-
Characterization of Commercial Thermoelectric Modules for Precision Heat FLux Measurement
Authors:
Jacob Crossley,
A. N. M. Taufiq Elahi,
Mohammad Ghashami,
Keunhan Park
Abstract:
In this article, we present a cost-effective approach to the precision measurement of heat flux using commercial thermoelectric modules (TEMs). Two different methods of measuring heat flux with TEMs are investigated, namely passive mode based on the Seebeck effect and active mode based on the Peltier effect. For both modes, a TEM as a heat fluxmeter is calibrated to show a linear relation between…
▽ More
In this article, we present a cost-effective approach to the precision measurement of heat flux using commercial thermoelectric modules (TEMs). Two different methods of measuring heat flux with TEMs are investigated, namely passive mode based on the Seebeck effect and active mode based on the Peltier effect. For both modes, a TEM as a heat fluxmeter is calibrated to show a linear relation between the voltage across the TEM and the heat flow rate from 0 to 100 mW. While both modes exhibit sufficiently high sensitivities suitable for low heat flow measurement, active mode is shown to be $\sim$7 times more sensitive than passive mode. From the speculation on the origin of the measurement uncertainty, we propose a dual TEM scheme by operating the top TEM in passive mode while its bottom temperature maintains constant by the feedback-controlled bottom TEM. The dual-TEM scheme can suppress the sensitivity uncertainty by up to 4 times when compared to the single-TEM passive mode by stabilizing the bottom temperature. The response time of a 1.5 cm $\times$ 1.5 cm TEM is measured to be 8.90 $\pm$ 0.97 seconds for heating and 10.83 $\pm$ 0.65 seconds for cooling, which is slower than commercial heat fluxmeters but still fast enough to measure heat flux with a time resolution on the order of 10 seconds. We believe that the obtained results can facilitate the use of a commercial TEM for heat flux measurement in various thermal experiments
△ Less
Submitted 8 August, 2022;
originally announced August 2022.
-
Revisiting the Figure of Merit of Concentrated Solar Power Receivers
Authors:
A. N. M. Taufiq Elahi,
Riley Crist,
Vahid Hatamipour,
Mathieu Francoeur,
Sameer Rao,
Keunhan Park
Abstract:
The figure of merit (FOM) is a widely used metric to characterize the performance of concentrated solar power (CSP) receivers by comparing the amount of solar thermal energy retained by the receiver to the incident concentrated solar radiation. However, the FOM is a strong function of the concentration factor and receiver temperature, thus direct comparison of FOM values measured under disparate o…
▽ More
The figure of merit (FOM) is a widely used metric to characterize the performance of concentrated solar power (CSP) receivers by comparing the amount of solar thermal energy retained by the receiver to the incident concentrated solar radiation. However, the FOM is a strong function of the concentration factor and receiver temperature, thus direct comparison of FOM values measured under disparate operating conditions is inappropriate. To remedy this problem, the present study proposes a new metric called the receiver effectiveness calculated by normalizing the actual FOM with its theoretical maximum. The receiver effectiveness can be employed for comparing receiver performances regardless of their operating conditions, and can be treated as more-like the second law efficiency of thermodynamics. In addition, a theoretical limit of the CSP plant efficiency is also examined by combining the maximum FOM and the Carnot efficiency for different concentration factors and receiver temperatures. The calculated maximum CSP plant efficiency clearly indicate that optimizing FOM does not always lead to a better CSP plant performance. Along with the FOM, the proposed receiver effectiveness and maximum CSP system efficiency should be considered as complementary metrics to evaluate the performance of the CSP system.
△ Less
Submitted 2 September, 2022; v1 submitted 4 December, 2020;
originally announced December 2020.
-
Comprehensive Energy Balance Analysis of Photon-Enhanced Thermionic Power Generation Considering Concentrated Solar Absorption Distribution
Authors:
A. N. M. Taufiq Elahi,
Mohammad Ghashami,
Devon Jensen,
Keunhan Park
Abstract:
The present article reports a comprehensive energy balance analysis of a photon-enhanced thermionic emission (PETE) device when it is used for concentrated solar power (CSP) generation. To this end, we consider a realistic PETE device composed of a boron-doped silicon emitter on glass and a phosphorus-doped diamond collector on tungsten separated by the inter-electrode vacuum gap. Depth-dependent…
▽ More
The present article reports a comprehensive energy balance analysis of a photon-enhanced thermionic emission (PETE) device when it is used for concentrated solar power (CSP) generation. To this end, we consider a realistic PETE device composed of a boron-doped silicon emitter on glass and a phosphorus-doped diamond collector on tungsten separated by the inter-electrode vacuum gap. Depth-dependent spectral solar absorption and its photovoltaic and photothermal energy conversion processes are rigorously calculated to predict the PETE power output and energy conversion efficiency. Our calculation predicts that when optimized, the power output of the considered PETE device can reach 1.6 W/cm$^2$ with the energy conversion efficiency of $\sim$18 \% for 100$\times$ solar concentration, which is substantially lower than those predicted in previous works under ideal conditions. In addition, the photon-enhancement ratio is lower than 10 and decreases with the increasing solar concentration due to the photothermal heating of the emitter, suggesting that PETE may be an adequate energy conversion process for low-to-medium CSP below $\sim$100$\times$ concentration. These observations signify the importance of a rigorous energy balance analysis based on spectral and spatial solar absorption distribution for the accurate prediction of PETE power generation.
△ Less
Submitted 25 November, 2020;
originally announced November 2020.
