-
Future Circular Collider Feasibility Study Report: Volume 2, Accelerators, Technical Infrastructure and Safety
Authors:
M. Benedikt,
F. Zimmermann,
B. Auchmann,
W. Bartmann,
J. P. Burnet,
C. Carli,
A. Chancé,
P. Craievich,
M. Giovannozzi,
C. Grojean,
J. Gutleber,
K. Hanke,
A. Henriques,
P. Janot,
C. Lourenço,
M. Mangano,
T. Otto,
J. Poole,
S. Rajagopalan,
T. Raubenheimer,
E. Todesco,
L. Ulrici,
T. Watson,
G. Wilkinson,
A. Abada
, et al. (1439 additional authors not shown)
Abstract:
In response to the 2020 Update of the European Strategy for Particle Physics, the Future Circular Collider (FCC) Feasibility Study was launched as an international collaboration hosted by CERN. This report describes the FCC integrated programme, which consists of two stages: an electron-positron collider (FCC-ee) in the first phase, serving as a high-luminosity Higgs, top, and electroweak factory;…
▽ More
In response to the 2020 Update of the European Strategy for Particle Physics, the Future Circular Collider (FCC) Feasibility Study was launched as an international collaboration hosted by CERN. This report describes the FCC integrated programme, which consists of two stages: an electron-positron collider (FCC-ee) in the first phase, serving as a high-luminosity Higgs, top, and electroweak factory; followed by a proton-proton collider (FCC-hh) at the energy frontier in the second phase.
FCC-ee is designed to operate at four key centre-of-mass energies: the Z pole, the WW production threshold, the ZH production peak, and the top/anti-top production threshold - delivering the highest possible luminosities to four experiments. Over 15 years of operation, FCC-ee will produce more than 6 trillion Z bosons, 200 million WW pairs, nearly 3 million Higgs bosons, and 2 million top anti-top pairs. Precise energy calibration at the Z pole and WW threshold will be achieved through frequent resonant depolarisation of pilot bunches. The sequence of operation modes remains flexible.
FCC-hh will operate at a centre-of-mass energy of approximately 85 TeV - nearly an order of magnitude higher than the LHC - and is designed to deliver 5 to 10 times the integrated luminosity of the HL-LHC. Its mass reach for direct discovery extends to several tens of TeV. In addition to proton-proton collisions, FCC-hh is capable of supporting ion-ion, ion-proton, and lepton-hadron collision modes.
This second volume of the Feasibility Study Report presents the complete design of the FCC-ee collider, its operation and staging strategy, the full-energy booster and injector complex, required accelerator technologies, safety concepts, and technical infrastructure. It also includes the design of the FCC-hh hadron collider, development of high-field magnets, hadron injector options, and key technical systems for FCC-hh.
△ Less
Submitted 25 April, 2025;
originally announced May 2025.
-
Future Circular Collider Feasibility Study Report: Volume 3, Civil Engineering, Implementation and Sustainability
Authors:
M. Benedikt,
F. Zimmermann,
B. Auchmann,
W. Bartmann,
J. P. Burnet,
C. Carli,
A. Chancé,
P. Craievich,
M. Giovannozzi,
C. Grojean,
J. Gutleber,
K. Hanke,
A. Henriques,
P. Janot,
C. Lourenço,
M. Mangano,
T. Otto,
J. Poole,
S. Rajagopalan,
T. Raubenheimer,
E. Todesco,
L. Ulrici,
T. Watson,
G. Wilkinson,
P. Azzi
, et al. (1439 additional authors not shown)
Abstract:
Volume 3 of the FCC Feasibility Report presents studies related to civil engineering, the development of a project implementation scenario, and environmental and sustainability aspects. The report details the iterative improvements made to the civil engineering concepts since 2018, taking into account subsurface conditions, accelerator and experiment requirements, and territorial considerations. I…
▽ More
Volume 3 of the FCC Feasibility Report presents studies related to civil engineering, the development of a project implementation scenario, and environmental and sustainability aspects. The report details the iterative improvements made to the civil engineering concepts since 2018, taking into account subsurface conditions, accelerator and experiment requirements, and territorial considerations. It outlines a technically feasible and economically viable civil engineering configuration that serves as the baseline for detailed subsurface investigations, construction design, cost estimation, and project implementation planning. Additionally, the report highlights ongoing subsurface investigations in key areas to support the development of an improved 3D subsurface model of the region.
The report describes development of the project scenario based on the 'avoid-reduce-compensate' iterative optimisation approach. The reference scenario balances optimal physics performance with territorial compatibility, implementation risks, and costs. Environmental field investigations covering almost 600 hectares of terrain - including numerous urban, economic, social, and technical aspects - confirmed the project's technical feasibility and contributed to the preparation of essential input documents for the formal project authorisation phase. The summary also highlights the initiation of public dialogue as part of the authorisation process. The results of a comprehensive socio-economic impact assessment, which included significant environmental effects, are presented. Even under the most conservative and stringent conditions, a positive benefit-cost ratio for the FCC-ee is obtained. Finally, the report provides a concise summary of the studies conducted to document the current state of the environment.
△ Less
Submitted 25 April, 2025;
originally announced May 2025.
-
Future Circular Collider Feasibility Study Report: Volume 1, Physics, Experiments, Detectors
Authors:
M. Benedikt,
F. Zimmermann,
B. Auchmann,
W. Bartmann,
J. P. Burnet,
C. Carli,
A. Chancé,
P. Craievich,
M. Giovannozzi,
C. Grojean,
J. Gutleber,
K. Hanke,
A. Henriques,
P. Janot,
C. Lourenço,
M. Mangano,
T. Otto,
J. Poole,
S. Rajagopalan,
T. Raubenheimer,
E. Todesco,
L. Ulrici,
T. Watson,
G. Wilkinson,
P. Azzi
, et al. (1439 additional authors not shown)
Abstract:
Volume 1 of the FCC Feasibility Report presents an overview of the physics case, experimental programme, and detector concepts for the Future Circular Collider (FCC). This volume outlines how FCC would address some of the most profound open questions in particle physics, from precision studies of the Higgs and EW bosons and of the top quark, to the exploration of physics beyond the Standard Model.…
▽ More
Volume 1 of the FCC Feasibility Report presents an overview of the physics case, experimental programme, and detector concepts for the Future Circular Collider (FCC). This volume outlines how FCC would address some of the most profound open questions in particle physics, from precision studies of the Higgs and EW bosons and of the top quark, to the exploration of physics beyond the Standard Model. The report reviews the experimental opportunities offered by the staged implementation of FCC, beginning with an electron-positron collider (FCC-ee), operating at several centre-of-mass energies, followed by a hadron collider (FCC-hh). Benchmark examples are given of the expected physics performance, in terms of precision and sensitivity to new phenomena, of each collider stage. Detector requirements and conceptual designs for FCC-ee experiments are discussed, as are the specific demands that the physics programme imposes on the accelerator in the domains of the calibration of the collision energy, and the interface region between the accelerator and the detector. The report also highlights advances in detector, software and computing technologies, as well as the theoretical tools /reconstruction techniques that will enable the precision measurements and discovery potential of the FCC experimental programme. This volume reflects the outcome of a global collaborative effort involving hundreds of scientists and institutions, aided by a dedicated community-building coordination, and provides a targeted assessment of the scientific opportunities and experimental foundations of the FCC programme.
△ Less
Submitted 25 April, 2025;
originally announced May 2025.
-
The Muon Collider
Authors:
Carlotta Accettura,
Simon Adrian,
Rohit Agarwal,
Claudia Ahdida,
Chiara Aime',
Avni Aksoy,
Gian Luigi Alberghi,
Siobhan Alden,
Luca Alfonso,
Muhammad Ali,
Anna Rita Altamura,
Nicola Amapane,
Kathleen Amm,
David Amorim,
Paolo Andreetto,
Fabio Anulli,
Ludovica Aperio Bella,
Rob Appleby,
Artur Apresyan,
Pouya Asadi,
Mohammed Attia Mahmoud,
Bernhard Auchmann,
John Back,
Anthony Badea,
Kyu Jung Bae
, et al. (433 additional authors not shown)
Abstract:
Muons offer a unique opportunity to build a compact high-energy electroweak collider at the 10 TeV scale. A Muon Collider enables direct access to the underlying simplicity of the Standard Model and unparalleled reach beyond it. It will be a paradigm-shifting tool for particle physics representing the first collider to combine the high-energy reach of a proton collider and the high precision of an…
▽ More
Muons offer a unique opportunity to build a compact high-energy electroweak collider at the 10 TeV scale. A Muon Collider enables direct access to the underlying simplicity of the Standard Model and unparalleled reach beyond it. It will be a paradigm-shifting tool for particle physics representing the first collider to combine the high-energy reach of a proton collider and the high precision of an electron-positron collider, yielding a physics potential significantly greater than the sum of its individual parts. A high-energy muon collider is the natural next step in the exploration of fundamental physics after the HL-LHC and a natural complement to a future low-energy Higgs factory. Such a facility would significantly broaden the scope of particle colliders, engaging the many frontiers of the high energy community.
The last European Strategy for Particle Physics Update and later the Particle Physics Project Prioritisation Panel in the US requested a study of the muon collider, which is being carried on by the International Muon Collider Collaboration. In this comprehensive document we present the physics case, the state of the work on accelerator design and technology, and propose an R\&D project that can make the muon collider a reality.
△ Less
Submitted 30 April, 2025;
originally announced April 2025.
-
High Field Magnet Programme -- European Strategy Input
Authors:
B. Auchmann,
E. Todesco,
A. Ballarino,
N. Bagrets,
A. Milanese,
E. Rochepault,
L. Rossi,
C. Senatore,
F. Toral
Abstract:
In this submission, we describe research goals, implementation, and timelines of the High Field Magnet Programme, hosted by CERN. The programme pursues accelerator-magnet R&D with low-temperature- and high-temperature superconductor technology with a main focus on the FCC-hh. Following a long tradition of magnet R&D for high-energy particle colliders, HFM R&D fosters important societal impact thro…
▽ More
In this submission, we describe research goals, implementation, and timelines of the High Field Magnet Programme, hosted by CERN. The programme pursues accelerator-magnet R&D with low-temperature- and high-temperature superconductor technology with a main focus on the FCC-hh. Following a long tradition of magnet R&D for high-energy particle colliders, HFM R&D fosters important societal impact through synergies with other fields.
△ Less
Submitted 23 April, 2025;
originally announced April 2025.
-
Magnet R&D for the Muon Collider -- European Strategy Input
Authors:
L. Bottura,
B. Auchmann,
F. Boattini,
B. Bordini,
B. Caiffi,
L. Cooley,
S. Fabbri,
S. Gourlay,
S. Mariotto,
T. Nakamoto,
S. Prestemon,
M. Statera
Abstract:
The Muon Collider, proposed under the International Muon Collider Collaboration (IMCC), represents a groundbreaking advancement in circular collider technology. By using muons instead of protons or electrons, this collider has the potential of unprecedented discovery reach, luminosity, and compact design, significantly increasing energy efficiency, reducing environmental impact and improving susta…
▽ More
The Muon Collider, proposed under the International Muon Collider Collaboration (IMCC), represents a groundbreaking advancement in circular collider technology. By using muons instead of protons or electrons, this collider has the potential of unprecedented discovery reach, luminosity, and compact design, significantly increasing energy efficiency, reducing environmental impact and improving sustainability. However, achieving this vision necessitates overcoming unique and extreme challenges in superconducting magnet technology. This document summarizes the state of the art, challenges, and the proposed R&D roadmap for developing the next generation of superconducting magnet systems crucial for the Muon Collider over the next ten years. The goal is to advance accelerator magnet technology beyond current limits, with a special focus on High-Temperature Superconductors (HTS) materials for high-field and high-temperature applications. This note is a concise summary of the extensive proposal [BOT-2025] which we refer to for detailed referencing and as supporting material. We focus here on the technology gap to be filled by the proposed R&D, the structure and objectives of the proposed R&D, and provide the resource estimate for the next ten years.
△ Less
Submitted 1 April, 2025; v1 submitted 27 March, 2025;
originally announced March 2025.
-
Magnet R&D for the Muon Collider
Authors:
L. Bottura,
B. Auchmann,
F. Boattini,
B. Bordini,
B. Caiffi,
L. Cooley,
S. Fabbri,
S. Gourlay,
S. Mariotto,
T. Nakamoto,
S. Prestemon,
M. Statera
Abstract:
A proton-driven Muon Collider, in the configuration that has resulted from the efforts of the International Muon Collider Collaboration (IMCC), poses multiple and exceptional magnet system challenges. Addressing these challenges will require a focused effort to advance accelerator magnet technology well beyond the present state of the art, including activities that have not previously been support…
▽ More
A proton-driven Muon Collider, in the configuration that has resulted from the efforts of the International Muon Collider Collaboration (IMCC), poses multiple and exceptional magnet system challenges. Addressing these challenges will require a focused effort to advance accelerator magnet technology well beyond the present state of the art, including activities that have not previously been supported by High Energy Physics (HEP) programs, but are synergic with them. This proposal presents the motivation for a directed effort focusing on the development and testing of small- and full-scale magnet prototypes, ultimately culminating in their validation under collider-relevant conditions. This document summarizes technology status, challenges, and development targets, and outlines a detailed plan with staged milestones to advance the technological readiness of magnet systems, bringing the realization of the Muon Collider closer to reality. The total resources to achieve this goal are estimated at 82.5 MCHF and 414 FTE y over ten years, of which 39 MCHF and 199 FTE y are engaged over the first five years. Reaching the desired performance with sustainable technology will depend greatly on exploiting the potential of High Temperature Superconductors (HTS). Mainly because of this, the R&D proposed here has significant potential to broadly impact HEP and its other circular collider considerations such as the FCC-hh, as well as other fields of scientific and societal application, e.g. science in high magnetic fields, NMR and MRI, fusion and other power and mobility applications.
△ Less
Submitted 31 March, 2025; v1 submitted 27 March, 2025;
originally announced March 2025.
-
MuCol Milestone Report No. 5: Preliminary Parameters
Authors:
Carlotta Accettura,
Simon Adrian,
Rohit Agarwal,
Claudia Ahdida,
Chiara Aimé,
Avni Aksoy,
Gian Luigi Alberghi,
Siobhan Alden,
Luca Alfonso,
Nicola Amapane,
David Amorim,
Paolo Andreetto,
Fabio Anulli,
Rob Appleby,
Artur Apresyan,
Pouya Asadi,
Mohammed Attia Mahmoud,
Bernhard Auchmann,
John Back,
Anthony Badea,
Kyu Jung Bae,
E. J. Bahng,
Lorenzo Balconi,
Fabrice Balli,
Laura Bandiera
, et al. (369 additional authors not shown)
Abstract:
This document is comprised of a collection of updated preliminary parameters for the key parts of the muon collider. The updated preliminary parameters follow on from the October 2023 Tentative Parameters Report. Particular attention has been given to regions of the facility that are believed to hold greater technical uncertainty in their design and that have a strong impact on the cost and power…
▽ More
This document is comprised of a collection of updated preliminary parameters for the key parts of the muon collider. The updated preliminary parameters follow on from the October 2023 Tentative Parameters Report. Particular attention has been given to regions of the facility that are believed to hold greater technical uncertainty in their design and that have a strong impact on the cost and power consumption of the facility. The data is collected from a collaborative spreadsheet and transferred to overleaf.
△ Less
Submitted 5 November, 2024;
originally announced November 2024.
-
Interim report for the International Muon Collider Collaboration (IMCC)
Authors:
C. Accettura,
S. Adrian,
R. Agarwal,
C. Ahdida,
C. Aimé,
A. Aksoy,
G. L. Alberghi,
S. Alden,
N. Amapane,
D. Amorim,
P. Andreetto,
F. Anulli,
R. Appleby,
A. Apresyan,
P. Asadi,
M. Attia Mahmoud,
B. Auchmann,
J. Back,
A. Badea,
K. J. Bae,
E. J. Bahng,
L. Balconi,
F. Balli,
L. Bandiera,
C. Barbagallo
, et al. (362 additional authors not shown)
Abstract:
The International Muon Collider Collaboration (IMCC) [1] was established in 2020 following the recommendations of the European Strategy for Particle Physics (ESPP) and the implementation of the European Strategy for Particle Physics-Accelerator R&D Roadmap by the Laboratory Directors Group [2], hereinafter referred to as the the European LDG roadmap. The Muon Collider Study (MuC) covers the accele…
▽ More
The International Muon Collider Collaboration (IMCC) [1] was established in 2020 following the recommendations of the European Strategy for Particle Physics (ESPP) and the implementation of the European Strategy for Particle Physics-Accelerator R&D Roadmap by the Laboratory Directors Group [2], hereinafter referred to as the the European LDG roadmap. The Muon Collider Study (MuC) covers the accelerator complex, detectors and physics for a future muon collider. In 2023, European Commission support was obtained for a design study of a muon collider (MuCol) [3]. This project started on 1st March 2023, with work-packages aligned with the overall muon collider studies. In preparation of and during the 2021-22 U.S. Snowmass process, the muon collider project parameters, technical studies and physics performance studies were performed and presented in great detail. Recently, the P5 panel [4] in the U.S. recommended a muon collider R&D, proposed to join the IMCC and envisages that the U.S. should prepare to host a muon collider, calling this their "muon shot". In the past, the U.S. Muon Accelerator Programme (MAP) [5] has been instrumental in studies of concepts and technologies for a muon collider.
△ Less
Submitted 28 January, 2025; v1 submitted 17 July, 2024;
originally announced July 2024.
-
The P$^3$ Experiment: A Positron Source Demonstrator for Future Lepton Colliders
Authors:
Nicolas Vallis,
Paolo Craievich,
Mattia Schär,
Riccardo Zennaro,
Bernard Auchmann,
Hans-Heinrich Braun,
Maria Ilaria Besana,
Michal Duda,
Reto Fortunati,
Henrique Garcia Rodrigues,
Dominique Hauenstein,
Rasmus Ischebeck Rasmus,
Pavle Juranić,
Jaap Kosse,
Fabio Marcellini,
Thomas Uli Michlmayr,
Stefan Müller,
Marco Pedrozzi,
Renzo Rotundo,
Gian Luca Orlandi,
Mike Seidel,
Nick Parsifal Strohmaier,
Mariia Zykova
Abstract:
The PSI Positron Production (P$^3$ or P-cubed) experiment is a demonstrator for a e+ source and capture system with potential to improve the state-of-the-art e+ yield by an order of magnitude. The experiment is driven by the FCC-ee injector study and will be hosted in the SwissFEL facility at the Paul Scherrer Institute in Switzerland. This paper is an overview of the P$^3$ design at an advanced s…
▽ More
The PSI Positron Production (P$^3$ or P-cubed) experiment is a demonstrator for a e+ source and capture system with potential to improve the state-of-the-art e+ yield by an order of magnitude. The experiment is driven by the FCC-ee injector study and will be hosted in the SwissFEL facility at the Paul Scherrer Institute in Switzerland. This paper is an overview of the P$^3$ design at an advanced stage, with a particular emphasis on a novel e+ capture system and its associated beam dynamics. Additionally, a concept for the experiment diagnostics is presented, as well as the key points of the ongoing installation works.
△ Less
Submitted 1 September, 2023; v1 submitted 31 August, 2023;
originally announced August 2023.
-
Training performance of Nb3Sn Rutherford cables in a channel with a wide range of impregnation materials
Authors:
S. Otten,
A. Kario,
W. A. J. Wessel. J. Leferink,
H. H. J. ten Kate,
M. Daly,
C. Hug,
S. Sidorov,
A. Brem,
B. Auchmann,
P. Studer,
T. Tervoort
Abstract:
Training of accelerator magnets is a costly and time consuming process. The number of training quenches must therefore be reduced to a minimum. We investigate training of impregnated Nb3Sn Rutherford cable in a small-scale experiment. The test involves a Rutherford cable impregnated in a meandering channel simulating the environment of a canted-cosine-theta (CCT) coil. The sample is powered using…
▽ More
Training of accelerator magnets is a costly and time consuming process. The number of training quenches must therefore be reduced to a minimum. We investigate training of impregnated Nb3Sn Rutherford cable in a small-scale experiment. The test involves a Rutherford cable impregnated in a meandering channel simulating the environment of a canted-cosine-theta (CCT) coil. The sample is powered using a transformer and the Lorentz force is generated by an externally applied magnetic field. The low material and helium consumption enable the test of a larger number of samples. In this article, we present training of samples impregnated with alumina-filled epoxy resins, a modified resin with paraffin-like mechanical properties, and a new tough resin in development at ETH Zürich. These new data are compared with previous results published earlier. Compared to samples with unfilled epoxy resin, those with alumina-filled epoxy show favorable training properties with higher initial quench currents and fewer training quenches before reaching 80% of the critical current.
△ Less
Submitted 18 November, 2022;
originally announced November 2022.
-
A Work Proposal for a Collaborative Study of Magnet Technology for a Future Muon Collider
Authors:
L. Bottura,
D. Aguglia,
B. Auchmann,
T. Arndt,
J. Beard,
A. Bersani,
F. Boattini,
M. Breschi,
B. Caiffi,
X. Chaud,
M. Dam,
F. Debray,
H. De Gersem,
E. De Matteis,
A. Dudarev,
S. Farinon,
A. Kario,
R. Losito,
S. Mariotto,
M. Mentink,
R. Musenich,
T. Ogitsu,
M. Prioli,
L. Quettier,
L. Rossi
, et al. (8 additional authors not shown)
Abstract:
In this paper we elaborate on the nature and challenges for the magnet systems of a muon collider as presently considered within the scope of the International Muon Collider Collaboration (IMCC). We outline the structure of the work proposed over the coming period of five years to study and demonstrate relevant magnet technology. The proposal, which is part of the overall work planned to establish…
▽ More
In this paper we elaborate on the nature and challenges for the magnet systems of a muon collider as presently considered within the scope of the International Muon Collider Collaboration (IMCC). We outline the structure of the work proposed over the coming period of five years to study and demonstrate relevant magnet technology. The proposal, which is part of the overall work planned to establish feasibility of a muon collider, is in direct response to the recent recommendations received from the Laboratories Directors Group (LDG). The plan is to profit from joint activities, within the scope of the IMCC and beyond, implemented through direct and EU-funded contributions.
△ Less
Submitted 29 March, 2022; v1 submitted 26 March, 2022;
originally announced March 2022.
-
A Strategic Approach to Advance Magnet Technology for Next Generation Colliders
Authors:
G. Ambrosio,
K. Amm,
M. Anerella,
G. Apollinari,
D. Arbelaez,
B. Auchmann,
S. Balachandran,
M. Baldini,
A. Ballarino,
S. Barua,
E. Barzi,
A. Baskys,
C. Bird,
J. Boerme,
E. Bosque,
L. Brouwer,
S. Caspi,
N. Cheggour,
G. Chlachidze,
L. Cooley,
D. Davis,
D. Dietderich,
J. DiMarco,
L. English,
L. Garcia Fajardo
, et al. (52 additional authors not shown)
Abstract:
Colliders are built on a foundation of superconducting magnet technology that provides strong dipole magnets to maintain the beam orbit and strong focusing magnets to enable the extraordinary luminosity required to probe physics at the energy frontier. The dipole magnet strength plays a critical role in dictating the energy reach of a collider, and the superconducting magnets are arguably the domi…
▽ More
Colliders are built on a foundation of superconducting magnet technology that provides strong dipole magnets to maintain the beam orbit and strong focusing magnets to enable the extraordinary luminosity required to probe physics at the energy frontier. The dipole magnet strength plays a critical role in dictating the energy reach of a collider, and the superconducting magnets are arguably the dominant cost driver for future collider facilities. As the community considers opportunities to explore new energy frontiers, the importance of advanced magnet technology - both in terms of magnet performance and in the magnet technology's potential for cost reduction - is evident, as the technology status is essential for informed decisions on targets for physics reach and facility feasibility.
△ Less
Submitted 26 March, 2022;
originally announced March 2022.
-
High Field Magnet Development for HEP in Europe: A Proposal from LDG HFM Expert Panel
Authors:
Pierre Védrine,
Luis Garcia-Tabarès,
Bernhard Auchmann,
Amalia Ballarino,
Bertrand Baudouy,
Luca Bottura,
Philippe Fazilleau,
Mathias Noe,
Soren Prestemon,
Etienne Rochepault,
Lucio Rossi,
Carmine Senatore,
Ben Shepherd
Abstract:
The European Laboratory Directors Group (LDG) was mandated by CERN Council in 2021 to oversee the development of an Accelerator R&D Roadmap. To this end, a set of expert panels was convened, covering the five broad areas of accelerator R&D highlighted in the ESPPU. The High Field Magnet (HFM) Panel is proposing a programme to demonstrate Nb3Sn magnet technology for large-scale deployment and to in…
▽ More
The European Laboratory Directors Group (LDG) was mandated by CERN Council in 2021 to oversee the development of an Accelerator R&D Roadmap. To this end, a set of expert panels was convened, covering the five broad areas of accelerator R&D highlighted in the ESPPU. The High Field Magnet (HFM) Panel is proposing a programme to demonstrate Nb3Sn magnet technology for large-scale deployment and to investigate the suitability of high temperature superconductors (HTS) for accelerator magnet applications. A summary of this programme is presented here.
△ Less
Submitted 15 March, 2022;
originally announced March 2022.
-
Millisecond Time-Scale Measurements of Heat Transfer to Confined He II
Authors:
Jonas Blomberg Ghini,
Bernhard Auchmann,
Bertrand Baudouy
Abstract:
We explore transient heat transfer, on the millisecond time-scale, from a narrow, rectangular stainless steel heater cooled from one side by He II confined to a channel of 120 $μ$m depth. The helium is isolated from the external bath with the exception of two pin-holes of cross section about 10% that of the channel.
We measure the temperatures of both the heater strip and the channel helium duri…
▽ More
We explore transient heat transfer, on the millisecond time-scale, from a narrow, rectangular stainless steel heater cooled from one side by He II confined to a channel of 120 $μ$m depth. The helium is isolated from the external bath with the exception of two pin-holes of cross section about 10% that of the channel.
We measure the temperatures of both the heater strip and the channel helium during slow-pulse heating that reaches peak power after 9 ms, fast-pulse heating that reaches peak power after 100 $μ$s, and step heating that reaches steady power after 100 $μ$s.
Using the steady state Kapitza heat transfer expression at the interface between heater and helium, and the Gorter-Mellink heat transfer regime in the helium channel, we obtain excellent agreement between simulation and measurement during the first 5 ms of slow-pulse tests. Using instead the measured helium temperature in the Kapitza expression, we obtain excellent agreement between the simulated and measured heater response during the first 150 ms of slow-pulse tests.
The same model fails to explain the fast-pulse transient response of the heater and helium, while it can explain the helium response to a step in applied power but not the heater response. The steady state Kapitza expression may therefore not be applicable to heating events that are over within a single millisecond.
△ Less
Submitted 9 March, 2022;
originally announced March 2022.
-
Millisecond Time-Scale Measurements of Heat Transfer to an Open Bath of He II
Authors:
Jonas Blomberg Ghini,
Bernhard Auchmann,
Bertrand Baudouy
Abstract:
We explore steady state and transient heat transfer from a narrow, rectangular stainless steel heater strip cooled from one side by an open bath of He~II. Setup validation is done by fitting the Kapitza heat transfer expression $Q = a_\mathrm{K} \left( {T_\mathrm{s}}^{n_\mathrm{K}} - {T_\mathrm{b}}^{n_\mathrm{K}} \right)$ to steady state measurements, finding fit parameters within the expected ran…
▽ More
We explore steady state and transient heat transfer from a narrow, rectangular stainless steel heater strip cooled from one side by an open bath of He~II. Setup validation is done by fitting the Kapitza heat transfer expression $Q = a_\mathrm{K} \left( {T_\mathrm{s}}^{n_\mathrm{K}} - {T_\mathrm{b}}^{n_\mathrm{K}} \right)$ to steady state measurements, finding fit parameters within the expected range; $a_\mathrm{K}$ = 1316.8$\pm10\%$ $\mathrm{W}\mathrm{m}^{-2}\mathrm{K}^{-1}$, $n_\mathrm{K}$ = 2.528$\pm10\%$. We find critical heat flux in line with estimates from literature, and the time between a step in heating and the onset of film boiling follows the expected $\propto Q^{-4}$ dependence. During the first millisecond after a step in applied heating power density our measurements show a slower thermal rise time than that found by a time-dependent one-dimensional model of our setup using the steady state Kapitza heat transfer expression as the cooling boundary condition. However, the results compare favourably with transient measurements in literature. After the first millisecond, agreement between measurement and model is excellent. We do not find conclusive evidence of an orientation dependence of the Kapitza heat transfer mechanism, nor heat transfer differences that can be attributed to local surface variations along the same heater.
△ Less
Submitted 9 March, 2022;
originally announced March 2022.
-
Improved training in paraffin-wax impregnated Nb3Sn Rutherford cables demonstrated in BOX samples
Authors:
Michael Daly,
Bernard Auchmann,
André Brem,
Christoph Hug,
Serguei Sidorov,
Simon Otten,
Marc Dhallé,
Zichuan Guo,
Anna Kario,
Herman ten Kate
Abstract:
Resin-impregnated high-field Nb3Sn type of accelerator magnets are known to require extensive training campaigns and even may exhibit performance-limiting defects after thermal or electromagnetic cycling. In order to efficiently explore technological solutions for this behaviour and assess a wide variety of impregnation material combinations and surface treatments, the BOnding eXperiment (BOX) sam…
▽ More
Resin-impregnated high-field Nb3Sn type of accelerator magnets are known to require extensive training campaigns and even may exhibit performance-limiting defects after thermal or electromagnetic cycling. In order to efficiently explore technological solutions for this behaviour and assess a wide variety of impregnation material combinations and surface treatments, the BOnding eXperiment (BOX) sample was developed. BOX provides a short-sample test platform featuring magnet-relevant Lorentz forces and exhibits associated training. Here we report on the comparative behaviour of BOX samples comprising the same Nb3Sn Rutherford cable but impregnated either with common resins used in high-field magnets, or with less conventional paraffin wax. Remarkably, the two paraffin wax-impregnated BOX samples reached their critical current without training and are also resilient to thermal and mechanical cycling. These rather encouraging results strongly contrast to those obtained with resin impregnated samples, which show the characteristic extensive training and at best barely reach their critical current value.
△ Less
Submitted 26 January, 2022;
originally announced January 2022.
-
European Strategy for Particle Physics -- Accelerator R&D Roadmap
Authors:
C. Adolphsen,
D. Angal-Kalinin,
T. Arndt,
M. Arnold,
R. Assmann,
B. Auchmann,
K. Aulenbacher,
A. Ballarino,
B. Baudouy,
P. Baudrenghien,
M. Benedikt,
S. Bentvelsen,
A. Blondel,
A. Bogacz,
F. Bossi,
L. Bottura,
S. Bousson,
O. Brüning,
R. Brinkmann,
M. Bruker,
O. Brunner,
P. N. Burrows,
G. Burt,
S. Calatroni,
K. Cassou
, et al. (111 additional authors not shown)
Abstract:
The 2020 update of the European Strategy for Particle Physics emphasised the importance of an intensified and well-coordinated programme of accelerator R&D, supporting the design and delivery of future particle accelerators in a timely, affordable and sustainable way. This report sets out a roadmap for European accelerator R&D for the next five to ten years, covering five topical areas identified…
▽ More
The 2020 update of the European Strategy for Particle Physics emphasised the importance of an intensified and well-coordinated programme of accelerator R&D, supporting the design and delivery of future particle accelerators in a timely, affordable and sustainable way. This report sets out a roadmap for European accelerator R&D for the next five to ten years, covering five topical areas identified in the Strategy update. The R&D objectives include: improvement of the performance and cost-performance of magnet and radio-frequency acceleration systems; investigations of the potential of laser / plasma acceleration and energy-recovery linac techniques; and development of new concepts for muon beams and muon colliders. The goal of the roadmap is to document the collective view of the field on the next steps for the R&D programme, and to provide the evidence base to support subsequent decisions on prioritisation, resourcing and implementation.
△ Less
Submitted 30 March, 2022; v1 submitted 19 January, 2022;
originally announced January 2022.
-
A Coupled A-H Formulation for Magneto-Thermal Transients in High-Temperature Superconducting Magnets
Authors:
Lorenzo Bortot,
Bernhard Auchmann,
Idoia Cortes Garcia,
Herbert De Gersem,
Michał Maciejewski,
Matthias Mentink,
Sebastian Schöps,
Jeroen Van Nugteren,
Arjan Verweij
Abstract:
The application of high-temperature superconductors to accelerator magnets for future particle colliders is under study. Numerical methods are crucial for an accurate evaluation of the complex dynamical behavior of the magnets, especially concerning the magnetic field quality and thermal behavior. We present a coupled $\textbf{A}$-$\textbf{H}$ field formulation for the analysis of magneto-thermal…
▽ More
The application of high-temperature superconductors to accelerator magnets for future particle colliders is under study. Numerical methods are crucial for an accurate evaluation of the complex dynamical behavior of the magnets, especially concerning the magnetic field quality and thermal behavior. We present a coupled $\textbf{A}$-$\textbf{H}$ field formulation for the analysis of magneto-thermal transients in accelerator magnets. The magnetic field strength $\textbf{H}$ accounts for the eddy current problem in the source regions containing the superconducting domains, while the magnetic vector potential $\textbf{A}$ represents the magnetoquasistatic problem in the normal and non-conducting domains. Furthermore, we include a slab approximation for the source regions, making the formulation suitable for large scale models composed of thousands of tapes. In this work, the relevant equations are derived and discussed, with emphasis on the coupling conditions. The weak formulation is derived, and numerical results are provided in order to both, verify the formulation and scale it to the size of an accelerator magnet.
△ Less
Submitted 17 January, 2020; v1 submitted 7 September, 2019;
originally announced September 2019.
-
STEAM: A Hierarchical Co-Simulation Framework for Superconducting Accelerator Magnet Circuits
Authors:
Lorenzo Bortot,
Bernhard Auchmann,
Idoia Cortes Garcia,
Alejando M. Fernando Navarro,
Michał Maciejewski,
Matthias Mentink,
Marco Prioli,
Emmanuele Ravaioli,
Sebastian Schöps,
Arjan Verweij
Abstract:
Simulating the transient effects occurring in superconducting accelerator magnet circuits requires including the mutual electro-thermo-dynamic interaction among the circuit elements, such as power converters, magnets, and protection systems. Nevertheless, the numerical analysis is traditionally done separately for each element in the circuit, leading to possible non-consistent results. We present…
▽ More
Simulating the transient effects occurring in superconducting accelerator magnet circuits requires including the mutual electro-thermo-dynamic interaction among the circuit elements, such as power converters, magnets, and protection systems. Nevertheless, the numerical analysis is traditionally done separately for each element in the circuit, leading to possible non-consistent results. We present STEAM, a hierarchical co-simulation framework featuring the waveform relaxation method. The framework simulates a complex system as a composition of simpler, independent models that exchange information. The convergence of the coupling algorithm ensures the consistency of the solution. The modularity of the framework allows integrating models developed with both proprietary and in-house tools. The framework implements a user-customizable hierarchical algorithm to schedule how models participate to the co-simulation, for the purpose of using computational resources efficiently. As a case study, a quench scenario is co-simulated for the inner triplet circuit for the High Luminosity upgrade of the LHC at CERN.
△ Less
Submitted 26 January, 2018;
originally announced January 2018.
-
Coupling of Magneto-Thermal and Mechanical Superconducting Magnet Models by Means of Mesh-Based Interpolation
Authors:
Michał Maciejewski,
Pascal Bayrasy,
Klaus Wolf,
Michał Wilczek,
Bernhard Auchmann,
Tina Griesemer,
Lorenzo Bortot,
Marco Prioli,
Alejandro Manuel Fernandez Navarro,
Sebastian Schöps,
Idoia Cortes Garcia,
Arjan Verweij
Abstract:
In this paper we present an algorithm for the coupling of magneto-thermal and mechanical finite element models representing superconducting accelerator magnets. The mechanical models are used during the design of the mechanical structure as well as the optimization of the magnetic field quality under nominal conditions. The magneto-thermal models allow for the analysis of transient phenomena occur…
▽ More
In this paper we present an algorithm for the coupling of magneto-thermal and mechanical finite element models representing superconducting accelerator magnets. The mechanical models are used during the design of the mechanical structure as well as the optimization of the magnetic field quality under nominal conditions. The magneto-thermal models allow for the analysis of transient phenomena occurring during quench initiation, propagation, and protection. Mechanical analysis of quenching magnets is of high importance considering the design of new protection systems and the study of new superconductor types. We use field/circuit coupling to determine temperature and electromagnetic force evolution during the magnet discharge. These quantities are provided as a load to existing mechanical models. The models are discretized with different meshes and, therefore, we employ a mesh-based interpolation method to exchange coupled quantities. The coupling algorithm is illustrated with a simulation of a mechanical response of a standalone high-field dipole magnet protected with CLIQ (Coupling-Loss Induced Quench) technology.
△ Less
Submitted 29 December, 2017;
originally announced December 2017.
-
Reduced Order Modelling for the Simulation of Quenches in Superconducting Magnets
Authors:
Sebastian Schöps,
Idoia Cortes Garcia,
Michał Maciejewski,
Bernhard Auchmann
Abstract:
This contributions discusses the simulation of magnetothermal effects in superconducting magnets as used in particle accelerators. An iterative coupling scheme using reduced order models between a magnetothermal partial differential model and an electrical lumped-element circuit is demonstrated. The multiphysics, multirate and multiscale problem requires a consistent formulation and framework to t…
▽ More
This contributions discusses the simulation of magnetothermal effects in superconducting magnets as used in particle accelerators. An iterative coupling scheme using reduced order models between a magnetothermal partial differential model and an electrical lumped-element circuit is demonstrated. The multiphysics, multirate and multiscale problem requires a consistent formulation and framework to tackle the challenging transient effects occurring at both system and device level.
△ Less
Submitted 13 October, 2017;
originally announced October 2017.
-
A 2-D Finite-Element Model for Electro-Thermal Transients in Accelerator Magnets
Authors:
Lorenzo Bortot,
Bernhard Auchmann,
Idoia Cortes Garcia,
Alejandro Manuel Fernandez Navarro,
Michal Maciejewski,
Marco Prioli,
Sebastian Schöps,
Arjan Verweij
Abstract:
Superconducting accelerator magnets require sophisticated monitoring and means of protection due to the large energy stored in the magnetic field. Numerical simulations play a crucial role in understanding transient phenomena occurring within the magnet, and can, therefore, help to prevent disruptive consequences. We present a 2-D FEM model for the simulation of electro-thermal transients occurrin…
▽ More
Superconducting accelerator magnets require sophisticated monitoring and means of protection due to the large energy stored in the magnetic field. Numerical simulations play a crucial role in understanding transient phenomena occurring within the magnet, and can, therefore, help to prevent disruptive consequences. We present a 2-D FEM model for the simulation of electro-thermal transients occurring in superconducting accelerator magnets. The magnetoquasistatic problem is solved with a modified magnetic vector potential formulation, where the cable eddy currents are resolved in terms of their equivalent magnetization. The heat balance equation is then investigated, and the relevant heat sources are discussed. The model implements a two-port component interface and is resolved, as part of an electrical circuit, in a cooperative simulation scheme with a lumped-parameter network.
△ Less
Submitted 5 December, 2017; v1 submitted 3 October, 2017;
originally announced October 2017.
-
PERLE: Powerful Energy Recovery Linac for Experiments - Conceptual Design Report
Authors:
D. Angal-Kalinin,
G. Arduini,
B. Auchmann,
J. Bernauer,
A. Bogacz,
F. Bordry,
S. Bousson,
C. Bracco,
O. Brüning,
R. Calaga,
K. Cassou,
V. Chetvertkova,
E. Cormier,
E. Daly,
D. Douglas,
K. Dupraz,
B. Goddard,
J. Henry,
A. Hutton,
E. Jensen,
W. Kaabi,
M. Klein,
P. Kostka,
F. Marhauser,
A. Martens
, et al. (17 additional authors not shown)
Abstract:
A conceptual design is presented of a novel ERL facility for the development and application of the energy recovery technique to linear electron accelerators in the multi-turn, large current and large energy regime. The main characteristics of the powerful energy recovery linac experiment facility (PERLE) are derived from the design of the Large Hadron electron Collider, an electron beam upgrade u…
▽ More
A conceptual design is presented of a novel ERL facility for the development and application of the energy recovery technique to linear electron accelerators in the multi-turn, large current and large energy regime. The main characteristics of the powerful energy recovery linac experiment facility (PERLE) are derived from the design of the Large Hadron electron Collider, an electron beam upgrade under study for the LHC, for which it would be the key demonstrator. PERLE is thus projected as a facility to investigate efficient, high current (> 10 mA) ERL operation with three re-circulation passages through newly designed SCRF cavities, at 801.58 MHz frequency, and following deceleration over another three re-circulations. In its fully equipped configuration, PERLE provides an electron beam of approximately 1 GeV energy. A physics programme possibly associated with PERLE is sketched, consisting of high precision elastic electron-proton scattering experiments, as well as photo-nuclear reactions of unprecedented intensities with up to 30 MeV photon beam energy as may be obtained using Fabry-Perot cavities. The facility has further applications as a general technology test bed that can investigate and validate novel superconducting magnets (beam induced quench tests) and superconducting RF structures (structure tests with high current beams, beam loading and transients). Besides a chapter on operation aspects, the report contains detailed considerations on the choices for the SCRF structure, optics and lattice design, solutions for arc magnets, source and injector and on further essential components. A suitable configuration derived from the here presented design concept may next be moved forward to a technical design and possibly be built by an international collaboration which is being established.
△ Less
Submitted 24 May, 2017;
originally announced May 2017.
-
Application of the Waveform Relaxation Technique to the Co-Simulation of Power Converter Controller and Electrical Circuit Models
Authors:
Michał Maciejewski,
Idoia Cortes Garcia,
Sebastian Schöps,
Bernhard Auchmann,
Lorenzo Bortot,
Marco Prioli,
Arjan Verweij
Abstract:
In this paper we present the co-simulation of a PID class power converter controller and an electrical circuit by means of the waveform relaxation technique. The simulation of the controller model is characterized by a fixed-time stepping scheme reflecting its digital implementation, whereas a circuit simulation usually employs an adaptive time stepping scheme in order to account for a wide range…
▽ More
In this paper we present the co-simulation of a PID class power converter controller and an electrical circuit by means of the waveform relaxation technique. The simulation of the controller model is characterized by a fixed-time stepping scheme reflecting its digital implementation, whereas a circuit simulation usually employs an adaptive time stepping scheme in order to account for a wide range of time constants within the circuit model. In order to maintain the characteristic of both models as well as to facilitate model replacement, we treat them separately by means of input/output relations and propose an application of a waveform relaxation algorithm. Furthermore, the maximum and minimum number of iterations of the proposed algorithm are mathematically analyzed. The concept of controller/circuit coupling is illustrated by an example of the co-simulation of a PI power converter controller and a model of the main dipole circuit of the Large Hadron Collider.
△ Less
Submitted 10 April, 2017;
originally announced April 2017.
-
Optimized Field/Circuit Coupling for the Simulation of Quenches in Superconducting Magnets
Authors:
Idoia Cortes Garcia,
Sebastian Schöps,
Michał Maciejewski,
Lorenzo Bortot,
Marco Prioli,
Bernhard Auchmann,
Arjan Verweij
Abstract:
In this paper, we propose an optimized field/circuit coupling approach for the simulation of magnetothermal transients in superconducting magnets. The approach improves the convergence of the iterative coupling scheme between a magnetothermal partial differential model and an electrical lumped-element circuit. Such a multi-physics, multi-rate and multi-scale problem requires a consistent formulati…
▽ More
In this paper, we propose an optimized field/circuit coupling approach for the simulation of magnetothermal transients in superconducting magnets. The approach improves the convergence of the iterative coupling scheme between a magnetothermal partial differential model and an electrical lumped-element circuit. Such a multi-physics, multi-rate and multi-scale problem requires a consistent formulation and a dedicated framework to tackle the challenging transient effects occurring at both circuit and magnet level during normal operation and in case of faults. We derive an equivalent magnet model at the circuit side for the linear and the non-linear settings and discuss the convergence of the overall scheme in the framework of optimized Schwarz methods. The efficiency of the developed approach is illustrated by a numerical example of an accelerator dipole magnet with accompanying protection system.
△ Less
Submitted 6 July, 2017; v1 submitted 3 February, 2017;
originally announced February 2017.
-
Testing Beam-Induced Quench Levels of LHC Superconducting Magnets
Authors:
B. Auchmann,
T. Baer,
M. Bednarek,
G. Bellodi,
C. Bracco,
R. Bruce,
F. Cerutti,
V. Chetvertkova,
B. Dehning,
P. P. Granieri,
W. Hofle,
E. B. Holzer,
A. Lechner,
E. Nebot Del Busto,
A. Priebe,
S. Redaelli,
B. Salvachua,
M. Sapinski,
R. Schmidt,
N. Shetty,
E. Skordis,
M. Solfaroli,
J. Steckert,
D. Valuch,
A. Verweij
, et al. (3 additional authors not shown)
Abstract:
In the years 2009-2013 the Large Hadron Collider (LHC) has been operated with the top beam energies of 3.5 TeV and 4 TeV per proton (from 2012) instead of the nominal 7 TeV. The currents in the superconducting magnets were reduced accordingly. To date only seventeen beam-induced quenches have occurred; eight of them during specially designed quench tests, the others during injection. There has not…
▽ More
In the years 2009-2013 the Large Hadron Collider (LHC) has been operated with the top beam energies of 3.5 TeV and 4 TeV per proton (from 2012) instead of the nominal 7 TeV. The currents in the superconducting magnets were reduced accordingly. To date only seventeen beam-induced quenches have occurred; eight of them during specially designed quench tests, the others during injection. There has not been a single beam- induced quench during normal collider operation with stored beam. The conditions, however, are expected to become much more challenging after the long LHC shutdown. The magnets will be operating at near nominal currents, and in the presence of high energy and high intensity beams with a stored energy of up to 362 MJ per beam. In this paper we summarize our efforts to understand the quench levels of LHC superconducting magnets. We describe beam-loss events and dedicated experiments with beam, as well as the simulation methods used to reproduce the observable signals. The simulated energy deposition in the coils is compared to the quench levels predicted by electro-thermal models, thus allowing to validate and improve the models which are used to set beam-dump thresholds on beam-loss monitors for Run 2.
△ Less
Submitted 26 June, 2015; v1 submitted 18 February, 2015;
originally announced February 2015.
-
Models and experimental results from the wide aperture Nb-Ti magnets for the LHC upgrade
Authors:
G. Kirby,
B. Auchmann,
M. Bajko,
M. Charrondiere,
N. Bourcey,
V. I. Datskov,
P. Fessia,
J. Feuvrier,
P. Galbraith,
A. Garcia Tabares,
J. Garcia-Perez,
P. Granieri,
P. Hagen,
C. Lorin,
J. C. Perez,
S. Russenschuck,
T. Sahner,
M. Segreti,
E. Todesco,
G. Willering
Abstract:
MQXC is a Nb-Ti quadrupole designed to meet the accelerator quality requirements needed for the phase-1 LHC upgrade, now superseded by the high luminosity upgrade foreseen in 2021. The 2-m-long model magnet was tested at room temperature and 1.9 K. The technology developed for this magnet is relevant for other magnets currently under development for the high-luminosity upgrade, namely D1 (at KEK)…
▽ More
MQXC is a Nb-Ti quadrupole designed to meet the accelerator quality requirements needed for the phase-1 LHC upgrade, now superseded by the high luminosity upgrade foreseen in 2021. The 2-m-long model magnet was tested at room temperature and 1.9 K. The technology developed for this magnet is relevant for other magnets currently under development for the high-luminosity upgrade, namely D1 (at KEK) and the large aperture twin quadrupole Q4 (at CEA). In this paper we present MQXC test results, some of the specialized heat extraction features, spot heaters, temperature sensor mounting and voltage tap development for the special open cable insulation. We look at some problem solving with noisy signals, give an overview of electrical testing, look at how we calculate the coil resistance during at quench and show that the heaters are not working We describe the quench signals and its timing, the development of the quench heaters and give an explanation of an Excel quench calculation and its comparison including the good agreement with the MQXC test results. We propose an improvement to the magnet circuit design to reduce voltage to ground values by factor 2. The program is then used to predict quench Hot-Spot and Voltages values for the D1 dipole and the Q4 quadrupole.
△ Less
Submitted 16 January, 2014;
originally announced January 2014.
-
Experimental results and analysis from the 11 T Nb3Sn DS dipole
Authors:
G. Chlachidze,
I. Novitski,
A. V. Zlobin,
B. Auchmann,
M. Karppinen
Abstract:
FNAL and CERN are developing a 5.5-m-long twin-aperture Nb3Sn dipole suitable for installation in the LHC. A 2-m-long single-aperture demonstrator dipole with 60 mm bore, a nominal field of 11 T at the LHC nominal current of 11.85 kA and 20% margin has been developed and tested. This paper presents the results of quench protection analysis and protection heater study for the Nb3Sn demonstrator dip…
▽ More
FNAL and CERN are developing a 5.5-m-long twin-aperture Nb3Sn dipole suitable for installation in the LHC. A 2-m-long single-aperture demonstrator dipole with 60 mm bore, a nominal field of 11 T at the LHC nominal current of 11.85 kA and 20% margin has been developed and tested. This paper presents the results of quench protection analysis and protection heater study for the Nb3Sn demonstrator dipole. Extrapolations of the results for long magnet and operation in LHC are also presented.
△ Less
Submitted 16 January, 2014;
originally announced January 2014.
