-
Thermal Cycling Reliability of Hybrid Pixel Sensor Modules for The ATLAS High Granularity Timing Detector
Authors:
Y. Li,
A. Aboulhorma,
M. Ait Tamlihat,
H. M. Alfanda,
N. Atanov,
O. Atanova,
I. Azzouzi,
J. Barreiro Guimarães Da Costa,
T. Beau,
D. Benchekroun,
F. Bendebba,
Y. Bimgdi,
A. Blot,
A. Boikov,
J. Bonis,
D. Boumediene,
C. Brito,
A. S. Brogna,
A. M. Burger,
L. Cadamuro,
Y. Cai,
N. Cartalade,
R. Casanova Mohr,
Y. Che,
X. Chen
, et al. (203 additional authors not shown)
Abstract:
The reliability of bump connection structures has become a critical aspect of future silicon detectors for particle physics. The High Granularity Timing Detector (HGTD) for the ATLAS experiment at the High-Luminosity Large Hadron Collider will require 8032 hybrid pixel sensor modules, composed of two Low Gain Avalanche Diode sensors bump-bonded to two readout ASICs and glued to a passive PCB. The…
▽ More
The reliability of bump connection structures has become a critical aspect of future silicon detectors for particle physics. The High Granularity Timing Detector (HGTD) for the ATLAS experiment at the High-Luminosity Large Hadron Collider will require 8032 hybrid pixel sensor modules, composed of two Low Gain Avalanche Diode sensors bump-bonded to two readout ASICs and glued to a passive PCB. The detector will operate at low temperature (-30 degrees Celsius) to mitigate the impact of irradiation. The thermomechanical reliability of flip-chip bump connections in HGTD modules is a critical concern, particularly due to their characteristically lower bump density (pixel pitch dimensions of 1.3 mm by 1.3 mm). This paper elaborates on the challenges arising from this design characteristic. Finite element analysis and experimental testing were employed to investigate failure modes in the flip-chip bump structures under thermal cycling from -45 degrees Celsius to 40 degrees Celsius and to guide the module redesign. The optimized design demonstrates significantly enhanced robustness and is projected to fulfill the full lifetime requirements of the HGTD.
△ Less
Submitted 17 September, 2025;
originally announced September 2025.
-
Development of non amplified Depleted MAPS sensors towards 50 ps timing resolution on charged particles
Authors:
Raimon Casanova,
Yavuz Degerli,
Yujing Gan,
Sebastian Grinstein,
Fabrice Guilloux,
Tomasz Hemperek,
G. Huang,
Jean-Pierre Meyer,
Philippe Schwemling
Abstract:
The MiniCactus sensors are demonstrator sensors designed in LFoundry LF15A 150 nm technology, intended to study the performance of non amplified High Voltage High Resistivity CMOS sensors for measurement of time of arrival of charged particles. This paper presents the context, design features and some of the first test-beam results obtained with the latest MiniCactus sensor version, MiniCactus V2.…
▽ More
The MiniCactus sensors are demonstrator sensors designed in LFoundry LF15A 150 nm technology, intended to study the performance of non amplified High Voltage High Resistivity CMOS sensors for measurement of time of arrival of charged particles. This paper presents the context, design features and some of the first test-beam results obtained with the latest MiniCactus sensor version, MiniCactus V2. With a 175 micron thick sensor biased at -350 V, we have obtained a 60 ps time resolution on Minimum Ionizing Particles detected with a 500 micron by 500 micron pixel.
△ Less
Submitted 16 June, 2025;
originally announced June 2025.
-
SALSA: a new versatile readout chip for MPGD detectors
Authors:
D. Neyret,
P. Baron,
F. Bouyjou,
M. Bregant,
S. Chevobbe,
Y. Degerli,
C. Flouzat,
O. Gevin,
F. Guilloux,
H. Hernandez,
I. Mandjavidze,
M. Munhoz,
B. Sanches,
L. Severo,
J. N. Soares,
W. Van Noije,
F. William da Costa
Abstract:
The SALSA chip is a future readout ASIC foreseen for the MPGD detectors, developed in the framework of the EIC collider project, to equip the MPGD trackers of the EPIC experiment. It is designed to be versatile, to be adapted to other usages of MPGD detectors like TPC or photon detectors. It integrates a frontend block and an ADC for each of the 64 channels, associated to a configurable DSP proces…
▽ More
The SALSA chip is a future readout ASIC foreseen for the MPGD detectors, developed in the framework of the EIC collider project, to equip the MPGD trackers of the EPIC experiment. It is designed to be versatile, to be adapted to other usages of MPGD detectors like TPC or photon detectors. It integrates a frontend block and an ADC for each of the 64 channels, associated to a configurable DSP processor meant to correct data and reduce the raw data flux to limit the output bandwidth. It will be compatible with the continuous readout foreseen for the EPIC DAQ, but will also work in a triggered environment. Several prototypes are already produced in order to qualify the different blocks of the chip, in particular the frontend, the ADC and the clock generation. The next 32-channel prototype is currently under development and is planed to be produced in 2025. The final prototype will be produced and tested from 2026 for a production of the SALSA chip at the horizon of 2027. Keywords: Micro-patterned Gaseous Detectors (MPGD), Readout electronics, Readout ASIC, Data processing, EIC project, EPIC experiment
△ Less
Submitted 25 June, 2025; v1 submitted 17 January, 2025;
originally announced January 2025.
-
Using graph neural networks to reconstruct charged pion showers in the CMS High Granularity Calorimeter
Authors:
M. Aamir,
G. Adamov,
T. Adams,
C. Adloff,
S. Afanasiev,
C. Agrawal,
C. Agrawal,
A. Ahmad,
H. A. Ahmed,
S. Akbar,
N. Akchurin,
B. Akgul,
B. Akgun,
R. O. Akpinar,
E. Aktas,
A. Al Kadhim,
V. Alexakhin,
J. Alimena,
J. Alison,
A. Alpana,
W. Alshehri,
P. Alvarez Dominguez,
M. Alyari,
C. Amendola,
R. B. Amir
, et al. (550 additional authors not shown)
Abstract:
A novel method to reconstruct the energy of hadronic showers in the CMS High Granularity Calorimeter (HGCAL) is presented. The HGCAL is a sampling calorimeter with very fine transverse and longitudinal granularity. The active media are silicon sensors and scintillator tiles readout by SiPMs and the absorbers are a combination of lead and Cu/CuW in the electromagnetic section, and steel in the hadr…
▽ More
A novel method to reconstruct the energy of hadronic showers in the CMS High Granularity Calorimeter (HGCAL) is presented. The HGCAL is a sampling calorimeter with very fine transverse and longitudinal granularity. The active media are silicon sensors and scintillator tiles readout by SiPMs and the absorbers are a combination of lead and Cu/CuW in the electromagnetic section, and steel in the hadronic section. The shower reconstruction method is based on graph neural networks and it makes use of a dynamic reduction network architecture. It is shown that the algorithm is able to capture and mitigate the main effects that normally hinder the reconstruction of hadronic showers using classical reconstruction methods, by compensating for fluctuations in the multiplicity, energy, and spatial distributions of the shower's constituents. The performance of the algorithm is evaluated using test beam data collected in 2018 prototype of the CMS HGCAL accompanied by a section of the CALICE AHCAL prototype. The capability of the method to mitigate the impact of energy leakage from the calorimeter is also demonstrated.
△ Less
Submitted 18 December, 2024; v1 submitted 17 June, 2024;
originally announced June 2024.
-
MiniCACTUS: A 65 ps Time Resolution Depleted Monolithic CMOS Sensor
Authors:
Yavuz Degerli,
Fabrice Guilloux,
Tomasz Hemperek,
Jean-Pierre Meyer,
Philippe Schwemling
Abstract:
MiniCACTUS is a monolithic sensor prototype optimised for timing measurement of charged particles. It has been designed in a standard 150 nm CMOS process without dedicated amplification layer. It is intended as a demonstrator chip for future large scale timing detectors, like upgrades of timing detectors at LHC, or future high energy physics detector projects. The sensor features an active array o…
▽ More
MiniCACTUS is a monolithic sensor prototype optimised for timing measurement of charged particles. It has been designed in a standard 150 nm CMOS process without dedicated amplification layer. It is intended as a demonstrator chip for future large scale timing detectors, like upgrades of timing detectors at LHC, or future high energy physics detector projects. The sensor features an active array of 2 x 4 diodes, analog and digital Front-Ends (FEs), a slow control interface, and bias circuitry programmable through internal DACs. The sensing element is a deep n-well/p-substrate diode. Thanks to the optimized guard-rings surrounding the whole chip, it is possible to apply safely more than 450 V on the high-resistivity substrate allowing fast charge collection. The baseline pixel dimensions are 1.0 mm x 1.0 mm and 0.5 mm x 1.0 mm. The analog FEs and the discriminators for each pixel are implemented outside the pixel, at the column level. The power consumption is approximately 300 mW/cm$\mathbf {^2}$, which is compatible with cooling infrastructure available at LHC experiments, and making integration of this concept viable in future high energy physics experiments. After fabrication, the sensors have been thinned to 100 $μ$m, 200 $μ$m and 300 $μ$m total thickness and then post-processed for backside biasing. The time resolution of several sensors with different thicknesses has been measured in 3 test-beam campaigns using high energy muons (Minimum Ionizing Particles) at CERN SPS in 2021 and 2022. A resolution of 65.3 ps has been measured with on-chip FE and discriminator. This paper will focus on the results of these test-beam campaigns.
△ Less
Submitted 15 September, 2023;
originally announced September 2023.
-
Performance of the CMS High Granularity Calorimeter prototype to charged pion beams of 20$-$300 GeV/c
Authors:
B. Acar,
G. Adamov,
C. Adloff,
S. Afanasiev,
N. Akchurin,
B. Akgün,
M. Alhusseini,
J. Alison,
J. P. Figueiredo de sa Sousa de Almeida,
P. G. Dias de Almeida,
A. Alpana,
M. Alyari,
I. Andreev,
U. Aras,
P. Aspell,
I. O. Atakisi,
O. Bach,
A. Baden,
G. Bakas,
A. Bakshi,
S. Banerjee,
P. DeBarbaro,
P. Bargassa,
D. Barney,
F. Beaudette
, et al. (435 additional authors not shown)
Abstract:
The upgrade of the CMS experiment for the high luminosity operation of the LHC comprises the replacement of the current endcap calorimeter by a high granularity sampling calorimeter (HGCAL). The electromagnetic section of the HGCAL is based on silicon sensors interspersed between lead and copper (or copper tungsten) absorbers. The hadronic section uses layers of stainless steel as an absorbing med…
▽ More
The upgrade of the CMS experiment for the high luminosity operation of the LHC comprises the replacement of the current endcap calorimeter by a high granularity sampling calorimeter (HGCAL). The electromagnetic section of the HGCAL is based on silicon sensors interspersed between lead and copper (or copper tungsten) absorbers. The hadronic section uses layers of stainless steel as an absorbing medium and silicon sensors as an active medium in the regions of high radiation exposure, and scintillator tiles directly readout by silicon photomultipliers in the remaining regions. As part of the development of the detector and its readout electronic components, a section of a silicon-based HGCAL prototype detector along with a section of the CALICE AHCAL prototype was exposed to muons, electrons and charged pions in beam test experiments at the H2 beamline at the CERN SPS in October 2018. The AHCAL uses the same technology as foreseen for the HGCAL but with much finer longitudinal segmentation. The performance of the calorimeters in terms of energy response and resolution, longitudinal and transverse shower profiles is studied using negatively charged pions, and is compared to GEANT4 predictions. This is the first report summarizing results of hadronic showers measured by the HGCAL prototype using beam test data.
△ Less
Submitted 27 May, 2023; v1 submitted 9 November, 2022;
originally announced November 2022.
-
Response of a CMS HGCAL silicon-pad electromagnetic calorimeter prototype to 20-300 GeV positrons
Authors:
B. Acar,
G. Adamov,
C. Adloff,
S. Afanasiev,
N. Akchurin,
B. Akgün,
F. Alam Khan,
M. Alhusseini,
J. Alison,
A. Alpana,
G. Altopp,
M. Alyari,
S. An,
S. Anagul,
I. Andreev,
P. Aspell,
I. O. Atakisi,
O. Bach,
A. Baden,
G. Bakas,
A. Bakshi,
S. Bannerjee,
P. Bargassa,
D. Barney,
F. Beaudette
, et al. (364 additional authors not shown)
Abstract:
The Compact Muon Solenoid Collaboration is designing a new high-granularity endcap calorimeter, HGCAL, to be installed later this decade. As part of this development work, a prototype system was built, with an electromagnetic section consisting of 14 double-sided structures, providing 28 sampling layers. Each sampling layer has an hexagonal module, where a multipad large-area silicon sensor is glu…
▽ More
The Compact Muon Solenoid Collaboration is designing a new high-granularity endcap calorimeter, HGCAL, to be installed later this decade. As part of this development work, a prototype system was built, with an electromagnetic section consisting of 14 double-sided structures, providing 28 sampling layers. Each sampling layer has an hexagonal module, where a multipad large-area silicon sensor is glued between an electronics circuit board and a metal baseplate. The sensor pads of approximately 1 cm$^2$ are wire-bonded to the circuit board and are readout by custom integrated circuits. The prototype was extensively tested with beams at CERN's Super Proton Synchrotron in 2018. Based on the data collected with beams of positrons, with energies ranging from 20 to 300 GeV, measurements of the energy resolution and linearity, the position and angular resolutions, and the shower shapes are presented and compared to a detailed Geant4 simulation.
△ Less
Submitted 31 March, 2022; v1 submitted 12 November, 2021;
originally announced November 2021.
-
Test beam characterization of sensor prototypes for the CMS Barrel MIP Timing Detector
Authors:
R. Abbott,
A. Abreu,
F. Addesa,
M. Alhusseini,
T. Anderson,
Y. Andreev,
A. Apresyan,
R. Arcidiacono,
M. Arenton,
E. Auffray,
D. Bastos,
L. A. T. Bauerdick,
R. Bellan,
M. Bellato,
A. Benaglia,
M. Benettoni,
R. Bertoni,
M. Besancon,
S. Bharthuar,
A. Bornheim,
E. Brücken,
J. N. Butler,
C. Campagnari,
M. Campana,
R. Carlin
, et al. (174 additional authors not shown)
Abstract:
The MIP Timing Detector will provide additional timing capabilities for detection of minimum ionizing particles (MIPs) at CMS during the High Luminosity LHC era, improving event reconstruction and pileup rejection. The central portion of the detector, the Barrel Timing Layer (BTL), will be instrumented with LYSO:Ce crystals and Silicon Photomultipliers (SiPMs) providing a time resolution of about…
▽ More
The MIP Timing Detector will provide additional timing capabilities for detection of minimum ionizing particles (MIPs) at CMS during the High Luminosity LHC era, improving event reconstruction and pileup rejection. The central portion of the detector, the Barrel Timing Layer (BTL), will be instrumented with LYSO:Ce crystals and Silicon Photomultipliers (SiPMs) providing a time resolution of about 30 ps at the beginning of operation, and degrading to 50-60 ps at the end of the detector lifetime as a result of radiation damage. In this work, we present the results obtained using a 120 GeV proton beam at the Fermilab Test Beam Facility to measure the time resolution of unirradiated sensors. A proof-of-concept of the sensor layout proposed for the barrel region of the MTD, consisting of elongated crystal bars with dimensions of about 3 x 3 x 57 mm$^3$ and with double-ended SiPM readout, is demonstrated. This design provides a robust time measurement independent of the impact point of the MIP along the crystal bar. We tested LYSO:Ce bars of different thickness (2, 3, 4 mm) with a geometry close to the reference design and coupled to SiPMs manufactured by Hamamatsu and Fondazione Bruno Kessler. The various aspects influencing the timing performance such as the crystal thickness, properties of the SiPMs (e.g. photon detection efficiency), and impact angle of the MIP are studied. A time resolution of about 28 ps is measured for MIPs crossing a 3 mm thick crystal bar, corresponding to an MPV energy deposition of 2.6 MeV, and of 22 ps for the 4.2 MeV MPV energy deposition expected in the BTL, matching the detector performance target for unirradiated devices.
△ Less
Submitted 16 July, 2021; v1 submitted 15 April, 2021;
originally announced April 2021.
-
Construction and commissioning of CMS CE prototype silicon modules
Authors:
B. Acar,
G. Adamov,
C. Adloff,
S. Afanasiev,
N. Akchurin,
B. Akgün,
M. Alhusseini,
J. Alison,
G. Altopp,
M. Alyari,
S. An,
S. Anagul,
I. Andreev,
M. Andrews,
P. Aspell,
I. A. Atakisi,
O. Bach,
A. Baden,
G. Bakas,
A. Bakshi,
P. Bargassa,
D. Barney,
E. Becheva,
P. Behera,
A. Belloni
, et al. (307 additional authors not shown)
Abstract:
As part of its HL-LHC upgrade program, the CMS Collaboration is developing a High Granularity Calorimeter (CE) to replace the existing endcap calorimeters. The CE is a sampling calorimeter with unprecedented transverse and longitudinal readout for both electromagnetic (CE-E) and hadronic (CE-H) compartments. The calorimeter will be built with $\sim$30,000 hexagonal silicon modules. Prototype modul…
▽ More
As part of its HL-LHC upgrade program, the CMS Collaboration is developing a High Granularity Calorimeter (CE) to replace the existing endcap calorimeters. The CE is a sampling calorimeter with unprecedented transverse and longitudinal readout for both electromagnetic (CE-E) and hadronic (CE-H) compartments. The calorimeter will be built with $\sim$30,000 hexagonal silicon modules. Prototype modules have been constructed with 6-inch hexagonal silicon sensors with cell areas of 1.1~$cm^2$, and the SKIROC2-CMS readout ASIC. Beam tests of different sampling configurations were conducted with the prototype modules at DESY and CERN in 2017 and 2018. This paper describes the construction and commissioning of the CE calorimeter prototype, the silicon modules used in the construction, their basic performance, and the methods used for their calibration.
△ Less
Submitted 10 December, 2020;
originally announced December 2020.
-
The DAQ system of the 12,000 Channel CMS High Granularity Calorimeter Prototype
Authors:
B. Acar,
G. Adamov,
C. Adloff,
S. Afanasiev,
N. Akchurin,
B. Akgün,
M. Alhusseini,
J. Alison,
G. Altopp,
M. Alyari,
S. An,
S. Anagul,
I. Andreev,
M. Andrews,
P. Aspell,
I. A. Atakisi,
O. Bach,
A. Baden,
G. Bakas,
A. Bakshi,
P. Bargassa,
D. Barney,
E. Becheva,
P. Behera,
A. Belloni
, et al. (307 additional authors not shown)
Abstract:
The CMS experiment at the CERN LHC will be upgraded to accommodate the 5-fold increase in the instantaneous luminosity expected at the High-Luminosity LHC (HL-LHC). Concomitant with this increase will be an increase in the number of interactions in each bunch crossing and a significant increase in the total ionising dose and fluence. One part of this upgrade is the replacement of the current endca…
▽ More
The CMS experiment at the CERN LHC will be upgraded to accommodate the 5-fold increase in the instantaneous luminosity expected at the High-Luminosity LHC (HL-LHC). Concomitant with this increase will be an increase in the number of interactions in each bunch crossing and a significant increase in the total ionising dose and fluence. One part of this upgrade is the replacement of the current endcap calorimeters with a high granularity sampling calorimeter equipped with silicon sensors, designed to manage the high collision rates. As part of the development of this calorimeter, a series of beam tests have been conducted with different sampling configurations using prototype segmented silicon detectors. In the most recent of these tests, conducted in late 2018 at the CERN SPS, the performance of a prototype calorimeter equipped with ${\approx}12,000\rm{~channels}$ of silicon sensors was studied with beams of high-energy electrons, pions and muons. This paper describes the custom-built scalable data acquisition system that was built with readily available FPGA mezzanines and low-cost Raspberry PI computers.
△ Less
Submitted 8 December, 2020; v1 submitted 7 December, 2020;
originally announced December 2020.
-
DMAPS Monopix developments in large and small electrode designs
Authors:
Christian Bespin,
Marlon Barbero,
Pierre Barrillon,
Ivan Berdalovic,
Siddharth Bhat,
Patrick Breugnon,
Ivan Caicedo,
Roberto Cardella,
Zongde Chen,
Yavuz Degerli,
Jochen Dingfelder,
Leyre Flores Sanz de Acedo,
Stephanie Godiot,
Fabrice Guilloux,
Toko Hirono,
Tomasz Hemperek,
Fabian Hügging,
Hans Krüger,
Thanushan Kugathasan,
Cesar Augusto Marin Tobon,
Konstantinos Moustakas,
Patrick Pangaud,
Heinz Pernegger,
Francesco Piro,
Petra Riedler
, et al. (8 additional authors not shown)
Abstract:
LF-Monopix1 and TJ-Monopix1 are depleted monolithic active pixel sensors (DMAPS) in 150 nm LFoundry and 180 nm TowerJazz CMOS technologies respectively. They are designed for usage in high-rate and high-radiation environments such as the ATLAS Inner Tracker at the High-Luminosity Large Hadron Collider (HL-LHC). Both chips are read out using a column-drain readout architecture. LF-Monopix1 follows…
▽ More
LF-Monopix1 and TJ-Monopix1 are depleted monolithic active pixel sensors (DMAPS) in 150 nm LFoundry and 180 nm TowerJazz CMOS technologies respectively. They are designed for usage in high-rate and high-radiation environments such as the ATLAS Inner Tracker at the High-Luminosity Large Hadron Collider (HL-LHC). Both chips are read out using a column-drain readout architecture. LF-Monopix1 follows a design with large charge collection electrode where readout electronics are placed inside. Generally, this offers a homogeneous electrical field in the sensor and short drift distances. TJ-Monopix1 employs a small charge collection electrode with readout electronics separated from the electrode and an additional n-type implant to achieve full depletion of the sensitive volume. This approach offers a low sensor capacitance and therefore low noise and is typically implemented with small pixel size. Both detectors have been characterized before and after irradiation using lab tests and particle beams.
△ Less
Submitted 9 July, 2020; v1 submitted 3 June, 2020;
originally announced June 2020.
-
CACTUS: A depleted monolithic active timing sensor using a CMOS radiation hard technology
Authors:
Yavuz Degerli,
Fabrice Guilloux,
Claude Guyot,
Jean-Pierre Meyer,
Ahmimed Ouraou,
Philippe Schwemling,
Artur Apresyan,
Ryan E. Heller,
Mohd Meraj,
Christian Pena,
Si Xie,
Tomasz Hemperek
Abstract:
The planned luminosity increase at the Large Hadron Collider in the coming years has triggered interest in the use of the particles' time of arrival as additional information in specialized detectors to mitigate the impact of pile-up. The required time resolution is of the order of tens of picoseconds, with a spatial granularity of the order of 1 mm. A time measurement at this precision level will…
▽ More
The planned luminosity increase at the Large Hadron Collider in the coming years has triggered interest in the use of the particles' time of arrival as additional information in specialized detectors to mitigate the impact of pile-up. The required time resolution is of the order of tens of picoseconds, with a spatial granularity of the order of 1 mm. A time measurement at this precision level will also be of interest beyond the LHC and beyond high energy particle physics. We present in this paper the first developments towards a radiation hard Depleted Monolithic Active Pixel Sensor (DMAPS), with high-resolution time measurement capability. The technology chosen is a standard high voltage CMOS process, in conjunction with a high resistivity detector material, which has already proven to efficiently detect particles in tracking applications after several hundred of Mrad of irradiation.
△ Less
Submitted 6 May, 2020; v1 submitted 9 March, 2020;
originally announced March 2020.
-
Radiation hard DMAPS pixel sensors in 150nm CMOS technology for operation at LHC
Authors:
M. Barbero,
P. Barrillon,
C. Bespin,
S. Bhat,
P. Breugnon,
I. Caicedo,
Z. Chen,
Y. Degerli,
J. Dingfelder,
S. Godiot,
F. Guilloux,
T. Hemperek,
T. Hirono,
F. Hügging,
H. Krüger,
K. Moustakas,
A. Ouraou,
P. Pangaud,
I. Peric,
D-L. Pohl,
P. Rymaszewski,
P. Schwemling,
M. Vandenbroucke,
T. Wang,
N. Wermes
Abstract:
Monolithic Active Pixel Sensors (MAPS) have been developed since the late 1990s employing silicon substrate with a thin epitaxial layer in which deposited charge is collected by disordered diffusion rather than by drift in an electric field. As a consequence the signal is small and slow, and the radiation tolerance is below the requirements for LHC experiments by factors of 100 to 1000. We develop…
▽ More
Monolithic Active Pixel Sensors (MAPS) have been developed since the late 1990s employing silicon substrate with a thin epitaxial layer in which deposited charge is collected by disordered diffusion rather than by drift in an electric field. As a consequence the signal is small and slow, and the radiation tolerance is below the requirements for LHC experiments by factors of 100 to 1000. We developed fully depleted (D)MAPS pixel sensors employing a 150 nm CMOS technology and using a high resistivity substrate as well as a high biasing voltage. The development has been carried out in three subsequent iterations, from prototypes to a large pixel matrix comprising a complete readout architecture suitable for LHC operation. Full CMOS electronics is embedded in large deep n-wells which at the same time serve as collection nodes (large electrode design). The devices have been intensively characterized before and after irradiation employing lab tests as well as particle beams. The devices can cope with particle rates seen by the innermost pixel detectors of the LHC pp-experiments or as seen by the outer pixel layers of the planned HL-LHC upgrade. They are radiation hard to particle fluences of at least $10^{15}~\mathrm{n_{eq}/cm^2}$ and total ionization doses of at least 50 Mrad.
△ Less
Submitted 25 May, 2020; v1 submitted 4 November, 2019;
originally announced November 2019.
-
The Monopix chips: Depleted monolithic active pixel sensors with a column-drain read-out architecture for the ATLAS Inner Tracker upgrade
Authors:
Ivan Caicedo,
Marlon Barbero,
Pierre Barrillon,
Ivan Berdalovic,
Siddharth Bhat,
Christian Bespin,
Patrick Breugnon,
Roberto Cardella,
Zongde Chen,
Yavuz Degerli,
Jochen Dingfelder,
Stephanie Godiot,
Fabrice Guilloux,
Toko Hirono,
Tomasz Hemperek,
Fabian Hügging,
Hans Krüger,
Thanushan Kugathasan,
Konstantinos Moustakas,
Patrick Pangaud,
Heinz Pernegger,
David-Leon Pohl,
Petra Riedler,
Alexandre Rozanov,
Piotr Rymaszewski
, et al. (5 additional authors not shown)
Abstract:
Two different depleted monolithic CMOS active pixel sensor (DMAPS) prototypes with a fully synchronous column-drain read-out architecture were designed and tested: LF-Monopix and TJ-Monopix. These chips are part of a R&D effort towards a suitable implementation of a CMOS DMAPS for the HL-LHC ATLAS Inner Tracker. LF-Monopix was developed using a 150nm CMOS process on a highly resistive substrate (>…
▽ More
Two different depleted monolithic CMOS active pixel sensor (DMAPS) prototypes with a fully synchronous column-drain read-out architecture were designed and tested: LF-Monopix and TJ-Monopix. These chips are part of a R&D effort towards a suitable implementation of a CMOS DMAPS for the HL-LHC ATLAS Inner Tracker. LF-Monopix was developed using a 150nm CMOS process on a highly resistive substrate (>2 k$Ω\,$cm), while TJ-Monopix was fabricated using a modified 180 nm CMOS process with a 1 k$Ω\,$cm epi-layer for depletion. The chips differ in their front-end design, biasing scheme, pixel pitch, dimensions of the collecting electrode relative to the pixel size (large and small electrode design, respectively) and the placement of read-out electronics within such electrode. Both chips were operational after thinning down to 100 $\mathrmμ$m and additional back-side processing in LF-Monopix for total bulk depletion. The results in this work include measurements of their leakage current, noise, threshold dispersion, response to minimum ionizing particles and efficiency in test beam campaigns. In addition, the outcome from measurements after irradiation with neutrons up to a dose of $1\times10^{15}\,\mathrm{n_{eq} / cm}^{2}$ and its implications for future designs are discussed.
△ Less
Submitted 25 April, 2019; v1 submitted 10 February, 2019;
originally announced February 2019.
-
CMOS Monolithic Pixel Sensors based on the Column-Drain Architecture for the HL-LHC Upgrade
Authors:
K. Moustakas,
M. Barbero,
I. Berdalovic,
C. Bespin,
P. Breugnon,
I. Caicedo,
R. Cardella,
Y. Degerli,
N. Egidos Plaja,
S. Godiot,
F. Guilloux,
T. Hemperek,
T. Hirono,
H. Krueger,
T. Kugathasan,
C. A. Marin Tobon,
P. Pangaud,
H. Pernegger,
E. J. Schioppa,
W. Snoeys,
M. Vandenbroucke,
T. Wang,
N. Wermes
Abstract:
Depleted Monolithic Active Pixel Sensors (DMAPS) constitute a promising low cost alternative for the outer layers of the ATLAS experiment Inner Tracker (ITk). Realizations in modern, high resistivity CMOS technologies enhance their radiation tolerance by achieving substantial depletion of the sensing volume. Two DMAPS prototypes that use the same "column-drain" readout architecture and are based o…
▽ More
Depleted Monolithic Active Pixel Sensors (DMAPS) constitute a promising low cost alternative for the outer layers of the ATLAS experiment Inner Tracker (ITk). Realizations in modern, high resistivity CMOS technologies enhance their radiation tolerance by achieving substantial depletion of the sensing volume. Two DMAPS prototypes that use the same "column-drain" readout architecture and are based on different sensor implementation concepts named LF-Monopix and TJ-Monopix have been developed for the High Luminosity upgrade of the Large Hardon Collider (HL-LHC).
LF-Monopix was fabricated in the LFoundry 150 nm technology and features pixel size of $50x250~μm^{2}$ and large collection electrode opted for high radiation tolerance. Detection efficiency up to 99\% has been measured after irradiation to $1\cdot10^{15}~n_{eq}/cm^{2}$. TJ-Monopix is a large scale $(1x2~cm^{2})$ prototype featuring pixels of $36x40~μm^{2}$ size. It was fabricated in a novel TowerJazz 180 nm modified process that enables full depletion of the sensitive layer, while employing a small collection electrode that is less sensitive to crosstalk. The resulting small sensor capacitance ($<=3~fF$) is exploited by a compact, low power front end optimized to meet the 25ns timing requirement. Measurement results demonstrate the sensor performance in terms of Equivalent Noise Charge (ENC) $\approx11e^{-}$, threshold $\approx300~e^-$, threshold dispersion $\approx30~e^-$ and total power consumption lower than $120~mW/cm^2$.
△ Less
Submitted 10 September, 2018;
originally announced September 2018.
-
Characterization of a depleted monolithic pixel sensors in 150 nm CMOS technology for the ATLAS Inner Tracker upgrade
Authors:
F. J. Iguaz,
F. Balli,
M. Barbero,
S. Bhat,
P. Breugnon,
I. Caicedo,
Z. Chen,
Y. Degerli,
S. Godiot,
F. Guilloux,
C. Guyot,
T. Hemperek,
T. Hirono,
H. Krüger,
J. P. Meyer,
A. Ouraou,
P. Pangaud,
P. Rymaszewski,
P. Schwemling,
M. Vandenbroucke,
T. Wang,
N. Wermes
Abstract:
This work presents a depleted monolithic active pixel sensor (DMAPS) prototype manufactured in the LFoundry 150\,nm CMOS process. DMAPS exploit high voltage and/or high resistivity inclusion of modern CMOS technologies to achieve substantial depletion in the sensing volume. The described device, named LF-Monopix, was designed as a proof of concept of a fully monolithic sensor capable of operating…
▽ More
This work presents a depleted monolithic active pixel sensor (DMAPS) prototype manufactured in the LFoundry 150\,nm CMOS process. DMAPS exploit high voltage and/or high resistivity inclusion of modern CMOS technologies to achieve substantial depletion in the sensing volume. The described device, named LF-Monopix, was designed as a proof of concept of a fully monolithic sensor capable of operating in the environment of outer layers of the ATLAS Inner Tracker upgrade in 2025 for the High Luminosity Large Hadron Collider (HL-LHC). This type of devices has a lower production cost and lower material budget compared to presently used hybrid designs. In this work, the chip architecture will be described followed by the characterization of the different pre-amplifier and discriminator flavors with an external injection signal and an iron source (5.9\,keV x-rays).
△ Less
Submitted 12 June, 2018;
originally announced June 2018.
-
Depleted Fully Monolithic Active CMOS Pixel Sensors (DMAPS) in High Resistivity 150~nm Technology for LHC
Authors:
Toko Hirono,
Marlon Barbero,
Pierre Barrillon,
Siddharth Bhat,
Patrick Breugnon,
Ivan Caicedo,
Zongde Chen,
Michael Daas,
Yavuz Degerli,
Fabrice Guilloux,
Tomasz Hemperek,
Fabian Hugging,
Hans Kruger,
Patrick Pangaud,
Piotr Rymaszewski,
Philippe Schwemling,
Maxence Vandenbroucke,
Tianyang Wang,
Norbert Wermes
Abstract:
Depleted monolithic CMOS active pixel sensors (DMAPS) have been developed in order to demonstrate their suitability as pixel detectors in the outer layers of a toroidal LHC apparatus inner tracker (ATLAS ITk) pixel detector in the high-luminosity large hadron collider (HL-LHC). Two prototypes have been fabricated using 150 nm CMOS technology on high resistivity (> 2 k$Ω$ $cm^2$) wafers. The chip s…
▽ More
Depleted monolithic CMOS active pixel sensors (DMAPS) have been developed in order to demonstrate their suitability as pixel detectors in the outer layers of a toroidal LHC apparatus inner tracker (ATLAS ITk) pixel detector in the high-luminosity large hadron collider (HL-LHC). Two prototypes have been fabricated using 150 nm CMOS technology on high resistivity (> 2 k$Ω$ $cm^2$) wafers. The chip size is equivalent to that of the current ATLAS pixel detector readout chip. One of the prototypes is used for detailed characterization of the sensor and the analog readout of the DMAPS. The other is a fully monolithic DMAPS including fast readout digital logic that handles the required hit rate. In order to yield a strong homogeneous electric field within the sensor volume, thinning of the wafer was tested. The prototypes were irradiated with X-ray up to a total ionization dose (TID) of 50 Mrad and with neutrons up to non-ionizing energy loss (NIEL) of $10^{15}$ $n_{eq}/cm^2$. The analog readout circuitry maintained its performance after TID irradiation, and the hit-efficiency at > $10^7$ noise occupancy was as high as 98.9 % after NIEL irradiation.
△ Less
Submitted 25 March, 2018;
originally announced March 2018.
-
Development of depleted monolithic pixel sensors in 150 nm CMOS technology for the ATLAS Inner Tracker upgrade
Authors:
Piotr Rymaszewski,
Marlon Barbero,
Siddharth Bhat,
Patrick Breugnon,
Ivan Caicedo,
Zongde Chen,
Yavuz Degerli,
Stephanie Godiot,
Fabrice Guilloux,
Claude Guyot,
Tomasz Hemperek,
Toko Hirono,
Fabian Hügging,
Hans Krüger,
Mohamed Lachkar,
Patrick Pangaud,
Alexandre Rozanov,
Philippe Schwemling,
Maxence Vandenbroucke,
Tianyang Wang,
Norbert Wermes
Abstract:
This work presents a depleted monolithic active pixel sensor (DMAPS) prototype manufactured in the LFoundry 150 nm CMOS process. The described device, named LF-Monopix, was designed as a proof of concept of a fully monolithic sensor capable of operating in the environment of outer layers of the ATLAS Inner Tracker upgrade for the High Luminosity Large Hadron Collider (HL-LHC). Implementing such a…
▽ More
This work presents a depleted monolithic active pixel sensor (DMAPS) prototype manufactured in the LFoundry 150 nm CMOS process. The described device, named LF-Monopix, was designed as a proof of concept of a fully monolithic sensor capable of operating in the environment of outer layers of the ATLAS Inner Tracker upgrade for the High Luminosity Large Hadron Collider (HL-LHC). Implementing such a device in the detector module will result in a lower production cost and lower material budget compared to the presently used hybrid designs. In this paper the chip architecture will be described followed by the simulation and measurement results.
△ Less
Submitted 15 November, 2017; v1 submitted 3 November, 2017;
originally announced November 2017.
-
Depleted fully monolithic CMOS pixel detectors using a column based readout architecture for the ATLAS Inner Tracker upgrade
Authors:
T. Wang,
M. Barbero,
I. Berdalovic,
C. Bespin,
S. Bhat,
P. Breugnon,
I. Caicedo,
R. Cardella,
Z. Chen,
Y. Degerli,
N. Egidos,
S. Godiot,
F. Guilloux,
T. Hemperek,
T. Hirono,
H. Krüger,
T. Kugathasan,
F. Hügging,
C. A. Marin Tobon,
K. Moustakas,
P. Pangaud,
P. Schwemling,
H. Pernegger,
D-L. Pohl,
A. Rozanov
, et al. (3 additional authors not shown)
Abstract:
Depleted monolithic active pixel sensors (DMAPS), which exploit high voltage and/or high resistivity add-ons of modern CMOS technologies to achieve substantial depletion in the sensing volume, have proven to have high radiation tolerance towards the requirements of ATLAS in the high-luminosity LHC era. Depleted fully monolithic CMOS pixels with fast readout architectures are currently being develo…
▽ More
Depleted monolithic active pixel sensors (DMAPS), which exploit high voltage and/or high resistivity add-ons of modern CMOS technologies to achieve substantial depletion in the sensing volume, have proven to have high radiation tolerance towards the requirements of ATLAS in the high-luminosity LHC era. Depleted fully monolithic CMOS pixels with fast readout architectures are currently being developed as promising candidates for the outer pixel layers of the future ATLAS Inner Tracker, which will be installed during the phase II upgrade of ATLAS around year 2025. In this work, two DMAPS prototype designs, named LF-MonoPix and TJ-MonoPix, are presented. LF-MonoPix was designed and fabricated in the LFoundry 150~nm CMOS technology, and TJ-MonoPix has been designed in the TowerJazz 180~nm CMOS technology. Both chips employ the same readout architecture, i.e. the column drain architecture, whereas different sensor implementation concepts are pursued. The design of the two prototypes will be described. First measurement results for LF-MonoPix will also be shown.
△ Less
Submitted 29 September, 2017;
originally announced October 2017.
-
Development of a Depleted Monolithic CMOS Sensor in a 150 nm CMOS Technology for the ATLAS Inner Tracker Upgrade
Authors:
T. Wang,
P. Rymaszewski,
M. Barbero,
Y. Degerli,
S. Godiot,
F. Guilloux,
T. Hemperek,
T. Hirono,
H. Krüger,
J. Liu,
F. Orsini,
P. Pangaud,
A. Rozanov,
N. Wermes
Abstract:
The recent R&D focus on CMOS sensors with charge collection in a depleted zone has opened new perspectives for CMOS sensors as fast and radiation hard pixel devices. These sensors, labelled as depleted CMOS sensors (DMAPS), have already shown promising performance as feasible candidates for the ATLAS Inner Tracker (ITk) upgrade, possibly replacing the current passive sensors. A further step to exp…
▽ More
The recent R&D focus on CMOS sensors with charge collection in a depleted zone has opened new perspectives for CMOS sensors as fast and radiation hard pixel devices. These sensors, labelled as depleted CMOS sensors (DMAPS), have already shown promising performance as feasible candidates for the ATLAS Inner Tracker (ITk) upgrade, possibly replacing the current passive sensors. A further step to exploit the potential of DMAPS is to investigate the suitability of equipping the outer layers of the ATLAS ITk upgrade with fully monolithic CMOS sensors. This paper presents the development of a depleted monolithic CMOS pixel sensor designed in the LFoundry 150 nm CMOS technology, with the focus on design details and simulation results.
△ Less
Submitted 3 November, 2016;
originally announced November 2016.
-
A novel application of Fiber Bragg Grating (FBG) sensors in MPGD
Authors:
D. Abbaneo,
M. Abbas,
M. Abbrescia,
A. A. Abdelalim,
M. Abi Akl,
O. Aboamer,
D. Acosta,
A. Ahmad,
W. Ahmed,
W. Ahmed,
A. Aleksandrov,
R. Aly,
P. Altieri,
C. Asawatangtrakuldee,
P. Aspell,
Y. Assran,
I. Awan,
S. Bally,
Y. Ban,
S. Banerjee,
V. Barashko,
P. Barria,
G. Bencze,
N. Beni,
L. Benussi
, et al. (133 additional authors not shown)
Abstract:
We present a novel application of Fiber Bragg Grating (FBG) sensors in the construction and characterisation of Micro Pattern Gaseous Detector (MPGD), with particular attention to the realisation of the largest triple (Gas electron Multiplier) GEM chambers so far operated, the GE1/1 chambers of the CMS experiment at LHC. The GE1/1 CMS project consists of 144 GEM chambers of about 0.5 m2 active are…
▽ More
We present a novel application of Fiber Bragg Grating (FBG) sensors in the construction and characterisation of Micro Pattern Gaseous Detector (MPGD), with particular attention to the realisation of the largest triple (Gas electron Multiplier) GEM chambers so far operated, the GE1/1 chambers of the CMS experiment at LHC. The GE1/1 CMS project consists of 144 GEM chambers of about 0.5 m2 active area each, employing three GEM foils per chamber, to be installed in the forward region of the CMS endcap during the long shutdown of LHC in 2108-2019. The large active area of each GE1/1 chamber consists of GEM foils that are mechanically stretched in order to secure their flatness and the consequent uniform performance of the GE1/1 chamber across its whole active surface. So far FBGs have been used in high energy physics mainly as high precision positioning and re-positioning sensors and as low cost, easy to mount, low space consuming temperature sensors. FBGs are also commonly used for very precise strain measurements in material studies. In this work we present a novel use of FBGs as flatness and mechanical tensioning sensors applied to the wide GEM foils of the GE1/1 chambers. A network of FBG sensors have been used to determine the optimal mechanical tension applied and to characterise the mechanical tension that should be applied to the foils. We discuss the results of the test done on a full-sized GE1/1 final prototype, the studies done to fully characterise the GEM material, how this information was used to define a standard assembly procedure and possible future developments.
△ Less
Submitted 28 December, 2015;
originally announced December 2015.
-
Fiber Bragg Grating (FBG) sensors as flatness and mechanical stretching sensors
Authors:
D. Abbaneo,
M. Abbas,
M. Abbrescia,
A. A. Abdelalim,
M. Abi Akl,
O. Aboamer,
D. Acosta,
A. Ahmad,
W. Ahmed,
W. Ahmed,
A. Aleksandrov,
R. Aly,
P. Altieri,
C. Asawatangtrakuldee,
P. Aspell,
Y. Assran,
I. Awan,
S. Bally,
Y. Ban,
S. Banerjee,
V. Barashko,
P. Barria,
G. Bencze,
N. Beni,
L. Benussi
, et al. (133 additional authors not shown)
Abstract:
A novel approach which uses Fibre Bragg Grating (FBG) sensors has been utilised to assess and monitor the flatness of Gaseous Electron Multipliers (GEM) foils. The setup layout and preliminary results are presented.
A novel approach which uses Fibre Bragg Grating (FBG) sensors has been utilised to assess and monitor the flatness of Gaseous Electron Multipliers (GEM) foils. The setup layout and preliminary results are presented.
△ Less
Submitted 28 December, 2015;
originally announced December 2015.
-
Analogue Sum ASIC for L1 Trigger Decision in Cherenkov Telescope Cameras
Authors:
Joan Abel Barrio,
Oscar Blanch,
Joan Boix,
Eric Delagnes,
Carlos Delgado,
Lluis Freixas Coromina,
David Gascon,
Fabrice Guilloux,
Ruben Lopez Coto,
Gustavo Martinez,
Andreu Sanuy,
Luis Angel Tejedor
Abstract:
The Cherenkov Telescope Array (CTA) project aims to build the largest ground-based gamma-ray observatory based on an array of Imaging Atmospheric Cherenkov Telescopes (IACTs). The CTA will implement a multi-level trigger system to distinguish between gamma ray-like induced showers and background images induced by night sky background (NSB) light. The trigger system is based on coincident detection…
▽ More
The Cherenkov Telescope Array (CTA) project aims to build the largest ground-based gamma-ray observatory based on an array of Imaging Atmospheric Cherenkov Telescopes (IACTs). The CTA will implement a multi-level trigger system to distinguish between gamma ray-like induced showers and background images induced by night sky background (NSB) light. The trigger system is based on coincident detections among pixels (level 0 trigger), clusters of pixels (level 1) or telescopes. In this article, the first version of the application specific integrated circuit (ASIC) for Level 1 trigger system is presented, capable of working with different Level 0 strategies and different trigger region sizes. In addition, it complies with all the requirements specified by the CTA project, specially the most critical ones as regards noise, bandwidth, dynamic range and power consumption. All these features make the presented system very suitable for use in the CTA cameras and improve the features of discrete components prototypes of the L1 trigger circuit in terms of compactness, noise, performance and power consumption.
△ Less
Submitted 30 October, 2014;
originally announced October 2014.
-
M.i.p. detection performances of a 100 us read-out CMOS pixel sensor with digitised outputs
Authors:
Marc Winter,
Jerome Baudot,
Auguste Besson,
Claude Colledani,
Yavuz Degerli,
Rita De Masi,
Andrei Dorokhov,
Guy Doziere,
Wojciech Dulinski,
Marie Gelin,
Fabrice Guilloux,
Abdelkader Himmi,
Christine Hu-Guo,
Frederic Morel,
Fabienne Orsini,
Isabelle Valin,
Georgios Voutsinas
Abstract:
Swift, high resolution CMOS pixel sensors are being developed for the ILC vertex detector, aiming to allow approaching the interaction point very closely. A major issue is the time resolution of the sensors needed to deal with the high occupancy generated by the beam related background. A 128x576 pixel sensor providing digitised outputs at a read-out time of 92.5 us, was fabricated in 2008 withi…
▽ More
Swift, high resolution CMOS pixel sensors are being developed for the ILC vertex detector, aiming to allow approaching the interaction point very closely. A major issue is the time resolution of the sensors needed to deal with the high occupancy generated by the beam related background. A 128x576 pixel sensor providing digitised outputs at a read-out time of 92.5 us, was fabricated in 2008 within the EU project EUDET, and tested with charged particles at the CERN-SPS. Its prominent performances in terms of noise, detection efficiency versus fake hit rate, spatial resolution and radiation tolerance are overviewed. They validate the sensor architecture.
△ Less
Submitted 16 February, 2009;
originally announced February 2009.
