-
Analysis of RF Sheath-Driven Tungsten Erosion at RF Antenna in the WEST Tokamak
Authors:
A. Kumar,
W. Tierens,
T. Younkin,
C. Johnson,
C. Klepper,
A. Diaw,
J. Lore,
A. Grosjean,
G. Urbanczyk,
J. Hillairet,
P. Tamain,
L. Colas,
C. Guillemaut,
D. Current,
S. Shiraiwa,
N. Bertelli,
the WEST Team
Abstract:
This study applies the newly developed STRIPE (Simulated Transport of RF Impurity Production and Emission) framework to interpret tungsten (W) erosion at RF antenna structures in the WEST tokamak. STRIPE integrates SolEdge3x for edge plasma backgrounds, COMSOL for 3D RF sheath potentials, RustBCA for sputtering yields, and GITR for impurity transport and ion energy-angle distributions. In contrast…
▽ More
This study applies the newly developed STRIPE (Simulated Transport of RF Impurity Production and Emission) framework to interpret tungsten (W) erosion at RF antenna structures in the WEST tokamak. STRIPE integrates SolEdge3x for edge plasma backgrounds, COMSOL for 3D RF sheath potentials, RustBCA for sputtering yields, and GITR for impurity transport and ion energy-angle distributions. In contrast to prior work by Kumar et al. 2025 Nucl. Fusion 65, 076039, which focused on framework validation for WEST ICRH discharge 57877, the present study provides a spatially resolved analysis of gross W erosion at both Q2 antenna limiters under ohmic and ICRH conditions. Using 2D SolEdge3x profiles in COMSOL, STRIPE captures rectified sheath potentials exceeding 300 V, leading to strong upper-limiter localization. Both poloidal and toroidal asymmetries are observed and attributed to RF sheath effects, with modeled erosion patterns deviating from experiment - highlighting sensitivity to sheath geometry and plasma resolution. High-charge-state oxygen ions (O6+-O8+) dominate erosion, while D+ contributes negligibly. A plasma composition of 1 percent oxygen and 98 percent deuterium is assumed. STRIPE predicts a 30-fold increase in gross W erosion from ohmic to ICRH phases, consistent with W-I 400.9 nm brightness measurements. Agreement within 5 percent (ohmic) and 30 percent (ICRH) demonstrates predictive capability and supports STRIPE's application in reactor-scale antenna design.
△ Less
Submitted 8 July, 2025;
originally announced July 2025.
-
ANSYS HFSS as a new numerical tool to study wave propagation inside anisotropic magnetized plasmas in the Ion Cylotron Range of Frequencies
Authors:
V. Maquet,
R. Ragona,
D. Van Eester,
J. Hillairet,
F. Durodie
Abstract:
The paper demonstrates the possibility to use ANSYS HFSS as a versatile simulating tool for antennas facing inhomogeneous anisotropic magnetized plasmas in the Ion Cyclotron Range of Frequencies (ICRF). The methodology used throughout the paper is first illustrated with a uniform plasma case. We then extend this method to 1D plasma density profiles where we perform a first benchmark against the AN…
▽ More
The paper demonstrates the possibility to use ANSYS HFSS as a versatile simulating tool for antennas facing inhomogeneous anisotropic magnetized plasmas in the Ion Cyclotron Range of Frequencies (ICRF). The methodology used throughout the paper is first illustrated with a uniform plasma case. We then extend this method to 1D plasma density profiles where we perform a first benchmark against the ANTITER II code. The possibility to include more complex phenomena relevant to the ICRF field in future works like the lower hybrid resonance, the edge propagation of slow waves, sheaths and ponderomotive forces is also discussed. We finally present a 3D case for WEST and compare the radiation resistance calculated by the code to the experimental data. The main result of this paper - the implementation of a cold plasma medium in HFSS - is general and we hope it will also benefit to research fields besides controlled fusion.
△ Less
Submitted 25 September, 2023;
originally announced September 2023.
-
Minimization of the edge modes and near fields of a Travelling Wave Array antenna for WEST
Authors:
V. Maquet,
R. Ragona,
F. Durodié,
J. Hillairet
Abstract:
The Travelling Wave Array (TWA) antenna was proposed as a promising alternative for Ion Cyclotron Resonant Heating (ICRH) in future fusion reactors. In this study, the possibility to make a TWA compatible with a tungsten environment like the WEST tokamak is assessed. For this purpose, two aspects of the antenna are investigated: the power spectrum and the near fields excited by the antenna. The se…
▽ More
The Travelling Wave Array (TWA) antenna was proposed as a promising alternative for Ion Cyclotron Resonant Heating (ICRH) in future fusion reactors. In this study, the possibility to make a TWA compatible with a tungsten environment like the WEST tokamak is assessed. For this purpose, two aspects of the antenna are investigated: the power spectrum and the near fields excited by the antenna. The sensitivity of these parameters to load and capacitor layout variations is taken into account while satisfying a proper antenna frequency response. The sensitivity of the power spectrum to frequency variation is also investigated to allow the possibility of fast feedback of the power deposition into the core plasma of WEST. The high resilience of the TWA to these variations is demonstrated and the main parameters of the TWA expected in WEST are compared to the WEST Q2 antenna for the same loading. Possible optimizations of the TWA antenna are discussed. The present study is fully transferable to a fusion reactor like DEMO or ARC.
△ Less
Submitted 25 January, 2023;
originally announced January 2023.
-
Characterizations of thermal stability and electrical performance of Au-Ni coating on CuCrZr substrate for high vacuum radio-frequency contact application
Authors:
Z Chen,
Julien Hillairet,
V. Turq,
Y. T. Song,
R. Laloo,
Jean-Michel Bernard,
K. Vulliez,
G. Lombard,
C. Hernandez,
Q. X. Yang,
L. Ferreira,
F. Fesquet,
P. Mollard,
R. Volpe
Abstract:
Radio-frequency (RF) contacts-which are an example of electrical contacts-are commonly employed on accelerators and nuclear fusion experimental devices. RF contacts with a current load of 2 kA for steady-state operation were designed for application to the International Thermonuclear Experimental Reactor (ITER) device. In contrast to the typical working conditions of general commercial electrical…
▽ More
Radio-frequency (RF) contacts-which are an example of electrical contacts-are commonly employed on accelerators and nuclear fusion experimental devices. RF contacts with a current load of 2 kA for steady-state operation were designed for application to the International Thermonuclear Experimental Reactor (ITER) device. In contrast to the typical working conditions of general commercial electrical contacts, those of RF contacts employed on fusion devices include high vacuum, high temperature, and neutron radiation. CuCrZr is currently of interest as a base material for the manufacture of louvers of RF contacts, which has excellent thermal and electrical properties and has low creep rate at 250 {\textdegree}C. In this study, a hard Au coating (Au-Ni) was electroplated on CuCrZr samples and the samples were then subjected to thermal aging treatment at 250 {\textdegree}C for 500 h in order to simulate the vacuum-commissioning process of the ITER. The effects of thermal aging on the hardness, elastic modulus, crystallite size, and compositions of the coating were investigated via microstructural and mechanical characterizations of the coating material. Metal atom migration in different coating layers during thermal aging was characterized and evaluated via scanning electron microscopy/energy dispersive X-ray spectroscopy observations of the cross-sectional surfaces, and the obtained results could be used to directly select the coating thickness for the final RF contact component. The contact resistance-an important parameter of the RF contact-was measured in a dedicated testbed built to simulate fusion reactor conditions between CuCrZr pins and stainless steel plates coated with Au-Ni and Rh, respectively.
△ Less
Submitted 8 April, 2019;
originally announced July 2019.
-
Radiofrequency and Mechanical Tests of Silver Coated CuCrZr Contacts for the ITER Ion Cyclotron Antenna
Authors:
Julien Hillairet,
Z. Chen,
G Lombard,
J Delaplanche,
K Vulliez,
Q. Yang,
B. Beaumont,
F Calarco,
N Charabot,
F Kazarian,
P Lamalle,
J Bernard,
V Bruno,
J Hatchressian,
R Laloo,
P Mollard,
Y Song,
V Turq,
R Volpe
Abstract:
The ITER Ion Cyclotron Resonance Heating (ICRH) system is designed to couple to the plasma 20 MW of RF power from two antennas in the 40-55 MHz frequency range during long pulses of up to 3600 s and under various plasma conditions with Edge Localized Modes. Radio-Frequency (RF) contacts are integrated within the ITER ICRH launcher in order to ensure the RF current continuity and ease the mechanica…
▽ More
The ITER Ion Cyclotron Resonance Heating (ICRH) system is designed to couple to the plasma 20 MW of RF power from two antennas in the 40-55 MHz frequency range during long pulses of up to 3600 s and under various plasma conditions with Edge Localized Modes. Radio-Frequency (RF) contacts are integrated within the ITER ICRH launcher in order to ensure the RF current continuity and ease the mechanical assembly by allowing the free thermal expansion of the Removable Vacuum Transmission Line coaxial conductors during RF operations or during 250{\textdegree}C baking phases. A material study has been carried out to determine which materials and associated coatings are relevant for RF contacts application in ITER. In parallel, RF tests have been performed with a new prototype of Multi-Contact (r) LA-CUT/0,25/0 contacts made of silver-coated CuCrZr louvers. During these tests on a RF vacuum resonator, currents between 1.2 kA and 1.3 kA peak have been reached a few tens of times in steady-state conditions without any visible damage on the louvers. A final 62MHz pulse ending in a 300s flat top at 1.9kA resulted in severe damage to the contact. In addition, a test bed which performs sliding test cycles has been built in order to reproduce the wear of the contact prototype after 30 000 sliding cycles on a 3 mm stroke at 175{\textdegree}C under vacuum. The silver coating of the louvers is removed after approximately a hundred cycles whilst, to the contrary, damage to the CuCrZr louvers is relatively low.
△ Less
Submitted 15 February, 2018; v1 submitted 10 October, 2017;
originally announced October 2017.
-
Multipactor in High Power Radio-Frequency Systems for Nuclear Fusion
Authors:
Julien Hillairet,
Marc Goniche,
Nicolas Fil,
Mohamed Belhaj,
Jérôme Puech
Abstract:
Magnetic confinement fusion researches are an approach to demonstrate the feasibility of nuclear fusion power for energy production. In these experiments, mega-watt range power Radio-Frequency waves, from tens of MHz to hundreds of GHz, are injected into magnetically confined plasmas in order to increase its temperature and to extend its duration. These RF systems are subjected to the magnetic fie…
▽ More
Magnetic confinement fusion researches are an approach to demonstrate the feasibility of nuclear fusion power for energy production. In these experiments, mega-watt range power Radio-Frequency waves, from tens of MHz to hundreds of GHz, are injected into magnetically confined plasmas in order to increase its temperature and to extend its duration. These RF systems are subjected to the magnetic field environment of the experiments, ranging from few tenth of Tesla to Tesla, and various orientations depending of their locations. As these RF systems made of copper, silver or ceramics are located in vacuum environments, they are subject to multipactor discharges. These discharges are generally considered detrimental since they can lead to detuned RF systems, limit the RF power transmission in the plasma and eventually damage RF sources or components. In some case, especially in the MHz range of frequency, multipactor discharges can be desired for vacuum conditioning. This paper presents the various RF systems used in magnetic fusion experiments and review the work performed in the fusion research community on multipactor discharges for high power coaxial (MHz) and rectangular waveguides (GHz) transmission lines, with their practical implications on power delivery into the plasma.
△ Less
Submitted 10 October, 2017;
originally announced October 2017.
-
Ion cyclotron resonance heating systems upgrade toward high power and CW operations in WEST
Authors:
Julien Hillairet,
Patrick Mollard,
Yanping Zhao,
Jean-Michel Bernard,
Yuntao Song,
Arnaud Argouarch,
Gilles Berger-By,
Nicolas Charabot,
Gen Chen,
Zhaoxi Chen,
Laurent Colas,
Jean-Marc Delaplanche,
Pierre Dumortier,
Frédéric Durodié,
Annika Ekedahl,
Nicolas Fedorczak,
Fabien Ferlay,
Marc Goniche,
Jean-Claude Hatchressian,
Walid Helou,
Jonathan Jacquot,
Emmanuel Joffrin,
Xavier Litaudon,
Gilles Lombard,
Riccardo Maggiora
, et al. (11 additional authors not shown)
Abstract:
The design of the WEST (Tungsten-W Environment in Steady-state Tokamak) Ion cyclotron resonance heating antennas is based on a previously tested conjugate-T Resonant Double Loops prototype equipped with internal vacuum matching capacitors. The design and construction of three new WEST ICRH antennas are being carried out in close collaboration with ASIPP, within the framework of the Associated Labo…
▽ More
The design of the WEST (Tungsten-W Environment in Steady-state Tokamak) Ion cyclotron resonance heating antennas is based on a previously tested conjugate-T Resonant Double Loops prototype equipped with internal vacuum matching capacitors. The design and construction of three new WEST ICRH antennas are being carried out in close collaboration with ASIPP, within the framework of the Associated Laboratory in the fusion field between IRFM and ASIPP. The coupling performance to the plasma and the load-tolerance have been improved, while adding Continuous Wave operation capability by introducing water cooling in the entire antenna. On the generator side, the operation class of the high power tetrodes is changed from AB to B in order to allow high power operation (up to 3 MW per antenna) under higher VSWR (up to 2:1). Reliability of the generators is also improved by increasing the cavity breakdown voltage. The control and data acquisition system is also upgraded in order to resolve and react on fast events, such as ELMs. A new optical arc detection system comes in reinforcement of the V r /V f and SHAD systems.
△ Less
Submitted 4 March, 2016;
originally announced March 2016.
-
R&D activities on RF contacts for the ITER ion cyclotron resonance heating launcher
Authors:
Julien Hillairet,
Arnaud Argouarch,
Rob Bamber,
Bertrand Beaumont,
Jean-Michel Bernard,
Jean-Marc Delaplanche,
Frédéric Durodié,
Philippe Lamalle,
Gilles Lombard,
Keith Nicholls,
Mark Shannon,
Karl Vulliez,
Vincent Cantone,
Jean-Claude Hatchressian,
Philippe Lebourg,
André Martinez,
Patrick Mollard,
David Mouyon,
Marco Pagano,
Jean-Claude Patterlini,
Bernard Soler,
Didier Thouvenin,
Lionel Toulouse,
Jean-Marc Verger,
Terence Vigne
, et al. (1 additional authors not shown)
Abstract:
Embedded RF contacts are integrated within the ITER ICRH launcher to allow assembling, sliding and to lower the thermo-mechanical stress. They have to withstand a peak RF current up to 2.5 kA at 55 MHz in steady-state conditions, in the vacuum environment of themachine.The contacts have to sustain a temperature up to 250{\textdegree}Cduring several days in baking operations and have to be reliable…
▽ More
Embedded RF contacts are integrated within the ITER ICRH launcher to allow assembling, sliding and to lower the thermo-mechanical stress. They have to withstand a peak RF current up to 2.5 kA at 55 MHz in steady-state conditions, in the vacuum environment of themachine.The contacts have to sustain a temperature up to 250{\textdegree}Cduring several days in baking operations and have to be reliable during the whole life of the launcher without degradation. The RF contacts are critical components for the launcher performance and intensive R&D is therefore required, since no RF contactshave so far been qualified at these specifications. In order to test and validate the anticipated RF contacts in operational conditions, CEA has prepared a test platform consisting of a steady-state vacuum pumped RF resonator. In collaboration with ITER Organization and the CYCLE consortium (CYclotronCLuster for Europe), an R&D program has been conducted to develop RF contacts that meet the ITER ICRH launcher specifications. A design proposed by CYCLE consortium, using brazed lamellas supported by a spring to improve thermal exchange efficiency while guaranteeing high contact force, was tested successfully in the T-resonator up to 1.7 kA during 1200 s, but failed for larger current values due to a degradation of the contacts. Details concerning the manufacturing of the brazed contacts on its titanium holder, the RF tests results performed on the resonator and the non-destructive tests analysis of the contacts are given in this paper.
△ Less
Submitted 8 June, 2015;
originally announced June 2015.
-
Design and RF measurements of a 5 GHz 500 kW window for the ITER LHCD system
Authors:
Julien Hillairet,
J. Achard,
N. Dechambre,
L. Delpech,
A. Ekedahl,
N. Faure,
M. Goniche,
J. Kim,
S. Larroque,
R. Magne,
L. Marfisi,
W. Namkung,
H. Park,
S. Park,
S. Poli,
K. Vulliez
Abstract:
CEA/IRFM is conducting R\&D efforts in order to validate the critical RF components of the 5 GHz ITER LHCD system, which is expected to transmit 20 MW of RF power to the plasma. Two 5 GHz 500 kW BeO pill-box type window prototypes have been manufactured in 2012 by the PMB Company, in close collaboration with CEA/IRFM. Both windows have been validated at low power, showing good agreement between me…
▽ More
CEA/IRFM is conducting R\&D efforts in order to validate the critical RF components of the 5 GHz ITER LHCD system, which is expected to transmit 20 MW of RF power to the plasma. Two 5 GHz 500 kW BeO pill-box type window prototypes have been manufactured in 2012 by the PMB Company, in close collaboration with CEA/IRFM. Both windows have been validated at low power, showing good agreement between measured and modeling, with a return loss better than 32 dB and an insertion loss below 0.05 dB. This paper reports on the window RF design and the low power measurements. The high power tests up to 500kW have been carried out in March 2013 in collaboration with NFRI. Results of these tests are also reported. In the current ITER LHCD design, 20 MW Continuous Wave (CW) of Radio-Frequency power at 5 GHz are expected to be generated and transmitted to the plasma. In order to separate the vacuum vessel pressure from the cryostat waveguide pressure, forty eight 5 GHz 500kW CW windows are to be assembled on the waveguides at the equatorial port flange. For nuclear safety reasons, forty eight additional windows could be located in the cryostat section, to separate and monitor the cryostat waveguide pressure from the exterior transmission line pressure. These windows are identified as being one of the main critical components for the ITER LHCD system since first ITER LHCD studies [1] [2] [3] or more recently [4] [5] , and clearly require an important R\&D effort. In this context and even if the LHCD system is not part of the construction baseline, the CEA/IRFM is conducting a R\&D effort in order to validate a design and the performances of these RF windows. In order to begin the assessment of this need, two 5 GHz 500 kW/5 s pill-box type windows prototypes have been manufactured in 2012 by the PMB Company in close collaboration with the CEA/IRFM [6]. The section 2 of this paper reports the RF and mechanical design of a 5 GHz window. Some features of the mechanical design and the experimental RF measurements at low power are reported in section 3. High power results, made in collaboration with NFRI, are detailed in section 4. The development of CW windows is discussed in the conclusion. 2-RF AND MECHANICAL DESIGN The proposed 5 GHz RF window is based on a pill-box design [2] , i.e. a ceramic brazed in portion of a circular waveguide, connected on either side to a rectangular waveguide section. Typical design rules of thumb of such device are circular section diameter about the same size of the diagonal of the rectangular waveguide (cf. FIGURE 1). Without taking into account the ceramic, the circular section length is approximately half a guided wavelength of the circular TE 11 mode, in order for the device to act as a half-wave transformer. Once optimized, taking into account the ceramic, matching is correct only for a narrow band of frequency and is very sensitive to the device dimensions and the ceramic relative permittivity. The heat losses in the ceramic, which have to be extracted by an active water cooling, depends on the inside electric field topology and of ceramic dielectric loss (loss tangent). Undesirable modes due to parasitic resonances can be excited in the ceramic volume, raising the electric field and
△ Less
Submitted 17 March, 2015;
originally announced March 2015.
-
Lower Hybrid antennas for nuclear fusion experiments
Authors:
Julien Hillairet,
J. Achard,
Young-Soon Bae,
X. Bai,
C. Balorin,
Y. Baranov,
V. Basiuk,
A. Bécoulet,
J. Belo,
G. Berger-By,
S. Brémond,
C. Castaldo,
S. Ceccuzzi,
R. Cesario,
E. Corbel,
X. Courtois,
J. Decker,
E. Delmas,
L. Delpech,
X. Ding,
D. Douai,
A. Ekedahl,
C. Goletto,
M. Goniche,
D. Guilhem
, et al. (18 additional authors not shown)
Abstract:
The nuclear fusion research goal is to demonstrate the feasibility of fusion power for peaceful purposes. In order to achieve the conditions similar to those expected in an electricity-generating fusion power plant, plasmas with a temperature of several hundreds of millions of degrees must be generated and sustained for long periods. For this purpose, RF antennas delivering multi-megawatts of powe…
▽ More
The nuclear fusion research goal is to demonstrate the feasibility of fusion power for peaceful purposes. In order to achieve the conditions similar to those expected in an electricity-generating fusion power plant, plasmas with a temperature of several hundreds of millions of degrees must be generated and sustained for long periods. For this purpose, RF antennas delivering multi-megawatts of power to magnetized confined plasma are commonly used in experimental tokamaks. In the gigahertz range of frequencies, high power phased arrays known as "Lower Hybrid" (LH) antennas are used to extend the plasma duration. This paper reviews some of the technological aspects of the LH antennas used in the Tore Supra tokamak and presents the current design of a proposed 20 MW LH system for the international experiment ITER.
△ Less
Submitted 17 March, 2015;
originally announced March 2015.
-
Recent progress on lower hybrid current drive and implications for ITER
Authors:
Julien Hillairet,
A. Ekedahl,
M. Goniche,
J. Achard,
A. Armitano,
B. Beckett,
J. Belo,
G. Berger-By,
E. Corbel,
L. Delpech,
J. Decker,
R. Dumont,
D. Guilhem,
F. Kazarian,
X. Litaudon,
R. Magne,
L. Marfisi,
P. Mollard,
W. Namkung,
E. Nilsson,
S. Park,
Y. Peysson,
M. Preynas,
P. K. Sharma,
M. Prou
, et al. (1 additional authors not shown)
Abstract:
The sustainment of steady-state plasmas in tokamaks requires efficient current drive systems. Lower Hybrid Current Drive (LHCD) is currently the most efficient method to generate a continuous additional off-axis toroidal plasma current as well as reduce the poloidal flux consumption during the plasma current ramp-up phase. The operation of the Tore Supra ITER-like LH launcher has demonstrated the…
▽ More
The sustainment of steady-state plasmas in tokamaks requires efficient current drive systems. Lower Hybrid Current Drive (LHCD) is currently the most efficient method to generate a continuous additional off-axis toroidal plasma current as well as reduce the poloidal flux consumption during the plasma current ramp-up phase. The operation of the Tore Supra ITER-like LH launcher has demonstrated the capability to couple LH power at ITER-like power densities with very low reflected power during long pulses. In addition, the installation of eight 700kW/CW klystrons at the LH transmitter has allowed increasing the total LH power in long pulse scenarios. However, in order to achieve pure stationary LH sustained plasmas, some R\&D are needed to increase the reliability of all the systems and codes, from the RF sources to the plasma scenario prediction. The CEA/IRFM is addressing some of these issues by leading a R\&D program towards an ITER LH system and by the validation of an integrated LH modeling suite of codes. In 2011, the RF design of a mode converter has been validated at low power. A 500 kW/5 s RF window is currently under manufacturing and will be tested at high power in 2012 in collaboration with NFRI. All of this work aims to reduce the operational risks associated with the ITER steady-state operations.
△ Less
Submitted 17 March, 2015;
originally announced March 2015.
-
Design and Tests of 500kW RF Windows for the ITER LHCD System
Authors:
Julien Hillairet,
J Kim,
N Faure,
J Achard,
L Delpech,
M Goniche,
S Larroque,
R Magne,
L Marfisi,
S Park,
S Poli,
N Dechambre,
K Vulliez
Abstract:
In the frame of a R\&D effort conducted by CEA toward the design and the qualification of a 5 GHz LHCD system for the ITER tokamak, two 5 GHz 500 kW/5 s windows have been designed, manufactured and tested at high power in collaboration with the National Fusion Research Institute (NFRI). The window design rely on a symmetrical pill-box concept with a cylindrical beryllium oxide ceramic brazed on an…
▽ More
In the frame of a R\&D effort conducted by CEA toward the design and the qualification of a 5 GHz LHCD system for the ITER tokamak, two 5 GHz 500 kW/5 s windows have been designed, manufactured and tested at high power in collaboration with the National Fusion Research Institute (NFRI). The window design rely on a symmetrical pill-box concept with a cylindrical beryllium oxide ceramic brazed on an actively water cooled copper skirt. The ceramic RF properties have been measured on a test sample to get realistic values for guiding the design. Low power measurements of the manufactured windows show return losses below-32 dB and insertion losses between-0.01 dB and-0.05 dB, with an optimum frequency shifted toward lower frequencies. High power tests conducted at NFRI show unexpected total power loss for both windows. The ceramic temperature during RF pulses has been found to reach unexpected high temperature, preventing these windows to be used under CW conditions. A post-mortem RF analysis of samples taken from one window shows that the dielectric properties of the ceramic were not the ones measured on the manufacturer sample, which partly explain the differences with the reference modelling.
△ Less
Submitted 17 March, 2015;
originally announced March 2015.
