-
Influence of Environmentally Affected Hole Transport Layers on Spatial Homogeneity and Charge Transport Dynamics of Organic Solar Cells
Authors:
Huei -Ting Chien,
Florian Pilat,
Thomas Griesser,
Harald Fitzek,
Peter Poelt,
Bettina Friedel
Abstract:
After the efficiency of organic photovoltaic (OPV) cells achieved more than 10%, the control of stability and degradation mechanisms of solar cells became a prominent task. The improvement of device efficiency due to incorporation of a hole-transport layer (HTL) in bulk-heterojunction solar cells has been extensively reported. However, the most widely used HTL material, PEDOT:PSS is frequently sus…
▽ More
After the efficiency of organic photovoltaic (OPV) cells achieved more than 10%, the control of stability and degradation mechanisms of solar cells became a prominent task. The improvement of device efficiency due to incorporation of a hole-transport layer (HTL) in bulk-heterojunction solar cells has been extensively reported. However, the most widely used HTL material, PEDOT:PSS is frequently suspected to be the dominating source for devices instability under environmental conditions. Thereby effects like photooxidation and electrode corrosion are often reported to shorten device lifetime. However, often in environmental device studies, the source of degradation, whether being from the HTL, the active layer or the metal cathode are rather difficult to distinguish, because the external diffusion of oxygen and water affects all components. In this study, different HTLs, namely prepared from traditional PEDOT:PSS and also two types of molybdenum trioxide (MoO3), are exposed to different environments such as oxygen, light or humidity, prior to device finalization under inert conditions. This allows investigating any effects within the HTL and from reactions at its interface to the indium-tin-oxide electrode or the active layer. The surface and bulk chemistry of the exposed HTL has been monitored and discussed in context to the observed device physics, dynamic charge transport and spatial performance homogeneity of the according OPV device. The results show that merely humidity-exposure of the HTL leads to decreased device performance for PEDOT:PSS, but also for one type of the tested MoO3. The losses are related to the amount of absorbed water in the HTL, inducing loss of active area in terms of interfacial contact. The device with PEDOT:PSS HTL after humid air exposure showed seriously decreased photocurrent by micro-delamination of swelling/shrinkage of the hygroscopic layer.
△ Less
Submitted 24 June, 2019;
originally announced August 2019.
-
Effects of Hole-Transport Layer Homogeneity in Organic Solar Cells, A Multi-Length Scale Study
Authors:
Huei-Ting Chien,
Markus Poelzl,
Georg Koller,
Susanna Challinger,
Callum Fairbairn,
Iain Baikie,
Markus Kratzer,
Christian Teichert,
Bettina Friedel
Abstract:
Irreproducibility is a serious issue in thin film organic photovoltaic (OPV) devices, as smallest local inhomogeneities can change the entire behaviour of identically built devices without showing obvious failure. Inhomogeneities can occur at various steps of device preparation and appear in all layers with different length scales and impact. The hole-transport interlayer (HTL) in OPV devices bloc…
▽ More
Irreproducibility is a serious issue in thin film organic photovoltaic (OPV) devices, as smallest local inhomogeneities can change the entire behaviour of identically built devices without showing obvious failure. Inhomogeneities can occur at various steps of device preparation and appear in all layers with different length scales and impact. The hole-transport interlayer (HTL) in OPV devices blocks unwanted electron diffusion to the anode and corrects energetic mismatch between oxide electrode and organic semiconductor. Most commonly used is commercial ink based on poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT PSS) colloidal particles. However, exactly these are suspected to cause microscopic inhomogeneities, causing known irreproducibility of device characteristics. Considering PEDOT:PSS acidity-caused electrode corrosion, it is questionable how much impact colloids have on device homogeneity. In this report, we give proof that a colloidal HTL does not necessarily cause device inhomogeneity and decreased efficiency, by comparing OPV devices with different HTLs, namely from commercial PEDOT:PSS ink and from MoO3, obtained from two liquid precursors, leading to quasi-continuous or colloidal layers. With a combination of X-ray diffraction, atomic force and Kelvin probe microscopy, photoelectron and ambient air photoemission spectroscopy, we discuss the layers properties from nano- to macroscale and demonstrate their impact upon implementation into OPV devices, via spatially-resolved characterization.
△ Less
Submitted 24 June, 2019;
originally announced August 2019.
-
Characterization of Surface and Structure of in-situ Doped Sol-Gel-Derived Silicon Carbide
Authors:
Olivia Kettner,
Sanja Simic,
Birgit Kunert,
Robert Schennach,
Roland Resel,
Thomas Griesser,
Bettina Friedel
Abstract:
Silicon carbide (SiC), is an artificial semiconductor used for high-power transistors and blue LEDs, for its extraordinary properties. SiC would be attractive for more applications, but large-scale or large-surface area fabrication, with control over defects and surface is challenging. Sol-gel based techniques are an affordable alternative towards such requirements. This report describes two types…
▽ More
Silicon carbide (SiC), is an artificial semiconductor used for high-power transistors and blue LEDs, for its extraordinary properties. SiC would be attractive for more applications, but large-scale or large-surface area fabrication, with control over defects and surface is challenging. Sol-gel based techniques are an affordable alternative towards such requirements. This report describes two types of microcrystalline SiC derived after carbothermal reduction from sol-gel-based precursors, one with nitrogen added, the other aluminum. Characterization of their bulk, structure and surface shows that incorporation of dopants affects the formation of polytypes and surface chemistry. Nitrogen leads exclusively to cubic SiC, exhibiting a native oxide surface. Presence of aluminum instead promotes growth of hexagonal polytypes and induces self-passivation of the crystallites surface during growth. This is established by hydrogenation of silicon bonds and formation of a protecting aluminum carbonate species. XPS provides support for the suggested mechanism. This passivation is achieved in only one step, solely by aluminium in the precursor. Hence, it is shown that growth, doping and passivation of SiC can be performed as one-pot synthesis. Material without insulating oxide and a limited number of defects is highly valuable for applications involving surface-sensitive charge-transfer reactions, therefore the potential of this method is significant.
△ Less
Submitted 24 June, 2019;
originally announced June 2019.
-
Regenerated Cellulose Fiber Solar Cell
Authors:
Michael Ebner,
Robert Schennach,
Huei-Ting Chien,
Claudia Mayrhofer,
Armin Zankel,
Bettina Friedel
Abstract:
Wearable electronics and smart textiles are growing fields in the cause to integrate modern communication and computing tools into clothing instead of carrying around smart phones and tablets. Naturally, this also requires power sources to be integrated in textiles. In this paper, a proof-of-concept is presented in form of a photovoltaic cell based on a commercially available viscose fiber. This h…
▽ More
Wearable electronics and smart textiles are growing fields in the cause to integrate modern communication and computing tools into clothing instead of carrying around smart phones and tablets. Naturally, this also requires power sources to be integrated in textiles. In this paper, a proof-of-concept is presented in form of a photovoltaic cell based on a commercially available viscose fiber. This has been realized using a silver nanowire network around the viscose fiber to establish electrical contact and a photoactive coating using the standard workhorse among organic thin film solar cells, a blend of poly(3-hexylthiophene) (P3HT) and phenyl-C61-butyric acid methyl ester (PCBM). Structure and performance of single fiber devices demonstrate their feasibility and functionality. The applied materials and methods are compatible to solution processing therewith qualifying for potential roll-to-roll large-scale production.
△ Less
Submitted 19 August, 2018;
originally announced August 2018.
-
Short-Term Environmental Effects and Their Influence on Spatial Homogeneity of Organic Solar Cell Functionality
Authors:
Huei-Ting Chien,
Peter W. Zach,
Bettina Friedel
Abstract:
Here, we focus on induced degradation and spatial inhomogeneity of organic photovoltaic devices under different environmental conditions, uncoupled from the influence of a hole-transport (HT) layer. During testing of devices comprising the standard photoactive layer of P3HT as donor, blended with PCBM as acceptor, a comparison was made between the nonencapsulated devices upon exposure to dry air,…
▽ More
Here, we focus on induced degradation and spatial inhomogeneity of organic photovoltaic devices under different environmental conditions, uncoupled from the influence of a hole-transport (HT) layer. During testing of devices comprising the standard photoactive layer of P3HT as donor, blended with PCBM as acceptor, a comparison was made between the nonencapsulated devices upon exposure to dry air, dry air with illumination and humid air. The impact on the active layer's photophysics is discussed, along with the device physics in terms of integral solar cell performance and spatially resolved photocurrent distribution with point-to-point analysis of the diode characteristics to determine the origin of the observed behavior. The results show that even without the widely used hygroscopic HT layer, PEDOT:PSS, humidity is still a major factor in the short-term environmental degradation of organic solar cells with this architecture, and not only oxygen or light, as is often reported. Different from previous reports where water-induced device degradation was spatially homogeneous and formation of Al2O3 islands was only seen for oxygen permeation through pinholes in aluminum, we observed insulating islands merely after humidity exposure in the present study. Further, we demonstrated with laser beam induced current mapping and point-to-point diode analysis that the water-induced performance losses are a result of the exposed device area comprising regions with entirely unaltered high output and intact diode behavior and those with severe degradation showing detrimentally lowered output and voltage-independent charge blocking, which is essentially insulating behavior. It is suggested that this is caused by transport of water through pinholes to the organic/metal interface, where they form insulating oxide or hydroxide islands, while the organic active layer stays unharmed.
△ Less
Submitted 19 August, 2018;
originally announced August 2018.
