Showing 1–23 of 23 results for author: Konno, T

PMT calibration for the JSNS2-II far detector with an embedded LED system

Authors: Jisu Park, M. K. Cheoun, J. H. Choi, J. Y. Choi, T. Dodo, J. Goh, M. Harada, S. Hasegawa, W. Hwang, T. Iida, H. I. Jang, J. S. Jang, K. K. Joo, D. E. Jung, S. K. Kang, Y. Kasugai, T. Kawasaki, E. M. Kim, S. B. Kim, S. Y. Kim, H. Kinoshita, T. Konno, D. H. Lee, C. Little, T. Maruyama , et al. (31 additional authors not shown)

Abstract: The JSNS2-II (the second phase of JSNS2, J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) is an experiment aimed at searching for sterile neutrinos. This experiment has entered its second phase, employing two liquid scintillator detectors located at near and far positions from the neutrino source. Recently, the far detector of the experiment has been completed and is currently i… ▽ More The JSNS2-II (the second phase of JSNS2, J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) is an experiment aimed at searching for sterile neutrinos. This experiment has entered its second phase, employing two liquid scintillator detectors located at near and far positions from the neutrino source. Recently, the far detector of the experiment has been completed and is currently in the calibration phase. This paper presents a detailed description of the calibration process utilizing the LED system. The LED system of the far detector uses two Ultra-Violet (UV) LEDs, which are effective in calibrating all of PMTs at once. The UV light is converted into the visible light wavelengths inside liquid scintillator via the wavelength shifters, providing pseudo-isotropic light. The properties of all functioning Photo-Multiplier-Tubes (PMTs) to detect the neutrino events in the far detector, such as gain, its dependence of supplied High Voltage (HV), and Peak-to-Valley (PV) were calibrated. To achieve a good energy resolution for physics events, up to 10% of the relative gain adjustment is required for all functioning PMTs. This will be achieved using the measured HV curves and the LED calibration. The Peak-to-Valley (PV) ratio values are the similar to those from the production company, which distinguish the single photo-electron signal from the pedestal. Additionally, the precision of PMT signal timing is measured to be 2.1 ns, meeting the event reconstruction requirement of 10 ns. △ Less

Submitted 11 March, 2025; originally announced March 2025.

Muon tagging with Flash ADC waveform baselines

Authors: D. H. Lee, M. K. Cheoun, J. H. Choi, J. Y. Choi, T. Dodo, J. Goh, M. Harada, S. Hasegawa, W. Hwang, T. Iida, H. I. Jang, J. S. Jang, K. K. Joo, D. E. Jung, S. K. Kang, Y. Kasugai, T. Kawasaki, E. M. Kim, E. J. Kim, S. B. Kim, S. Y. Kim, H. Kinoshita, T. Konno, C. Little, T. Maruyama , et al. (32 additional authors not shown)

Abstract: This manuscript describes an innovative method to tag the muons using the baseline information of the Flash ADC (FADC) waveform of PMTs in the JSNS1 (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) experiment. This experiment is designed for the search for sterile neutrinos, and a muon tagging is an essential key component for the background rejection since the detector of the… ▽ More This manuscript describes an innovative method to tag the muons using the baseline information of the Flash ADC (FADC) waveform of PMTs in the JSNS1 (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) experiment. This experiment is designed for the search for sterile neutrinos, and a muon tagging is an essential key component for the background rejection since the detector of the experiment is located over-ground, where is the 3rd floor of the J-PARC Material and Life experimental facility (MLF). Especially, stopping muons inside the detector create the Michel electrons, and they are important background to be rejected. Utilizing this innovative method, more than 99.8% of Michel electrons can be rejected even without a detector veto region. This technique can be employed for any experiments which uses the similar detector configurations. △ Less

Submitted 2 September, 2025; v1 submitted 22 February, 2025; originally announced February 2025.

Comments: 8 pages, 8 figures

Evaluation of the performance of the event reconstruction algorithms in the JSNS$^2$ experiment using a $^{252}$Cf calibration source

Authors: D. H. Lee, M. K. Cheoun, J. H. Choi, J. Y. Choi, T. Dodo, J. Goh, K. Haga, M. Harada, S. Hasegawa, W. Hwang, T. Iida, H. I. Jang, J. S. Jang, K. K. Joo, D. E. Jung, S. K. Kang, Y. Kasugai, T. Kawasaki, E. J. Kim, J. Y. Kim, S. B Kim, W. Kim, H. Kinoshita, T. Konno, I. T. Lim , et al. (28 additional authors not shown)

Abstract: JSNS$^2$ searches for short baseline neutrino oscillations with a baseline of 24~meters and a target of 17~tonnes of the Gd-loaded liquid scintillator. The correct algorithm on the event reconstruction of events, which determines the position and energy of neutrino interactions in the detector, are essential for the physics analysis of the data from the experiment. Therefore, the performance of th… ▽ More JSNS$^2$ searches for short baseline neutrino oscillations with a baseline of 24~meters and a target of 17~tonnes of the Gd-loaded liquid scintillator. The correct algorithm on the event reconstruction of events, which determines the position and energy of neutrino interactions in the detector, are essential for the physics analysis of the data from the experiment. Therefore, the performance of the event reconstruction is carefully checked with calibrations using $^{252}$Cf source. This manuscript describes the methodology and the performance of the event reconstruction. △ Less

Submitted 19 January, 2025; v1 submitted 5 April, 2024; originally announced April 2024.

Journal ref: Nucl. Inst. Meth. A 1072 (2025) 170216

Pulse Shape Discrimination in JSNS$^2$

Authors: T. Dodo, M. K. Cheoun, J. H. Choi, J. Y. Choi, J. Goh, K. Haga, M. Harada, S. Hasegawa, W. Hwang, T. Iida, H. I. Jang, J. S. Jang, K. K. Joo, D. E. Jung, S. K. Kang, Y. Kasugai, T. Kawasaki, E. J. Kim, J. Y. Kim, S. B. Kim, W. Kim, H. Kinoshita, T. Konno, D. H. Lee, I. T. Lim , et al. (29 additional authors not shown)

Abstract: JSNS$^2$ (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) is an experiment that is searching for sterile neutrinos via the observation of $\barν_μ \rightarrow \barν_e$ appearance oscillations using neutrinos with muon decay-at-rest. For this search, rejecting cosmic-ray-induced neutron events by Pulse Shape Discrimination (PSD) is essential because the JSNS$^2$ detector is loca… ▽ More JSNS$^2$ (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) is an experiment that is searching for sterile neutrinos via the observation of $\barν_μ \rightarrow \barν_e$ appearance oscillations using neutrinos with muon decay-at-rest. For this search, rejecting cosmic-ray-induced neutron events by Pulse Shape Discrimination (PSD) is essential because the JSNS$^2$ detector is located above ground, on the third floor of the building. We have achieved 95$\%$ rejection of neutron events while keeping 90$\%$ of signal, electron-like events using a data driven likelihood method. △ Less

Submitted 22 February, 2025; v1 submitted 28 March, 2024; originally announced April 2024.

Comments: arXiv admin note: text overlap with arXiv:2111.07482, arXiv:2308.02722

Journal ref: PTEP 2025 023H02 (2025)

The acrylic vessel for JSNS$^{2}$-II neutrino target

Authors: C. D. Shin, S. Ajimura, M. K. Cheoun, J. H. Choi, J. Y. Choi, T. Dodo, J. Goh, K. Haga, M. Harada, S. Hasegawa, T. Hiraiwa, W. Hwang, T. Iida, H. I. Jang, J. S. Jang, H. Jeon, S. Jeon, K. K. Joo, D. E. Jung, S. K. Kang, Y. Kasugai, T. Kawasaki, E. J. Kim, J. Y. Kim, S. B. Kim , et al. (35 additional authors not shown)

Abstract: The JSNS$^{2}$ (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) is an experiment designed for the search for sterile neutrinos. The experiment is currently at the stage of the second phase named JSNS$^{2}$-II with two detectors at near and far locations from the neutrino source. One of the key components of the experiment is an acrylic vessel, that is used for the target volume… ▽ More The JSNS$^{2}$ (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) is an experiment designed for the search for sterile neutrinos. The experiment is currently at the stage of the second phase named JSNS$^{2}$-II with two detectors at near and far locations from the neutrino source. One of the key components of the experiment is an acrylic vessel, that is used for the target volume for the detection of the anti-neutrinos. The specifications, design, and measured properties of the acrylic vessel are described. △ Less

Submitted 11 December, 2023; v1 submitted 4 September, 2023; originally announced September 2023.

Journal ref: 2023 JINST 18 T12001

Study on the accidental background of the JSNS$^2$ experiment

Authors: D. H. Lee, S. Ajimura, M. K. Cheoun, J. H. Choi, J. Y. Choi, T. Dodo, J. Goh, K. Haga, M. Harada, S. Hasegawa, T. Hiraiwa, W. Hwang, H. I. Jang, J. S. Jang, H. Jeon, S. Jeon, K. K. Joo, D. E. Jung, S. K. Kang, Y. Kasugai, T. Kawasaki, E. J. Kim, J. Y. Kim, S. B. Kim, W. Kim , et al. (33 additional authors not shown)

Abstract: JSNS$^2$ (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) is an experiment which searches for sterile neutrinos via the observation of $\barν_μ \to \barν_{e}$ appearance oscillations using muon decay-at-rest neutrinos. The data taking of JSNS$^2$ have been performed from 2021. In this manuscript, a study of the accidental background is presented. The rate of the accidental back… ▽ More JSNS$^2$ (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) is an experiment which searches for sterile neutrinos via the observation of $\barν_μ \to \barν_{e}$ appearance oscillations using muon decay-at-rest neutrinos. The data taking of JSNS$^2$ have been performed from 2021. In this manuscript, a study of the accidental background is presented. The rate of the accidental background is (9.29$\pm 0.39) \times 10^{-8}$ / spill with 0.75 MW beam power and comparable to the number of searching signals. △ Less

Submitted 22 April, 2024; v1 submitted 4 August, 2023; originally announced August 2023.

Comments: arXiv admin note: substantial text overlap with arXiv:2111.07482

Journal ref: Eur. Phys. J. C 84, 409 (2024)

An optical transition-edge sensor with high energy resolution

Authors: Kaori Hattori, Toshio Konno, Yoshitaka Miura, Sachiko Takasu, Daiji Fukuda

Abstract: Optical transition-edge sensors have shown energy resolution for resolving the number of incident photons at the telecommunication wavelength. Higher energy resolution is required for biological imaging and microscope spectroscopy. In this paper, we report on a Au/Ti (10/20 nm) bilayer TES that showed high energy resolution. This was achieved by lowering the critical temperature Tc to 115 mK and t… ▽ More Optical transition-edge sensors have shown energy resolution for resolving the number of incident photons at the telecommunication wavelength. Higher energy resolution is required for biological imaging and microscope spectroscopy. In this paper, we report on a Au/Ti (10/20 nm) bilayer TES that showed high energy resolution. This was achieved by lowering the critical temperature Tc to 115 mK and the resultant energy resolution was 67 meV full width at half maximum (FWHM) at 0.8 eV. When Tc was lowered to 115 mK, the theoretical resolution would scaled up to 30 meV FWHM, considering that the typical energy resolution of optical TESs is 150 meV and Tc is 300 mK. To investigate the gap between the theoretical expectation (30 meV) and the measured value (67 meV), we measured its complex impedance and current noise. We found excess Johnson noise in the TES and an excess Johnson term M was 1.5 at a bias point where the resistance was 10% of normal resistance. For reference, the TES was compared with a TES showing typical energy resolution (156 meV FWHM). We will discuss what improved the energy resolution and what might have been the limiting factor on it. △ Less

Submitted 4 April, 2022; originally announced April 2022.

The Double Chooz antineutrino detectors

Authors: Double Chooz Collaboration, H. de Kerret, Y. Abe, C. Aberle, T. Abrahão, J. M. Ahijado, T. Akiri, J. M. Alarcón, J. Alba, H. Almazan, J. C. dos Anjos, S. Appel, F. Ardellier, I. Barabanov, J. C. Barriere, E. Baussan, A. Baxter, I. Bekman, M. Bergevin, A. Bernstein, W. Bertoli, T. J. C. Bezerra, L. Bezrukov, C. Blanco, N. Bleurvacq , et al. (226 additional authors not shown)

Abstract: This article describes the setup and performance of the near and far detectors in the Double Chooz experiment. The electron antineutrinos of the Chooz nuclear power plant were measured in two identically designed detectors with different average baselines of about 400 m and 1050 m from the two reactor cores. Over many years of data taking the neutrino signals were extracted from interactions in th… ▽ More This article describes the setup and performance of the near and far detectors in the Double Chooz experiment. The electron antineutrinos of the Chooz nuclear power plant were measured in two identically designed detectors with different average baselines of about 400 m and 1050 m from the two reactor cores. Over many years of data taking the neutrino signals were extracted from interactions in the detectors with the goal of measuring a fundamental parameter in the context of neutrino oscillation, the mixing angle θ13. The central part of the Double Chooz detectors was a main detector comprising four cylindrical volumes filled with organic liquids. From the inside towards the outside there were volumes containing gadolinium-loaded scintillator, gadolinium-free scintillator, a buffer oil and, optically separated, another liquid scintillator acting as veto system. Above this main detector an additional outer veto system using plastic scintillator strips was installed. The technologies developed in Double Chooz were inspiration for several other antineutrino detectors in the field. The detector design allowed implementation of efficient background rejection techniques including use of pulse shape information provided by the data acquisition system. The Double Chooz detectors featured remarkable stability, in particular for the detected photons, as well as high radiopurity of the detector components. △ Less

Submitted 13 September, 2022; v1 submitted 31 January, 2022; originally announced January 2022.

Comments: 49 pages, 29 figures

Journal ref: Eur.Phys.J. C (2022) 82:804

The JSNS^2 Detector

Authors: S. Ajimura, M. Botran, J. H. Choi, J. W. Choi, M. K. Cheoun, T. Dodo, H. Furuta, J. Goh, K. Haga, M. Harada, S. Hasegawa, Y. Hino, T. Hiraiwa, H. I. Jang, J. S. Jang, M. C. Jang, H. Jeon, S. Jeon, K. K. Joo, J. R. Jordan, D. E. Jung, S. K. Kang, Y. Kasugai, T. Kawasaki, E. J. Kim , et al. (41 additional authors not shown)

Abstract: The JSNS^2 (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) experiment aims to search for oscillations involving a sterile neutrino in the eV^2 mass-splitting range. The experiment will search for the appearance of electron antineutrinos oscillated from muon antineutrinos. The electron antineutrinos are detected via the inverse beta decay process using a liquid scintillator det… ▽ More The JSNS^2 (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) experiment aims to search for oscillations involving a sterile neutrino in the eV^2 mass-splitting range. The experiment will search for the appearance of electron antineutrinos oscillated from muon antineutrinos. The electron antineutrinos are detected via the inverse beta decay process using a liquid scintillator detector. A 1MW beam of 3 GeV protons incident on a spallation neutron target produces an intense and pulsed neutrino source from pion, muon, and kaon decay at rest. The JSNS^2 detector is located 24 m away from the neutrino source and began operation from June 2020. The detector contains 17 tonnes of gadolinium (Gd) loaded liquid scintillator (LS) in an acrylic vessel, as a neutrino target. It is surrounded by 31 tonnes of unloaded LS in a stainless steel tank. Optical photons produced in LS are viewed by 120 R7081 Hamamatsu 10-inch Photomultiplier Tubes (PMTs). In this paper, we describe the JSNS^2 detector design, construction, and operation. △ Less

Submitted 24 August, 2021; v1 submitted 27 April, 2021; originally announced April 2021.

Comments: 41 pages, 29 figures

The trigger slow control system of the Belle II experiment

Authors: C. -H. Kim, Y. Unno, B. G. Cheon, S. H. Kim, I. S. Lee, T. Koga, Y. -T. Lai, Y. Iwasaki, S. Yamada, M. Nakao, H. Nakazawa, E. -J. Jang, S. -K. Choi, T. Konno, D. Liventsev, S. -H. Park, Y. -J. Kwon, O. Hartbrich, M. Ritzert

Abstract: The Belle II experiment at the SuperKEKB $e^{+}e^{-}$ collider in KEK, Japan, started physics data-taking with a complete detector from early 2019 with the primary physics goal of probing new physics in heavy quark and lepton decays. An online trigger system is indispensable for the Belle II experiment to reduce the beam background events associated with high electron and positron beam currents wi… ▽ More The Belle II experiment at the SuperKEKB $e^{+}e^{-}$ collider in KEK, Japan, started physics data-taking with a complete detector from early 2019 with the primary physics goal of probing new physics in heavy quark and lepton decays. An online trigger system is indispensable for the Belle II experiment to reduce the beam background events associated with high electron and positron beam currents without sacrificing the target physics-oriented events. During the Belle II operation upon beam collision, the trigger system must be consistently controlled and its status must be carefully monitored in the process of data acquisition against unexpected situations. For this purpose, we have developed a slow control system for the Belle II trigger system. Around seventy thousand configuration parameters are saved in the Belle II central database server for every run when a run starts and stops. These parameters play an essential role in offline validation of the quality of runs. Around three thousand real-time variables are stored in the Belle II main archiving server, and the trend of some of these variables are regularly used for online and offline monitoring purposes. Various operator interface tools have been prepared and used. When the configuration parameters are not correctly applied, or some of the processes are unexpectedly terminated, the slow control system detects it, stops the data-taking process, and generates an alarm. In this article, we report how we constructed the Belle II trigger slow control system, and how we successfully managed to operate during its initial stage. △ Less

Submitted 20 January, 2021; v1 submitted 3 November, 2020; originally announced November 2020.

Archiver System Management for Belle II Detector Operation

Authors: Y. -K. Kim, S. -J. Cho, S. -H. Park, M. Nakao, T. Konno

Abstract: The Belle II experiment is a high-energy physics experiment at the SuperKEKB electron-positron collider. Using Belle II data, high precision measurement of rare decays and CP-violation in heavy quarks and leptons can be performed to probe New Physics. In this paper, we present the archiver system used to store the monitoring data of the Belle II detector and discuss in particular how we maintain t… ▽ More The Belle II experiment is a high-energy physics experiment at the SuperKEKB electron-positron collider. Using Belle II data, high precision measurement of rare decays and CP-violation in heavy quarks and leptons can be performed to probe New Physics. In this paper, we present the archiver system used to store the monitoring data of the Belle II detector and discuss in particular how we maintain the system that archives the monitoring process variables of the subdetectors. We currently save about 26 thousand variables including the temperature of various subdetectors components, status of water leak sensors, high voltage power supply status, data acquisition status, and luminosity information of the colliding beams. For stable data taking, it is essential to collect and archive these variables. We ensure the availability and consistency of all the variables from the subdetector and other systems, as well as the status of the archiver itself are consistent and regularly updated. To cope with a possible hardware failure, we prepared a backup archiver that is synchronized with the main archiver. △ Less

Submitted 30 October, 2020; originally announced October 2020.

Comments: This work has been submitted to the IEEE for possible publication

Performance of the Unified Readout System of Belle II

Authors: Mikihiko Nakao, Ryosuke Itoh, Satoru Yamada, Soh Y. Suzuki, Tomoyuki Konno, Qi-Dong Zhou, Takuto Kunigo, Ryohei Sugiura, Seokhee Park, Zhen-An Liu, Jingzhou Zhao, Igor Konorov, Dmytro Levit, Katsuro Nakamura, Hikaru Tanigawa, Nanae Taniguchi, Tomohisa Uchida, Kurtis Nishimura, Oskar Hartbrich, Yun-Tsung Lai, Masayoshi Shoji, Alexander Kuzmin, Vladimir Zhulanov, Brandon Kunkler, Isar Mostafanezhad , et al. (2 additional authors not shown)

Abstract: The Belle II experiment at the SuperKEKB collider at KEK, Tsukuba, Japan has successfully started taking data with the full detector in March 2019. Belle II is a luminosity frontier experiment of the new generation to search for physics beyond the Standard Model of elementary particles, from precision measurements of a huge number of B and charm mesons and tau leptons. In order to read out the eve… ▽ More The Belle II experiment at the SuperKEKB collider at KEK, Tsukuba, Japan has successfully started taking data with the full detector in March 2019. Belle II is a luminosity frontier experiment of the new generation to search for physics beyond the Standard Model of elementary particles, from precision measurements of a huge number of B and charm mesons and tau leptons. In order to read out the events at a high rate from the seven subdetectors of Belle II, we adopt a highly unified readout system, including a unified trigger timing distribution system (TTD), a unified high speed data link system (Belle2link), and a common backend system to receive Belle2link data. Each subdetector frontend readout system has a field-programmable gate array (FPGA) in which unified firmware components of the TTD receiver and Belle2link transmitter are embedded. The system is designed for data taking at a trigger rate up to 30 kHz with a dead-time fraction of about 1% in the frontend readout system. The trigger rate is still much lower than our design. However, the background level is already high due to the initial vacuum condition and other accelerator parameters, and it is the most limiting factor of the accelerator and detector operation. Hence the occupancy and radiation effects to the frontend electronics are rather severe, and they cause various kind of instabilities. We present the performance of the system, including the achieved trigger rate, dead-time fraction, stability, and discuss the experience gained during the operation. △ Less

Submitted 26 May, 2021; v1 submitted 29 October, 2020; originally announced October 2020.

Comments: IEEE Real Time 2020 Conference, 7 pages

Performance evaluation of the aerogel RICH counter for the Belle II spectrometer using early beam collision data

Authors: M. Yonenaga, I. Adachi, L. Burmistrov, F. Le Diberder, T. Iijima, S. Iwata, S. Kakimoto, H. Kakuno, G. Karyan, H. Kawai, T. Kawasaki, H. Kindo, H. Kitamura, M. Kobayashi, T. Kohriki, T. Konno, S. Korpar, P. Križan, T. Kumita, K. Kuze, Y. Lai, M. Mrvar, G. Nazaryan, S. Nishida, M. Nishimura , et al. (10 additional authors not shown)

Abstract: The Aerogel Ring Imaging Cherenkov (ARICH) counter serves as a particle identification device in the forward end-cap region of the Belle II spectrometer. It is capable of identifying pions and kaons with momenta up to $4 \, {\rm GeV}/c$ by detecting Cherenkov photons emitted in the silica aerogel radiator. After the detector alignment and calibration of the probability density function, we evaluat… ▽ More The Aerogel Ring Imaging Cherenkov (ARICH) counter serves as a particle identification device in the forward end-cap region of the Belle II spectrometer. It is capable of identifying pions and kaons with momenta up to $4 \, {\rm GeV}/c$ by detecting Cherenkov photons emitted in the silica aerogel radiator. After the detector alignment and calibration of the probability density function, we evaluate the performance of the ARICH counter using early beam collision data. Event samples of $D^{\ast +} \to D^0 π^+ (D^0 \to K^-π^+)$ were used to determine the $π(K)$ efficiency and the $K(π)$ misidentification probability. We found that the ARICH counter is capable of separating kaons from pions with an identification efficiency of $93.5 \pm 0.6 \, \%$ at a pion misidentification probability of $10.9 \pm 0.9 \, \%$. This paper describes the identification method of the counter and the evaluation of the performance during its early operation. △ Less

Submitted 14 August, 2020; originally announced August 2020.

Comments: To be published in Prog. Theor. Exp. Phys

The JSNS$^{2}$ data acquisition system

Authors: J. S. Park, S. Ajimura, M. Botran, M. K. Cheoun, J. H. Choi, T. Dodo, H. Furuta, P. Gwak, M. Harada, S. Hasegawa, Y. Hino, T. Hiraiwa, H. I. Jang, J. S. Jang, M. Jang, H. Jeon, S. Jeon, K. K. Joo, J. R. Jordan, D. E. Jung, S. K. Kang, Y. Kasugai, T. Kawasaki, E. J. Kim, J. Y. Kim , et al. (36 additional authors not shown)

Abstract: The JSNS$^{2}$ (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) experiment aims to search for neutrino oscillations over a 24 m short baseline at J-PARC. The JSNS$^{2}$ inner detector is filled with 17 tons of gadolinium(Gd)-loaded liquid scintillator (LS) with an additional 31 tons of unloaded LS in the intermediate $γ$-catcher and an optically separated outer veto volumes. A… ▽ More The JSNS$^{2}$ (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) experiment aims to search for neutrino oscillations over a 24 m short baseline at J-PARC. The JSNS$^{2}$ inner detector is filled with 17 tons of gadolinium(Gd)-loaded liquid scintillator (LS) with an additional 31 tons of unloaded LS in the intermediate $γ$-catcher and an optically separated outer veto volumes. A total of 120 10-inch photomultiplier tubes observe the scintillating optical photons and each analog waveform is stored with the flash analog-to-digital converters. We present details of the data acquisition, processing, and data quality monitoring system. We also present two different trigger logics which are developed for the beam and self-trigger. △ Less

Submitted 31 May, 2020; originally announced June 2020.

Comments: 11 pages, 8 figures

Performance of PMTs for the JSNS2 experiment

Authors: J. S. Park, H. Furuta, T. Maruyama, S. Monjushiro, K. Nishikawa, M. Taira, J. S. Jang, K. K. Joo, J. Y. Kim, I. T. Lim, D. H. Moon, J. H. Seo, C. D. Shin, A. Zohaib, P. Gwak, M. Jang, S. Ajimura, T. Hiraiwa, T. Nakano, M. Nomachi, T. Shima, Y. Sugaya, M. K. Cheoun, J. H. Choi, M. Y. Pac , et al. (36 additional authors not shown)

Abstract: The JSNS$^{2}$ (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) experiment aims to search for neutrino oscillations over a 24\,m short baseline at J-PARC. The JSNS$^{2}$ inner detector is filled with 17 tons of gadolinium-loaded liquid scintillator (LS) and both the intermediate $γ$-catcher and the optically separated outer veto are filled with un-loaded LS. Optical photons fro… ▽ More The JSNS$^{2}$ (J-PARC Sterile Neutrino Search at J-PARC Spallation Neutron Source) experiment aims to search for neutrino oscillations over a 24\,m short baseline at J-PARC. The JSNS$^{2}$ inner detector is filled with 17 tons of gadolinium-loaded liquid scintillator (LS) and both the intermediate $γ$-catcher and the optically separated outer veto are filled with un-loaded LS. Optical photons from scintillation are observed by 120 Photomultiplier Tubes (PMTs). A total of 130 PMTs for the JSNS2 experiment were both donated by other experiments and purchased from Hamamatsu. Donated PMTs were purchased around 10 years ago, therefore JSNS$^{2}$ did pre-calibration of the PMTs including the purchased PMTs. 123 PMTs demonstrated acceptable performance for the JSNS$^{2}$ experiment, and 120 PMTs were installed in the detector. △ Less

Submitted 25 May, 2020; v1 submitted 4 May, 2020; originally announced May 2020.

Slow control and monitoring system at the JSNS$^{2}$

Authors: J. S. Park, S. Ajimura, M. Botran, J. H. Choi, J. W. Choi, M. K. Cheoun, T. Dodo, H. Furuta, J. Goh, M. Harada, S. Hasegawa, Y. Hino, T. Hiraiwa, H. I. Jang, J. S. Jang, M. C. Jang, H. Jeon, S. Jeon, K. K. Joo, J. R. Jordan, D. E Jung, S. K. Kang, Y. Kasugai, T. Kawasaki, E. J. Kim , et al. (37 additional authors not shown)

Abstract: The JSNS$^2$ experiment is aimed to search for sterile neutrino oscillations using a neutrino beam from muon decays at rest. The JSNS$^2$ detector contains 17 tons of 0.1\% gadolinium (Gd) loaded liquid scintillator (LS) as a neutrino target. Detector construction was completed in the spring of 2020. A slow control and monitoring system (SCMS) was implemented for reliable control and quick monitor… ▽ More The JSNS$^2$ experiment is aimed to search for sterile neutrino oscillations using a neutrino beam from muon decays at rest. The JSNS$^2$ detector contains 17 tons of 0.1\% gadolinium (Gd) loaded liquid scintillator (LS) as a neutrino target. Detector construction was completed in the spring of 2020. A slow control and monitoring system (SCMS) was implemented for reliable control and quick monitoring of the detector operational status and environmental conditions. It issues an alarm if any of the monitored parameters exceed a preset acceptable range. The SCMS monitors the high voltage (HV) of the photomultiplier tubes (PMTs), the LS level in the detector, possible LS overflow and leakage, the temperature and air pressure in the detector, the humidity of the experimental hall, and the LS flow rate during filling and extraction. An initial 10 days of data-taking with a neutrino beam was done following a successful commissioning of the detector and SCMS in June 2020. In this paper, we present a description of the assembly and installation of the SCMS and its performance. △ Less

Submitted 7 April, 2021; v1 submitted 4 May, 2020; originally announced May 2020.

Comments: 12 pages, 11 figures

Deep Learning Model for Finding New Superconductors

Authors: Tomohiko Konno, Hodaka Kurokawa, Fuyuki Nabeshima, Yuki Sakishita, Ryo Ogawa, Iwao Hosako, Atsutaka Maeda

Abstract: Exploration of new superconductors still relies on the experience and intuition of experts and is largely a process of experimental trial and error. In one study, only 3% of the candidate materials showed superconductivity. Here, we report the first deep learning model for finding new superconductors. We introduced the method named "reading periodic table" which represented the periodic table in a… ▽ More Exploration of new superconductors still relies on the experience and intuition of experts and is largely a process of experimental trial and error. In one study, only 3% of the candidate materials showed superconductivity. Here, we report the first deep learning model for finding new superconductors. We introduced the method named "reading periodic table" which represented the periodic table in a way that allows deep learning to learn to read the periodic table and to learn the law of elements for the purpose of discovering novel superconductors that are outside the training data. It is recognized that it is difficult for deep learning to predict something outside the training data. Although we used only the chemical composition of materials as information, we obtained an $R^{2}$ value of 0.92 for predicting $T_\text{c}$ for materials in a database of superconductors. We also introduced the method named "garbage-in" to create synthetic data of non-superconductors that do not exist. Non-superconductors are not reported, but the data must be required for deep learning to distinguish between superconductors and non-superconductors. We obtained three remarkable results. The deep learning can predict superconductivity for a material with a precision of 62%, which shows the usefulness of the model; it found the recently discovered superconductor CaBi2 and another one Hf0.5Nb0.2V2Zr0.3, neither of which is in the superconductor database; and it found Fe-based high-temperature superconductors (discovered in 2008) from the training data before 2008. These results open the way for the discovery of new high-temperature superconductor families. The candidate materials list, data, and method are openly available from the link https://github.com/tomo835g/Deep-Learning-to-find-Superconductors. △ Less

Submitted 14 January, 2021; v1 submitted 3 December, 2018; originally announced December 2018.

Comments: 10 pages in main text. Deep learning, Machine learning, Material search, Superconductors

Journal ref: Phys. Rev. B 103, 014509 (2021)

Environmental Monitoring for Belle II

Authors: SeokHee Park, Youngjoon Kwon, Mikihiko Nakao, Uehara Sadaharu, Tomoyuki Konno

Abstract: The Belle II experiment has just started, searching for physics beyond the Standard Model in $B$, charm and $τ$ decays using data with the integrated luminosity goal of $50 ~\mathrm{ab}^{-1}$. Before the physics run with full detector system being installed, Belle II Phase 2 run is on-going at the time of the conference, until July 2018. In this presentation, we describe the environmental monitori… ▽ More The Belle II experiment has just started, searching for physics beyond the Standard Model in $B$, charm and $τ$ decays using data with the integrated luminosity goal of $50 ~\mathrm{ab}^{-1}$. Before the physics run with full detector system being installed, Belle II Phase 2 run is on-going at the time of the conference, until July 2018. In this presentation, we describe the environmental monitoring system with an emphasis on the software tools to help the experts and the non-expert shifters who operate the experiment. The monitoring tools are prepared on the control room especially for the shift-takers. It consists of thre components: the monitoring GUI, the alarm system, and the archiver. The monitoring GUI shows the current state of the detector and the alarm system generate warning states from monitored variables with sound and email notification. The archiver is collecting data on single server and provide collected data to the experimental collaborators. △ Less

Submitted 23 June, 2018; originally announced June 2018.

Comments: Poster presentation at 21st IEEE Real Time Conference (RT2018)

Local 3d Electronic Structures of Co-Based Complexes with Medicinal Molecules Probed by Soft X-Ray Absorption

Authors: Kohei Yamagami, Hidenori Fujiwara, Shin Imada, Toshiharu Kadono, Keisuke Yamanaka, Takayuki Muro, Arata Tanaka, Takuma Itai, Nobuto Yoshinari, Takumi Konno, Akira Sekiyama

Abstract: We have examined the local 3d electronic structures of Co-Au multinuclear complexes with the medicinal molecules D-penicillaminate (D-pen) [Co{Au(PPh3)(D-pen)}2]ClO4 and [Co3{Au3(tdme)(D-pen)3}2] by Co L_2,3-edge soft X-ray absorption (XAS) spectroscopy, where PPh3 denotes triphenylphosphine and tdme stands for 1,1,1-tris[(diphenylphosphino)methyl]ethane. The Co L_2,3-edge XAS spectra indicate the… ▽ More We have examined the local 3d electronic structures of Co-Au multinuclear complexes with the medicinal molecules D-penicillaminate (D-pen) [Co{Au(PPh3)(D-pen)}2]ClO4 and [Co3{Au3(tdme)(D-pen)3}2] by Co L_2,3-edge soft X-ray absorption (XAS) spectroscopy, where PPh3 denotes triphenylphosphine and tdme stands for 1,1,1-tris[(diphenylphosphino)methyl]ethane. The Co L_2,3-edge XAS spectra indicate the localized ionic 3d electronic states in both materials. The experimental spectra are well explained by spectral simulation for a localized Co ion under ligand fields with the full multiplet theory, which verifies that the ions are in the low-spin Co3+ state in the former compound and in the high-spin Co2+ state in the latter. △ Less

Submitted 21 May, 2017; v1 submitted 15 March, 2016; originally announced March 2016.

Comments: 7 pages, 5 figures. To be published in J. Phys. Soc. Jpn

Journal ref: J. Phys. Soc. Jpn. 86, 074801 (2017)

Study of the basic performance of the XRPIX for the future astronomical X-ray satellite

Authors: Koki Tamasawa, Takayoshi Kohmura, Takahiro Konno, Takeshi Go Tsuru, Takaaki Tanaka, Ayaki Takeda, Hideaki Matsumura, Koji Mori, Yusuke Nishioka, Ryota Takenaka

Abstract: We have developed CMOS imaging sensor (XRPIX) using SOI (Silicon-On-Insulator) technology for the X-ray astronomical use. XRPIX(X-Ray soiPIXel) has advantage of a high time resolution, a high position resolution and an observation in a wide X-ray energy band with a thick depletion layer of over 200um. However, the energy resolution of XRPIX is not as good as one of X-ray CCD. Therefore improveme… ▽ More We have developed CMOS imaging sensor (XRPIX) using SOI (Silicon-On-Insulator) technology for the X-ray astronomical use. XRPIX(X-Ray soiPIXel) has advantage of a high time resolution, a high position resolution and an observation in a wide X-ray energy band with a thick depletion layer of over 200um. However, the energy resolution of XRPIX is not as good as one of X-ray CCD. Therefore improvement of the the energy resolution is one of the most important development item of XRPIX. In order to evaluate the performance XRPIX more precisely, we have investigated on the temperature dependence of the basic performance, such as readout noise, leak current, gain and energy resolution, using two type of XRPIX, XRPIX1 and XRPIX2b_CZ. In our study, we confirmed the readout noise, the leak current noise and the energy resolution clearly depended on the operating temperature of XRPIX. In addition, we divided the readout noise into the leak current noise and the circuit origin noise. As a result, we found that noise of the electronic circuitry origin was proportional to the square root of operating temperature. △ Less

Submitted 24 July, 2015; originally announced July 2015.

Comments: 11 pages, 13 figures, "Proceedings of International Workshop on SOI Pixel Detector (SOIPIX2015), Tohoku University, Sendai, Japan, 3-6, June, 2015. C15-06-03."

Reactor electron antineutrino disappearance in the Double Chooz experiment

Authors: Y. Abe, C. Aberle, J. C. dos Anjos, J. C. Barriere, M. Bergevin, A. Bernstein, T. J. C. Bezerra, L. Bezrukhov, E. Blucher, N. S. Bowden, C. Buck, J. Busenitz, A. Cabrera, E. Caden, L. Camilleri, R. Carr, M. Cerrada, P. -J. Chang, P. Chimenti, T. Classen, A. P. Collin, E. Conover, J. M. Conrad, J. I. Crespo-Anadón, K. Crum , et al. (140 additional authors not shown)

Abstract: The Double Chooz experiment has observed 8,249 candidate electron antineutrino events in 227.93 live days with 33.71 GW-ton-years (reactor power x detector mass x livetime) exposure using a 10.3 cubic meter fiducial volume detector located at 1050 m from the reactor cores of the Chooz nuclear power plant in France. The expectation in case of theta13 = 0 is 8,937 events. The deficit is interpreted… ▽ More The Double Chooz experiment has observed 8,249 candidate electron antineutrino events in 227.93 live days with 33.71 GW-ton-years (reactor power x detector mass x livetime) exposure using a 10.3 cubic meter fiducial volume detector located at 1050 m from the reactor cores of the Chooz nuclear power plant in France. The expectation in case of theta13 = 0 is 8,937 events. The deficit is interpreted as evidence of electron antineutrino disappearance. From a rate plus spectral shape analysis we find sin^2 2θ13 = 0.109 \pm 0.030(stat) \pm 0.025(syst). The data exclude the no-oscillation hypothesis at 99.8% CL (2.9σ). △ Less

Submitted 30 August, 2012; v1 submitted 26 July, 2012; originally announced July 2012.

Comments: Modified for PRD referees

Journal ref: Phys. Rev. D 86, 052008 (2012)

Development and evaluation of 10-inch Photo-Multiplier Tubes for the Double Chooz experiment

Authors: T. Matsubara, T. Haruna, T. Konno, Y. Endo, M. Bongrand, H. Furuta, T. Hara, M. Ishitsuka, T. Kawasaki, M. Kuze, J. Maeda, Y. Mishina, Y. Miyamoto, H. Miyata, Y. Nagasaka, Y. Sakamoto, F. Sato, A. Shigemori, F. Suekane, T. Sumiyoshi, H. Tabata, N. Tamura

Abstract: The goal of Double Chooz experiment is a precise measurement of the last unknown mixing angle theta_13 using two identical detectors placed at far and near sites from Chooz reactor cores. The detector is optimized for reactor-neutrino detection using specially developed 10-inch PMTs. We developed two types of measurement systems and evaluated 400 PMTs before the installation. Those PMTs fulfill ou… ▽ More The goal of Double Chooz experiment is a precise measurement of the last unknown mixing angle theta_13 using two identical detectors placed at far and near sites from Chooz reactor cores. The detector is optimized for reactor-neutrino detection using specially developed 10-inch PMTs. We developed two types of measurement systems and evaluated 400 PMTs before the installation. Those PMTs fulfill our requirements, and a half of those have been installed to the far detector in 2009. The character and performance data of the PMTs are stored in a database and will be referenced in analysis and MC simulation. △ Less

Submitted 5 April, 2011; originally announced April 2011.

Comments: Submitted to Nuclear Instruments and Methods A

A Condition for Cooperation in a Game on Complex Networks

Authors: Tomohiko Konno

Abstract: We study a condition of favoring cooperation in a Prisoner's Dilemma game on complex networks. There are two kinds of players: cooperators and defectors. Cooperators pay a benefit b to their neighbors at a cost c, whereas defectors only receive a benefit. The game is a death-birth process with weak selection. Although it has been widely thought that b/c> <k> is a condition of favoring cooperation,… ▽ More We study a condition of favoring cooperation in a Prisoner's Dilemma game on complex networks. There are two kinds of players: cooperators and defectors. Cooperators pay a benefit b to their neighbors at a cost c, whereas defectors only receive a benefit. The game is a death-birth process with weak selection. Although it has been widely thought that b/c> <k> is a condition of favoring cooperation, we find that b/c> <knn> is the condition. We also show that among three representative networks, namely, regular, random, and scale-free, a regular network favors cooperation the most, whereas a scale-free network favors cooperation the least. In an ideal scale-free network where network size is infinite, cooperation is never realized. Whether or not the scale-free network and network heterogeneity favor cooperation depends on the details of a game, although it is occasionally believed that scale-free networks favor cooperation irrespective of game structures. If the number of players are small, then the cooperation is favored in scale-free networks. △ Less

Submitted 22 January, 2017; v1 submitted 27 February, 2010; originally announced March 2010.

Comments: It is added that if the number of players are small, then the cooperation is favored in scale-free networks

Journal ref: Journal of Theoretical Biology, 269(1): 224 - 233, 2011