-
Inclusion of sulfur chemistry in a validated C/H/O/N chemical network: identification of key C/S coupling pathways
Authors:
R. Veillet,
O. Venot,
B. Sirjean,
F. Citrangolo Destro,
R. Fournet,
A. Al-Refaie,
E. Hébrard,
P-A. Glaude,
R. Bounaceur
Abstract:
The detection of SO2 in both WASP-39 b and WASP-107 b recently brought more attention to the modeling of photochemistry in exoplanets. However, sulfur kinetics data is lacking in the literature for the full C/H/O/N/S system. The networks used to model this chemistry neglect the coupling between sulfur and other C/H/O/N species. We aimed to integrate sulfur kinetics to our previously developed C_0-…
▽ More
The detection of SO2 in both WASP-39 b and WASP-107 b recently brought more attention to the modeling of photochemistry in exoplanets. However, sulfur kinetics data is lacking in the literature for the full C/H/O/N/S system. The networks used to model this chemistry neglect the coupling between sulfur and other C/H/O/N species. We aimed to integrate sulfur kinetics to our previously developed C_0-C_2/H/O/N chemical network, with the inclusion of its coupling to carbon and nitrogen chemistry, for conditions between 500 - 2500 K and 100 - 10^-6 bar, and any atomic composition. To achieve this reliability, we used a dual approach, deriving the network from other available combustion networks and from original ab initio calculations where data was lacking. This was performed together with an extensive validation of the network on 1606 experimental measurements from the literature on the combustion and pyrolysis of multiple sulfur compounds such as H2S, CH3SH, CS2 and OCS. To examine the consequences of this new chemical network on exoplanets atmospheric studies, we generated abundance profiles for GJ 436 b, GJ 1214 b, HD 189733 b, HD 209458 b, WASP-39 b and WASP-107 b using the 1D kinetic model FRECKLL, calculated the corresponding transmission spectra using TauREx 3.1 and compared these results with other chemical networks used in exoplanet modeling with sulfur. The coupling between carbon and sulfur chemistry is found to be impactful on both abundance profiles and observables, with CH2S being its key species. CS2 abundance is found to be probably much higher than anticipated in current kinetic networks for exoplanets. The detection of CS2 in TOI-270 d highlights the importance of using validated chemical networks to improve the reliability of our models, particularly in the JWST era. Combustion and pyrolysis data are largely available tools that reveal to be very useful for this task.
△ Less
Submitted 17 May, 2025;
originally announced May 2025.
-
A Comparative Study of the Formation of Aromatics in Rich Methane Flames Doped by Unsaturated Compounds
Authors:
Hadj-Ali Gueniche,
Joffrey Biet,
Pierre-Alexandre Glaude,
René Fournet,
Frédérique Battin-Leclerc
Abstract:
For a better modeling of the importance of the different channels leading to the first aromatic ring, we have compared the structures of laminar rich premixed methane flames doped with several unsaturated hydrocarbons: allene and propyne, because they are precursors of propargyl radicals which are well known as having an important role in forming benzene, 1,3-butadiene to put in evidence a possi…
▽ More
For a better modeling of the importance of the different channels leading to the first aromatic ring, we have compared the structures of laminar rich premixed methane flames doped with several unsaturated hydrocarbons: allene and propyne, because they are precursors of propargyl radicals which are well known as having an important role in forming benzene, 1,3-butadiene to put in evidence a possible production of benzene due to reactions of C4 compounds, and, finally, cyclopentene which is a source of cyclopentadienylmethylene radicals which in turn are expected to easily isomerizes to give benzene. These flames have been stabilized on a burner at a pressure of 6.7 kPa (50 Torr) using argon as dilutant, for equivalence ratios (?) from 1.55 to 1.79. A unique mechanism, including the formation and decomposition of benzene and toluene, has been used to model the oxidation of allene, propyne, 1,3 butadiene and cyclopentene. The main reaction pathways of aromatics formation have been derived from reaction rate and sensitivity analyses and have been compared for the three types of additives. These combined analyses and comparisons can only been performed when a unique mechanism is available for all the studied additives.
△ Less
Submitted 26 May, 2009;
originally announced May 2009.
-
Hydrocarbons Heterogeneous Pyrolysis: Experiments and Modeling for Scramjet Thermal Management
Authors:
Marc Bouchez,
Emeric Daniau,
Nicolas Visez,
Olivier Herbinet,
René Fournet,
Paul-Marie Marquaire
Abstract:
The last years saw a renewal of interest for hypersonic research in general and regenerative cooling specifically, with a large increase of the number of dedicated facilities and technical studies. In order to quantify the heat transfer in the cooled structures and the composition of the cracked fuel entering the combustor, an accurate model of the thermal decomposition of the fuel is required.…
▽ More
The last years saw a renewal of interest for hypersonic research in general and regenerative cooling specifically, with a large increase of the number of dedicated facilities and technical studies. In order to quantify the heat transfer in the cooled structures and the composition of the cracked fuel entering the combustor, an accurate model of the thermal decomposition of the fuel is required. This model should be able to predict the fuel chemical composition and physical properties for a broad range of pressures, temperatures and cooling geometries. For this purpose, an experimental and modeling study of the thermal decomposition of generic molecules (long-chain or polycyclic alkanes) that could be good surrogates of real fuels, has been started at the DCPR laboratory located in Nancy (France). This successful effort leads to several versions of a complete kinetic model. These models do not assume any effect from the material that constitutes the cooling channel. A specific experimental study was performed with two different types of steel (regular: E37, stainless: 316L). Some results are given in the present paper.
△ Less
Submitted 28 April, 2009;
originally announced April 2009.
-
Etude cinétique de CVD de pyrocarbone obtenu par pyrolyse de propane
Authors:
Isabelle Ziegler-Devin,
René Fournet,
Paul-Marie Marquaire
Abstract:
High temeperature (900-1000\degree C) low pressure (<< 1 atm) pyrolysis of propane yields a pyrocarbon deposit, but also mainly hydrogen and hydrocarbons from methane to polyaromatics. 30 reaction products were exeperimentally quantified at different operating conditions. A detailed kinetic pyrolysis model (600 reactions) has been developed and validated based on the totality of experiments. Thi…
▽ More
High temeperature (900-1000\degree C) low pressure (<< 1 atm) pyrolysis of propane yields a pyrocarbon deposit, but also mainly hydrogen and hydrocarbons from methane to polyaromatics. 30 reaction products were exeperimentally quantified at different operating conditions. A detailed kinetic pyrolysis model (600 reactions) has been developed and validated based on the totality of experiments. This model includes a homogeneous model (describing the gas phase pyrolysis of propane) coupled with a heterogeneous model describing the pyrocarbon deposit.
△ Less
Submitted 27 April, 2009;
originally announced April 2009.
-
Theoretical Kinetic Study of the Ring Opening of Cyclic Alkanes
Authors:
Baptiste Sirjean,
Pierre-Alexandre Glaude,
M. F. Ruiz-Lopez,
René Fournet
Abstract:
This work reports a theoretical study of the gas phase unimolecular decomposition of cyclobutane, cyclopentane and cyclohexane by means of quantum chemical calculations. A biradical mechanism has been envisaged for each cycloalkane, and the main routes for the decomposition of the biradicals formed have been investigated at the CBS-QB3 level of theory. Thermochemical data (?H\degree f, S\degree,…
▽ More
This work reports a theoretical study of the gas phase unimolecular decomposition of cyclobutane, cyclopentane and cyclohexane by means of quantum chemical calculations. A biradical mechanism has been envisaged for each cycloalkane, and the main routes for the decomposition of the biradicals formed have been investigated at the CBS-QB3 level of theory. Thermochemical data (?H\degree f, S\degree, C\degree p) for all the involved species have been obtained by means of isodesmic reactions. Rate constants have been derived for all elementary reactions using transition state theory at 1 atm and temperatures ranging from 600 to 2000 K. These values have been compared with the few data available in the literature and showed a rather good agreement.
△ Less
Submitted 27 April, 2009;
originally announced April 2009.
-
Theoretical Study of the Thermal Decomposition of a Jet Fuel Surrogate
Authors:
Baptiste Sirjean,
Olivier Herbinet,
Pierre-Alexandre Glaude,
M. F. Ruiz-Lopez,
René Fournet
Abstract:
In a scramjet, the fuel can be used to cool down the engine walls. The thermal decomposition of the jet fuel changes the reacting mixture before its combustion. A numerical study of the pyrolysis of norbornane, a jet fuel surrogate, has been performed. Rate constants of some sensitive reaction channels have been calculated by means of quantum chemical calculations at the CBS-QB3 level of theory.…
▽ More
In a scramjet, the fuel can be used to cool down the engine walls. The thermal decomposition of the jet fuel changes the reacting mixture before its combustion. A numerical study of the pyrolysis of norbornane, a jet fuel surrogate, has been performed. Rate constants of some sensitive reaction channels have been calculated by means of quantum chemical calculations at the CBS-QB3 level of theory. The mechanism has been validated against experimental results obtained in a jet-stirred reactor and important and/or sensitive pathways have been derived.
△ Less
Submitted 22 April, 2009;
originally announced April 2009.
-
Theoretical kinetic study of the low temperature oxidation of ethanol
Authors:
René Fournet,
Pierre-Alexandre Glaude,
Roda Bounaceur,
Michel Molière
Abstract:
In order to improve the understanding of the low temperature combustion of ethanol, high-level ab initio calculations were performed for elementary reactions involving hydroxyethylperoxy radicals. These radicals come from the addition of hydroxethyl radicals (?CH3CHOH and ?CH2CH2OH) on oxygen molecule. Unimolecular reactions involving hydroxyethylperoxy radicals and their radical products were s…
▽ More
In order to improve the understanding of the low temperature combustion of ethanol, high-level ab initio calculations were performed for elementary reactions involving hydroxyethylperoxy radicals. These radicals come from the addition of hydroxethyl radicals (?CH3CHOH and ?CH2CH2OH) on oxygen molecule. Unimolecular reactions involving hydroxyethylperoxy radicals and their radical products were studied at the CBS-QB3 level of theory. The results allowed to highlight the principal ways of decomposition of these radicals. Calculations of potential energy surfaces showed that the principal channels lead to the formation of HO2 radicals which can be considered, at low temperature, as slightly reactive. However, in the case of CH3CH(OOH)O? radicals, a route of decomposition yields H atom and formic peracid, which is a branching agent that can strongly enhance the reactivity of ethanol in low temperature oxidation. In addition to these analyses, high-pressure limit rate constants were derived in the temperature range 400 to 1000 K.
△ Less
Submitted 20 April, 2009;
originally announced April 2009.
-
Detailed kinetic models for the low-temperature auto ignition of gasoline surrogates
Authors:
Roda Bounaceur,
Pierre-Alexandre Glaude,
René Fournet,
Valérie Warth,
Frédérique Battin-Leclerc
Abstract:
In the context of the search for gasoline surrogates for kinetic modeling purpose, this paper describes a new model for the low-temperature auto-ignition of n-heptane/iso-octane/hexene/toluene blends for the different linear isomers of hexene. The model simulates satisfactory experimental results obtained in a rapid compression machine for temperatures ranging from 650 to 850 K in the case of bi…
▽ More
In the context of the search for gasoline surrogates for kinetic modeling purpose, this paper describes a new model for the low-temperature auto-ignition of n-heptane/iso-octane/hexene/toluene blends for the different linear isomers of hexene. The model simulates satisfactory experimental results obtained in a rapid compression machine for temperatures ranging from 650 to 850 K in the case of binary and ternary mixtures including iso octane, 1-hexene and toluene. Predictive simulations have also been performed for the autoignition of n heptane/iso octane/hexene/toluene quaternary mixtures: the predicted reactivity is close to that of pure iso octane with a retarding effect when going from 1- to 3-alkene.
△ Less
Submitted 20 April, 2009;
originally announced April 2009.
-
A Lean Methane Prelixed Laminar Flame Doped witg Components of Diesel Fuel. Part I: n)Butylbenzene
Authors:
Emir Pousse,
Pierre-Alexandre Glaude,
René Fournet,
Frédérique Battin-Leclerc
Abstract:
To better understand the chemistry involved during the combustion of components of diesel fuel, the structure of a laminar lean premixed methane flame doped with n-butylbenzene has been investigated. The inlet gases contained 7.1% (molar) of methane, 36.8% of oxygen and 0.96% of n-butylbenzene corresponding to an equivalence ratio of 0.74 and a ratio C10H14 / CH4 of 13.5%. The flame has been sta…
▽ More
To better understand the chemistry involved during the combustion of components of diesel fuel, the structure of a laminar lean premixed methane flame doped with n-butylbenzene has been investigated. The inlet gases contained 7.1% (molar) of methane, 36.8% of oxygen and 0.96% of n-butylbenzene corresponding to an equivalence ratio of 0.74 and a ratio C10H14 / CH4 of 13.5%. The flame has been stabilized on a burner at a pressure of 6.7 kPa using argon as diluent, with a gas velocity at the burner of 49.2 cm/s at 333 K. Quantified species included the usual methane C0-C2 combustion products, but also 16 C3-C5 hydrocarbons, 7 C1-C3 oxygenated compounds, as well as 20 aromatic products, namely benzene, toluene, phenylacetylene, styrene, ethylbenzene, xylenes, allylbenzene, propylbenzene, cumene, methylstyrenes, butenylbenzenes, indene, indane, naphthalene, phenol, benzaldehyde, anisole, benzylalcohol, benzofuran, and isomers of C10H10 (1-methylindene, dihydronaphtalene, butadienylbenzene). A new mechanism for the oxidation of n-butylbenzene is proposed whose predictions are in satisfactory agreement with measured species profiles in flames and flow reactor experiments. The main reaction pathways of consumption of n butylbenzene have been derived from flow rate analyses.
△ Less
Submitted 28 March, 2009;
originally announced March 2009.
-
Formation of aromatics in rich methane flames doped by unsaturated compounds
Authors:
Hadj-Ali Gueniche,
Pierre-Alexandre Glaude,
René Fournet,
Frédérique Battin-Leclerc
Abstract:
In order to better understand the importance of the different channels leading to the first aromatic ring, we have investigated, the structure of a laminar rich premixed methane flame doped with several unsaturated hydrocarbons: allene and propyne, as they are precursors of propargyl radicals, which are well known as having an important role in forming benzene, 1,3-butadiene, to put in evidence…
▽ More
In order to better understand the importance of the different channels leading to the first aromatic ring, we have investigated, the structure of a laminar rich premixed methane flame doped with several unsaturated hydrocarbons: allene and propyne, as they are precursors of propargyl radicals, which are well known as having an important role in forming benzene, 1,3-butadiene, to put in evidence a possible production of benzene due to reactions of C4 compounds, and, finally, cyclopentene, which is a source of cyclopentadienyl methylene radicals which are supposed to easily isomerizes to give benzene. A ratio additive / CH4 of 16 % and an equivalence ratio of 1.79 have been used. These flames have been stabilized on a burner at a pressure of 6.7 kPa using argon as dilutant. A new mechanism for the oxidation of allene, propyne, 1,3 butadiene and cyclopentene has been proposed including the formation and decomposition of benzene and toluene. The main reaction pathways of formation of aromatics have been derived from flow rate analyses and have been compared for the three types of additives.
△ Less
Submitted 28 March, 2009;
originally announced March 2009.
-
Experimental study of the structure of a lean premixed indane/CH4/O2/Ar flame
Authors:
Emir Pousse,
Pierre-Alexandre Glaude,
René Fournet,
Frédérique Battin-Leclerc
Abstract:
In order to better understand the chemistry involved during the combustion of components of diesel fuel, the structure of a laminar lean premixed methane flame doped with indane has been investigated. The gases of this flame contains 7.1% (molar) of methane, 36.8% of oxygen and 0.90% of indane corresponding to an equivalence ratio of 0.74 and a ratio C9H10/CH4 of 12.75%. The flame has been stabi…
▽ More
In order to better understand the chemistry involved during the combustion of components of diesel fuel, the structure of a laminar lean premixed methane flame doped with indane has been investigated. The gases of this flame contains 7.1% (molar) of methane, 36.8% of oxygen and 0.90% of indane corresponding to an equivalence ratio of 0.74 and a ratio C9H10/CH4 of 12.75%. The flame has been stabilized on a burner at a pressure of 6.7 kPa using argon as dilutant, with a gas velocity at the burner of 49.2 cm/s at 333 K. Quantified species included usual methane C0-C2 combustion products, but also 11 C3-C5 hydrocarbons and 3 C1-C3 oxygenated compounds, as well as 17 aromatic products, namely benzene, toluene, phenylacetylene, styrene, ethylbenzene, xylenes, trimethylbenzenes, ethyltoluenes, indene methylindane, methylindene, naphthalene, phenol, benzaldehyde, benzofuran. The temperature was measured thanks to a thermocouple in PtRh (6%)-PtRh (30%) settled inside the enclosure and ranged from 800 K close to the burner up to 2000 K in the burned gases.
△ Less
Submitted 25 March, 2009;
originally announced March 2009.
-
Influence of the position of the double bond on the autoignition of linear alkenes at low temperature
Authors:
Roda Bounaceur,
Valérie Warth,
Baptiste Sirjean,
Pierre-Alexandre Glaude,
René Fournet,
Frédérique Battin-Leclerc
Abstract:
The influence of the position of the double bond on the autoignition...
The influence of the position of the double bond on the autoignition...
△ Less
Submitted 22 March, 2009;
originally announced March 2009.
-
Theoretical kinetic study of thermal unimolecular decomposition of cyclic alkyl radicals
Authors:
Baptiste Sirjean,
Pierre-Alexandre Glaude,
M. F. Ruiz-Lopez,
René Fournet
Abstract:
While many studies have been reported on the reactions of aliphatic hydrocarbons, the chemistry of cyclic hydrocarbons has not been explored extensively. In the present work, a theoretical study of the gas-phase unimolecular decomposition of cyclic alkyl radicals was performed by means of quantum chemical calculations at the CBS-QB3 level of theory. Energy barrier and high-pressure limit rate co…
▽ More
While many studies have been reported on the reactions of aliphatic hydrocarbons, the chemistry of cyclic hydrocarbons has not been explored extensively. In the present work, a theoretical study of the gas-phase unimolecular decomposition of cyclic alkyl radicals was performed by means of quantum chemical calculations at the CBS-QB3 level of theory. Energy barrier and high-pressure limit rate constants were calculated systematically. Thermochemical data were obtained from isodesmic reactions and the contribution of hindered rotors was taken into account. Classical transition state ...
△ Less
Submitted 7 January, 2009;
originally announced January 2009.
-
Rich methane laminar flames doped with light unsaturated hydrocarbons. Part III : cyclopentene
Authors:
Hadj-Ali Gueniche,
Pierre-Alexandre Glaude,
René Fournet,
Frédérique Battin-Leclerc
Abstract:
In line with the studies presented in the parts I and II of this paper, the structure of a laminar rich premixed methane flame doped with cyclopentene has been investigated. The gases of this flame contains 15.3% (molar) of methane, 26.7% of oxygen and 2.4% cyclopentene corresponding to an equivalence ratio of 1.79 and a ratio C5H8 / CH4 of 16 %. The flame has been stabilized on a burner at a pr…
▽ More
In line with the studies presented in the parts I and II of this paper, the structure of a laminar rich premixed methane flame doped with cyclopentene has been investigated. The gases of this flame contains 15.3% (molar) of methane, 26.7% of oxygen and 2.4% cyclopentene corresponding to an equivalence ratio of 1.79 and a ratio C5H8 / CH4 of 16 %. The flame has been stabilized on a burner at a pressure of 6.7 kPa using argon as dilutant, with a gas velocity at the burner of 36 cm/s at 333 K. The temperature ranged from 627 K close to the burner up to 2027 K. Quantified species included usual methane C0-C2 combustion products, but also propyne, allene, propene, propane, 1-butene, 1,3-butadiene, 1,2-butadiene, vinylacetylene, diacetylene, cyclopentadiene, 1,3-pentadiene, benzene and toluene. A new mechanism for the oxidation of cyclopentene has been proposed. The main reaction pathways of consumption of cyclopentene and of formation of benzene and toluene have been derived from flow rate analyses.
△ Less
Submitted 10 December, 2007;
originally announced December 2007.
-
Rich methane laminar flames doped with light unsaturated hydrocarbons. Part II: 1,3butadiene
Authors:
Hadj-Ali Gueniche,
Pierre-Alexandre Glaude,
René Fournet,
Frédérique Battin-Leclerc
Abstract:
In line with the study presented in the part I of this paper, the structure of a laminar rich premixed methane flame doped with 1,3-butadiene has been investigated. The flame contains 20.7% (molar) of methane, 31.4% of oxygen and 3.3% of 1,3-butadiene, corresponding to an equivalence ratio of 1.8, and a ratio C4H6 / CH4 of 16 %. The flame has been stabilized on a burner at a pressure of 6.7 kPa…
▽ More
In line with the study presented in the part I of this paper, the structure of a laminar rich premixed methane flame doped with 1,3-butadiene has been investigated. The flame contains 20.7% (molar) of methane, 31.4% of oxygen and 3.3% of 1,3-butadiene, corresponding to an equivalence ratio of 1.8, and a ratio C4H6 / CH4 of 16 %. The flame has been stabilized on a burner at a pressure of 6.7 kPa using argon as dilutant, with a gas velocity at the burner of 36 cm/s at 333 K. The temperature ranged from 600 K close to the burner up to 2150 K. Quantified species included usual methane C0-C2 combustion products and 1,3-butadiene, but also propyne, allene, propene, propane, 1,2-butadiene, butynes, vinylacetylene, diacetylene, 1,3-pentadiene, 2-methyl-1,3-butadiene (isoprene), 1-pentene, 3-methyl-1-butene, benzene and toluene. In order to model these new results, some improvements have been made to a mechanism previously developed in our laboratory for the reactions of C3-C4 unsaturated hydrocarbons. The main reaction pathways of consumption of 1,3-butadiene and of formation of C6 aromatic species have been derived from flow rate analyses. In this case, the C4 route to benzene formation plays an important role in comparison to the C3 pathway.
△ Less
Submitted 27 September, 2007;
originally announced September 2007.
-
Experimental study of the structure of rich premixed 1,3-butadiene/CH4/O2/Ar flame
Authors:
Hadj-Ali Gueniche,
Pierre-Alexandre Glaude,
René Fournet,
Frédérique Battin-Leclerc
Abstract:
The structure of a laminar rich premixed 1,3-C4H6/CH4/O2/Ar flame have been investigated. 1,3-Butadiene, methane, oxygen and argon mole fractions are 0.033; 0.2073; 0.3315, and 0.4280, respectively, for an equivalent ratio of 1.80. The flame has been stabilized on a burner at a pressure of 6.7 kPa (50 Torr). The concentration profiles of stable species were measured by gas chromatography after s…
▽ More
The structure of a laminar rich premixed 1,3-C4H6/CH4/O2/Ar flame have been investigated. 1,3-Butadiene, methane, oxygen and argon mole fractions are 0.033; 0.2073; 0.3315, and 0.4280, respectively, for an equivalent ratio of 1.80. The flame has been stabilized on a burner at a pressure of 6.7 kPa (50 Torr). The concentration profiles of stable species were measured by gas chromatography after sampling with a quartz probe. Quantified species included carbon monoxide and dioxide, methane, oxygen, hydrogen, ethane, ethylene, acetylene, propyne, allene, propene, cyclopropane, 1,3-butadiene, butenes, 1-butyne, vinylacetylene, diacetylene, C5 compounds, benzene, and toluene. The temperature was measured thanks to a thermocouple in PtRh (6%)-PtRh (30%) settled inside the enclosure and ranged from 900 K close to the burner up to 2100 K.
△ Less
Submitted 14 June, 2007;
originally announced June 2007.
-
Primary reactions of the thermal decomposition of tricyclodecane
Authors:
Olivier Herbinet,
Baptiste Sirjean,
Roda Bounaceur,
René Fournet,
Frédérique Battin-Leclerc,
Gérard Scacchi,
Paul-Marie Marquaire
Abstract:
In order to better understand the thermal decomposition of polycyclanes, the pyrolysis of tricyclodecane has been studied in a jet-stirred reactor at temperatures from 848 to 933 K, for residence times between 0.5 and 6 s and at atmospheric pressure, in order to obtain a conversion between 0.01 and 25 %. The main products of the reaction are hydrogen, methane, ethylene, ethane, propene, 1,3-cycl…
▽ More
In order to better understand the thermal decomposition of polycyclanes, the pyrolysis of tricyclodecane has been studied in a jet-stirred reactor at temperatures from 848 to 933 K, for residence times between 0.5 and 6 s and at atmospheric pressure, in order to obtain a conversion between 0.01 and 25 %. The main products of the reaction are hydrogen, methane, ethylene, ethane, propene, 1,3-cyclopentadiene, cyclopentene, benzene, 1,5-hexadiene, toluene and 3-cyclopentyl-cyclopentene. A primary mechanism containing all the possible initiation steps, including those involving diradicals, as well as propagation reactions has been developed and allows experimental results to be satisfactorily modeled. The main reaction pathways of consumption of tricyclodecane and of formation of the main products have been derived from flow rate and sensitivity analyses.
△ Less
Submitted 14 June, 2007;
originally announced June 2007.
-
Modelling of the gas-phase oxidation of cyclohexane
Authors:
Frédéric Buda,
Barbara Heyberger,
René Fournet,
Pierre-Alexandre Glaude,
Valérie Warth,
Frédérique Battin-Leclerc
Abstract:
This paper presents a modeling study of the oxidation of cyclohexane from low to intermediate temperature (650-1050 K), including the negative temperature coefficient (NTC) zone. A detailed kinetic mechanism has been developed using computer-aided generation. This comprehensive low-temperature mechanism involves 513 species and 2446 reactions and includes two additions of cyclohexyl radicals to…
▽ More
This paper presents a modeling study of the oxidation of cyclohexane from low to intermediate temperature (650-1050 K), including the negative temperature coefficient (NTC) zone. A detailed kinetic mechanism has been developed using computer-aided generation. This comprehensive low-temperature mechanism involves 513 species and 2446 reactions and includes two additions of cyclohexyl radicals to oxygen, as well as subsequent reactions. The rate constants of the reactions involving the formation of bicyclic species (isomerizations, formation of cyclic ethers) have been evaluated from literature data. This mechanism is able to satisfactorily reproduce experimental results obtained in a rapid-compression machine for temperatures ranging from 650 to 900 K and in a jet-stirred reactor from 750 to 1050 K. Flow-rate analyses have been performed at low and intermediate temperatures.
△ Less
Submitted 14 June, 2007;
originally announced June 2007.
-
Kinetic modelling of a surrogate diesel fuel applied to 3D auto-ignition in HCCI engines
Authors:
Roda Bounaceur,
Pierre-Alexandre Glaude,
René Fournet,
Frédérique Battin-Leclerc,
S. Jay,
A. Pires Da Cruz
Abstract:
The prediction of auto-ignition delay times in HCCI engines has risen interest on detailed chemical models. This paper described a validated kinetic mechanism for the oxidation of a model Diesel fuel (n-decane and α-methylnaphthalene). The 3D model for the description of low and high temperature auto-ignition in engines is presented. The behavior of the model fuel is compared with that of n…
▽ More
The prediction of auto-ignition delay times in HCCI engines has risen interest on detailed chemical models. This paper described a validated kinetic mechanism for the oxidation of a model Diesel fuel (n-decane and α-methylnaphthalene). The 3D model for the description of low and high temperature auto-ignition in engines is presented. The behavior of the model fuel is compared with that of n-heptane. Simulations show that the 3D model coupled with the kinetic mechanism can reproduce experimental HCCI and Diesel engine results and that the correct modeling of auto-ignition in the cool flame region is essential in HCCI conditions.
△ Less
Submitted 14 June, 2007;
originally announced June 2007.
-
Extension of the composite CBS-QB3 method to singlet diradical calculations
Authors:
Baptiste Sirjean,
René Fournet,
Pierre-Alexandre Glaude,
M. F. Ruiz-Lopez
Abstract:
The composite CBS-QB3 method is widely used to obtain accurate energies of molecules and radicals although its use in the case of singlet diradicals gives rise to some difficulties. The problem is related to the parameterized correction this method introduces to account for spin-contamination. We report a new term specifically designed to describe singlet diradicals separated by at least one CH2…
▽ More
The composite CBS-QB3 method is widely used to obtain accurate energies of molecules and radicals although its use in the case of singlet diradicals gives rise to some difficulties. The problem is related to the parameterized correction this method introduces to account for spin-contamination. We report a new term specifically designed to describe singlet diradicals separated by at least one CH2 unit. As a test case, we have computed the formation enthalpy of a series of diradicals that includes hydrocarbons as well as systems involving heteroatoms (nitrogen, oxygen). The resulting CBS-QB3 energies are very close to experiment.
△ Less
Submitted 14 June, 2007;
originally announced June 2007.
-
The autoignition of cyclopentane and cyclohexane in a shock tube
Authors:
Baptiste Sirjean,
Frédéric Buda,
Hichem Hakka,
Pierre-Alexandre Glaude,
René Fournet,
Valérie Warth,
Frédérique Battin-Leclerc
Abstract:
Ignition delay times of cyclohexane-oxygen-argon and cyclopentane-oxygen-argon mixtures have been measured in a shock tube, the onset of ignition being detected by OH radical emission. Mixtures contained 0.5 or 1 % of hydrocarbon for equivalence ratios ranging from 0.5 to 2. Reflected shock waves allowed temperatures from 1230 to 1800 K and pressures from 7.3 to 9.5 atm to be obtained. These mea…
▽ More
Ignition delay times of cyclohexane-oxygen-argon and cyclopentane-oxygen-argon mixtures have been measured in a shock tube, the onset of ignition being detected by OH radical emission. Mixtures contained 0.5 or 1 % of hydrocarbon for equivalence ratios ranging from 0.5 to 2. Reflected shock waves allowed temperatures from 1230 to 1800 K and pressures from 7.3 to 9.5 atm to be obtained. These measurements have shown that cyclopentane is much less reactive than cyclohexane, as for a given temperature the observed autoignition delay times were about ten times higher for the C5 compound compared to the C6. Detailed mechanisms for the combustion of cyclohexane and cyclopentane have been proposed to reproduce these results. The elementary steps included in the kinetic models of the oxidation of cyclanes are close to those proposed to describe the oxidation of acyclic alkanes and alkenes. Consequently, it has been possible to obtain these models by using an improved version of software EXGAS, a computer package developed to perform the automatic generation of detailed kinetic models for the gas-phase oxidation and combustion of linear and branched alkanes and alkenes. Nevertheless, the modelling of the oxidation of cyclanes requires to consider new types of generic reactions, and especially to define new correlations for the estimation of the rate constants. Ab initio calculations have been used to better know some of the rate constants used in the case of cyclopentane. The main reaction pathways have been derived from flow rate and sensitivity analyses.
△ Less
Submitted 14 June, 2007;
originally announced June 2007.
-
Thermal stability of n-dodecane : experiments and kinetic modelling
Authors:
Olivier Herbinet,
Paul-Marie Marquaire,
Frédérique Battin-Leclerc,
René Fournet
Abstract:
The thermal decomposition of n-dodecane, a component of some jet fuels, has been studied in a jet-stirred reactor at temperatures from 793 to 1093 K, for residence times between 1 and 5 s and at atmospheric pressure. Thermal decomposition of hydrocarbon fuel prior the entrance in the combustion chamber is an envisaged way to cool the wall of hypersonic vehicles. The products of the reaction are…
▽ More
The thermal decomposition of n-dodecane, a component of some jet fuels, has been studied in a jet-stirred reactor at temperatures from 793 to 1093 K, for residence times between 1 and 5 s and at atmospheric pressure. Thermal decomposition of hydrocarbon fuel prior the entrance in the combustion chamber is an envisaged way to cool the wall of hypersonic vehicles. The products of the reaction are mainly hydrogen, methane, ethane, 1,3-butadiene and 1-alkenes from ethylene to 1-undecene. For higher temperatures and residence times acetylene, allene, propyne, cyclopentene, 1,3-cyclopentadiene and aromatic compounds from benzene to pyrene through naphthalene have also been observed. A previous detailed kinetic model of the thermal decomposition of n-dodecane generated using EXGAS software has been improved and completed by a sub-mechanism explaining the formation and the consumption of aromatic compounds.
△ Less
Submitted 14 June, 2007;
originally announced June 2007.
-
Detailed kinetic study of the ring opening of cycloalkanes by CBS-QB3 calculations
Authors:
Baptiste Sirjean,
Pierre-Alexandre Glaude,
M. F. Ruiz-Lopez,
René Fournet
Abstract:
This work reports a theoretical study of the gas phase unimolecular decomposition of cyclobutane, cyclopentane and cyclohexane by means of quantum chemical calculations. A biradical mechanism has been envisaged for each cycloalkane, and the main routes for the decomposition of the biradicals formed have been investigated at the CBS-QB3 level of theory. Thermochemical data (δH^0_f, S^0, C^0_p) fo…
▽ More
This work reports a theoretical study of the gas phase unimolecular decomposition of cyclobutane, cyclopentane and cyclohexane by means of quantum chemical calculations. A biradical mechanism has been envisaged for each cycloalkane, and the main routes for the decomposition of the biradicals formed have been investigated at the CBS-QB3 level of theory. Thermochemical data (δH^0_f, S^0, C^0_p) for all the involved species have been obtained by means of isodesmic reactions. The contribution of hindered rotors has also been included. Activation barriers of each reaction have been analyzed to assess the 1 energetically most favorable pathways for the decomposition of biradicals. Rate constants have been derived for all elementary reactions using transition state theory at 1 atm and temperatures ranging from 600 to 2000 K. Global rate constant for the decomposition of the cyclic alkanes in molecular products have been calculated. Comparison between calculated and experimental results allowed to validate the theoretical approach. An important result is that the rotational barriers between the conformers, which are usually neglected, are of importance in decomposition rate of the largest biradicals. Ring strain energies (RSE) in transition states for ring opening have been estimated and show that the main part of RSE contained in the cyclic reactants is removed upon the activation process.
△ Less
Submitted 5 April, 2007;
originally announced April 2007.
-
Thermal decomposition of norbornane (bicyclo[2.2.1]heptane) dissolved in benzene. Experimental study and mechanism investigation
Authors:
Olivier Herbinet,
Baptiste Sirjean,
Frédérique Battin-Leclerc,
René Fournet,
Paul-Marie Marquaire
Abstract:
The thermal decomposition of norbornane (dissolved in benzene) has been studied in a jet stirred reactor at temperatures between 873 and 973 K, at residence times ranging from 1 to 4 s and at atmospheric pressure, leading to conversions from 0.04 to 22.6%. 25 reaction products were identified and quantified by gas chromatography, amongst which the main ones are hydrogen, ethylene and 1,3-cyclope…
▽ More
The thermal decomposition of norbornane (dissolved in benzene) has been studied in a jet stirred reactor at temperatures between 873 and 973 K, at residence times ranging from 1 to 4 s and at atmospheric pressure, leading to conversions from 0.04 to 22.6%. 25 reaction products were identified and quantified by gas chromatography, amongst which the main ones are hydrogen, ethylene and 1,3-cyclopentadiene. A mechanism investigation of the thermal decomposition of the norbornane - benzene binary mixture has been performed. Reactions involved in the mechanism have been reviewed: unimolecular initiations 1 by C-C bond scission of norbornane, fate of the generated diradicals, reactions of transfer and propagation of norbornyl radicals, reactions of benzene and cross-coupling reactions.
△ Less
Submitted 5 April, 2007;
originally announced April 2007.
-
Rich methane premixed laminar flames doped by light unsaturated hydrocarbons - Part I : allene and propyne
Authors:
Hadj-Ali Gueniche,
Pierre-Alexandre Glaude,
Guillaume Dayma,
René Fournet,
Frédérique Battin-Leclerc
Abstract:
The structure of three laminar premixed rich flames has been investigated: a pure methane flame and two methane flames doped by allene and propyne, respectively. The gases of the three flames contain 20.9% (molar) of methane and 33.4% of oxygen, corresponding to an equivalence ratio of 1.25 for the pure methane flame. In both doped flames, 2.49% of C3H4 was added, corresponding to a ratio C3H4/C…
▽ More
The structure of three laminar premixed rich flames has been investigated: a pure methane flame and two methane flames doped by allene and propyne, respectively. The gases of the three flames contain 20.9% (molar) of methane and 33.4% of oxygen, corresponding to an equivalence ratio of 1.25 for the pure methane flame. In both doped flames, 2.49% of C3H4 was added, corresponding to a ratio C3H4/CH4 of 12% and an equivalence ratio of 1.55. The three flames have been stabilized on a burner at a pressure of 6.7 kPa using argon as dilutant, with a gas velocity at the burner of 36 cm/s at 333 K. The concentration profiles of stable species were measured by gas chromatography after sampling with a quartz microprobe. Quantified species included carbon monoxide and dioxide, methane, oxygen, hydrogen, ethane, ethylene, acetylene, propyne, allene, propene, propane, 1,2-butadiene, 1,3-butadiene, 1-butene, isobutene, 1-butyne, vinylacetylene, and benzene. The temperature was measured using a PtRh (6%)-PtRh (30%) thermocouple settled inside the enclosure and ranged from 700 K close to the burner up to 1850 K. In order to model these new results, some improvements have been made to a mechanism previously developed in our laboratory for the reactions of C3-C4 unsaturated hydrocarbons. The main reaction pathways of consumption of allene and propyne and of formation of C6 aromatic species have been derived from flow rate analyses.
△ Less
Submitted 3 April, 2007;
originally announced April 2007.
-
Experimental and modeling study of the autoignition of 1-hexene/iso-octane mixtures at low temperatures
Authors:
Guillaume Vanhove,
Rodolphe Minetti,
Sylvain Touchard,
René Fournet,
Pierre-Alexandre Glaude,
Frédérique Battin-Leclerc
Abstract:
Autoignition delay times have been measured in a rapid compression machine at Lille at temperatures after compression from 630 to 840 K, pressures from 8 to 14 bar, Φ= 1 and for a iso octane/1 hexene mixture containing 82% iso-octane and 18% 1 hexene. Results have shown that this mixture is strongly more reactive than pure iso-octane, but less reactive than pure 1 hexene. It exhibits a classical…
▽ More
Autoignition delay times have been measured in a rapid compression machine at Lille at temperatures after compression from 630 to 840 K, pressures from 8 to 14 bar, Φ= 1 and for a iso octane/1 hexene mixture containing 82% iso-octane and 18% 1 hexene. Results have shown that this mixture is strongly more reactive than pure iso-octane, but less reactive than pure 1 hexene. It exhibits a classical low temperature behaviour, with the appearance of cool flame and a negative temperature coefficient region. The composition of the reactive mixture obtained after the cool flame has also been determined. A detailed kinetic model has been obtained by using the system EXGAS, developed in Nancy for the automatic generation of kinetic mechanisms, and an acceptable agreement with the experimental results has been obtained both for autoignition delay times and for the distribution of products. A flow rate analysis reveals that the crossed reactions between species coming from both reactants (like H-abstractions or combinations) are negligible in the main flow consumption of the studied hydrocarbons. The ways of formation of the main primary products observed and the most sensitive rate constants have been identified.
△ Less
Submitted 28 March, 2006;
originally announced March 2006.
