In-plane anisotropic optical and mechanical properties of two-dimensional MoO$_3$
Authors:
Sergio Puebla,
Roberto D'Agosta,
Gabriel Sanchez-Santolino,
Riccardo Frisenda,
Carmen Munuera,
Andres Castellanos-Gomez
Abstract:
Molybdenum trioxide (MoO$_3$) in-plane anisotropy has increasingly attracted the attention of the scientific community in the last few years. Many of the observed in-plane anisotropic properties stem from the anisotropic refractive index and elastic constants of the material but a comprehensive analysis of these fundamental properties is still lacking. Here we employ Raman and micro-reflectance me…
▽ More
Molybdenum trioxide (MoO$_3$) in-plane anisotropy has increasingly attracted the attention of the scientific community in the last few years. Many of the observed in-plane anisotropic properties stem from the anisotropic refractive index and elastic constants of the material but a comprehensive analysis of these fundamental properties is still lacking. Here we employ Raman and micro-reflectance measurements, using polarized light, to determine the angular dependence of the refractive index of thin MoO$_3$ flakes and we study the directional dependence of the MoO$_3$ Young's modulus using the buckling metrology method. We found that MoO$_3$ displays one of the largest in-plane anisotropic mechanical properties reported for 2D materials so far.
△ Less
Submitted 7 May, 2021;
originally announced May 2021.
Tunable Photodetectors via in situ Thermal Conversion of TiS$_3$ to TiO$_2$
Authors:
Foad Ghasemi,
Riccardo Frisenda,
Eduardo Flores,
Nikos Papadopoulos,
Robert Biele,
David Perez de Lara,
Herre S. J. van der Zant,
Kenji Watanabe,
Takashi Taniguchi,
Roberto D'Agosta,
Jose R. Ares,
Carlos Sánchez,
Isabel J. Ferrer,
Andres Castellanos-Gomez
Abstract:
In two-dimensional materials research, oxidation is usually considered as a common source for the degradation of electronic and optoelectronic devices or even device failure. However, in some cases a controlled oxidation can open the possibility to widely tune the band structure of 2D materials. In particular, we demonstrate the controlled oxidation of titanium trisulfide (TiS$_3$), a layered semi…
▽ More
In two-dimensional materials research, oxidation is usually considered as a common source for the degradation of electronic and optoelectronic devices or even device failure. However, in some cases a controlled oxidation can open the possibility to widely tune the band structure of 2D materials. In particular, we demonstrate the controlled oxidation of titanium trisulfide (TiS$_3$), a layered semiconductor that has attracted much attention recently thanks to its quasi-1D electronic and optoelectronic properties and its direct bandgap of 1.1 eV. Heating TiS$_3$ in air above 300 °C gradually converts it into TiO$_2$, a semiconductor with a wide bandgap of 3.2 eV with ap-plications in photo-electrochemistry and catalysis. In this work, we investigate the controlled thermal oxidation of individual TiS$_3$ nanoribbons and its influence on the optoelectronic properties of TiS$_3$-based photodetectors. We observe a step-wise change in the cut-off wavelength from its pristine value ~1000 nm to 450 nm after subjecting the TiS$_3$ devices to subsequent thermal treatment cycles. Ab-initio and many-body calculations confirm an increase in the bandgap of titanium oxysulfide (TiO$_{2-x}$S$_x$) when increasing the amount of oxygen and reducing the amount of sulfur.
△ Less
Submitted 11 June, 2020;
originally announced June 2020.
