-
Thermal performance estimation for cryogenic storage tanks: Application to liquid hydrogen
Authors:
Ailo Aasen,
Sindre Stenen Blakseth,
André Massing,
Petter Nekså,
Magnus Aa. Gjennestad
Abstract:
The design of cryogenic liquid storage solutions requires accurate methods for estimating heat ingress, from the material level to the tank level. For insulation materials, thermal performance is usually measured using ambient conditions and liquid nitrogen at 77 K as boundary temperatures. A key question is how much heat ingress increases when storing liquid hydrogen LH$_2$ at 20 K. We derive the…
▽ More
The design of cryogenic liquid storage solutions requires accurate methods for estimating heat ingress, from the material level to the tank level. For insulation materials, thermal performance is usually measured using ambient conditions and liquid nitrogen at 77 K as boundary temperatures. A key question is how much heat ingress increases when storing liquid hydrogen LH$_2$ at 20 K. We derive theoretical bounds on the increased heat ingress, and show that it remains below 26%. Additionally, we demonstrate that heat ingress is much more sensitive to the warm boundary temperature than the cold boundary temperature. At the tank level, we compare two methods for assessing the steady-state thermal performance of cryogenic tanks: thermal network models and the heat equation solved with the finite element method. The latter offers high accuracy and adaptability for complex geometries, while thermal network models benefit from simplicity, speed and robustness. We apply both approaches to a self-supported LH$_2$ tank concept for maritime transport and analyze sensitivity to structural support thickness, warm boundary temperature, and choice of insulation material. The thermal network model can estimate heat ingress with $\sim$1% error and the cold-spot temperature with error less than 1 K.
△ Less
Submitted 30 January, 2025;
originally announced January 2025.
-
A combined fluid-dynamic and thermodynamic model to predict the onset of rapid phase transitions in LNG spills
Authors:
Karl Yngve Lervåg,
Hans L. Skarsvåg,
Eskil Aursand,
Jabir Ali Ouassou,
Morten Hammer,
Gunhild Reigstad,
Åsmund Ervik,
Eirik Holm Fyhn,
Magnus Aa. Gjennestad,
Peder Aursand,
Øivind Wilhelmsen
Abstract:
Transport of liquefied natural gas (LNG) by ship occurs globally on a massive scale. The large temperature difference between LNG and water means LNG will boil violently if spilled onto water. This may cause a physical explosion known as rapid phase transition (RPT). Since RPT results from a complex interplay between physical phenomena on several scales, the risk of its occurrence is difficult to…
▽ More
Transport of liquefied natural gas (LNG) by ship occurs globally on a massive scale. The large temperature difference between LNG and water means LNG will boil violently if spilled onto water. This may cause a physical explosion known as rapid phase transition (RPT). Since RPT results from a complex interplay between physical phenomena on several scales, the risk of its occurrence is difficult to estimate. In this work, we present a combined fluid-dynamic and thermodynamic model to predict the onset of delayed RPT. On the basis of the full coupled model, we derive analytical solutions for the location and time of delayed RPT in an axisymmetric steady-state spill of LNG onto water. These equations are shown to be accurate when compared to simulation results for a range of relevant parameters. The relative discrepancy between the analytic solutions and predictions from the full coupled model is within 2% for the RPT position and within 8% for the time of RPT. This provides a simple procedure to quantify the risk of occurrence for delayed RPT for LNG on water. Due to its modular formulation, the full coupled model can straightforwardly be extended to study RPT in other systems.
△ Less
Submitted 19 November, 2020; v1 submitted 19 February, 2020;
originally announced February 2020.
-
Onsager-Symmetry Obeyed in Athermal Mesoscopic Systems: Two-Phase Flow in Porous Media
Authors:
Mathias Winkler,
Magnus Aa. Gjennestad,
Dick Bedeaux,
Signe Kjelstrup,
Raffaela Cabriolu,
Alex Hansen
Abstract:
We compute the fluid flow time-correlation functions of incompressible, immiscible two-phase flow in porous media using a 2D network model. Given a properly chosen representative elementary volume, the flow rate distributions are Gaussian and the integrals of time correlation functions of the flows are found to converge to a finite value. The integrated cross-correlations become symmetric, obeying…
▽ More
We compute the fluid flow time-correlation functions of incompressible, immiscible two-phase flow in porous media using a 2D network model. Given a properly chosen representative elementary volume, the flow rate distributions are Gaussian and the integrals of time correlation functions of the flows are found to converge to a finite value. The integrated cross-correlations become symmetric, obeying Onsager's reciprocal relations. These findings support the proposal of a non-equilibrium thermodynamic description for two-phase flow in porous media.
△ Less
Submitted 13 January, 2020;
originally announced January 2020.
-
Pore network modeling of the effects of viscosity ratio and pressure gradient on steady-state incompressible two-phase flow in porous media
Authors:
Magnus Aa. Gjennestad,
Mathias Winkler,
Alex Hansen
Abstract:
We perform more than 6000 steady-state simulations with a dynamic pore network model, corresponding to a large span in viscosity ratios and capillary numbers. From these simulations, dimensionless quantities such as relative permeabilities, residual saturations, mobility ratios and fractional flows are computed. Relative permeabilities and residual saturations show many of the same qualitative fea…
▽ More
We perform more than 6000 steady-state simulations with a dynamic pore network model, corresponding to a large span in viscosity ratios and capillary numbers. From these simulations, dimensionless quantities such as relative permeabilities, residual saturations, mobility ratios and fractional flows are computed. Relative permeabilities and residual saturations show many of the same qualitative features observed in other experimental and modeling studies. However, while other studies find that relative permeabilities converge to straight lines at high capillary numbers we find that this is not the case when viscosity ratios are different from 1. Our conclusion is that departure from straight lines occurs when fluids mix rather than form decoupled flow channels. Another consequence of the mixing is that computed fractional flow curves, plotted against saturation, lie closer to the diagonal than they would otherwise do. At lower capillary numbers, fractional flow curves have a classical S-shape. Ratios of average mobility to their high-capillary number limit values are also considered. These vary, roughly, between 0 and 1, although values larger than 1 are also observed. For a given saturation and viscosity ratio, the mobilities are not always monotonically increasing with the pressure gradient. While increasing the pressure gradient mobilizes more fluid and activates more flow paths, when the mobilized fluid is more viscous, a reduction in average mobility may occur.
△ Less
Submitted 18 November, 2019;
originally announced November 2019.
-
Thermodynamic stability of droplets, bubbles and thick films in open and closed pores
Authors:
Magnus Aa. Gjennestad,
Øivind Wilhelmsen
Abstract:
A fluid in a pore can form diverse heterogeneous structures. We combine a capillary description with the cubic-plus-association equation of state to study the thermodynamic stability of droplets, bubbles and films of water at 358 K in a cylindrically symmetric pore. The equilibrium structure depends strongly on the size of the pore and whether the pore is closed or connected to a particle reservoi…
▽ More
A fluid in a pore can form diverse heterogeneous structures. We combine a capillary description with the cubic-plus-association equation of state to study the thermodynamic stability of droplets, bubbles and films of water at 358 K in a cylindrically symmetric pore. The equilibrium structure depends strongly on the size of the pore and whether the pore is closed or connected to a particle reservoir. A new methodology is presented to analyze the thermodynamic stability of films, where the integral that describes the total energy of the system is approximated by a quadrature rule. We show that, for large pores, the thermodynamic stability limit of adsorbed droplets and bubbles in both open and closed pores is governed by their mechanical stability, which is closely linked to the pore shape. This is also the case for a film in a closed pore. In open pores, the film is chemically unstable except for very low film-phase contact angles and for a limited range in external pressure. This result emphasizes the need to invoke a complete thermodynamic stability analysis, and not restrict the discussion to mechanical stability. A common feature for most of the heterogeneous structures examined is the appearance of regions where the structure is metastable with respect to a pore filled with a homogeneous fluid. In the closed pores, these regions grow considerably in size when the pores become smaller. [...] Complete phase diagrams are presented that compare all the investigated structures. In open pores at equilibrium, the most stable structure is either the homogeneous phase or adsorbed droplets and bubbles, depending on the type of phase in the external reservoir. Smaller pores allow for droplets and bubbles to adsorb for a larger span in pressure. In closed pores, most of the investigated configurations can occur depending on the total density, the contact angle and the pore shape. [...]
△ Less
Submitted 3 September, 2019;
originally announced September 2019.
-
A Dynamic Network Simulator for Immiscible Two-Phase Flow in Porous Media
Authors:
Santanu Sinha,
Magnus Aa. Gjennestad,
Morten Vassvik,
Alex Hansen
Abstract:
We present in detail a set of algorithms to carry out fluid displacements in a dynamic pore-network model of immiscible two-phase flow in porous media. The algorithms are general and applicable to regular and irregular pore networks in two and three dimensions with different boundary conditions. Implementing these sets of algorithms, we describe a dynamic pore-network model and reproduce some of t…
▽ More
We present in detail a set of algorithms to carry out fluid displacements in a dynamic pore-network model of immiscible two-phase flow in porous media. The algorithms are general and applicable to regular and irregular pore networks in two and three dimensions with different boundary conditions. Implementing these sets of algorithms, we describe a dynamic pore-network model and reproduce some of the fundamental properties of both the transient and steady-state two-phase flow. During drainage displacements, we show that the model can reproduce the flow patterns corresponding to viscous fingering, capillary fingering and stable displacement by altering the capillary number and the viscosity ratio. In steady-state flow, the model verifies the linear to non-linear transition of the effective rheological properties and satisfy the relations between the seepage velocities of two-phase flow in porous media.
△ Less
Submitted 30 July, 2019;
originally announced July 2019.
-
Performance analysis of heat and energy recovery ventilators using exergy analysis and nonequilibrium thermodynamics
Authors:
Magnus Aa. Gjennestad,
Eskil Aursand,
Elisa Magnanelli,
Jon Pharoah
Abstract:
The increased attention to energy savings has contributed to more widespread use of energy recovery systems for building ventilation. We investigate the efficiency of such systems under different outdoor conditions using exergy analysis and nonequilibrium thermodynamics. This analysis makes it possible to assess performance in terms of loss of work potential, to account for the different quality o…
▽ More
The increased attention to energy savings has contributed to more widespread use of energy recovery systems for building ventilation. We investigate the efficiency of such systems under different outdoor conditions using exergy analysis and nonequilibrium thermodynamics. This analysis makes it possible to assess performance in terms of loss of work potential, to account for the different quality of energy and to localize and compare the different sources of loss in the system. It also enables the use of exergy efficiency as a single performance parameter, in contrast to the several indicators that are commonly used. These more common indicators are difficult to compare and relate to each other. Further, since there is no obvious optimal trade-off between them, it is challenging to combine them and develop a global performance indicator that allows for a sensible comparison of different technical solutions and different types of recovery devices. We illustrate the concepts by applying the analysis to a heat recovery ventilator (HRV) and to a structurally similar membrane energy recovery ventilator (MERV) that can exchange both heat and moisture. We show how the exergy efficiency can be used to identify the range of operating conditions for which the recovery ventilator is not beneficial as the energy cost is greater than the energy recovery. This is not trivial using traditional performance parameters, yet it is a natural outcome of exergy analysis. In addition, we identify the mechanism by which work potential is lost, which can help the eventual optimization of both the recovery process and the auxiliary systems present in ventilation systems.
△ Less
Submitted 2 July, 2018; v1 submitted 22 May, 2018;
originally announced June 2018.
-
Stable and efficient time integration of a dynamic pore network model for two-phase flow in porous media
Authors:
Magnus Aa. Gjennestad,
Morten Vassvik,
Signe Kjelstrup,
Alex Hansen
Abstract:
We study three different time integration methods for a dynamic pore network model for immiscible two-phase flow in porous media. Considered are two explicit methods, the forward Euler and midpoint methods, and a new semi-implicit method developed herein. The explicit methods are known to suffer from numerical instabilities at low capillary numbers. A new time-step criterion is suggested in order…
▽ More
We study three different time integration methods for a dynamic pore network model for immiscible two-phase flow in porous media. Considered are two explicit methods, the forward Euler and midpoint methods, and a new semi-implicit method developed herein. The explicit methods are known to suffer from numerical instabilities at low capillary numbers. A new time-step criterion is suggested in order to stabilize them. Numerical experiments, including a Haines jump case, are performed and these demonstrate that stabilization is achieved. Further, the results from the Haines jump case are consistent with experimental observations. A performance analysis reveals that the semi-implicit method is able to perform stable simulations with much less computational effort than the explicit methods at low capillary numbers. The relative benefit of using the semi-implicit method increases with decreasing capillary number $\mathrm{Ca}$, and at $\mathrm{Ca} \sim 10^{-8}$ the computational time needed is reduced by three orders of magnitude. This increased efficiency enables simulations in the low-capillary number regime that are unfeasible with explicit methods and the range of capillary numbers for which the pore network model is a tractable modeling alternative is thus greatly extended by the semi-implicit method.
△ Less
Submitted 2 July, 2018; v1 submitted 2 February, 2018;
originally announced February 2018.
-
Rheology of High-Capillary Number Flow in Porous Media
Authors:
Santanu Sinha,
Magnus Aa. Gjennestad,
Morten Vassvik,
Mathias Winkler,
Alex Hansen,
Eirik G. Flekkøy
Abstract:
Immiscible fluids flowing at high capillary numbers in porous media may be characterized by an effective viscosity. We demonstrate that the effective viscosity is well described by the Lichtenecker-Rother equation. The exponent $α$ in this equation takes either the value 1 or 0.6 in two- and 0.5 in three-dimensional systems depending on the pore geometry. Our arguments are based on analytical and…
▽ More
Immiscible fluids flowing at high capillary numbers in porous media may be characterized by an effective viscosity. We demonstrate that the effective viscosity is well described by the Lichtenecker-Rother equation. The exponent $α$ in this equation takes either the value 1 or 0.6 in two- and 0.5 in three-dimensional systems depending on the pore geometry. Our arguments are based on analytical and numerical methods.
△ Less
Submitted 19 December, 2017;
originally announced December 2017.
-
Relations between Seepage Velocities in Immiscible, Incompressible Two-Phase Flow in Porous Media
Authors:
Alex Hansen,
Santanu Sinha,
Dick Bedeaux,
Signe Kjelstrup,
Magnus Aa. Gjennestad,
Morten Vassvik
Abstract:
Based on thermodynamic considerations we derive a set of equations relating the seepage velocities of the fluid components in immiscible and incompressible two-phase flow in porous media. They necessitate the introduction of a new velocity function, the co-moving velocity. This velocity function is a characteristic of the porous medium. Together with a constitutive relation between the velocities…
▽ More
Based on thermodynamic considerations we derive a set of equations relating the seepage velocities of the fluid components in immiscible and incompressible two-phase flow in porous media. They necessitate the introduction of a new velocity function, the co-moving velocity. This velocity function is a characteristic of the porous medium. Together with a constitutive relation between the velocities and the driving forces, such as the pressure gradient, these equations form a closed set. We solve four versions of the capillary tube model analytically using this theory. We test the theory numerically on a network model.
△ Less
Submitted 19 December, 2017;
originally announced December 2017.
-
Computation of three-dimensional three-phase flow of carbon dioxide using a high-order WENO scheme
Authors:
Magnus Aa. Gjennestad,
Andrea Gruber,
Karl Yngve Lervåg,
Øyvind Johansen,
Åsmund Ervik,
Morten Hammer,
Svend Tollak Munkejord
Abstract:
We have developed a high-order numerical method for the 3D simulation of viscous and inviscid multiphase flow described by a homogeneous equilibrium model and a general equation of state. Here we focus on single-phase, two-phase (gas-liquid or gas-solid) and three-phase (gas-liquid-solid) flow of CO2 whose thermodynamic properties are calculated using the Span-Wagner reference equation of state. T…
▽ More
We have developed a high-order numerical method for the 3D simulation of viscous and inviscid multiphase flow described by a homogeneous equilibrium model and a general equation of state. Here we focus on single-phase, two-phase (gas-liquid or gas-solid) and three-phase (gas-liquid-solid) flow of CO2 whose thermodynamic properties are calculated using the Span-Wagner reference equation of state. The governing equations are spatially discretized on a uniform Cartesian grid using the finite-volume method with a fifth-order weighted essentially non-oscillatory (WENO) scheme and the robust first-order centered (FORCE) flux. The solution is integrated in time using a third-order strong-stability-preserving Runge-Kutta method. We demonstrate close to fifth-order convergence for advection-diffusion and for smooth single- and two-phase flows. Quantitative agreement with experimental data is obtained for a direct numerical simulation of an air jet flowing from a rectangular nozzle. Quantitative agreement is also obtained for the shape and dimensions of the barrel shock in two highly underexpanded CO2 jets.
△ Less
Submitted 31 July, 2017;
originally announced July 2017.
-
A multi-phase ferrofluid flow model with equation of state for thermomagnetic pumping and heat transfer
Authors:
Eskil Aursand,
Magnus Aa. Gjennestad,
Karl Yngve Lervåg,
Halvor Lund
Abstract:
A one-dimensional multi-phase flow model for thermomagnetically pumped ferrofluid with heat transfer is proposed. The thermodynamic model is a combination of a simplified particle model and thermodynamic equations of state for the base fluid. The magnetization model is based on statistical mechanics, taking into account non-uniform particle size distributions. An implementation of the proposed mod…
▽ More
A one-dimensional multi-phase flow model for thermomagnetically pumped ferrofluid with heat transfer is proposed. The thermodynamic model is a combination of a simplified particle model and thermodynamic equations of state for the base fluid. The magnetization model is based on statistical mechanics, taking into account non-uniform particle size distributions. An implementation of the proposed model is validated against experiments from the literature, and found to give good predictions for the thermomagnetic pumping performance. However, the results reveal a very large sensitivity to uncertainties in heat transfer coefficient predictions.
△ Less
Submitted 31 May, 2016;
originally announced May 2016.
-
Potential of enhancing a natural convection loop with a thermomagnetically pumped ferrofluid
Authors:
Eskil Aursand,
Magnus Aa. Gjennestad,
Karl Yngve Lervåg,
Halvor Lund
Abstract:
The feasibility of using a thermomagnetically pumped ferrofluid to enhance the performance of a natural convection cooling loop is investigated. First, a simplified analytical estimate for the thermomagnetic pumping action is derived, and then design rules for optimal solenoid and ferrofluid are presented. The design rules are used to set up a medium-scale (1 m, 10-1000 W) case study, which is mod…
▽ More
The feasibility of using a thermomagnetically pumped ferrofluid to enhance the performance of a natural convection cooling loop is investigated. First, a simplified analytical estimate for the thermomagnetic pumping action is derived, and then design rules for optimal solenoid and ferrofluid are presented. The design rules are used to set up a medium-scale (1 m, 10-1000 W) case study, which is modeled using a previously published and validated model (Aursand et al. [1]). The results show that the thermomagnetic driving force is significant compared to the natural convection driving force, and may in some cases greatly surpass it. The results also indicate that cooling performance can be increased by factors up to 4 and 2 in the single-phase and two- phase regimes, respectively, even when taking into the account the added heat from the solenoid. The performance increases can alternatively be used to obtain a reduction in heat-sink size by up to 75 %.
△ Less
Submitted 31 May, 2016;
originally announced May 2016.
