Development of cooling system of solid state target for irradiation under proton beam of C18 cyclotron
Authors:
A. Avetisyan,
R. Dallakyan,
N. Dobrovolski,
A. Manukyan,
A. Melkonyan,
I. Sinenko
Abstract:
In recent years, the possibility of direct production of the 99mTc isotope (bypassing the parent 99Mo stage) for medical purposes using nuclear reactions on charged particle beams has been actively discussed around the world [1,2]. At A.I. Alikhanyan National Science Laboratory (Yerevan Physics Institute), an activity is underway to develop a technology for producing the 99mTc isotope by irradiati…
▽ More
In recent years, the possibility of direct production of the 99mTc isotope (bypassing the parent 99Mo stage) for medical purposes using nuclear reactions on charged particle beams has been actively discussed around the world [1,2]. At A.I. Alikhanyan National Science Laboratory (Yerevan Physics Institute), an activity is underway to develop a technology for producing the 99mTc isotope by irradiating a molybdenum target of 100Mo, pressed into a titanium base, with a proton beam of a C18 cyclotron [3,4,5]. One of the limitations of this technique is the utilization of heat released in the target as a result of proton energy loss [6,7]. The task of this work was the improvement of the thermal regime of a standard target for the C18 cyclotron due to a series of parallel grooves. Heat transfer experiments with prototypes of targets were carried out on a specially made test bench providing water cooling of its back side. A special Plexiglas thermal block was made to study the thermal processes in the target. The measurement results show that the above mentioned technique of processing the base of the target leads to a significant increase in the rate of cooling of the target, which will allow to irradiate at significantly higher proton beam intensities, which in its turn will increase the irradiation efficiency and reduce the cost of the final product.
△ Less
Submitted 26 October, 2020; v1 submitted 14 October, 2020;
originally announced October 2020.
The OLYMPUS Experiment
Authors:
R. Milner,
D. K. Hasell,
M. Kohl,
U. Schneekloth,
N. Akopov,
R. Alarcon,
V. A. Andreev,
O. Ates,
A. Avetisyan,
D. Bayadilov,
R. Beck,
S. Belostotski,
J. C. Bernauer,
J. Bessuille,
F. Brinker,
B. Buck,
J. R. Calarco,
V. Carassiti,
E. Cisbani,
G. Ciullo,
M. Contalbrigo,
N. D'Ascenzo,
R. De Leo,
J. Diefenbach,
T. W. Donnelly
, et al. (48 additional authors not shown)
Abstract:
The OLYMPUS experiment was designed to measure the ratio between the positron-proton and electron-proton elastic scattering cross sections, with the goal of determining the contribution of two-photon exchange to the elastic cross section. Two-photon exchange might resolve the discrepancy between measurements of the proton form factor ratio, $μ_p G^p_E/G^p_M$, made using polarization techniques and…
▽ More
The OLYMPUS experiment was designed to measure the ratio between the positron-proton and electron-proton elastic scattering cross sections, with the goal of determining the contribution of two-photon exchange to the elastic cross section. Two-photon exchange might resolve the discrepancy between measurements of the proton form factor ratio, $μ_p G^p_E/G^p_M$, made using polarization techniques and those made in unpolarized experiments. OLYMPUS operated on the DORIS storage ring at DESY, alternating between 2.01~GeV electron and positron beams incident on an internal hydrogen gas target. The experiment used a toroidal magnetic spectrometer instrumented with drift chambers and time-of-flight detectors to measure rates for elastic scattering over the polar angular range of approximately $25^\circ$--$75^\circ$. Symmetric Møller/Bhabha calorimeters at $1.29^\circ$ and telescopes of GEM and MWPC detectors at $12^\circ$ served as luminosity monitors. A total luminosity of approximately 4.5~fb$^{-1}$ was collected over two running periods in 2012. This paper provides details on the accelerator, target, detectors, and operation of the experiment.
△ Less
Submitted 5 December, 2013;
originally announced December 2013.
