced June 2024.

Comments: 16 pages, 1 figure. Published version

Report number: FERMILAB-PUB-24-0325-SQMS-TD

Journal ref: Phys. Rev. A 111, 043502 (2025)

Healing Gradient Degradation in Nb3Sn SRF Cavities Using a Recoating Method

Authors: Eric Viklund, David N. Seidman, Brad M. Tennis, Grigory Eremeev, Sam Posen

Abstract: Despite having advantageous superconducting properties, Nb3Sn superconducting radiofrequency (SRF) cavities still have practical challenges compared to Nb SRF cavities due to the brittle nature of Nb3Sn. Performance degradation can occur when a Nb3Sn SRF cavity experiences mechanical stresses such as during handling and tuning of the cavity. In this study, we present a potential treatment for SRF… ▽ More Despite having advantageous superconducting properties, Nb3Sn superconducting radiofrequency (SRF) cavities still have practical challenges compared to Nb SRF cavities due to the brittle nature of Nb3Sn. Performance degradation can occur when a Nb3Sn SRF cavity experiences mechanical stresses such as during handling and tuning of the cavity. In this study, we present a potential treatment for SRF cavities that have experienced stress induced performance degradation that involves a recoating procedure. The degraded cavity is coated with a small amount of Sn using a single step vapor-diffusion methodology. Using this approach we can recover a significant portion of the lost performance of a Nb3Sn SRF cavity. △ Less

Submitted 30 April, 2024; originally announced May 2024.

PI Loop Resonance Control for Dark Photon Experiment at 2 K Using a 2.6 GHz SRF Cavity

Authors: C. Contreras-Martinez, B. Giaccone, O. Melnychuk, A. Netepenko, Y. Pischalnikov, S. Posen, V. Yakovlev

Abstract: Two 2.6 GHz SRF cavities are being used for a dark photon search at the vertical test stand (VTS) in FNAL, for the second phase of the Dark SRF experiment. During testing at 2 K the cavities experience frequency detuning caused by microphonics and slow frequency drifts. The experiment requires that the two cavities have the same frequency within the cavity's bandwidth. These two cavities are equip… ▽ More Two 2.6 GHz SRF cavities are being used for a dark photon search at the vertical test stand (VTS) in FNAL, for the second phase of the Dark SRF experiment. During testing at 2 K the cavities experience frequency detuning caused by microphonics and slow frequency drifts. The experiment requires that the two cavities have the same frequency within the cavity's bandwidth. These two cavities are equipped with frequency tuners consisting of three piezo actuators. The piezo actuators are used for fine-fast frequency tuning. A proportional-integral (PI) loop utilizing the three piezos on the emitter was used to stabilize the cavity frequency and match the receiver cavity frequency. The results from this implementation will be discussed. The integration time was also calculated via simulation. △ Less

Submitted 19 July, 2023; originally announced July 2023.

Comments: 21st International Conference on Radio-Frequency Superconductivity (SRF 2023)

Report number: FERMILAB-CONF-23-264-TD

Testing of the 2.6 GHz SRF Cavity Tuner for the Dark Photon Experiment at 2 K

Authors: C. Contreras-Martinez, B. Giaccone, I. Gonin, T. Khabiboulline, O. Melnychuk, Y. Pischalnikov, S. Posen, O. Pronitchev, JC. Yun

Abstract: At FNAL two single cell 2.6 GHz SRF cavities are being used to search for dark photons, the experiment can be conducted at 2 K or in a dilution refrigerator. Precise frequency tuning is required for these two cavities so they can be matched in frequency. A cooling capacity constraint on the dilution refrigerator only allows piezo actuators to be part of the design of the 2.6 GHz cavity tuner. The… ▽ More At FNAL two single cell 2.6 GHz SRF cavities are being used to search for dark photons, the experiment can be conducted at 2 K or in a dilution refrigerator. Precise frequency tuning is required for these two cavities so they can be matched in frequency. A cooling capacity constraint on the dilution refrigerator only allows piezo actuators to be part of the design of the 2.6 GHz cavity tuner. The tuner is equipped with three encapsulated piezos that deliver long and short-range frequency tuning. Modifications were implemented on the first tuner design due to the low forces on the piezos caused by the cavity. Three brass rods with Belleville washers were added to the design to increase the overall force on the piezos. The testing results at 2 K are presented with the original design tuner and with the modification. △ Less

Submitted 19 July, 2023; originally announced July 2023.

Comments: 21st International Conference on Radio-Frequency Superconductivity (SRF 2023)

Report number: FERMILAB-CONF-23-265-TD

Preservation of the High Quality Factor and Accelerating Gradient of Nb3Sn-coated Cavity During Pair Assembly

Authors: G. Eremeev, U. Pudasaini, S. Cheban, J. Fischer, D. Forehand, S. Posen, A. Reilly, R. Rimmer, B. Tennis

Abstract: Two CEBAF 5-cell accelerator cavities have been coated with Nb3Sn film using the vapor diffusion technique. One cavity was coated in the Jefferson Lab Nb3Sn cavity coating system, and the other in the Fermilab Nb3Sn coating system. Both cavities were measured at 4 K and 2 K in the vertical dewar test in each lab and then assembled into a cavity pair at Jefferson Lab. Previous attempts to assemble… ▽ More Two CEBAF 5-cell accelerator cavities have been coated with Nb3Sn film using the vapor diffusion technique. One cavity was coated in the Jefferson Lab Nb3Sn cavity coating system, and the other in the Fermilab Nb3Sn coating system. Both cavities were measured at 4 K and 2 K in the vertical dewar test in each lab and then assembled into a cavity pair at Jefferson Lab. Previous attempts to assemble Nb3Sn cavities into a cavity pair degraded the superconducting properties of Nb3Sn-coated cavities. This contribution discusses the efforts to identify and mitigate the pair assembly challenges and will present the results of the vertical tests before and after pair assembly. Notably, one of the cavities reached the highest gradient above 80 mT in the vertical test after the pair assembly. △ Less

Submitted 17 July, 2023; originally announced July 2023.

Comments: 21st Intl Conf Radio Frequency Superconductivity (SRF 2023)

Report number: FERMILAB-CONF-23-341-TD

Commissioning of Dedicated Furnace for Nb3Sn Coatings of 2.6 GHz Single Cell Cavities

Authors: P. A. Kulyavtsev, G. Eremeev, S. Posen, B. Tennis, J. Zasadzinski

Abstract: We present the results of commissioning a dedicated furnace for Nb3Sn coatings of 2.6 GHz single cell cavities. Nb3Sn is a desired coating due to its high critical temperature and smaller surface resistance compared to bulk Nb. Usage of Nb3Sn coated cavities will greatly reduce operating costs due to decreased dependance on cryo cooling. Tin is deposited by use of a tin chloride nucleation agent a… ▽ More We present the results of commissioning a dedicated furnace for Nb3Sn coatings of 2.6 GHz single cell cavities. Nb3Sn is a desired coating due to its high critical temperature and smaller surface resistance compared to bulk Nb. Usage of Nb3Sn coated cavities will greatly reduce operating costs due to decreased dependance on cryo cooling. Tin is deposited by use of a tin chloride nucleation agent and tin vapor diffusion. Analysis of the resultant coating was performed using SEM/EDS to verify successful formation of Nb3Sn. Witness samples in line of sight of the source were used in order to understand the coating efficacy. △ Less

Submitted 17 July, 2023; originally announced July 2023.

Comments: 21st Intl Conf Radio Frequency Superconductivity (SRF 2023)

Report number: FERMILAB-CONF-23-340-TD

Demonstration of Niobium Tin in 218 MHz Low-beta Quarter Wave Accelerator Cavity

Authors: T. B. Petersen, M. P. Kelly, T. Reid, M. Kedzie, B. Guilfoyle, G. Chen, S. Posen, B. Tennis, G. Eremeev

Abstract: A 218 MHz quarter wave niobium cavity has been fabricated for the purpose of demonstrating Nb3Sn technology on a low-beta accelerator cavity. Niobiumtin has been established as a promising next generation SRF material, but development has focused primarily in high-beta elliptical cell cavities. This material has a significantly higher TC than niobium, allowing for design of higher frequency quarte… ▽ More A 218 MHz quarter wave niobium cavity has been fabricated for the purpose of demonstrating Nb3Sn technology on a low-beta accelerator cavity. Niobiumtin has been established as a promising next generation SRF material, but development has focused primarily in high-beta elliptical cell cavities. This material has a significantly higher TC than niobium, allowing for design of higher frequency quarter wave cavities (that are subsequently smaller) as well as for significantly lowered cooling requirements (possibly leading to cryocooler based designs). The fabrication, initial cold testing, and Nb3Sn coating are discussed as well as test plans and details of future applications. △ Less

Submitted 17 July, 2023; originally announced July 2023.

Comments: 21st Intl Conf Radio Frequency Superconductivity (SRF 2023)

Report number: FERMILAB-CONF-23-344-TD

HELEN: Traveling Wave SRF Linear Collider Higgs Factory

Authors: S. Belomestnykh, P. C. Bhat, A. Grassellino, S. Kazakov, H. Padamsee, S. Posen, A. Romanenko, V. Shiltsev, A. Valishev, V. Yakovlev

Abstract: Traveling wave SRF accelerating structures offer several advantages over the traditional standing wave structures: substantially lower $H_pk/E_acc$ and lower $E_pk/E_acc$, ratios of peak magnetic field and peak electric field to the accelerating gradient, respectively, together with substantially higher $R/Q$. In this paper we discuss how a linear collider Higgs Factory HELEN can be built using TW… ▽ More Traveling wave SRF accelerating structures offer several advantages over the traditional standing wave structures: substantially lower $H_pk/E_acc$ and lower $E_pk/E_acc$, ratios of peak magnetic field and peak electric field to the accelerating gradient, respectively, together with substantially higher $R/Q$. In this paper we discuss how a linear collider Higgs Factory HELEN can be built using TW-based SRF linacs. We cover a plan to address technological challenges and describe ways to upgrade the collider luminosity and energy. △ Less

Submitted 12 July, 2023; originally announced July 2023.

Comments: 14th International Particle Accelerator Conference IPAC'23. arXiv admin note: text overlap with arXiv:2209.01074

Report number: FERMILAB-CONF-23-183-AD-PPD-SQMS-TD

Multipacting Processing in Cryomodules For LCLS-II And LCLS-II-HE

Authors: A. Cravatta, T. Arkan, D. Bafia, J. Kaluzny, S. Posen, J. Vennekate, M. Drury, S. Aderhold, M. Checchin, D. Gonnella, J. Hogan, J. Maniscalco, J. Nelson, R. Porter, L. Zacarias

Abstract: Multipacting (MP) is a phenomenon which can affect stability in particle accelerators and limit performance in superconducting radio frequency cavities. In the TESLA shaped, 1.3 GHz, 9-cell cavities used in the LCLS-II (L2) and LCLS-II-HE (HE) projects, the MP-band (~17-24 MV/m) lies within the required accelerating gradients. For HE, the operating gradient of 20.8 MV/m lies well within the MP-ban… ▽ More Multipacting (MP) is a phenomenon which can affect stability in particle accelerators and limit performance in superconducting radio frequency cavities. In the TESLA shaped, 1.3 GHz, 9-cell cavities used in the LCLS-II (L2) and LCLS-II-HE (HE) projects, the MP-band (~17-24 MV/m) lies within the required accelerating gradients. For HE, the operating gradient of 20.8 MV/m lies well within the MP-band and cryomodule testing has confirmed that this is an issue. As such, MP processing for the HE cryomodule test program will be discussed. Early results on MP processing in cryomodules installed in the L2 linac will also be presented, demonstrating that the methods used in cryomodule acceptance testing are also successful at conditioning MP in the accelerator and that this processing is preserved in the mid-term. △ Less

Submitted 29 June, 2023; originally announced June 2023.

Comments: 21st Intl Conf Radio Frequency Superconductivity (SRF 2023)

Report number: FERMILAB-CONF-23-316-TD

Phase-controlled improvement of photon lifetime in coupled superconducting cavities

Authors: Changqing Wang, Oleksandr S Melnychuk, Crispin Contreras-Martinez, Yao Lu, Yuriy M Pischalnikov, Oleg Pronitchev, Bianca Giaccone, Roman Pilipenko, Silvia Zorzetti, Sam Posen, Alexander Romanenko, Anna Grassellino

Abstract: High-quality cavities are crucial for various fundamental physical studies and applications. Here we find that by coupling two cavities directly or via a phase-tunable coupling channel, the photon lifetime of the local field can exceed that of the bare cavities. The cavity photon lifetime is modified by the phases of the initial states and the phase accumulation on the coupling channel which affec… ▽ More High-quality cavities are crucial for various fundamental physical studies and applications. Here we find that by coupling two cavities directly or via a phase-tunable coupling channel, the photon lifetime of the local field can exceed that of the bare cavities. The cavity photon lifetime is modified by the phases of the initial states and the phase accumulation on the coupling channel which affect the interference between cavities. In experiments, by coupling superconducting radio-frequency cavities via phase-tunable cables, we realize a factor of two improvement in the cavity photon lifetime. The results can bring rich revenue to quantum information science, sensing, and high-energy physics. △ Less

Submitted 1 February, 2024; v1 submitted 24 May, 2023; originally announced May 2023.

Comments: 6 pages, 4 figures

Report number: FERMILAB-PUB-23-190-SQMS

Improving Nb3Sn Cavity Performance Using Centrifugal Barrel Polishing

Authors: Eric Viklund, David N. Seidman, David Burk, Sam Posen

Abstract: In this study we will show a new method of polishing for Nb3Sn cavities known as centrifugal barrel polishing (CBP). Using this method, Nb3Sn coated samples are polished to a surface roughness comparable to a traditional Nb cavity after electropolishing (EP). We also investigate different methods of cleaning the Nb3Sn surface after CBP to remove residual abrasive particles. The polished Nb3Sn surf… ▽ More In this study we will show a new method of polishing for Nb3Sn cavities known as centrifugal barrel polishing (CBP). Using this method, Nb3Sn coated samples are polished to a surface roughness comparable to a traditional Nb cavity after electropolishing (EP). We also investigate different methods of cleaning the Nb3Sn surface after CBP to remove residual abrasive particles. The polished Nb3Sn surface is analyzed using confocal laser microscopy, and scanning electron microscopy (SEM) is used to image the surface and measure the surface roughness after polishing. Transmission electron microscopy (TEM) is also used for high resolution analysis of the surface after polishing. Finally, we show that centrifugal barrel polishing can improve the performance of a Nb3Sn SRF cavity. △ Less

Submitted 17 May, 2023; originally announced May 2023.

Report number: FERMILAB-PUB-23-166-TD

Measuring axion gradients with photon interferometry (MAGPI)

Authors: Michael A. Fedderke, Jedidiah O. Thompson, Raphael Cervantes, Bianca Giaccone, Roni Harnik, David E. Kaplan, Sam Posen, Surjeet Rajendran

Abstract: We propose a novel search technique for axions with a $CP$-violating monopole coupling $\tilde{g}_Q$ to bulk Standard Model charges $Q \in \{B,L,B-L\}$. Gradients in the static axion field configurations sourced by matter induce achromatic circular photon birefringence via the axion-photon coupling $g_{φγ}$. Circularly polarized light fed into an optical or (open) radio-frequency (RF) Fabry-Pérot… ▽ More We propose a novel search technique for axions with a $CP$-violating monopole coupling $\tilde{g}_Q$ to bulk Standard Model charges $Q \in \{B,L,B-L\}$. Gradients in the static axion field configurations sourced by matter induce achromatic circular photon birefringence via the axion-photon coupling $g_{φγ}$. Circularly polarized light fed into an optical or (open) radio-frequency (RF) Fabry-Pérot (FP) cavity develops a phase shift that accumulates up to the cavity finesse: the fixed axion spatial gradient prevents a cancellation known to occur for an axion dark-matter search. The relative phase shift between two FP cavities fed with opposite circular polarizations can be detected interferometrically. This time-independent signal can be modulated up to non-zero frequency by altering the cavity orientations with respect to the field gradient. Multi-wavelength co-metrology techniques can be used to address chromatic measurement systematics and noise sources. With Earth as the axion source, we project reach beyond current constraints on the product of couplings $\tilde{g}_Q g_{φγ}$ for axion masses $m_φ \lesssim 10^{-5} \mathrm{eV}$. If shot-noise-limited sensitivity can be achieved, an experiment using high-finesse RF FP cavities could reach a factor of $\sim 10^{5}$ into new parameter space for $\tilde{g}_Q g_{φγ}$ for masses $m_φ\lesssim 4\times 10^{-11} \mathrm{eV}$. △ Less

Submitted 25 January, 2024; v1 submitted 21 April, 2023; originally announced April 2023.

Comments: 9 pages, 2 figures. Published version

Report number: FERMILAB-PUB-23-162-SQMS

Journal ref: Phys. Rev. D 109, 015025 (2024)

Evaluation of predictive correlation between flux expulsion and grain growth for superconducting radio frequency cavities

Authors: Zu Hawn Sung, Paulina Kulyavtsev, Martina Martinello, Dan Gonnella, Marc Ross, Sam Posen

Abstract: A series of experiments were carried out in an effort to develop a simple method for predicting magnetic flux expulsion behavior of high purity niobium used to fabricate superconducting radio frequency (SRF) cavities. Using conventional metallographic characterizations in conjunction with high spatial resolution electron backscattered diffraction-orientation imaging microscopy (EBSD-OIM), we found… ▽ More A series of experiments were carried out in an effort to develop a simple method for predicting magnetic flux expulsion behavior of high purity niobium used to fabricate superconducting radio frequency (SRF) cavities. Using conventional metallographic characterizations in conjunction with high spatial resolution electron backscattered diffraction-orientation imaging microscopy (EBSD-OIM), we found that the flux expulsion behavior of 1.3 GHz single cell SRF Nb cavities is significantly associated with the grain growth of the Nb material during heat treatment. Most of Nb grains rapidly grew during 900C heat treatment, and likely full-recrystallized with 1000C HT. With comparison of the magnetic flux expulsion ratio (Bsc/Bnc) at dT = 5 K, the flux expulsion efficiency of the cavities increases along with increasing of grain size. Most interestingly, 900C HT shows a roughly linear trend that suggests this criterion could be used to predict appropriate heat treatment temperature for sufficient flux expulsion behavior in SRF-grade Nb. This result would be used to see if flux expulsion can be predicted by examining the materials coming from the Nb vendor, prior to cavity fabrication. △ Less

Submitted 24 March, 2023; originally announced March 2023.

New Exclusion Limit for Dark Photons from an SRF Cavity-Based Search (Dark SRF)

Authors: A. Romanenko, R. Harnik, A. Grassellino, R. Pilipenko, Y. Pischalnikov, Z. Liu, O. S. Melnychuk, B. Giaccone, O. Pronitchev, T. Khabiboulline, D. Frolov, S. Posen, A. Berlin, A. Hook

Abstract: We conduct the first ``light-shining-through-wall" (LSW) search for dark photons using two state-of-the-art high quality-factor superconducting radio frequency (SRF) cavities and report the results of its pathfinder run. Our new experimental setup enables improvements in sensitivity over previous searches and covers new dark photon parameter space. We design delicate calibration and measurement pr… ▽ More We conduct the first ``light-shining-through-wall" (LSW) search for dark photons using two state-of-the-art high quality-factor superconducting radio frequency (SRF) cavities and report the results of its pathfinder run. Our new experimental setup enables improvements in sensitivity over previous searches and covers new dark photon parameter space. We design delicate calibration and measurement protocols to utilize the high-$Q$ setup at Dark SRF. Using cavities operating at $1.3 \ \text{GHz}$, we establish a new exclusion limit for kinetic mixing as small as {$ε= 1.6\times 10^{-9}$} and provide the world's best constraints on dark photons in the $2.1\times 10^{-7} \ \text{eV} - 5.7\times10^{-6} \ \text{eV}$ mass range. Our result is the first proof-of-concept for the enabling role of SRF cavities in LSW setups, with ample opportunities for further improvements. In addition, our data sets a competitive lab-based limit on the Standard Model photon mass by searching for longitudinal photon polarization. △ Less

Submitted 26 January, 2023; originally announced January 2023.

HELEN: A Linear Collider Based On Advanced SRF Technology

Authors: S. Belomestnykh, P. C. Bhat, M. Checchin, A. Grassellino, M. Martinello, S. Nagaitsev, H. Padamsee, S. Posen, A. Romanenko, V. Shiltsev, A. Valishev, V. Yakovlev

Abstract: This paper discusses recently proposed Higgs Energy LEptoN (HELEN) $e+e-$ linear collider based on advances in superconducting radio frequency technology. The collider offers cost and AC power savings, smaller footprint (relative to the ILC), and could be built at Fermilab with an interaction region within the site boundaries. After the initial physics run at 250 GeV, the collider could be upgrade… ▽ More This paper discusses recently proposed Higgs Energy LEptoN (HELEN) $e+e-$ linear collider based on advances in superconducting radio frequency technology. The collider offers cost and AC power savings, smaller footprint (relative to the ILC), and could be built at Fermilab with an interaction region within the site boundaries. After the initial physics run at 250 GeV, the collider could be upgraded either to higher luminosity or to higher (up to 500 GeV) energies. △ Less

Submitted 2 September, 2022; originally announced September 2022.

Report number: FERMILAB-CONF-22-643-AD-PPD-SQMS-TD

200 MV Record Voltage Of vCM And LCLS-II-HE Cryomodules Production Start At Fermilab

Authors: T. Arkan, J. Kaluzny, D. Bafia, D. Bice, J. Blowers, A. Cravatta, M. Checchin, B. Giaccone, C. Grimm, B. Hartsell, M. Martinello, T. Nicol, Y. Orlov, S. Posen

Abstract: The Linac Coherent Light Source (LCLS) is an X-ray science facility at SLAC National Accelerator Laboratory. The LCLS-II project (an upgrade to LCLS) is in the commissioning phase; the LCLS-II-HE (High Energy) project is another upgrade to the facility, enabling higher energy operation. An electron beam is accelerated using superconducting radio frequency (SRF) cavities built into cryomodules. It… ▽ More The Linac Coherent Light Source (LCLS) is an X-ray science facility at SLAC National Accelerator Laboratory. The LCLS-II project (an upgrade to LCLS) is in the commissioning phase; the LCLS-II-HE (High Energy) project is another upgrade to the facility, enabling higher energy operation. An electron beam is accelerated using superconducting radio frequency (SRF) cavities built into cryomodules. It is planned to build 24 1.3 GHz standard cryomodules and one 1.3 GHz single-cavity Buncher Capture Cavity (BCC) cryomodule for the LCLS-II-HE project. Fourteen of these standard cryomodules and the BCC are planned to be assembled and tested at Fermilab. Procurements for standard cryomodule components are nearing completion. The first LCLS-II-HE cryomodule, referred to as the verification cryomodule (vCM) was assembled and tested at Fermilab. Fermilab has completed the assembly of the second cryomodule. This paper presents LCLS-II-HE cryomodule production status at Fermilab, emphasizing the changes done based on the successes, challenges, mitigations, and lessons learned from LCLS-II; validation of the changes with the excellent vCM results. △ Less

Submitted 26 August, 2022; originally announced August 2022.

Report number: FERMILAB-CONF-22-623-TD

RF Accelerator Technology R&D: Report of AF7-rf Topical Group to Snowmass 2021

Authors: Sergey Belomestnykh, Emilio A. Nanni, Hans Weise, Sergey V. Baryshev, Pashupati Dhakal, Rongli Geng, Bianca Giaccone, Chunguang Jing, Matthias Liepe, Xueying Lu, Tianhuan Luo, Ganapati Myneni, Alireza Nassiri, David Neuffer, Cho-Kuen Ng, Sam Posen, Sami Tantawi, Anne-Marie Valente-Feliciano, Jean-Luc Vay, Brandon Weatherford, Akira Yamamoto

Abstract: Accelerator radio frequency (RF) technology has been and remains critical for modern high energy physics (HEP) experiments based on particle accelerators. Tremendous progress in advancing this technology has been achieved over the past decade in several areas highlighted in this report. These achievements and new results expected from continued R&D efforts could pave the way for upgrades of existi… ▽ More Accelerator radio frequency (RF) technology has been and remains critical for modern high energy physics (HEP) experiments based on particle accelerators. Tremendous progress in advancing this technology has been achieved over the past decade in several areas highlighted in this report. These achievements and new results expected from continued R&D efforts could pave the way for upgrades of existing facilities, improvements to accelerators already under construction (e.g., PIP-II), well-developed proposals (e.g., ILC, CLIC), and/or enable concepts under development, such as FCC-ee, CEPC, C3, HELEN, multi-MW Fermilab Proton Intensity Upgrade, future Muon Colloder, etc. Advances in RF technology have impact beyond HEP on accelerators built for nuclear physics, basic energy sciences, and other areas. Recent examples of such accelerators are European XFEL, LCLS-II and LCLS-II-HE, SHINE, SNS, ESS, FRIB, and EIC. To support and enable new accelerator-based applications and even make some of them feasible, we must continue addressing their challenges via a comprehensive RF R&D program that would advance the existing RF technologies and explore the nascent ones. △ Less

Submitted 25 August, 2022; originally announced August 2022.

Comments: contribution to Snowmass 2021

An 8 GEV Linac As The Booster Replacement In The Fermilab Power Upgrade

Authors: D. Neuffer, S. Belomestnykh, M. Checchin, D. Johnson, S. Posen, E. Pozdeyev, V. Pronskikh, A. Saini, N. Solyak, V. Yakovlev

Abstract: Increasing the Fermilab Main Injector (MI) beam power above ~1.2 MW requires replacement of the 8 GeV Booster by a higher intensity alternative. Earlier, rapid-cycling synchrotron and linac solutions were considered for this purpose. In this paper, we consider the linac version that produces 8 GeV H- beam for injection into the Recycler Ring (RR) or MI The new linac takes ~1 GeV beam from the PIP-… ▽ More Increasing the Fermilab Main Injector (MI) beam power above ~1.2 MW requires replacement of the 8 GeV Booster by a higher intensity alternative. Earlier, rapid-cycling synchrotron and linac solutions were considered for this purpose. In this paper, we consider the linac version that produces 8 GeV H- beam for injection into the Recycler Ring (RR) or MI The new linac takes ~1 GeV beam from the PIP-II linac and accelerates it to ~ 2 GeV in a 650 MHz SRF linac, and then accelerates to ~8 GeV in an SRF pulsed linac using 1300 MHz cryomodules. The linac components incorporate recent improvements in SRF technology. This Booster Replacement linac (BRL) will increase MI beam power to DUNE to more than 2.5 MW and enable next-generation intensity frontier experiments. △ Less

Submitted 24 August, 2022; originally announced August 2022.

Comments: arXiv admin note: text overlap with arXiv:2203.05052

Report number: FERMILAB-CONF-22-617-AD-TD

Tests Of The Extended Range SRF Cavity Tuners For The LCLS-II-HE Project*

Authors: C. Contreras-Martinez, T. Arkan, A. Cravatta, B. Hartsell, J. Kaluzny, T. Khabiboulline, Y. Pischalnikov, S. Posen, G. Romanov, JC. Yun

Abstract: The LCLS-II HE superconducting linac can produce multi-energy beams by supporting multiple undulator lines simultaneously. This could be achieved by using the cavity SRF tuner in the off-frequency detune mode. This off-frequency operation method was tested in the verification cryomodule (vCM) and CM 1 at Fermilab at 2 K. In both cases, the tuners achieved a frequency shift of -565$\pm$80 kHz. This… ▽ More The LCLS-II HE superconducting linac can produce multi-energy beams by supporting multiple undulator lines simultaneously. This could be achieved by using the cavity SRF tuner in the off-frequency detune mode. This off-frequency operation method was tested in the verification cryomodule (vCM) and CM 1 at Fermilab at 2 K. In both cases, the tuners achieved a frequency shift of -565$\pm$80 kHz. This study will discuss cavity frequency during each step as it is being assembled in the cryomodule string and finally when it is being tested at 2 K. Tracking the cavity frequency helped enable the tuners to reach this large frequency shift. The specific procedures of tuner setting during assembly will be presented. △ Less

Submitted 12 August, 2022; originally announced August 2022.

Report number: FERMILAB-CONF-22-579-TD

LCLS-II and HE Cryomodule Microphonics at CMTF in Fermilab*

Authors: C. Contreras-Martinez, E. Harms, C. Cravatta, J. Holzbauer, S. Posen, L. Doolittle, B. Chase, J. Einstein-Curtis, J. Makara, R. Wang

Abstract: Microphonics causes the cavity to detune. This study discusses the microphonics of sixteen 1.3 GHz cryomodules, 14 for LCLS-II and 2 for LCLS-II HE tested at CMTF. The peak detuning, as well as the RMS detuning for each cryomodule, will be discussed. For each cryomodule, the data was taken with enough soaking time to prevent any thermalization effects which can show up in the detuning. Each data c… ▽ More Microphonics causes the cavity to detune. This study discusses the microphonics of sixteen 1.3 GHz cryomodules, 14 for LCLS-II and 2 for LCLS-II HE tested at CMTF. The peak detuning, as well as the RMS detuning for each cryomodule, will be discussed. For each cryomodule, the data was taken with enough soaking time to prevent any thermalization effects which can show up in the detuning. Each data capture taken was 30 minutes or longer and sampled at 1 kHz. △ Less

Submitted 12 August, 2022; originally announced August 2022.

Report number: FERMILAB-CONF-22-580-TD

Design of axion and axion dark matter searches based on ultra high Q SRF cavities

Authors: Bianca Giaccone, Asher Berlin, Ivan Gonin, Anna Grassellino, Roni Harnik, Yonatan Kahn, Timergali Khabiboulline, Andrei Lunin, Oleksandr Melnychuk, Alexander Netepenko, Roman Pilipenko, Yuriy Pischalnikov, Sam Posen, Oleg Pronitchev, Alex Romanenko, Vyacheslav Yakovlev

Abstract: The Superconducting Quantum Materials and Systems center is developing searches for dark photons, axions and ALPs with the goal of improving upon the current state-of-the-art sensitivity. These efforts leverage on Fermi National Accelerator expertise on ultra-high quality factor superconducting radio frequency cavities combined with the center research on quantum technology. Here we focus on multi… ▽ More The Superconducting Quantum Materials and Systems center is developing searches for dark photons, axions and ALPs with the goal of improving upon the current state-of-the-art sensitivity. These efforts leverage on Fermi National Accelerator expertise on ultra-high quality factor superconducting radio frequency cavities combined with the center research on quantum technology. Here we focus on multiple axion searches that utilize ~1E10 quality factor superconducting radio frequency cavities and their resonant modes to enhance the production and/or detection of axions in the cavity volume. In addition, we present preliminary results of single-mode and multi-mode nonlinearity measurements that were carried out as part of an experimental feasibility study to gain insight on the behavior of the ultra-high quality factor resonators and the experimental RF system in the regime relevant for axion searches. △ Less

Submitted 22 July, 2022; originally announced July 2022.

Comments: 6 pages, 9 figures

Key directions for research and development of superconducting radio frequency cavities

Authors: S. Belomestnykh, S. Posen, D. Bafia, S. Balachandran, M. Bertucci, A. Burrill, A. Cano, M. Checchin, G. Ciovati, L. D. Cooley, G. Dalla Lana Semione, J. Delayen, G. Eremeev, F. Furuta, F. Gerigk, B. Giaccone, D. Gonnella, A. Grassellino, A. Gurevich, W. Hillert, M. Iavarone, J. Knobloch, T. Kubo, W. K. Kwok, R. Laxdal , et al. (31 additional authors not shown)

Abstract: Radio frequency superconductivity is a cornerstone technology for many future HEP particle accelerators and experiments from colliders to proton drivers for neutrino facilities to searches for dark matter. While the performance of superconducting RF (SRF) cavities has improved significantly over the last decades, and the SRF technology has enabled new applications, the proposed HEP facilities and… ▽ More Radio frequency superconductivity is a cornerstone technology for many future HEP particle accelerators and experiments from colliders to proton drivers for neutrino facilities to searches for dark matter. While the performance of superconducting RF (SRF) cavities has improved significantly over the last decades, and the SRF technology has enabled new applications, the proposed HEP facilities and experiments pose new challenges. To address these challenges, the field continues to generate new ideas and there seems to be a vast room for improvements. In this paper we discuss the key research directions that are aligned with and address the future HEP needs. △ Less

Submitted 21 August, 2022; v1 submitted 3 April, 2022; originally announced April 2022.

Comments: contribution to Snowmass 2021

Report number: FERMILAB-PUB-22-241-SQMS-TD

Plasma Processing for In-Situ Field Emission Mitigation of Superconducting Radiofrequency (SRF) Cryomodules

Authors: M. Martinello, P. Berrutti, B. Giaccone, S. Belomestnykh, M. Checchin, G. V. Eremeev, A. Grassellino, T. Khabibouilline, A. Netepenko, R. Pilipenko, A. Romanenko, S. Posen, G. Wu, D. Gonnella, M. Ross, J. T. Maniscalco, T. Powers

Abstract: Field emission (FE) is one of the main limiting factors of superconducting radio-frequency (SRF) cavities operating in accelerators and it occurs whenever contaminants, like dust, metal flakes or even absorbates, are present on the surface of the cavity high electric field region. Field emission reduces the maximum achievable accelerating field and generates free electrons that may interact with t… ▽ More Field emission (FE) is one of the main limiting factors of superconducting radio-frequency (SRF) cavities operating in accelerators and it occurs whenever contaminants, like dust, metal flakes or even absorbates, are present on the surface of the cavity high electric field region. Field emission reduces the maximum achievable accelerating field and generates free electrons that may interact with the beam, damage or activate the beamline. One practical method that can be used to mitigate this problem is in-situ plasma cleaning, or plasma processing. The development of a processing that can be applied in-situ is extremely advantageous, since it enables the recovery of the cryomodule performance without the need of disassembling the whole cryomodule, which is an extremely expensive and time-consuming process. On the other hand, plasma processing only requires the cryomodule warm-up to room-temperature and the subsequent processing of the contaminated cavities. The entire process is reasonably quick and involves a limited number of personnel. For these reasons we would like to advocate for continuing to invest in the R\&D of plasma processing to optimize its applicability in cryomodules and for extending the technique to other frequency ranges and cavities geometries. △ Less

Submitted 23 March, 2022; originally announced March 2022.

Comments: contribution to Snowmass 2021

Higgs-Energy LEptoN (HELEN) Collider based on advanced superconducting radio frequency technology

Authors: S. Belomestnykh, P. C. Bhat, A. Grassellino, M. Checchin, D. Denisov, R. L. Geng, S. Jindariani, M. Liepe, M. Martinello, P. Merkel, S. Nagaitsev, H. Padamsee, S. Posen, R. A. Rimmer, A. Romanenko, V. Shiltsev, A. Valishev, V. Yakovlev

Abstract: This Snowmass 2021 contributed paper discusses a Higgs-Energy LEptoN (HELEN) $e^+e^-$ linear collider based on advances superconducting radio frequency technology. The proposed collider offers cost and AC power savings, smaller footprint (relative to the ILC), and could be built at Fermilab with an Interaction Region within the site boundaries. After the initial physics run at 250 GeV, the collide… ▽ More This Snowmass 2021 contributed paper discusses a Higgs-Energy LEptoN (HELEN) $e^+e^-$ linear collider based on advances superconducting radio frequency technology. The proposed collider offers cost and AC power savings, smaller footprint (relative to the ILC), and could be built at Fermilab with an Interaction Region within the site boundaries. After the initial physics run at 250 GeV, the collider could be upgraded either to higher luminosity or to higher (up to 500 GeV) energies. If the ILC could not be realized in Japan in a timely fashion, the HELEN collider would be a viable option to build a Higgs factory in the U.S. △ Less

Submitted 15 March, 2022; originally announced March 2022.

Comments: contribution to Snowmass 2021

Report number: FERMILAB-FN-1155-AD-PPD-SQMS-TD

Future Collider Options for the US

Authors: P. C. Bhat, S. Jindariani, G. Ambrosio, G. Apollinari, S. Belomestnykh, A. Bross, J. Butler, A. Canepa, D. Elvira, P. Fox, Z. Gecse, E. Gianfelice-Wendt, P. Merkel, S. Nagaitsev, D. Neuffer, H. Piekarz, S. Posen, T. Sen, V. Shiltsev, N. Solyak, D. Stratakis, M. Syphers, G. Velev, V. Yakovlev, K. Yonehara , et al. (1 additional authors not shown)

Abstract: The United States has a rich history in high energy particle accelerators and colliders -- both lepton and hadron machines, which have enabled several major discoveries in elementary particle physics. To ensure continued progress in the field, U.S. leadership as a key partner in building next generation collider facilities abroad is essential; also critically important is the exploring of options… ▽ More The United States has a rich history in high energy particle accelerators and colliders -- both lepton and hadron machines, which have enabled several major discoveries in elementary particle physics. To ensure continued progress in the field, U.S. leadership as a key partner in building next generation collider facilities abroad is essential; also critically important is the exploring of options to host a future collider in the U.S. The "Snowmass" study and the subsequent Particle Physics Project Prioritization Panel (P5) process provide the timely opportunity to develop strategies for both. What we do now will shape the future of our field and whether the U.S. will remain a world leader in these areas. In this white paper, we briefly discuss the US engagement in proposed collider projects abroad and describe future collider options for the U.S. We also call for initiating an integrated R\&D program for future colliders. △ Less

Submitted 15 March, 2022; originally announced March 2022.

Comments: Contribution to Snowmass 2021

Report number: FERMILAB-CONF-22-144-PPD

The International Linear Collider: Report to Snowmass 2021

Authors: Alexander Aryshev, Ties Behnke, Mikael Berggren, James Brau, Nathaniel Craig, Ayres Freitas, Frank Gaede, Spencer Gessner, Stefania Gori, Christophe Grojean, Sven Heinemeyer, Daniel Jeans, Katja Kruger, Benno List, Jenny List, Zhen Liu, Shinichiro Michizono, David W. Miller, Ian Moult, Hitoshi Murayama, Tatsuya Nakada, Emilio Nanni, Mihoko Nojiri, Hasan Padamsee, Maxim Perelstein , et al. (487 additional authors not shown)

Abstract: The International Linear Collider (ILC) is on the table now as a new global energy-frontier accelerator laboratory taking data in the 2030s. The ILC addresses key questions for our current understanding of particle physics. It is based on a proven accelerator technology. Its experiments will challenge the Standard Model of particle physics and will provide a new window to look beyond it. This docu… ▽ More The International Linear Collider (ILC) is on the table now as a new global energy-frontier accelerator laboratory taking data in the 2030s. The ILC addresses key questions for our current understanding of particle physics. It is based on a proven accelerator technology. Its experiments will challenge the Standard Model of particle physics and will provide a new window to look beyond it. This document brings the story of the ILC up to date, emphasizing its strong physics motivation, its readiness for construction, and the opportunity it presents to the US and the global particle physics community. △ Less

Submitted 16 January, 2023; v1 submitted 14 March, 2022; originally announced March 2022.

Comments: 356 pages, Large pdf file (40 MB) submitted to Snowmass 2021; v2 references to Snowmass contributions added, additional authors; v3 references added, some updates, additional authors

Report number: DESY-22-045, IFT--UAM/CSIC--22-028, KEK Preprint 2021-61, PNNL-SA-160884, SLAC-PUB-17662

Nb3Sn Superconducting Radiofrequency Cavities: a Maturing Technology for Particle Accelerators and Detectors

Authors: S. Posen, M. Liepe, G. Eremeev, U. Pudasaini, C. E. Reece

Abstract: Nb3Sn superconducting radiofrequency (SRF) cavities have substantial potential for enabling new performance capabilities for particle accelerators for high energy physics (HEP), as well as for RF cavity-based detectors for dark matter, gravitational waves, and other quantum sensing applications. Outside of HEP, Nb3Sn SRF cavities can also benefit accelerators for nuclear physics, basic energy scie… ▽ More Nb3Sn superconducting radiofrequency (SRF) cavities have substantial potential for enabling new performance capabilities for particle accelerators for high energy physics (HEP), as well as for RF cavity-based detectors for dark matter, gravitational waves, and other quantum sensing applications. Outside of HEP, Nb3Sn SRF cavities can also benefit accelerators for nuclear physics, basic energy sciences, and the industry. In this contribution to Snowmass 2021, we overview the potential, status, and outlook of Nb3Sn SRF cavities. △ Less

Submitted 13 March, 2022; originally announced March 2022.

Comments: contribution to Snowmass 2021

An 8 GeV Linac as the Booster Replacement in the Fermilab Power Upgrade: a Snowmass 2021 White Paper

Authors: S. Belomestnykh, M. Checchin, D. Johnson, D. Neuffer, H. Padamsee, S. Posen, E. Pozdeyev, V. Pronskikh, A. Saini, N. Solyak, V. Yakovlev

Abstract: Following the PIP-II 800 MeV Linac, Fermilab will need an accelerator that extends from that linac to the MI injection energy of ~8 GeV, completing the modernization of the Fermilab high-intensity accelerator complex. This will maximize the beam available for neutrino production for the long baseline DUNE experiment to greater than 2.5 MW and enable a next generation of intensity frontier experime… ▽ More Following the PIP-II 800 MeV Linac, Fermilab will need an accelerator that extends from that linac to the MI injection energy of ~8 GeV, completing the modernization of the Fermilab high-intensity accelerator complex. This will maximize the beam available for neutrino production for the long baseline DUNE experiment to greater than 2.5 MW and enable a next generation of intensity frontier experiments. In this white paper, we propose an 8 GeV Linac for that purpose. The Linac consists of an extension of the PIP-II Linac to ~2 GeV using PIP-II 650 MHz SRF cryomodules, followed by a 2 -->8.0 GeV Linac composed of 1300 MHz SRF cryomodules, based upon the LCLS-II cryomodules developed at Fermilab. The 8 GeV Linac will incorporate recent improvements in SRF technology. The research needed to implement this Linac is described. △ Less

Submitted 2 June, 2023; v1 submitted 9 March, 2022; originally announced March 2022.

Comments: contribution to Snowmass 2021

Measurement of high quality factor superconducting cavities in tesla-scale magnetic fields for dark matter searches

Authors: S. Posen, M. Checchin, O. S. Melnychuk, T. Ring, I. Gonin, T. Khabiboulline

Abstract: In dark matter searches using axion haloscopes, the search sensitivity depends on the quality factors ($Q_0$) of radiofrequency cavities immersed in multi-tesla magnetic fields. Increasing $Q_0$ would increase the scan rate through the parameter space of interest. Researchers developing superconducting radiofrequency cavities for particle accelerators have developed methods for obtaining extremely… ▽ More In dark matter searches using axion haloscopes, the search sensitivity depends on the quality factors ($Q_0$) of radiofrequency cavities immersed in multi-tesla magnetic fields. Increasing $Q_0$ would increase the scan rate through the parameter space of interest. Researchers developing superconducting radiofrequency cavities for particle accelerators have developed methods for obtaining extremely high $Q_0\sim10^{11}$ in $μ$T-scale magnetic fields. In this paper, we describe efforts to develop high Q cavities made from Nb$_3$Sn films using a technique developed for particle accelerator cavities. Geometry optimization for this application is explored, and two cavities are tested: an existing particle accelerator-style cavity and a geometry developed and fabricated for use in high fields. A quality factor of ($5.3\pm0.3$)$\times 10^5$ is obtained at 3.9~GHz and 6~T at 4.2~K. △ Less

Submitted 15 November, 2022; v1 submitted 25 January, 2022; originally announced January 2022.

Plasma Cleaning of LCLS-II-HE verification cryomodule cavities

Authors: Bianca Giaccone, Paolo Berrutti, Martina Martinello, Sam Posen, Andrew Cravatta, Alexandr Netepenko, Tug Arkan, Anna Grassellino, Brian Hartsell, Joshua Kaluzny, Andrew Penhollow, Dan Gonnella, Marc Ross, James Maniscalco, Joel Fuerst, Greg Hays, Marc Doleans

Abstract: Plasma cleaning is a technique that can be applied in superconducting radio-frequency (SRF) cavities in situ in cryomodules in order to decrease their level of field emission. We developed the technique for the Linac Coherent Light Source II (LCLS-II) cavities and we present in this paper the full development and application of plasma processing to the LCLS-II High Energy (HE) verification cryomod… ▽ More Plasma cleaning is a technique that can be applied in superconducting radio-frequency (SRF) cavities in situ in cryomodules in order to decrease their level of field emission. We developed the technique for the Linac Coherent Light Source II (LCLS-II) cavities and we present in this paper the full development and application of plasma processing to the LCLS-II High Energy (HE) verification cryomodule (vCM). We validated our plasma processing procedure on the vCM, fully processing four out of eight cavities of this CM, demonstrating that cavities performance were preserved in terms of both accelerating field and quality factor. Applying plasma processing to this clean, record breaking cryomodule also showed that no contaminants were introduced in the string, maintaining the vCM field emission-free up to the maximum field reached by each cavity. We also found that plasma processing eliminates multipacting (MP) induced quenches that are typically observed frequently within the MP band field range. This suggests that plasma processing could be employed in situ in CMs to mitigate both field emission and multipacting, significantly decreasing the testing time of cryomodules, the linac commissioning time and cost and increasing the accelerator reliability. △ Less

Submitted 1 June, 2022; v1 submitted 24 January, 2022; originally announced January 2022.

Comments: 11 pages, 10 figures

LCLS-II-HE verification cryomodule high gradient performance and quench behavior

Authors: S. Posen, A. Cravatta, M. Checchin, S. Aderhold, C. Adolphsen, T. Arkan, D. Bafia, A. Benwell, D. Bice, B. Chase, C. Contreras-Martinez, L. Dootlittle, J. Fuerst, D. Gonnella, A. Grassellino, C. Grimm, B. Hansen, E. Harms, B. Hartsell, G. Hays, J. Holzbauer, S. Hoobler, J. Kaluzny, T. Khabiboulline, M. Kucera , et al. (21 additional authors not shown)

Abstract: An 8-cavity, 1.3 GHz, LCLS-II-HE cryomodule was assembled and tested at Fermilab to verify performance before the start of production. Its cavities were processed with a novel nitrogen doping treatment to improve gradient performance. The cryomodule was tested with a modified protocol to process sporadic quenches, which were observed in LCLS-II production cryomodules and are attributed to multipac… ▽ More An 8-cavity, 1.3 GHz, LCLS-II-HE cryomodule was assembled and tested at Fermilab to verify performance before the start of production. Its cavities were processed with a novel nitrogen doping treatment to improve gradient performance. The cryomodule was tested with a modified protocol to process sporadic quenches, which were observed in LCLS-II production cryomodules and are attributed to multipacting. Dedicated vertical test experiments support the attribution to multipacting. The verification cryomodule achieved an acceleration voltage of 200 MV in continuous wave mode, corresponding to an average accelerating gradient of 24.1 MV/m, significantly exceeding the specification of 173 MV. The average Q0 (3.0x10^10) also exceeded its specification (2.7x10^10). After processing, no field emission was observed up to the maximum gradient of each cavity. This paper reviews the cryomodule performance and discusses operational issues and mitigations implemented during the several month program. △ Less

Submitted 27 October, 2021; originally announced October 2021.

Comments: 15 pages, 24 figures

Development of a cryocooler conduction-cooled 650 MHz SRF cavity operating at ~10 MV/m cw accelerating gradient

Authors: R. C. Dhuley, S. Posen, M. I. Geelhoed, J. C. T. Thangaraj

Abstract: SRF cavities for particle acceleration are conventionally operated immersed in a bath of liquid helium at 4.2 K and below. Although this cooling configuration is practically and economically viable for large scientific accelerator installations, it may not be so for smaller accelerators intended for industrial applications such as the treatment of wastewater, sludge, flue gases, etc. In this paper… ▽ More SRF cavities for particle acceleration are conventionally operated immersed in a bath of liquid helium at 4.2 K and below. Although this cooling configuration is practically and economically viable for large scientific accelerator installations, it may not be so for smaller accelerators intended for industrial applications such as the treatment of wastewater, sludge, flue gases, etc. In this paper, we describe a procedure to operate SRF cavities without liquid helium that can be used to construct electron-beam sources for industrial applications of electron irradiation (1-10 MeV electron energy). In this procedure, an elliptical single-cell 650 MHz niobium-tin coated niobium cavity is coupled to a closed-cycle 4 K cryocooler using high purity aluminum thermal links. The cryocooler conductively extracts heat (RF dissipation) from the cavity without requiring liquid helium around the cavity. We present construction details of this cryocooler conduction-cooling technique and systematic experiments that have demonstrated ~10 MV/m cw gradient on the cavity. By straightforward scaling up the cavity length and number of cryocoolers, the technique will provide the complete range of 1-10 MeV electron energy for industrial applications. △ Less

Submitted 20 August, 2021; originally announced August 2021.

Advances in Nb3Sn superconducting radiofrequency cavities towards first practical accelerator applications

Authors: S. Posen, J. Lee, D. N. Seidman, A. Romanenko, B. Tennis, O. S. Melnychuk, D. A. Sergatskov

Abstract: Nb3Sn is a promising next-generation material for superconducting radiofrequency cavities, with significant potential for both large scale and compact accelerator applications. However, so far, Nb3Sn cavities have been limited to cw accelerating fields <18 MV/m. In this paper, new results are presented with significantly higher fields, as high as 24 MV/m in single cell cavities. Results are also p… ▽ More Nb3Sn is a promising next-generation material for superconducting radiofrequency cavities, with significant potential for both large scale and compact accelerator applications. However, so far, Nb3Sn cavities have been limited to cw accelerating fields <18 MV/m. In this paper, new results are presented with significantly higher fields, as high as 24 MV/m in single cell cavities. Results are also presented from the first ever Nb3Sn-coated 1.3 GHz 9-cell cavity, a full-scale demonstration on the cavity type used in production for the European XFEL and LCLS-II. Results are presented together with heat dissipation curves to emphasize the potential for industrial accelerator applications using cryocooler-based cooling systems. The cavities studied have an atypical shiny visual appearance, and microscopy studies of witness samples reveal significantly reduced surface roughness and smaller film thickness compared to typical Nb3Sn films for superconducting cavities. Possible mechanisms for increased maximum field are discussed as well as implications for physics of RF superconductivity in the low coherence length regime. Outlook for continued development is presented. △ Less

Submitted 11 August, 2020; v1 submitted 2 August, 2020; originally announced August 2020.

Development and Understanding of Nb$_3$Sn films for radiofrequency applications through a sample-host 9-cell cavity

Authors: T. Spina, B. M. Tennis, J. Lee, D. N. Seidman, S. Posen

Abstract: Nb$_3$Sn is a promising advanced material under development for superconducting radiofrequency (SRF) cavities. Past efforts have been focused primarily on small development-scale cavities, but large, often multi-celled cavities, are needed for particle accelerator applications. In this work, we report on successful Nb$_3$Sn coatings on Nb in a 1 m-long 9-cell Nb sample-host cavity at Fermilab. The… ▽ More Nb$_3$Sn is a promising advanced material under development for superconducting radiofrequency (SRF) cavities. Past efforts have been focused primarily on small development-scale cavities, but large, often multi-celled cavities, are needed for particle accelerator applications. In this work, we report on successful Nb$_3$Sn coatings on Nb in a 1 m-long 9-cell Nb sample-host cavity at Fermilab. The geometry of the first coating with only one Sn source made it possible to study the influence of Sn flux on the microstructure. Based on these results, we postulate a connection between recently observed anomalously large thin grains and uncovered niobium spots observed in the past by other authors [Trenikhina 2018]. A phenomenological model to explain how these anomalously large grains could form is proposed. This model is invoked to provide possible explanations for literature results from several groups and to guide key process parameters to achieve uniform vapor-diffusion coatings, when applied to complex structures as the multi-cell cavity under study. △ Less

Submitted 23 June, 2020; originally announced June 2020.

Analysis of Magnetic Vortex Dissipation in Sn-Segregated Boundaries in Nb$_3$Sn Superconducting RF Cavities

Authors: Jared Carlson, Alden Pack, Mark K. Transtrum, Jaeyel Lee, David N. Seidman, Danilo B. Liarte, Nathan Sitaraman, Alen Senanian, Michelle Kelley, James P. Sethna, Tomas Arias, Sam Posen

Abstract: We study mechanisms of vortex nucleation in Nb$_3$Sn Superconducting RF (SRF) cavities using a combination of experimental, theoretical, and computational methods. Scanning transmission electron microscopy (STEM) image and energy dispersive spectroscopy (EDS) of some Nb$_3$Sn cavities show Sn segregation at grain boundaries in Nb$_3$Sn with Sn concentration as high as $\sim$35 at.\% and widths… ▽ More We study mechanisms of vortex nucleation in Nb$_3$Sn Superconducting RF (SRF) cavities using a combination of experimental, theoretical, and computational methods. Scanning transmission electron microscopy (STEM) image and energy dispersive spectroscopy (EDS) of some Nb$_3$Sn cavities show Sn segregation at grain boundaries in Nb$_3$Sn with Sn concentration as high as $\sim$35 at.\% and widths $\sim$3 nm in chemical composition. Using ab initio calculations, we estimate the effect excess tin has on the local superconducting properties of the material. We model Sn segregation as a lowering of the local critical temperature. We then use time-dependent Ginzburg-Landau theory to understand the role of segregation on magnetic vortex nucleation. Our simulations indicate that the grain boundaries act as both nucleation sites for vortex penetration and pinning sites for vortices after nucleation. Depending on the magnitude of the applied field, vortices may remain pinned in the grain boundary or penetrate the grain itself. We estimate the superconducting losses due to vortices filling grain boundaries and compare with observed performance degradation with higher magnetic fields. We estimate that the quality factor may decrease by an order of magnitude ($10^{10}$ to $10^9$) at typical operating fields if 0.03\% of the grain boundaries actively nucleate vortices. We additionally estimate the volume that would need to be filled with vortices to match experimental observations of cavity heating. △ Less

Submitted 20 December, 2020; v1 submitted 6 March, 2020; originally announced March 2020.

Journal ref: Phys. Rev. B 103, 024516 (2021)

First demonstration of a cryocooler conduction cooled superconducting radiofrequency cavity operating at practical cw accelerating gradients

Authors: R. C. Dhuley, S. Posen, M. I. Geelhoed, O. Prokofiev, J. C. T. Thangaraj

Abstract: We demonstrate practical accelerating gradients on a superconducting radiofrequency (SRF) accelerator cavity with cryocooler conduction cooling, a cooling technique that does not involve the complexities of the conventional liquid helium bath. A design is first presented that enables conduction cooling an elliptical-cell SRF cavity. Implementing this design, a single cell 650 MHz Nb3Sn cavity coup… ▽ More We demonstrate practical accelerating gradients on a superconducting radiofrequency (SRF) accelerator cavity with cryocooler conduction cooling, a cooling technique that does not involve the complexities of the conventional liquid helium bath. A design is first presented that enables conduction cooling an elliptical-cell SRF cavity. Implementing this design, a single cell 650 MHz Nb3Sn cavity coupled using high purity aluminum thermal links to a 4 K pulse tube cryocooler generated accelerating gradients up to 6.6 MV/m at 100% duty cycle. The experiments were carried out with the cavity-cryocooler assembly in a simple vacuum vessel, completely free of circulating liquid cryogens. We anticipate that this cryocooling technique will make the SRF technology accessible to interested accelerator researchers who lack access to full-stack helium cryogenic systems. Furthermore, the technique can lead to SRF based compact sources of high average power electron beams for environmental protection and industrial applications. A concept of such an SRF compact accelerator is presented. △ Less

Submitted 8 July, 2020; v1 submitted 21 January, 2020; originally announced January 2020.

Report number: FERMILAB-PUB-20-011-DI-LDRD-TD

Journal ref: Supercond. Sci. Technol. 33 06LT01 (2020)

Impact of high Q on ILC250 upgrade for record luminosities and path toward ILC380

Authors: H. Padamsee, A. Grassellino, S. Belomestnykh, S. Posen

Abstract: In this paper, we address the possibility of upgrading the ILC250 luminosity to $8.1 \times 10^{34}$, so that with the polarization feature, the effective luminosity will be $2.0 \times 10^{35}$ to compete with the FCC-ee luminosity and two detectors. The additional cost of the higher luminosity option will be about 2.2 B ILCU. The total cost for the ILC high luminosity machine will therefore be a… ▽ More In this paper, we address the possibility of upgrading the ILC250 luminosity to $8.1 \times 10^{34}$, so that with the polarization feature, the effective luminosity will be $2.0 \times 10^{35}$ to compete with the FCC-ee luminosity and two detectors. The additional cost of the higher luminosity option will be about 2.2 B ILCU. The total cost for the ILC high luminosity machine will therefore be about 7.7 B versus FCC-ee 10.5 B. The AC power (267 MW) to operate the ILC luminosity upgrade will also be less than the AC power for FCC-ee (300 MW). Even with a modest quality factor Q of $1 \times 10^{10}$ for SRF cavities, the total cost of the upgrade will be 2.5 B ILCU additional over ILC250 baseline. We expect that, if approved, ILC250 will first be built at the baseline luminosity, operated for many years at this luminosity, and later upgraded to the high luminosity option. A significant part (RF power and cryo-power) of the additional cost for the luminosity upgrade overlaps with the expected additional costs for anticipated energy upgrade paths. A second ILC upgrade discussed in this paper will be to the higher energy Top Factory at 380 GeV. We also estimate the additional cost of this upgrade (1.5 B ILCU). △ Less

Submitted 2 October, 2019; originally announced October 2019.

Ultra-Low Surface Resistance via Vacuum Heat Treatment of Superconducting Radiofrequency Cavities

Authors: S. Posen, A. Romanenko, A. Grassellino, O. S. Melnychuk, D. A. Sergatskov

Abstract: We report on an effort to improve the performance of superconducting radiofrequency cavities by the use of heat treatment in a temperature range sufficient to dissociate the natural surface oxide. We find that the residual resistance is significantly decreased, and we find an unexpected reduction in the BCS resistance. Together these result in extremely high quality factor values at relatively lar… ▽ More We report on an effort to improve the performance of superconducting radiofrequency cavities by the use of heat treatment in a temperature range sufficient to dissociate the natural surface oxide. We find that the residual resistance is significantly decreased, and we find an unexpected reduction in the BCS resistance. Together these result in extremely high quality factor values at relatively large accelerating fields Eacc ~20 MV/m: Q0 of 3-4x10^11 at <1.5 K and Q0 ~5x10^10 at 2.0 K. In one cavity, measurements of surface resistance versus temperature showed an extremely small residual resistance of just 0.63+/-0.06 nOhms at 16 MV/m. SIMS measurements confirm that the oxide was significantly dissociated, but they also show the presence of nitrogen after heat treatment. We also present studies of surface oxidation via exposure to air and to water, as well as the effects of very light surface removal via HF rinse. The possibilities for applications and the planned future development are discussed. △ Less

Submitted 29 June, 2019; originally announced July 2019.

Comments: 9 pages, 9 figures

Journal ref: Phys. Rev. Applied 13, 014024 (2020)

The Role of Magnetic Flux Expulsion to Reach Q0>3x10^10 in SRF Cryomodules

Authors: S. Posen, G. Wu, E. Harms, A. Grassellino, O. S. Melnychuk, D. A. Sergatskov, N. Solyak, A. Palczewski, D. Gonnella, T. Peterson

Abstract: When a superconducting radiofrequency cavity is cooled through its critical temperature, ambient magnetic flux can become "frozen in" to the superconductor, resulting in degradation of the quality factor. This is especially problematic in applications where quality factor is a cost driver, such as in the CW linac for LCLS-II. Previously, it had been unknown how to prevent flux from being trapped d… ▽ More When a superconducting radiofrequency cavity is cooled through its critical temperature, ambient magnetic flux can become "frozen in" to the superconductor, resulting in degradation of the quality factor. This is especially problematic in applications where quality factor is a cost driver, such as in the CW linac for LCLS-II. Previously, it had been unknown how to prevent flux from being trapped during cooldown in bulk niobium cavities, but recent R&D studies showed near-full flux expulsion can be achieved through high temperature heat treatment and cooling cavities through the superconducting transition with a spatial thermal gradient over the surface. In this paper, we describe the first accelerator implementation of these procedures, in cryomodules that are currently being produced for LCLS-II. We compare the performance of cavities under different conditions of heat treatment and thermal gradient during cooldown, showing a substantial improvement in performance when both are applied, enabling cryomodules to reach and, in many cases, exceed a Q0 of ~3x10^10. △ Less

Submitted 10 December, 2018; originally announced December 2018.

Comments: 11 pages

Journal ref: Phys. Rev. Accel. Beams 22, 032001 (2019)

Critical Fields of Nb$_3$Sn Prepared for Superconducting Cavities

Authors: S. Keckert, T. Junginger, T. Buck, D. Hall, P. Kolb, O. Kugeler, R. Laxdal, M. Liepe, S. Posen, T. Prokscha, Z. Salman, A. Suter, J. Knobloch

Abstract: Nb$_3$Sn is currently the most promising material other than niobium for future superconducting radiofrequency cavities. Critical fields above 120 mT in pulsed operation and about 80 mT in CW have been achieved in cavity tests. This is large compared to the lower critical field as derived from the London penetration depth, extracted from low field surface impedance measurements. In this paper dire… ▽ More Nb$_3$Sn is currently the most promising material other than niobium for future superconducting radiofrequency cavities. Critical fields above 120 mT in pulsed operation and about 80 mT in CW have been achieved in cavity tests. This is large compared to the lower critical field as derived from the London penetration depth, extracted from low field surface impedance measurements. In this paper direct measurements of the London penetration depth from which the lower critical field and the superheating field are derived are presented. The field of first vortex penetration is measured under DC and RF fields. The combined results confirm that Nb$_3$Sn cavities are indeed operated in a metastable state above the lower critical field but are currently limited to a critical field well below the superheating field. △ Less

Submitted 16 April, 2019; v1 submitted 31 October, 2018; originally announced October 2018.

Journal ref: Supercond. Sci. Technol. 32 075004, 2019

Three-dimensional superconducting resonators at $T < 20$ mK with the photon lifetime up to $τ=2$ seconds

Authors: A. Romanenko, R. Pilipenko, S. Zorzetti, D. Frolov, M. Awida, S. Belomestnykh, S. Posen, A. Grassellino

Abstract: Very high quality factor superconducting radio frequency cavities developed for accelerators can enable fundamental physics searches with orders of magnitude higher sensitivity, as well as offer a path to a 1000-fold increase in the achievable coherence times for cavity-stored quantum states in the 3D circuit QED architecture. Here we report the first measurements of multiple accelerator cavities… ▽ More Very high quality factor superconducting radio frequency cavities developed for accelerators can enable fundamental physics searches with orders of magnitude higher sensitivity, as well as offer a path to a 1000-fold increase in the achievable coherence times for cavity-stored quantum states in the 3D circuit QED architecture. Here we report the first measurements of multiple accelerator cavities of $f_0=$1.3, 2.6, 5 GHz resonant frequencies down to temperatures of about 10~mK and field levels down to a few photons, which reveal record high photon lifetimes up to 2 seconds, while also further exposing the role of the two level systems (TLS) in the niobium oxide. We also demonstrate how the TLS contribution can be greatly suppressed by the vacuum heat treatments at 340-450$^\circ$C. △ Less

Submitted 23 December, 2019; v1 submitted 8 October, 2018; originally announced October 2018.

Comments: revised version

Journal ref: Phys. Rev. Applied 13, 034032 (2020)

Atomic scale analysis of Nb3Sn on Nb prepared by a vapor-diffusion process for superconducting radiofrequency cavity applications

Authors: Jaeyel Lee, Sam Posen, Zugang Mao, Yulia Trenikhina, Kai He, Daniel L Hall, Matthias Liepe, David N Seidman

Abstract: We report an atomic-scale analysis of the microstructure of Nb3Sn coating on Nb prepared by vapor diffusion process for superconducting radiofrequency (SRF) cavity application using transmission electron microscopy (TEM). Epitaxial growth of Nb3Sn on the Nb substrate is found and four types of orientation relationships at the Nb3Sn/Nb interface are identified by electron diffraction or high-resolu… ▽ More We report an atomic-scale analysis of the microstructure of Nb3Sn coating on Nb prepared by vapor diffusion process for superconducting radiofrequency (SRF) cavity application using transmission electron microscopy (TEM). Epitaxial growth of Nb3Sn on the Nb substrate is found and four types of orientation relationships at the Nb3Sn/Nb interface are identified by electron diffraction or high-resolution scanning transmission electron microscopy (STEM) analysis. Thin Nb3Sn grains are observed in regions with low Sn flux and they have the specific orientation relationship, Nb3Sn (1-20)//Nb (-111) and Nb3Sn (002)//Nb (0-11). The Nb3Sn/Nb interface of thin grains had a large lattice mismatch, 12.3 at.%, and a high density of misfit dislocations was observed by HR-STEM. Based on our microstructural analysis of the thin grains, we conclude that the thin regions are probably a result of a slow interfacial reaction with this particular orientation relationship at the interface. The Sn-deficient regions are seen to form initially at the Nb3Sn/Nb interface and remain in the grains due to the slow diffusion of Sn in bulk Nb3Sn. The formation of Sn-deficient regions and the effects of strain and interfacial energies on the formation of Sn-deficient regions at various interfaces were also estimated by first-principle calculation. The finding of orientation relationships at the Nb3Sn/Nb interface provides important information about the formation of defects in Nb3Sn coatings such as large thin regions, Sn-deficient regions, which are critical to the performance of Nb3Sn superconducting radiofrequency cavities for accelerators. △ Less

Submitted 30 June, 2019; v1 submitted 10 July, 2018; originally announced July 2018.

Journal ref: Supercond. Sci. Technol. 32 (2019) 024001

Accelerating fields up to 49 MV/m in TESLA-shape superconducting RF niobium cavities via 75C vacuum bake

Authors: A. Grassellino, A. Romanenko, D. Bice, O. Melnychuk, A. C. Crawford, S. Chandrasekaran, Z. Sung, D. A. Sergatskov, M. Checchin, S. Posen, M. Martinello, G. Wu

Abstract: In this paper we present the discovery of a new surface treatment applied to superconducting radio frequency (SRF) niobium cavities, leading to unprecedented accelerating fields of 49 MV/m in TESLA-shaped cavities, in continuous wave (CW); the corresponding peak magnetic fields are the highest ever measured in CW, about 210 mT. For TESLA-shape cavities the maximum quench field ever achieved was ~4… ▽ More In this paper we present the discovery of a new surface treatment applied to superconducting radio frequency (SRF) niobium cavities, leading to unprecedented accelerating fields of 49 MV/m in TESLA-shaped cavities, in continuous wave (CW); the corresponding peak magnetic fields are the highest ever measured in CW, about 210 mT. For TESLA-shape cavities the maximum quench field ever achieved was ~45 MV/m - reached very rarely- with most typical values being below 40 MV/m. These values are reached for niobium surfaces treated with electropolishing followed by the so called mild bake, a 120C vacuum bake (for 48 hours for fine grain and 24 hours for large grain surfaces). We discover that the addition during the mild bake of a step at 75C for few hours, before the 120C, increases systematically the quench fields up to unprecedented values of 49 MV/m. The significance of the result lays not only in the relative improvement, but in the proof that niobium surfaces can sustain and exceed CW radio frequency magnetic fields much larger than Hc1, pointing to an extrinsic nature of the current field limitations, and therefore to the potential to reach accelerating fields well beyond the current state of the art. △ Less

Submitted 26 June, 2018; originally announced June 2018.

The Effect of Mechanical Cold Work on the Magnetic Flux Expulsion of Niobium

Authors: S. Posen, S. K. Chandrasekaran, A. C. Crawford, A. Grassellino, O. Melnychuk, A. Romanenko, D. Sergatskov, Y. Trenikhina

Abstract: Expulsion of ambient flux has been shown to be crucial to obtain high quality factors in bulk niobium SRF cavities. However, there remain many questions as to what properties of the niobium material determine its flux expulsion behavior. In this paper, we present first results from a new study of two cavities that were specially fabricated to study flux expulsion. Both cavities were made from larg… ▽ More Expulsion of ambient flux has been shown to be crucial to obtain high quality factors in bulk niobium SRF cavities. However, there remain many questions as to what properties of the niobium material determine its flux expulsion behavior. In this paper, we present first results from a new study of two cavities that were specially fabricated to study flux expulsion. Both cavities were made from large grain ingot niobium slices, one of which had its slices rolled prior to fabrication, and none these slices were annealed prior to measurement. Expulsion measurements indicate that a dense network of grain boundaries is not necessary for a cavity to have near-complete flux trapping behavior up to large thermal gradients. The results also contribute to a body of evidence that cold work is a strong determinant of flux expulsion behavior in SRF-grade niobium. △ Less

Submitted 19 April, 2018; originally announced April 2018.

Comments: 7 pages, 10 figures

Frequency dependence of trapped flux sensitivity in SRF cavities

Authors: Mattia Checchin, Martina Martinello, Anna Grassellino, Sebastian Aderhold, Saravan K. Chandrasekaran, Oleksandr Melnychuk, Sam Posen, Alexander Romanenko, Dmitri A. Sergatskov

Abstract: In this letter, we present the frequency dependence of the vortex surface resistance of bulk niobium accelerating cavities as a function of different state-of-the-art surface treatments. Higher flux surface resistance per amount of trapped magnetic field - sensitivity - is observed for higher frequencies, in agreement with our theoretical model. Higher sensitivity is observed for N-doped cavities,… ▽ More In this letter, we present the frequency dependence of the vortex surface resistance of bulk niobium accelerating cavities as a function of different state-of-the-art surface treatments. Higher flux surface resistance per amount of trapped magnetic field - sensitivity - is observed for higher frequencies, in agreement with our theoretical model. Higher sensitivity is observed for N-doped cavities, which possess an intermediate value of electron mean-free-path, compared to 120 C and EP/BCP cavities. Experimental results from our study showed that the sensitivity has a non-monotonic trend as a function of the mean-free-path, including at frequencies other than 1.3 GHz, and that the vortex response to the rf field can be tuned from the pinning regime to flux-flow regime by manipulating the frequency and/or the mean-free-path of the resonator, as reported in our previous studies. The frequency dependence of the trapped flux sensitivity to the amplitude of the accelerating gradient is also highlighted. △ Less

Submitted 15 November, 2017; originally announced November 2017.

Advancement in the understanding of the field and frequency dependent microwave surface resistance of niobium

Authors: M. Martinello, S. Aderhold, S. K. Chandrasekaran, M. Checchin, A. Grassellino, O. Melnychuk, S. Posen, A. Romanenko, D. A. Sergatskov

Abstract: The radio-frequency surface resistance of niobium resonators is incredibly reduced when nitrogen impurities are dissolved as interstitial in the material, conferring ultra-high Q-factors at medium values of accelerating field. This effect has been observed in both high and low temperature nitrogen treatments. As a matter of fact, the peculiar anti Q-slope observed in nitrogen doped cavities, i.e.… ▽ More The radio-frequency surface resistance of niobium resonators is incredibly reduced when nitrogen impurities are dissolved as interstitial in the material, conferring ultra-high Q-factors at medium values of accelerating field. This effect has been observed in both high and low temperature nitrogen treatments. As a matter of fact, the peculiar anti Q-slope observed in nitrogen doped cavities, i.e. the decreasing of the Q-factor with the increasing of the radio-frequency field, come from the decreasing of the BCS surface resistance component as a function of the field. Such peculiar behavior has been considered consequence of the interstitial nitrogen present in the niobium lattice after the doping treatment. The study here presented show the field dependence of the BCS surface resistance of cavities with different resonant frequencies, such as: 650 MHz, 1.3 GHz, 2.6 GHz and 3.9 GHz, and processed with different state-of-the-art surface treatments. These findings show for the first time that the anti Q-slope might be seen at high frequency even for clean Niobium cavities, revealing useful suggestion on the physics underneath the anti Q-slope effect. △ Less

Submitted 24 July, 2017; originally announced July 2017.

Comments: To be published in Proceedings of SRF 2017

Performance-defining properties of Nb$_3$Sn coating in SRF cavities

Authors: Y. Trenikhina, S. Posen, A. Romanenko, M. Sardela, J. -M. Zuo, D. L. Hall, M. Liepe

Abstract: Nb$_3$Sn has great potential to become the material of choice for fabrication of SRF cavities. The higher critical temperature of Nb$_3$Sn potentially allows for an increased operational temperature in SRF cavities, which could enable tremendous simplification of cryogenic system, leading to significant cost reduction. We present extended characterization of a Nb$_3$Sn coated Nb cavity prepared at… ▽ More Nb$_3$Sn has great potential to become the material of choice for fabrication of SRF cavities. The higher critical temperature of Nb$_3$Sn potentially allows for an increased operational temperature in SRF cavities, which could enable tremendous simplification of cryogenic system, leading to significant cost reduction. We present extended characterization of a Nb$_3$Sn coated Nb cavity prepared at Cornell University. Using combination of thermometry during cavity RF measurements, and structural and analytical characterization of the cavity cutouts, we discover Nb$_3$Sn coating flaws responsible for the poor cavity performance. Our results clearly show degraded material quality in the cavity cutouts which exhibit significant heating during the RF testing. Results of extended comparison of cavity cutouts with different dissipation profiles not only point out the cause of significant Q-slope but also establish figures of merit for material qualities in relation to the quality of SRF performance. △ Less

Submitted 18 July, 2017; originally announced July 2017.