-
Decommissioning and Post-Irradiation Examination of the LHC Beam Dumps
Authors:
N. Solieri,
A. Lund,
A. -P. Bernardes,
L. R. Buonocore,
A. Cherif,
S. De Man,
M. Di Castro,
S. Di Giovannantonio,
G. Dumont,
S. El-Idrissi,
E. Farina,
D. Grenier,
E. Grenier-Boley,
M. Himmerlich,
A. Infantino,
A. Lechner,
R. Mouret,
D. Pazem,
A. T. Perez-Fontenla,
E. Romagnoli,
S. Sgobba,
C. Tromel,
C. Veiga Almagro,
M. Calviani
Abstract:
The LHC beam dumps are responsible for the safe absorption of the Large Hadron Collider (LHC) particle beams. In 2018, the two 6.4-tonne beam dumps that had been in operation since the LHC's startup in 2008 were removed and replaced with upgraded versions. Endoscopic inspections of these beam dumps and experimental high-intensity proton-beam irradiation of material samples raised concerns about th…
▽ More
The LHC beam dumps are responsible for the safe absorption of the Large Hadron Collider (LHC) particle beams. In 2018, the two 6.4-tonne beam dumps that had been in operation since the LHC's startup in 2008 were removed and replaced with upgraded versions. Endoscopic inspections of these beam dumps and experimental high-intensity proton-beam irradiation of material samples raised concerns about the structural integrity of the carbon-based materials in their cores. It was therefore decided to undertake an accelerated project of dismantling and post-irradiation examination of the removed dumps as part of a wider program of work to ensure the safe operation of the LHC beam dumps in the coming years. This paper describes the decommissioning process for the two beam dumps carried out at CERN between 2021 and 2023, covering the preparatory studies, practical challenges encountered, and solutions implemented. It details the establishment of an operational framework, including the preparation of the working environment, the development of a method for cutting the irradiated 12-mm-thick duplex stainless-steel vessel, and the cut sequencing. Additionally, the paper presents the findings derived from the post-irradiation examination of the different carbon-based core materials subjected to deposited energy densities up to 1.5 kJ/g. The extruded graphite plates within the vessel exhibited a cracking pattern, which was likely due to the dynamic response of the device upon beam impact, and their retaining rings were found to be displaced. Despite minor signs of surface deterioration, the expanded graphite sheets were intact, and the isostatic graphite blocks showed no evidence of material degradation.
△ Less
Submitted 7 May, 2025;
originally announced May 2025.
-
Coherent Optomechanical State Transfer between Disparate Mechanical Resonators
Authors:
Matthew J. Weaver,
Frank M. Buters,
Fernando Luna,
Hedwig J. Eerkens,
Kier Heeck,
Sven de Man,
Dirk Bouwmeester
Abstract:
Hybrid quantum systems have been developed with various mechanical, optical and microwave harmonic oscillators. The coupling produces a rich library of interactions including two mode squeezing, swapping interactions, back-action evasion and thermal control. In a multimode mechanical system, coupling resonators of different scales (both in frequency and mass) leverages the advantages of each reson…
▽ More
Hybrid quantum systems have been developed with various mechanical, optical and microwave harmonic oscillators. The coupling produces a rich library of interactions including two mode squeezing, swapping interactions, back-action evasion and thermal control. In a multimode mechanical system, coupling resonators of different scales (both in frequency and mass) leverages the advantages of each resonance. For example: a high frequency, easily manipulated resonator could be entangled with a low frequency massive object for tests of gravitational decoherence. Here we demonstrate coherent optomechanical state swapping between two spatially and frequency separated resonators with a mass ratio of 4. We find that, by using two laser beams far detuned from an optical cavity resonance, efficient state transfer is possible through a process very similar to STIRAP (Stimulated Raman Adiabatic Passage) in atomic physics. Although the demonstration is classical, the same technique can be used to generate entanglement between oscillators in the quantum regime.
△ Less
Submitted 7 April, 2017;
originally announced April 2017.
-
High-Q nested resonator in an actively stabilized optomechanical cavity
Authors:
Frank M. Buters,
Kier Heeck,
Hedwig J. Eerkens,
Matthew J. Weaver,
Fernando Luna,
Sven de Man,
Dirk Bouwmeester
Abstract:
Experiments involving micro- and nanomechanical resonators need to be carefully designed to reduce mechanical environmental noise. A small scale on-chip approach is to add an additional resonator to the system as a mechanical low-pass filter. Unfortunately, the inherent low frequency of the low-pass filter causes the system to be easily excited mechanically. Fixating the additional resonator ensur…
▽ More
Experiments involving micro- and nanomechanical resonators need to be carefully designed to reduce mechanical environmental noise. A small scale on-chip approach is to add an additional resonator to the system as a mechanical low-pass filter. Unfortunately, the inherent low frequency of the low-pass filter causes the system to be easily excited mechanically. Fixating the additional resonator ensures that the resonator itself can not be excited by the environment. This, however, negates the purpose of the low-pass filter. We solve this apparent paradox by applying active feedback to the resonator, thereby minimizing the motion with respect the front mirror of an optomechanical cavity. Not only does this method actively stabilize the cavity length, but it also retains the on-chip vibration isolation.
△ Less
Submitted 23 January, 2017; v1 submitted 16 January, 2017;
originally announced January 2017.
-
Nested Trampoline Resonators for Optomechanics
Authors:
Matthew J. Weaver,
Brian Pepper,
Fernando Luna,
Frank M. Buters,
Hedwig J. Eerkens,
Gesa Welker,
Blaise Perock,
Kier Heeck,
Sven de Man,
Dirk Bouwmeester
Abstract:
Two major challenges in the development of optomechanical devices are achieving a low mechanical and optical loss rate and vibration isolation from the environment. We address both issues by fabricating trampoline resonators made from low pressure chemical vapor deposition (LPCVD) Si$_3$N$_4$ with a distributed bragg reflector (DBR) mirror. We design a nested double resonator structure with 80 dB…
▽ More
Two major challenges in the development of optomechanical devices are achieving a low mechanical and optical loss rate and vibration isolation from the environment. We address both issues by fabricating trampoline resonators made from low pressure chemical vapor deposition (LPCVD) Si$_3$N$_4$ with a distributed bragg reflector (DBR) mirror. We design a nested double resonator structure with 80 dB of mechanical isolation from the mounting surface at the inner resonator frequency, and we demonstrate up to 45 dB of isolation at lower frequencies in agreement with the design. We reliably fabricate devices with mechanical quality factors of around 400,000 at room temperature. In addition these devices were used to form optical cavities with finesse up to 181,000 $\pm$ 1,000. These promising parameters will enable experiments in the quantum regime with macroscopic mechanical resonators.
△ Less
Submitted 6 January, 2016; v1 submitted 1 October, 2015;
originally announced October 2015.
-
Experimental exploration of the optomechanical attractor diagram and its dynamics
Authors:
Frank M. Buters,
Hedwig J. Eerkens,
Kier Heeck,
Matthew J. Weaver,
Brian Pepper,
Sven de Man,
Dirk Bouwmeester
Abstract:
We demonstrate experimental exploration of the attractor diagram of an optomechanical system where the optical forces compensate for the mechanical losses. In this case stable self-induced oscillations occur but only for specific mirror amplitudes and laser detunings. We demonstrate that we can amplify the mechanical mode to an amplitude 500 times larger than the thermal amplitude at 300K. The lac…
▽ More
We demonstrate experimental exploration of the attractor diagram of an optomechanical system where the optical forces compensate for the mechanical losses. In this case stable self-induced oscillations occur but only for specific mirror amplitudes and laser detunings. We demonstrate that we can amplify the mechanical mode to an amplitude 500 times larger than the thermal amplitude at 300K. The lack of unstable or chaotic motion allows us to manipulate our system into a non-trivial steady state and explore the dynamics of self-induced oscillations in great detail.
△ Less
Submitted 23 April, 2015;
originally announced April 2015.
-
Measurement of the Casimir force with a ferrule-top sensor
Authors:
P. Zuurbier,
S. de Man,
G. Gruca,
K. Heeck,
D. Iannuzzi
Abstract:
We present a Casimir force setup based on an all-optical ferrule-top sensor. We demonstrate that the instrument can be used to measure the gradient of the Casimir force between a gold coated sphere and a gold coated plate with results that are comparable to those achieved by similar atomic force microscope experiments. Thanks to the monolithic design of the force sensor (which does not require any…
▽ More
We present a Casimir force setup based on an all-optical ferrule-top sensor. We demonstrate that the instrument can be used to measure the gradient of the Casimir force between a gold coated sphere and a gold coated plate with results that are comparable to those achieved by similar atomic force microscope experiments. Thanks to the monolithic design of the force sensor (which does not require any optical triangulation readout) and to the absence of electronics on the sensing head, the instrument represents a significant step ahead for future studies of the Casimir effect under engineered conditions, where the intervening medium or the environmental conditions might be unsuitable for the use of more standard setups.
△ Less
Submitted 15 February, 2011;
originally announced February 2011.
-
Halving the Casimir force with conductive oxides: experimental details
Authors:
Sven de Man,
Kier Heeck,
Davide Iannuzzi
Abstract:
This work is an extended version of a paper published last year in Physical Review Letters [S. de Man et al., Phys. Rev. Lett. 103, 040402 (2009)], where we presented measurements of the Casimir force between a gold coated sphere and a plate coated with either gold or an indium-tin-oxide (ITO) layer. The experiment, which was performed in air, showed that ITO is sufficiently conducting to prevent…
▽ More
This work is an extended version of a paper published last year in Physical Review Letters [S. de Man et al., Phys. Rev. Lett. 103, 040402 (2009)], where we presented measurements of the Casimir force between a gold coated sphere and a plate coated with either gold or an indium-tin-oxide (ITO) layer. The experiment, which was performed in air, showed that ITO is sufficiently conducting to prevent charge accumulation, but still transparent enough to halve the Casimir attraction when compared to gold. Here, we report all the experimental details that, due to the limited space available, were omitted in the previous article. We discuss the performance of our setup in terms of stability of the calibration procedure and reproducibility of the Casimir force measurement. We also introduce and demonstrate a new technique to obtain the spring constant of our force sensor. Furthermore, we present a thorough description of the experimental method, a comprehensive explanation of data elaboration and error analysis, and a complete characterization of the dielectric function and of the surface roughness of the samples used in the actual experiment.
△ Less
Submitted 17 December, 2010;
originally announced December 2010.
