-
Untrapped HOM Radiation Absorption in the LCLS-II Cryomodules
Authors:
K. Bane,
C. Nantista,
C. Adolphsen,
T. Raubenheimer,
A. Saini,
N. Solyak,
V. Yakovlev
Abstract:
The superconducting cavities in the continuous wave (CW) linacs of LCLS-II are designed to operate at 2 K, where cooling costs are very expensive. One source of heat is presented by the higher order mode (HOM) power deposited by the beam. Due to the very short bunch length--especially in L3 the final linac--the LCLS-II beam spectrum extends into the terahertz range. Ceramic absorbers, at 70 K and…
▽ More
The superconducting cavities in the continuous wave (CW) linacs of LCLS-II are designed to operate at 2 K, where cooling costs are very expensive. One source of heat is presented by the higher order mode (HOM) power deposited by the beam. Due to the very short bunch length--especially in L3 the final linac--the LCLS-II beam spectrum extends into the terahertz range. Ceramic absorbers, at 70 K and located between cryomodules, are meant to absorb much of this power. In this report we perform two kinds of calculations to estimate the effectiveness of the absorbers and the amount of beam power that needs to be removed at 2 K.
△ Less
Submitted 5 November, 2014;
originally announced November 2014.
-
The International Linear Collider Technical Design Report - Volume 3.I: Accelerator R&D in the Technical Design Phase
Authors:
Chris Adolphsen,
Maura Barone,
Barry Barish,
Karsten Buesser,
Philip Burrows,
John Carwardine,
Jeffrey Clark,
Hélène Mainaud Durand,
Gerry Dugan,
Eckhard Elsen,
Atsushi Enomoto,
Brian Foster,
Shigeki Fukuda,
Wei Gai,
Martin Gastal,
Rongli Geng,
Camille Ginsburg,
Susanna Guiducci,
Mike Harrison,
Hitoshi Hayano,
Keith Kershaw,
Kiyoshi Kubo,
Victor Kuchler,
Benno List,
Wanming Liu
, et al. (19 additional authors not shown)
Abstract:
The International Linear Collider Technical Design Report (TDR) describes in four volumes the physics case and the design of a 500 GeV centre-of-mass energy linear electron-positron collider based on superconducting radio-frequency technology using Niobium cavities as the accelerating structures. The accelerator can be extended to 1 TeV and also run as a Higgs factory at around 250 GeV and on the…
▽ More
The International Linear Collider Technical Design Report (TDR) describes in four volumes the physics case and the design of a 500 GeV centre-of-mass energy linear electron-positron collider based on superconducting radio-frequency technology using Niobium cavities as the accelerating structures. The accelerator can be extended to 1 TeV and also run as a Higgs factory at around 250 GeV and on the Z0 pole. A comprehensive value estimate of the accelerator is give, together with associated uncertainties. It is shown that no significant technical issues remain to be solved. Once a site is selected and the necessary site-dependent engineering is carried out, construction can begin immediately. The TDR also gives baseline documentation for two high-performance detectors that can share the ILC luminosity by being moved into and out of the beam line in a "push-pull" configuration. These detectors, ILD and SiD, are described in detail. They form the basis for a world-class experimental programme that promises to increase significantly our understanding of the fundamental processes that govern the evolution of the Universe.
△ Less
Submitted 26 June, 2013;
originally announced June 2013.
-
The International Linear Collider Technical Design Report - Volume 3.II: Accelerator Baseline Design
Authors:
Chris Adolphsen,
Maura Barone,
Barry Barish,
Karsten Buesser,
Philip Burrows,
John Carwardine,
Jeffrey Clark,
Hélène Mainaud Durand,
Gerry Dugan,
Eckhard Elsen,
Atsushi Enomoto,
Brian Foster,
Shigeki Fukuda,
Wei Gai,
Martin Gastal,
Rongli Geng,
Camille Ginsburg,
Susanna Guiducci,
Mike Harrison,
Hitoshi Hayano,
Keith Kershaw,
Kiyoshi Kubo,
Victor Kuchler,
Benno List,
Wanming Liu
, et al. (19 additional authors not shown)
Abstract:
The International Linear Collider Technical Design Report (TDR) describes in four volumes the physics case and the design of a 500 GeV centre-of-mass energy linear electron-positron collider based on superconducting radio-frequency technology using Niobium cavities as the accelerating structures. The accelerator can be extended to 1 TeV and also run as a Higgs factory at around 250 GeV and on the…
▽ More
The International Linear Collider Technical Design Report (TDR) describes in four volumes the physics case and the design of a 500 GeV centre-of-mass energy linear electron-positron collider based on superconducting radio-frequency technology using Niobium cavities as the accelerating structures. The accelerator can be extended to 1 TeV and also run as a Higgs factory at around 250 GeV and on the Z0 pole. A comprehensive value estimate of the accelerator is give, together with associated uncertainties. It is shown that no significant technical issues remain to be solved. Once a site is selected and the necessary site-dependent engineering is carried out, construction can begin immediately. The TDR also gives baseline documentation for two high-performance detectors that can share the ILC luminosity by being moved into and out of the beam line in a "push-pull" configuration. These detectors, ILD and SiD, are described in detail. They form the basis for a world-class experimental programme that promises to increase significantly our understanding of the fundamental processes that govern the evolution of the Universe.
△ Less
Submitted 26 June, 2013;
originally announced June 2013.
-
A Resonant Cavity for Single-Shot Emittance Measurement
Authors:
J. S. Kim,
C. D. Nantista,
D. H. Whittum,
R. H. Miller,
S. G. Tantawi,
A. W. Weidemann
Abstract:
We present a non-invasive, resonant cavity based approach to beam emittance measurement of a shot-to-shot non-circular beam pulse of multi-bunches. In a resonant cavity, desired field components can be enhanced up to Q_L_lambda/pi, where Q_L_lambda is the loaded Q of the resonance mode lambda, when the cavity resonant mode matches with the beam operating frequency. In particular, a Quad-cavity,…
▽ More
We present a non-invasive, resonant cavity based approach to beam emittance measurement of a shot-to-shot non-circular beam pulse of multi-bunches. In a resonant cavity, desired field components can be enhanced up to Q_L_lambda/pi, where Q_L_lambda is the loaded Q of the resonance mode lambda, when the cavity resonant mode matches with the beam operating frequency. In particular, a Quad-cavity, with its quadrupole mode at beam operating frequency, extracts the beam quad-moment exclusively, utilizing the symmetry of the cavity and some simple networks to suppress common modes. Six successive beam quadrupole moment measurements, performed at different betatron phases in a linear transport system, allow us to determine the beam emittance, i.e., the beam size and shape in the beam's phase space. One measurement alone provides the rms-beam size if the beam position is given, for instance, by nearby beam-position-monitors. This paper describes the basic design and analysis of a Quad-cavity beam monitoring system.
△ Less
Submitted 18 September, 2002;
originally announced September 2002.
-
A Multi-Moded RF Delay Line Distribution System for the Next Linear Collider
Authors:
S. G. Tantawi,
C. Nantista,
N. Kroll,
Z. Li,
R. Miller,
R. Ruth,
P. Wilson,
J. Neilson
Abstract:
The Delay Line Distribution System (DLDS) is an alternative to conventional pulse compression, which enhances the peak power of rf sources while matching the long pulse of those sources to the shorter filling time of accelerator structures. We present an implementation of this scheme that combines pairs of parallel delay lines of the system into single lines. The power of several sources is comb…
▽ More
The Delay Line Distribution System (DLDS) is an alternative to conventional pulse compression, which enhances the peak power of rf sources while matching the long pulse of those sources to the shorter filling time of accelerator structures. We present an implementation of this scheme that combines pairs of parallel delay lines of the system into single lines. The power of several sources is combined into a single waveguide delay line using a multi-mode launcher. The output mode of the launcher is determined by the phase coding of the input signals. The combined power is extracted from the delay line using mode-selective extractors, each of which extracts a single mode. Hence, the phase coding of the sources controls the output port of the combined power. The power is then fed to the local accelerator structures. We present a detailed design of such a system, including several implementation methods for the launchers, extractors, and ancillary high power rf components. The system is designed so that it can handle the 600 MW peak power required by the NLC design while maintaining high efficiency.
△ Less
Submitted 17 September, 2002;
originally announced September 2002.
-
A Compact, Planar, Eight-Port Waveguide Power Divider/Combiner: The Cross Potent Superhybrid
Authors:
Christopher D. Nantista,
Sami G. Tantawi
Abstract:
In this letter, we present a novel four-way divider/combiner in rectangular waveguide. The design is completely two-dimensional in the h-plane, with eight-fold mirror symmetry, and is based on a recent four-port hybrid design [6]. In combining mode, it can function as a phased array with four inputs and four outputs. The planar nature of this design provides advantages, such as the freedom to in…
▽ More
In this letter, we present a novel four-way divider/combiner in rectangular waveguide. The design is completely two-dimensional in the h-plane, with eight-fold mirror symmetry, and is based on a recent four-port hybrid design [6]. In combining mode, it can function as a phased array with four inputs and four outputs. The planar nature of this design provides advantages, such as the freedom to increase the waveguide height beyond the over-moding limit in order to reduce field strengths. Along with its open geometry, this makes it ideal for high-power applications where rf break down is a concern. Design criteria, field-solver simulation results, and prototype measurements are presented.
△ Less
Submitted 12 February, 2001;
originally announced February 2001.
-
Planar Waveguide Hybrids for Very High Power RF
Authors:
C. D. Nantista,
W. R. Fowkes,
N. M. Kroll,
S. G. Tantawi
Abstract:
Two basic designs have been developed for waveguide hybrids, or 3-dB couplers, capable of handling hundreds of megawatts at X-band. Coupling is provided by one or two connecting waveguides with h-plane junctions and matching elements. In the former case, the connecting waveguide supports two modes. Small apertures and field-enhancing e-bends are avoided to reduce the risk of rf breakdown. The h-…
▽ More
Two basic designs have been developed for waveguide hybrids, or 3-dB couplers, capable of handling hundreds of megawatts at X-band. Coupling is provided by one or two connecting waveguides with h-plane junctions and matching elements. In the former case, the connecting waveguide supports two modes. Small apertures and field-enhancing e-bends are avoided to reduce the risk of rf breakdown. The h-plane symmetry also allows the use of over-moded rectangular waveguide in which the height has been increased to reduce field amplitudes without affecting the scattering matrix. The theory and designs are presented, along with the results of prototype tests of functionality and power-handling capability. Such a device is integral to the rf pulse compression or power distribution system of the Next Linear Collider (NLC) for combining, splitting, and directing power. This work was motivated by the observation of rf breakdown at power levels above 200 MW in conventional and modified magic-T's.
△ Less
Submitted 12 February, 2001;
originally announced February 2001.
-
Beam Profile Monitors in the Nlcta
Authors:
C. Nantista,
C. Adolphsen,
R. L. Brown,
R. Fuller,
J. Rifkin
Abstract:
The transverse current profile in the Next Linear Collider Test Accelerator (NLCTA) electron beam can be monitored at several locations along the beam line by means of profile monitors. These consist of insertable phosphor screens, light collection and transport systems, CID cameras, a frame-grabber, and PC and VAX based image analysis software. In addition to their usefulness in tuning and stee…
▽ More
The transverse current profile in the Next Linear Collider Test Accelerator (NLCTA) electron beam can be monitored at several locations along the beam line by means of profile monitors. These consist of insertable phosphor screens, light collection and transport systems, CID cameras, a frame-grabber, and PC and VAX based image analysis software. In addition to their usefulness in tuning and steering the accelerator, the profile monitors are utilized for emittance measurement. A description of these systems and their performance is presented.
△ Less
Submitted 7 July, 2000;
originally announced July 2000.
-
Beam Current Monitors in the Nlcta
Authors:
Christopher Nantista,
Chris Adolphsen
Abstract:
The current profile along the 126 ns, multi-bunch beam pulse in the Next Linear Collider Test Accelerator (NLCTA) is monitored with fast toroids (rise time ~1 ns). Inserted at several positions along the beam line, they allow us to track current transmission as a function of position along the bunch train. Various measurements, such as rise time, current, width, and slope, are made on the digiti…
▽ More
The current profile along the 126 ns, multi-bunch beam pulse in the Next Linear Collider Test Accelerator (NLCTA) is monitored with fast toroids (rise time ~1 ns). Inserted at several positions along the beam line, they allow us to track current transmission as a function of position along the bunch train. Various measurements, such as rise time, current, width, and slope, are made on the digitized signals, which can be corrected in software by means of stored frequency response files. The design and implementation of these devices is described.
△ Less
Submitted 6 July, 2000;
originally announced July 2000.
