-
Testing Compact, Fused Silica Resonator Based Inertial Sensors in a Gravitational Wave Detector Prototype Facility
Authors:
J J Carter,
P Birckigt,
J Lehmann,
A Basalaev,
S L Kranzhoff,
S Al-Kershi,
M Carlassara,
G Chiarini,
F Khan,
G Leibeling,
H Lück,
C Rothhardt,
S Risse,
P Sarkar,
S Takano,
J von Wrangel,
D S Wu,
S M Koehlenbeck
Abstract:
Future gravitational wave observatories require significant advances in all aspects of their seismic isolation; inertial sensors being a pressing example. Inertial sensors using gram-scale high mechanical Q factor (Q) glass resonators combined with compact interferometric readout are promising alternatives to kilogram-scale conventional inertial sensors. We have produced fused silica resonators su…
▽ More
Future gravitational wave observatories require significant advances in all aspects of their seismic isolation; inertial sensors being a pressing example. Inertial sensors using gram-scale high mechanical Q factor (Q) glass resonators combined with compact interferometric readout are promising alternatives to kilogram-scale conventional inertial sensors. We have produced fused silica resonators suitable for low frequency inertial sensing and demonstrated that Qs of over 150,000 are possible. One resonator we produced was combined with a homodyne quadrature interferometer (HoQI) to read out the test mass displacement to form an inertial sensor. This is the first time a HoQI was used with a high Q resonator. The resulting sensor was tested against other commercial, kilogram scale inertial sensors at the AEI 10\,m Prototype facility. Despite the dynamic range challenges induced by the test mass motion, we can match the excellent noise floors HoQIs have achieved so far with slow-moving or stationary test masses, showing HoQIs as an excellent candidate for the readout of such sensors. We evaluate the setup as an inertial sensor, showing the best performance demonstrated by any gram-scale sensor to date, with comparable sensitivity to the significantly bulkier sensors used in gravitational wave detectors today. These sensors' compact size, self-calibration, and vacuum compatibility make them ideal candidates for the inertial sensing requirements in future gravitational wave detectors.
△ Less
Submitted 29 April, 2025;
originally announced April 2025.
-
Understanding Surgical smoke in Laparoscopy through Lagrangian Coherent Structures
Authors:
Sandeep Kumar,
Caroline Crowley,
Mohammad Faraz Khan,
Miguel D. Bustamante,
Ronan Cahill,
Kevin Nolan
Abstract:
In laparoscopic surgery, one of the main byproducts is the gaseous particles, called surgical smoke, which is found hazardous for both the patient and the operating room staff due to their chemical composition, and this implies a need for its effective elimination. The dynamics of surgical smoke are monitored by the underlying flow inside the abdomen and the hidden Lagrangian Coherent Structures (…
▽ More
In laparoscopic surgery, one of the main byproducts is the gaseous particles, called surgical smoke, which is found hazardous for both the patient and the operating room staff due to their chemical composition, and this implies a need for its effective elimination. The dynamics of surgical smoke are monitored by the underlying flow inside the abdomen and the hidden Lagrangian Coherent Structures (LCSs) present therein. In this article, for an insufflated abdomen domain, we analyse the velocity field, obtained from a computational fluid dynamics model, {first, by calculating the flow rates for the outlets} and then by identifying the patterns which are responsible for the transportation, mixing and accumulation of the material particles in the flow. From the finite time Lyapunov exponent (FTLE) field calculated for different planar cross sections of the domain, we show that these material curves are dependent on the angle, positions and number of the outlets, and the inlet. The ridges of the backward FTLE field reveal the regions of vortex formation, and the maximum accumulation, details which can inform the effective placement of the instruments for efficient removal of the surgical smoke.
△ Less
Submitted 25 January, 2025;
originally announced January 2025.
-
Efficient Localized Adaptation of Neural Weather Forecasting: A Case Study in the MENA Region
Authors:
Muhammad Akhtar Munir,
Fahad Shahbaz Khan,
Salman Khan
Abstract:
Accurate weather and climate modeling is critical for both scientific advancement and safeguarding communities against environmental risks. Traditional approaches rely heavily on Numerical Weather Prediction (NWP) models, which simulate energy and matter flow across Earth's systems. However, heavy computational requirements and low efficiency restrict the suitability of NWP, leading to a pressing…
▽ More
Accurate weather and climate modeling is critical for both scientific advancement and safeguarding communities against environmental risks. Traditional approaches rely heavily on Numerical Weather Prediction (NWP) models, which simulate energy and matter flow across Earth's systems. However, heavy computational requirements and low efficiency restrict the suitability of NWP, leading to a pressing need for enhanced modeling techniques. Neural network-based models have emerged as promising alternatives, leveraging data-driven approaches to forecast atmospheric variables. In this work, we focus on limited-area modeling and train our model specifically for localized region-level downstream tasks. As a case study, we consider the MENA region due to its unique climatic challenges, where accurate localized weather forecasting is crucial for managing water resources, agriculture and mitigating the impacts of extreme weather events. This targeted approach allows us to tailor the model's capabilities to the unique conditions of the region of interest. Our study aims to validate the effectiveness of integrating parameter-efficient fine-tuning (PEFT) methodologies, specifically Low-Rank Adaptation (LoRA) and its variants, to enhance forecast accuracy, as well as training speed, computational resource utilization, and memory efficiency in weather and climate modeling for specific regions.
△ Less
Submitted 11 September, 2024;
originally announced September 2024.
-
Using graph neural networks to reconstruct charged pion showers in the CMS High Granularity Calorimeter
Authors:
M. Aamir,
G. Adamov,
T. Adams,
C. Adloff,
S. Afanasiev,
C. Agrawal,
C. Agrawal,
A. Ahmad,
H. A. Ahmed,
S. Akbar,
N. Akchurin,
B. Akgul,
B. Akgun,
R. O. Akpinar,
E. Aktas,
A. Al Kadhim,
V. Alexakhin,
J. Alimena,
J. Alison,
A. Alpana,
W. Alshehri,
P. Alvarez Dominguez,
M. Alyari,
C. Amendola,
R. B. Amir
, et al. (550 additional authors not shown)
Abstract:
A novel method to reconstruct the energy of hadronic showers in the CMS High Granularity Calorimeter (HGCAL) is presented. The HGCAL is a sampling calorimeter with very fine transverse and longitudinal granularity. The active media are silicon sensors and scintillator tiles readout by SiPMs and the absorbers are a combination of lead and Cu/CuW in the electromagnetic section, and steel in the hadr…
▽ More
A novel method to reconstruct the energy of hadronic showers in the CMS High Granularity Calorimeter (HGCAL) is presented. The HGCAL is a sampling calorimeter with very fine transverse and longitudinal granularity. The active media are silicon sensors and scintillator tiles readout by SiPMs and the absorbers are a combination of lead and Cu/CuW in the electromagnetic section, and steel in the hadronic section. The shower reconstruction method is based on graph neural networks and it makes use of a dynamic reduction network architecture. It is shown that the algorithm is able to capture and mitigate the main effects that normally hinder the reconstruction of hadronic showers using classical reconstruction methods, by compensating for fluctuations in the multiplicity, energy, and spatial distributions of the shower's constituents. The performance of the algorithm is evaluated using test beam data collected in 2018 prototype of the CMS HGCAL accompanied by a section of the CALICE AHCAL prototype. The capability of the method to mitigate the impact of energy leakage from the calorimeter is also demonstrated.
△ Less
Submitted 18 December, 2024; v1 submitted 17 June, 2024;
originally announced June 2024.
-
Single color digital H&E staining with In-and-Out Net
Authors:
Mengkun Chen,
Yen-Tung Liu,
Fadeel Sher Khan,
Matthew C. Fox,
Jason S. Reichenberg,
Fabiana C. P. S. Lopes,
Katherine R. Sebastian,
Mia K. Markey,
James W. Tunnell
Abstract:
Virtual staining streamlines traditional staining procedures by digitally generating stained images from unstained or differently stained images. While conventional staining methods involve time-consuming chemical processes, virtual staining offers an efficient and low infrastructure alternative. Leveraging microscopy-based techniques, such as confocal microscopy, researchers can expedite tissue a…
▽ More
Virtual staining streamlines traditional staining procedures by digitally generating stained images from unstained or differently stained images. While conventional staining methods involve time-consuming chemical processes, virtual staining offers an efficient and low infrastructure alternative. Leveraging microscopy-based techniques, such as confocal microscopy, researchers can expedite tissue analysis without the need for physical sectioning. However, interpreting grayscale or pseudo-color microscopic images remains a challenge for pathologists and surgeons accustomed to traditional histologically stained images. To fill this gap, various studies explore digitally simulating staining to mimic targeted histological stains. This paper introduces a novel network, In-and-Out Net, specifically designed for virtual staining tasks. Based on Generative Adversarial Networks (GAN), our model efficiently transforms Reflectance Confocal Microscopy (RCM) images into Hematoxylin and Eosin (H&E) stained images. We enhance nuclei contrast in RCM images using aluminum chloride preprocessing for skin tissues. Training the model with virtual H\&E labels featuring two fluorescence channels eliminates the need for image registration and provides pixel-level ground truth. Our contributions include proposing an optimal training strategy, conducting a comparative analysis demonstrating state-of-the-art performance, validating the model through an ablation study, and collecting perfectly matched input and ground truth images without registration. In-and-Out Net showcases promising results, offering a valuable tool for virtual staining tasks and advancing the field of histological image analysis.
△ Less
Submitted 22 November, 2024; v1 submitted 21 May, 2024;
originally announced May 2024.
-
VortexViz: Finding Vortex Boundaries by Learning from Particle Trajectories
Authors:
Akila de Silva,
Nicholas Tee,
Omkar Ghanekar,
Fahim Hasan Khan,
Gregory Dusek,
James Davis,
Alex Pang
Abstract:
Vortices are studied in various scientific disciplines, offering insights into fluid flow behavior. Visualizing the boundary of vortices is crucial for understanding flow phenomena and detecting flow irregularities. This paper addresses the challenge of accurately extracting vortex boundaries using deep learning techniques. While existing methods primarily train on velocity components, we propose…
▽ More
Vortices are studied in various scientific disciplines, offering insights into fluid flow behavior. Visualizing the boundary of vortices is crucial for understanding flow phenomena and detecting flow irregularities. This paper addresses the challenge of accurately extracting vortex boundaries using deep learning techniques. While existing methods primarily train on velocity components, we propose a novel approach incorporating particle trajectories (streamlines or pathlines) into the learning process. By leveraging the regional/local characteristics of the flow field captured by streamlines or pathlines, our methodology aims to enhance the accuracy of vortex boundary extraction.
△ Less
Submitted 1 April, 2024;
originally announced April 2024.
-
Design and Analysis of Arc-Shaped Single Core Photonic Crystal Fiber Sensor Based on Surface Plasmon Resonance
Authors:
Tasmiah Tunazzina,
Fairuz Areefin Khan,
Anuva Chowdhury
Abstract:
The selection of a suitable plasmonic material is extremely crucial for achieving high-performance photonic crystal fiber-based surface plasmon resonance (PCF-SPR) sensors. However, most numerical investigations to date are limited to PCF-SPR sensors with conventional circularly coated plasmonic metals due to their availability and rigid properties. In this work, a single-core arc-shaped photonic…
▽ More
The selection of a suitable plasmonic material is extremely crucial for achieving high-performance photonic crystal fiber-based surface plasmon resonance (PCF-SPR) sensors. However, most numerical investigations to date are limited to PCF-SPR sensors with conventional circularly coated plasmonic metals due to their availability and rigid properties. In this work, a single-core arc-shaped photonic crystal fiber is designed and studied with sensing ingredients coated outside the fiber. The simulation and numerical analyses were performed using the full-vector finite element method (FV-FEM) to examine the effects of using gold as active metal and also the deposition of $Ta_2 O_5$ on gold. The results show that the arc-shaped sensor with gold film can obtain the maximum wavelength interrogation sensitivity (WIS) of 9500 nm/RIU within the refractive index (RI) range of 1.25 to 1.39 while the maximum amplitude interrogation sensitivity (AIS) is reached 579.26 $RIU^{-1}$ at 1.39 and resolution is found to be 1.05 x ${10^{-5}}$. However, depositing $Ta_2 O_5$ on the gold gives an improved maximum WIS and AIS of 22000 nm/RIU, and 1209.21 $RIU^{-1}$, respectively. With the coating of $Ta_2 O_5$, the resolution improves to 4.55 x ${10^{-6}}$ making the proposed sensor design undoubtedly effective in detecting different biological samples with a wide range of RI.
△ Less
Submitted 15 July, 2023;
originally announced July 2023.
-
Platform for Probing Radiation Transport Properties of Hydrogen at Conditions Found in the Deep Interiors of Red Dwarfs
Authors:
J. Lütgert,
M. Bethkenhagen,
B. Bachmann,
L. Divol,
D. O. Gericke,
S. H. Glenzer,
G. N. Hall,
N. Izumi,
S. F. Khan,
O. L. Landen,
S. A. MacLaren,
L. Masse,
R. Redmer,
M. Schörner,
M. O. Schölmerich,
S. Schumacher,
N. R. Shaffer,
C. E. Starrett,
P. A. Sterne,
C. Trosseille,
T. Döppner,
D. Kraus
Abstract:
We describe an experimental concept at the National Ignition Facility for specifically tailored spherical implosions to compress hydrogen to extreme densities (up to $\sim$800$\times$ solid density, electron number density n$_e$$\sim$4$\times$10$^{25}$ cm$^{-3}$ ) at moderate temperatures (T$\sim$200 eV), i.e., to conditions, which are relevant to the interiors of red dwarf stars. The dense plasma…
▽ More
We describe an experimental concept at the National Ignition Facility for specifically tailored spherical implosions to compress hydrogen to extreme densities (up to $\sim$800$\times$ solid density, electron number density n$_e$$\sim$4$\times$10$^{25}$ cm$^{-3}$ ) at moderate temperatures (T$\sim$200 eV), i.e., to conditions, which are relevant to the interiors of red dwarf stars. The dense plasma will be probed by laser-generated x-ray radiation of different photon energy to determine the plasma opacity due to collisional (free-free) absorption and Thomson scattering. The obtained results will benchmark radiation transport models, which in the case for free-free absorption show strong deviations at conditions relevant to red dwarfs. This very first experimental test of free-free opacity models at these extreme states will help to constrain where inside those celestial objects energy transport is dominated by radiation or convection. Moreover, our study will inform models for other important processes in dense plasmas, which are based on electron-ion collisions, e.g., stopping of swift ions or electron-ion temperature relaxation.
△ Less
Submitted 20 January, 2023;
originally announced January 2023.
-
Removal of industrial dye and pharmaceutical product using the nano and micron-sized PS rough particles studded with Pt nanoparticles
Authors:
Faizan Khan,
Chandra Shekhar,
Tarak Mondal,
Manigandan Sabapathy
Abstract:
We show that the rough particles studded with platinum nanoparticles can be fabricated straightforwardly and in a single step at room temperature. These rough particles displayed a good catalytic power (100% removal efficiency) against a model industrial dye (methylene blue) and pharmaceutical residue (tetracycline) within a reasonable time scale. Further, we illustrate the effects of particle siz…
▽ More
We show that the rough particles studded with platinum nanoparticles can be fabricated straightforwardly and in a single step at room temperature. These rough particles displayed a good catalytic power (100% removal efficiency) against a model industrial dye (methylene blue) and pharmaceutical residue (tetracycline) within a reasonable time scale. Further, we illustrate the effects of particle size, concentration, and contact patterns on the performance of rough catalytic particles. The semi-batch conditions favoured the complete decomposition of tetracycline within 40 min, but the batch-wise operation offered a good contacting pattern for methylene blue yielding a maximal output within 10 min. The kinetics of the heterogeneous catalytic process modelled by Langmuir-Hinshelwood kinetics predicts that the given methylene blue decomposition reaction induced by the rough particles follows the pseudo-first-order kinetics. The rate constants for the reaction catalyzed by 0.6 and 1.0um-sized rough particles are 0.048 and 0.032 min^-1, respectively. Furthermore, we established the proof-of-concept using magnetically-responsive rough particles for real-time applications, including decontamination and recovery of catalyst particles via an externally applied magnetic field in one cycle. Our proposed method helps achieve a near-100% degrading efficiency within 10 to 40 min at minimal catalytic particle concentration, i.e., 200 ppm. Since we can turn the rough particles into super-paramagnetic, we can recover and reuse them for several wastewater treatment cycles without incurring any running costs.
△ Less
Submitted 10 January, 2023;
originally announced January 2023.
-
On Lagrangian Coherent Structures in Laparoscopy
Authors:
Sandeep Kumar,
Caroline Crowley,
Mohammad Faraz Khan,
Miguel D. Bustamante,
Ronan Cahill,
Kevin Nolan
Abstract:
Laparoscopy is an electrosurgical medical operation often involving an application of high-frequency alternating current to remove undesired biological tissue from the insufflated abdomen accessible through inlet and outlets trocars. One of the main byproducts in this process are the gaseous particles, called surgical smoke, which is found hazardous for both the patient and the operating room staf…
▽ More
Laparoscopy is an electrosurgical medical operation often involving an application of high-frequency alternating current to remove undesired biological tissue from the insufflated abdomen accessible through inlet and outlets trocars. One of the main byproducts in this process are the gaseous particles, called surgical smoke, which is found hazardous for both the patient and the operating room staff. The elimination of this hazardous material is an area of active research in the medical community. Thus, understanding dynamics influenced by the underlying flow inside the abdomen is crucial. In this article, we propose a computational fluid dynamics model and analyse the velocity field in an insufflated abdomen shaped domain by identifying the Lagrangian Coherent Structures (LCS) that are responsible for the transportation, mixing and accumulation of the material particles in the flow. By calculating the mixing strength we show that the regions revealed by these material curves are dependent on the angle, positions and number of the outlets and inlets. Hence, a novel utility of LCS in medical surgery is presented that can detail the dynamics of surgical smoke informing better design of effective smoke removal technologies.
△ Less
Submitted 24 December, 2022;
originally announced December 2022.
-
Performance of the CMS High Granularity Calorimeter prototype to charged pion beams of 20$-$300 GeV/c
Authors:
B. Acar,
G. Adamov,
C. Adloff,
S. Afanasiev,
N. Akchurin,
B. Akgün,
M. Alhusseini,
J. Alison,
J. P. Figueiredo de sa Sousa de Almeida,
P. G. Dias de Almeida,
A. Alpana,
M. Alyari,
I. Andreev,
U. Aras,
P. Aspell,
I. O. Atakisi,
O. Bach,
A. Baden,
G. Bakas,
A. Bakshi,
S. Banerjee,
P. DeBarbaro,
P. Bargassa,
D. Barney,
F. Beaudette
, et al. (435 additional authors not shown)
Abstract:
The upgrade of the CMS experiment for the high luminosity operation of the LHC comprises the replacement of the current endcap calorimeter by a high granularity sampling calorimeter (HGCAL). The electromagnetic section of the HGCAL is based on silicon sensors interspersed between lead and copper (or copper tungsten) absorbers. The hadronic section uses layers of stainless steel as an absorbing med…
▽ More
The upgrade of the CMS experiment for the high luminosity operation of the LHC comprises the replacement of the current endcap calorimeter by a high granularity sampling calorimeter (HGCAL). The electromagnetic section of the HGCAL is based on silicon sensors interspersed between lead and copper (or copper tungsten) absorbers. The hadronic section uses layers of stainless steel as an absorbing medium and silicon sensors as an active medium in the regions of high radiation exposure, and scintillator tiles directly readout by silicon photomultipliers in the remaining regions. As part of the development of the detector and its readout electronic components, a section of a silicon-based HGCAL prototype detector along with a section of the CALICE AHCAL prototype was exposed to muons, electrons and charged pions in beam test experiments at the H2 beamline at the CERN SPS in October 2018. The AHCAL uses the same technology as foreseen for the HGCAL but with much finer longitudinal segmentation. The performance of the calorimeters in terms of energy response and resolution, longitudinal and transverse shower profiles is studied using negatively charged pions, and is compared to GEANT4 predictions. This is the first report summarizing results of hadronic showers measured by the HGCAL prototype using beam test data.
△ Less
Submitted 27 May, 2023; v1 submitted 9 November, 2022;
originally announced November 2022.
-
Response of a CMS HGCAL silicon-pad electromagnetic calorimeter prototype to 20-300 GeV positrons
Authors:
B. Acar,
G. Adamov,
C. Adloff,
S. Afanasiev,
N. Akchurin,
B. Akgün,
F. Alam Khan,
M. Alhusseini,
J. Alison,
A. Alpana,
G. Altopp,
M. Alyari,
S. An,
S. Anagul,
I. Andreev,
P. Aspell,
I. O. Atakisi,
O. Bach,
A. Baden,
G. Bakas,
A. Bakshi,
S. Bannerjee,
P. Bargassa,
D. Barney,
F. Beaudette
, et al. (364 additional authors not shown)
Abstract:
The Compact Muon Solenoid Collaboration is designing a new high-granularity endcap calorimeter, HGCAL, to be installed later this decade. As part of this development work, a prototype system was built, with an electromagnetic section consisting of 14 double-sided structures, providing 28 sampling layers. Each sampling layer has an hexagonal module, where a multipad large-area silicon sensor is glu…
▽ More
The Compact Muon Solenoid Collaboration is designing a new high-granularity endcap calorimeter, HGCAL, to be installed later this decade. As part of this development work, a prototype system was built, with an electromagnetic section consisting of 14 double-sided structures, providing 28 sampling layers. Each sampling layer has an hexagonal module, where a multipad large-area silicon sensor is glued between an electronics circuit board and a metal baseplate. The sensor pads of approximately 1 cm$^2$ are wire-bonded to the circuit board and are readout by custom integrated circuits. The prototype was extensively tested with beams at CERN's Super Proton Synchrotron in 2018. Based on the data collected with beams of positrons, with energies ranging from 20 to 300 GeV, measurements of the energy resolution and linearity, the position and angular resolutions, and the shower shapes are presented and compared to a detailed Geant4 simulation.
△ Less
Submitted 31 March, 2022; v1 submitted 12 November, 2021;
originally announced November 2021.
-
Experiments conducted in the burning plasma regime with inertial fusion implosions
Authors:
J. S. Ross,
J. E. Ralph,
A. B. Zylstra,
A. L. Kritcher,
H. F. Robey,
C. V. Young,
O. A. Hurricane,
D. A. Callahan,
K. L. Baker,
D. T. Casey,
T. Doeppner,
L. Divol,
M. Hohenberger,
S. Le Pape,
A. Pak,
P. K. Patel,
R. Tommasini,
S. J. Ali,
P. A. Amendt,
L. J. Atherton,
B. Bachmann,
D. Bailey,
L. R. Benedetti,
L. Berzak Hopkins,
R. Betti
, et al. (127 additional authors not shown)
Abstract:
An experimental program is currently underway at the National Ignition Facility (NIF) to compress deuterium and tritium (DT) fuel to densities and temperatures sufficient to achieve fusion and energy gain. The primary approach being investigated is indirect drive inertial confinement fusion (ICF), where a high-Z radiation cavity (a hohlraum) is heated by lasers, converting the incident energy into…
▽ More
An experimental program is currently underway at the National Ignition Facility (NIF) to compress deuterium and tritium (DT) fuel to densities and temperatures sufficient to achieve fusion and energy gain. The primary approach being investigated is indirect drive inertial confinement fusion (ICF), where a high-Z radiation cavity (a hohlraum) is heated by lasers, converting the incident energy into x-ray radiation which in turn drives the DT fuel filled capsule causing it to implode. Previous experiments reported DT fuel gain exceeding unity [O.A. Hurricane et al., Nature 506, 343 (2014)] and then exceeding the kinetic energy of the imploding fuel [S. Le Pape et al., Phys. Rev. Lett. 120, 245003 (2018)]. We report on recent experiments that have achieved record fusion neutron yields on NIF, greater than 100 kJ with momentary fusion powers exceeding 1PW, and have for the first time entered the burning plasma regime where fusion alpha-heating of the fuel exceeds the energy delivered to the fuel via compression. This was accomplished by increasing the size of the high-density carbon (HDC) capsule, increasing energy coupling, while controlling symmetry and implosion design parameters. Two tactics were successful in controlling the radiation flux symmetry and therefore the implosion symmetry: transferring energy between laser cones via plasma waves, and changing the shape of the hohlraum. In conducting these experiments, we controlled for known sources of degradation. Herein we show how these experiments were performed to produce record performance, and demonstrate the data fidelity leading us to conclude that these shots have entered the burning plasma regime.
△ Less
Submitted 8 November, 2021;
originally announced November 2021.
-
Mobilkit: A Python Toolkit for Urban Resilience and Disaster Risk Management Analytics using High Frequency Human Mobility Data
Authors:
Enrico Ubaldi,
Takahiro Yabe,
Nicholas K. W. Jones,
Maham Faisal Khan,
Satish V. Ukkusuri,
Riccardo Di Clemente,
Emanuele Strano
Abstract:
Increasingly available high-frequency location datasets derived from smartphones provide unprecedented insight into trajectories of human mobility. These datasets can play a significant and growing role in informing preparedness and response to natural disasters. However, limited tools exist to enable rapid analytics using mobility data, and tend not to be tailored specifically for disaster risk m…
▽ More
Increasingly available high-frequency location datasets derived from smartphones provide unprecedented insight into trajectories of human mobility. These datasets can play a significant and growing role in informing preparedness and response to natural disasters. However, limited tools exist to enable rapid analytics using mobility data, and tend not to be tailored specifically for disaster risk management. We present an open-source, Python-based toolkit designed to conduct replicable and scalable post-disaster analytics using GPS location data. Privacy, system capabilities, and potential expansions of \textit{Mobilkit} are discussed.
△ Less
Submitted 16 September, 2021; v1 submitted 29 July, 2021;
originally announced July 2021.
-
Location Data Reveals Disproportionate Disaster Impact Amongst the Poor: A Case Study of the 2017 Puebla Earthquake Using Mobilkit
Authors:
Takahiro Yabe,
Nicholas K W Jones,
Nancy Lozano-Gracia,
Maham Faisal Khan,
Satish V. Ukkusuri,
Samuel Fraiberger,
Aleister Montfort
Abstract:
Location data obtained from smartphones is increasingly finding use cases in disaster risk management. Where traditionally, CDR has provided the predominant digital footprint for human mobility, GPS data now has immense potential in terms of improved spatiotemporal accuracy, volume, availability, and accessibility. GPS data has already proven invaluable in a range of pre- and post-disaster use cas…
▽ More
Location data obtained from smartphones is increasingly finding use cases in disaster risk management. Where traditionally, CDR has provided the predominant digital footprint for human mobility, GPS data now has immense potential in terms of improved spatiotemporal accuracy, volume, availability, and accessibility. GPS data has already proven invaluable in a range of pre- and post-disaster use cases, such as quantifying displacement, measuring rates of return and recovery, evaluating accessibility to critical resources, planning for resilience. Despite its popularity and potential, however, the use of GPS location data in DRM is still nascent, with several use cases yet to be explored. In this paper, we consider the 2017 Puebla Earthquake in Mexico to (i) validate and expand upon post-disaster analysis applications using GPS data, and (ii) illustrate the use of a new toolkit, Mobilkit, to facilitate scalable, replicable extensions of this work for a wide range of disasters, including earthquakes, typhoons, flooding, and beyond.
△ Less
Submitted 28 July, 2021;
originally announced July 2021.
-
Uncovering socioeconomic gaps in mobility reduction during the COVID-19 pandemic using location data
Authors:
Samuel P. Fraiberger,
Pablo Astudillo,
Lorenzo Candeago,
Alex Chunet,
Nicholas K. W. Jones,
Maham Faisal Khan,
Bruno Lepri,
Nancy Lozano Gracia,
Lorenzo Lucchini,
Emanuele Massaro,
Aleister Montfort
Abstract:
Using smartphone location data from Colombia, Mexico, and Indonesia, we investigate how non-pharmaceutical policy interventions intended to mitigate the spread of the COVID-19 pandemic impact human mobility. In all three countries, we find that following the implementation of mobility restriction measures, human movement decreased substantially. Importantly, we also uncover large and persistent di…
▽ More
Using smartphone location data from Colombia, Mexico, and Indonesia, we investigate how non-pharmaceutical policy interventions intended to mitigate the spread of the COVID-19 pandemic impact human mobility. In all three countries, we find that following the implementation of mobility restriction measures, human movement decreased substantially. Importantly, we also uncover large and persistent differences in mobility reduction between wealth groups: on average, users in the top decile of wealth reduced their mobility up to twice as much as users in the bottom decile. For decision-makers seeking to efficiently allocate resources to response efforts, these findings highlight that smartphone location data can be leveraged to tailor policies to the needs of specific socioeconomic groups, especially the most vulnerable.
△ Less
Submitted 27 July, 2020; v1 submitted 26 June, 2020;
originally announced June 2020.
-
MARVEL analysis of the measured high-resolution spectra of $^{14}$NH
Authors:
Daniel Darby-Lewis,
Het Shah,
Dhyeya Joshi,
Fahd Khan,
Miles Kauwo,
Nikhil Sethi,
Peter F. Bernath,
Tibor Furtenbacher,
Roland Tóbis,
Attila G. Császár,
Jonathan Tennyson
Abstract:
Rovibronic energy levels are determined for four low-lying electronic states (\X, \A, \Sa, and \Sc) of the imidogen free radical ($^{14}$NH) using the \Marvel\ (Measured Active Rotational-Vibrational Energy Levels) technique. Compilation of transitions from both laboratory measurements and solar spectra, found in 18 publications, yields a dataset of 3002 rovibronic transitions forming elements of…
▽ More
Rovibronic energy levels are determined for four low-lying electronic states (\X, \A, \Sa, and \Sc) of the imidogen free radical ($^{14}$NH) using the \Marvel\ (Measured Active Rotational-Vibrational Energy Levels) technique. Compilation of transitions from both laboratory measurements and solar spectra, found in 18 publications, yields a dataset of 3002 rovibronic transitions forming elements of a measured spectroscopic network (SN). At the end of the MARVEL procedure, the majority of the transitions form a single, self-consistent SN component of 2954 rovibronic transitions and 1058 energy levels, \NoX, \NoA, and \Noc\ for the \X, \A, and \Sc\ electronic states, respectively. The \Sa\ electronic state is characterized by \Noa\ $Λ$-doublet levels, counting each level only once. Electronic structure computations show that unusually the CCSD(T) method does not accurately predict the \Sa\ excitation energy even at the complete basis set limit.
△ Less
Submitted 7 July, 2019;
originally announced July 2019.
-
Nash embedding: a road map to realizing quantum hardware
Authors:
Faisal Shah Khan
Abstract:
The non-Euclidean nature of the mathematical model of quantum circuits leaves open the question of their practical implementation in hardware platforms which necessarily reside in the Euclidean space $\mathbb{R}^3$. On the other hand, reversible circuits are elements of Euclidean spaces, making their physical realization in hardware platforms possible and practical. Here, the quantum circuit model…
▽ More
The non-Euclidean nature of the mathematical model of quantum circuits leaves open the question of their practical implementation in hardware platforms which necessarily reside in the Euclidean space $\mathbb{R}^3$. On the other hand, reversible circuits are elements of Euclidean spaces, making their physical realization in hardware platforms possible and practical. Here, the quantum circuit model for quantum computing is mapped into that of reversible computing in a mathematically robust fashion using Nash embedding so that every quantum computation can be realized as an equivalent reversible one.
△ Less
Submitted 15 June, 2019; v1 submitted 9 June, 2019;
originally announced June 2019.
-
Dynamics of liquid crystal on hexagonal lattice
Authors:
Muhammad Arslan Shehzad,
Junsu Lee,
Sang Hoon Park,
Imtisal Akhtar,
Muhammad Farooq Khan,
Sajjad Hussain,
Jonghwa Eom,
Jongwan Jung,
Gunn Kim,
Chanyong Hwang,
Yongho Seo
Abstract:
Nematic liquid crystal (LC) molecules adsorbed on two dimensional materials are aligned along the crystal directions of the hexagonal lattice. It was demonstrated that short electric pulses can reorient the aligned LC molecules in the preferred armchair direction of hexagonal boron nitride (h-BN). Several states with a variety of colors were obtained by changing the direction and strength of the e…
▽ More
Nematic liquid crystal (LC) molecules adsorbed on two dimensional materials are aligned along the crystal directions of the hexagonal lattice. It was demonstrated that short electric pulses can reorient the aligned LC molecules in the preferred armchair direction of hexagonal boron nitride (h-BN). Several states with a variety of colors were obtained by changing the direction and strength of the electric pulses. The ab initio calculations based on density functional theory was carried out to determine the favorable adsorption configurations of the LC molecules on the h-BN surface. A non-volatile display, in which pixel resolution can be determined by grains of hexagonal surface, is proposed, which can offer a pathway towards dynamic high-quality pixels with low power consumption, and could define a new paradigm for all non-volatile display applications.
△ Less
Submitted 1 June, 2018;
originally announced June 2018.
-
Nanomechanical resonance captures pre-melting transition in DNA unravelling
Authors:
Keren Jiang,
Faheem Khan,
Javix Thomas,
Arindam Phani,
Thomas Thundat
Abstract:
A double-stranded DNA unravels thermally through intermediate denatured bubble segments. Intrinsically, fluctuations ensue at the bubble boundaries from non-equilibrium (NE) energy exchanges with the environment. However, such details gets obscured by large population kinetics at the macroscale, associating equilibrium pathway to the unravelling landscape. In this work, we capture evidence of fluc…
▽ More
A double-stranded DNA unravels thermally through intermediate denatured bubble segments. Intrinsically, fluctuations ensue at the bubble boundaries from non-equilibrium (NE) energy exchanges with the environment. However, such details gets obscured by large population kinetics at the macroscale, associating equilibrium pathway to the unravelling landscape. In this work, we capture evidence of fluctuation energetics with picoliter samples in a microfluidic cantilever. We exploit nanomechanical resonance to measure the NE energy exchanges through dissipation, revealing a crucial pre-melting transition at T~42C . This signifies that unravelling possibly proceeds via intermediate collapsed-bubble conformations releasing energy, sufficient to unbind bubble ends, assisting further unbinding. Fluctuation theorem explains the observations opening further avenues to investigate fluctuation kinetics in other biological phenomena that also proceed through similar NE energetics.
△ Less
Submitted 20 September, 2018; v1 submitted 31 May, 2018;
originally announced June 2018.
-
Phase Slip Solutions in Magnetically Modulated Taylor-Couette Flow
Authors:
Rainer Hollerbach,
Farzana Khan
Abstract:
We numerically investigate Taylor-Couette flow in a wide-gap configuration, with $r_i/r_o=1/2$, the inner cylinder rotating, and the outer cylinder stationary. The fluid is taken to be electrically conducting, and a magnetic field of the form $B_z\approx(1 + \cos(2πz/z_0))/2$ is externally imposed, where the wavelength $z_0=50(r_o-r_i)$. Taylor vortices form where the field is weak, but not where…
▽ More
We numerically investigate Taylor-Couette flow in a wide-gap configuration, with $r_i/r_o=1/2$, the inner cylinder rotating, and the outer cylinder stationary. The fluid is taken to be electrically conducting, and a magnetic field of the form $B_z\approx(1 + \cos(2πz/z_0))/2$ is externally imposed, where the wavelength $z_0=50(r_o-r_i)$. Taylor vortices form where the field is weak, but not where it is strong. As the Reynolds number measuring the rotation rate is increased, the initial onset of vortices involves phase slip events, whereby pairs of Taylor vortices are periodically formed and then drift outward, away from the midplane where $B_z=0$. Subsequent bifurcations lead to a variety of other solutions, including ones both symmetric and asymmetric about the midplane. For even larger Reynolds numbers a different type of phase slip arises, in which vortices form at the outer edges of the pattern and drift inward, disappearing abruptly at a certain point. These solutions can also be symmetric or asymmetric about the midplane, and co-exist at the same Reynolds number. Many of the dynamics of these phase slip solutions are qualitatively similar to previous results in geometrically ramped Taylor-Couette flows.
△ Less
Submitted 6 April, 2017;
originally announced April 2017.
-
3D conformal planning using low segment multi-criteria IMRT optimization
Authors:
Fazal Khan,
David Craft
Abstract:
Purpose: To evaluate automated multicriteria optimization (MCO)-- designed for intensity modulated radiation therapy (IMRT), but invoked with limited segmentation -- to efficiently produce high quality 3D conformal treatment (3D-CRT) plans.
Methods: Ten patients previously planned with 3D-CRT were replanned with a low-segment inverse multicriteria optimized technique. The MCO-3D plans used the s…
▽ More
Purpose: To evaluate automated multicriteria optimization (MCO)-- designed for intensity modulated radiation therapy (IMRT), but invoked with limited segmentation -- to efficiently produce high quality 3D conformal treatment (3D-CRT) plans.
Methods: Ten patients previously planned with 3D-CRT were replanned with a low-segment inverse multicriteria optimized technique. The MCO-3D plans used the same number of beams, beam geometry and machine parameters of the corresponding 3D plans, but were limited to an energy of 6 MV. The MCO-3D plans were optimized using a fluence-based MCO IMRT algorithm and then, after MCO navigation, segmented with a low number of segments. The 3D and MCO-3D plans were compared by evaluating mean doses to individual organs at risk (OARs), mean doses to combined OARs, homogeneity indexes (HI), monitor units (MUs), physician preference, and qualitative assessments of planning time and plan customizability.
Results: The MCO-3D plans significantly reduced the OAR mean doses and monitor units while maintaining good coverage and homogeneity of target volumes. MCO allows for more streamlined plan customization. All MCO-3D plans were preferred by physicians over their corresponding 3D plans.
Conclusion: High quality 3D plans can be produced using IMRT optimization technology, resulting in automated field-in-field type plans with good monitor unit efficiency. Adopting this technology in a clinic could streamline treatment plan production.
△ Less
Submitted 31 January, 2014;
originally announced January 2014.
-
Enhanced coupling design of a detuned damped structure for clic
Authors:
A. D'Elia,
R. M. Jones,
A. Grudiev,
T. Higo,
V. F. Khan,
W. Wuensch
Abstract:
The key feature of the improved coupling design in the Damped Detuned Structure (DDS) is focused on the four manifolds. Rectangular geometry slots and rectangular manifolds are used. This results in a significantly stronger coupling to the manifolds compared to the previous design. We describe the new design together with its wakefield damping properties.
The key feature of the improved coupling design in the Damped Detuned Structure (DDS) is focused on the four manifolds. Rectangular geometry slots and rectangular manifolds are used. This results in a significantly stronger coupling to the manifolds compared to the previous design. We describe the new design together with its wakefield damping properties.
△ Less
Submitted 16 May, 2012;
originally announced May 2012.
-
Comparative Wakefield Analysis of a First Prototype of a DDS Structure for CLIC Main Linac
Authors:
A. D'Elia,
R. M. Jones,
V. F. Khan,
A. Grudiev,
W. Wuensch
Abstract:
A Damped Detuned Structure (DDS) for CLIC main linac has been proposed as an alternative to the present baseline design which is based on heavy damping. A first prototype, CLIC_DDS_A, for high power tests has been already designed and is under construction. It is also foreseen to design a further prototype, CLIC_DDS_B, to test both the wakefield suppression and high power performances. Wakefield c…
▽ More
A Damped Detuned Structure (DDS) for CLIC main linac has been proposed as an alternative to the present baseline design which is based on heavy damping. A first prototype, CLIC_DDS_A, for high power tests has been already designed and is under construction. It is also foreseen to design a further prototype, CLIC_DDS_B, to test both the wakefield suppression and high power performances. Wakefield calculations for DDS are, in the early design stage, based on single infinitely periodic cells. Though cell-to-cell interaction is taken into account to calculate the wakefields, it is important to study full structure properties using computational tools. In particular this is fundamental for defining the input parameters for the HOM coupler that is crucial for the performances of DDS. In the following a full analysis of wakefields and impedances based on simulations conducted with finite difference based electromagnetic computer code GdfidL will be presented.
△ Less
Submitted 6 October, 2011;
originally announced October 2011.
-
A High Phase Advance Damped and Detuned Structure for the Main Linacs of Clic
Authors:
V. F. Khan,
A. D'Elia,
A. Grudiev,
R. M. Jones,
W. Wuensch
Abstract:
The main accelerating structures for the CLIC are designed to operate at an average accelerating gradient of 100 MV/m. The accelerating frequency has been optimised to 11.994 GHz with a phase advance of 2π/3 of the main accelerating mode. The moderately damped and detuned structure (DDS) design is being studied as an alternative to the strongly damped WDS design. Both these designs are based on th…
▽ More
The main accelerating structures for the CLIC are designed to operate at an average accelerating gradient of 100 MV/m. The accelerating frequency has been optimised to 11.994 GHz with a phase advance of 2π/3 of the main accelerating mode. The moderately damped and detuned structure (DDS) design is being studied as an alternative to the strongly damped WDS design. Both these designs are based on the nominal accelerating phase advance. Here we explore high phase advance (HPA) structures in which the group velocity of the rf fields is reduced compared to that of standard (2π/3) structures. The electrical breakdown strongly depends on the fundamental mode group velocity. Hence it is expected that electrical breakdown is less likely to occur in the HPA structures. We report on a study of both the fundamental and dipole modes in a CLIC_DDS_HPA structure, designed to operate at 5π/6 phase advance per cell. Higher order dipole modes in both the standard and HPA structures are also studied.
△ Less
Submitted 3 October, 2010;
originally announced October 2010.
-
Recent Progress on a Manifold Damped and Detuned Structure for CLIC
Authors:
V. F. Khan,
A. D'Elia,
A. Grudiev,
R. M. Jones,
W. Wuensch,
R. Zennaro
Abstract:
A damped detuned structure for the main X-band linacs of CLIC is being investigated as an alternative design to the present baseline heavily damped structure. In our earlier designs we studied detuned structures, operating at 11.994 GHz, with a range of dipole bandwidths in order to ensure the structure satisfies beam dynamics and rf breakdown constraints. Here we report on the development of a da…
▽ More
A damped detuned structure for the main X-band linacs of CLIC is being investigated as an alternative design to the present baseline heavily damped structure. In our earlier designs we studied detuned structures, operating at 11.994 GHz, with a range of dipole bandwidths in order to ensure the structure satisfies beam dynamics and rf breakdown constraints. Here we report on the development of a damped and detuned structure which satisfies both constraints. Preparations for high power testing of the structure are also discussed
△ Less
Submitted 1 June, 2010;
originally announced June 2010.
-
Investigation of an alternate means of wakefield suppression in the main linacs of CLIC
Authors:
V. F. Khan,
R. M. Jones
Abstract:
We report on suppression of long-range wakefields in CLIC accelerating structures. Strong detuning and moderate damping is employed. In these initial design studies we focus on the CLIC_G structure and enforce a moderate Q of 300 and 500. We maintain a dipole bandwidth of approximately 1 GHz as specified from breakdown constraints in a modified structure, CLIC_DDS. The circuit model, which facil…
▽ More
We report on suppression of long-range wakefields in CLIC accelerating structures. Strong detuning and moderate damping is employed. In these initial design studies we focus on the CLIC_G structure and enforce a moderate Q of 300 and 500. We maintain a dipole bandwidth of approximately 1 GHz as specified from breakdown constraints in a modified structure, CLIC_DDS. The circuit model, which facilitates a rapid design of manifolds slot-coupled to the main accelerating cells, is described.
△ Less
Submitted 19 June, 2009;
originally announced June 2009.
-
An alternate design for CLIC main linac wakefield suppression
Authors:
V. F. Khan,
R. M. Jones
Abstract:
The present design of the main accelerating structure for CLIC is based on heavy damping (WDS) with a Q of ~10. The wakefield suppression in this case entails locating the damping materials in relatively close proximity to the accelerating cells. Herein we present an alternate design for the main accelerating structures. We detune the lowest dipole band by prescribing a Gaussian distribution to…
▽ More
The present design of the main accelerating structure for CLIC is based on heavy damping (WDS) with a Q of ~10. The wakefield suppression in this case entails locating the damping materials in relatively close proximity to the accelerating cells. Herein we present an alternate design for the main accelerating structures. We detune the lowest dipole band by prescribing a Gaussian distribution to the cell parameters and consider moderate damping Q~500 to prevent the recoherence of the modes; in this case the damping materials can be located at an extended distance from the accelerating structure. The procedure to achieve a well-damped wakefield is described. Results are presented elucidating the various designs including the current one which is being developed to incorporate r.f. breakdown, pulse surface heating and beam dynamics constraints.
△ Less
Submitted 11 March, 2009;
originally announced March 2009.
