-
The Analytical Method algorithm for trigger primitives generation at the LHC Drift Tubes detector
Authors:
G. Abbiendi,
J. Alcaraz Maestre,
A. Álvarez Fernández,
B. Álvarez González,
N. Amapane,
I. Bachiller,
L. Barcellan,
C. Baldanza,
C. Battilana,
M. Bellato,
G. Bencze,
M. Benettoni,
N. Beni,
A. Benvenuti,
A. Bergnoli,
L. C. Blanco Ramos,
L. Borgonovi,
A. Bragagnolo,
V. Cafaro,
A. Calderon,
E. Calvo,
R. Carlin,
C. A. Carrillo Montoya,
F. R. Cavallo,
J. M. Cela Ruiz
, et al. (121 additional authors not shown)
Abstract:
The Compact Muon Solenoid (CMS) experiment prepares its Phase-2 upgrade for the high-luminosity era of the LHC operation (HL-LHC). Due to the increase of occupancy, trigger latency and rates, the full electronics of the CMS Drift Tube (DT) chambers will need to be replaced. In the new design, the time bin for the digitisation of the chamber signals will be of around 1~ns, and the totality of the s…
▽ More
The Compact Muon Solenoid (CMS) experiment prepares its Phase-2 upgrade for the high-luminosity era of the LHC operation (HL-LHC). Due to the increase of occupancy, trigger latency and rates, the full electronics of the CMS Drift Tube (DT) chambers will need to be replaced. In the new design, the time bin for the digitisation of the chamber signals will be of around 1~ns, and the totality of the signals will be forwarded asynchronously to the service cavern at full resolution. The new backend system will be in charge of building the trigger primitives of each chamber. These trigger primitives contain the information at chamber level about the muon candidates position, direction, and collision time, and are used as input in the L1 CMS trigger. The added functionalities will improve the robustness of the system against ageing. An algorithm based on analytical solutions for reconstructing the DT trigger primitives, called Analytical Method, has been implemented both as a software C++ emulator and in firmware. Its performance has been estimated using the software emulator with simulated and real data samples, and through hardware implementation tests. Measured efficiencies are 96 to 98\% for all qualities and time and spatial resolutions are close to the ultimate performance of the DT chambers. A prototype chain of the HL-LHC electronics using the Analytical Method for trigger primitive generation has been installed during Long Shutdown 2 of the LHC and operated in CMS cosmic data taking campaigns in 2020 and 2021. Results from this validation step, the so-called Slice Test, are presented.
△ Less
Submitted 3 February, 2023;
originally announced February 2023.
-
Further studies on the physics potential of an experiment using LHC neutrinos
Authors:
N. Beni,
M. Brucoli,
V. Cafaro,
F. Cerutti,
G. M. Dallavalle,
S. Danzeca,
A. DeRoeck,
A. De Rujula,
D. Fasanella,
V. Giordano,
C. Guandalini,
A. Ioannisyan,
D. Lazic,
A. Margotti,
S. Lo Meo,
F. L. Navarria,
L. Patrizii,
T. Rovelli,
M. Sabate-Gilarte,
F. Sanchez Galan,
P. Santos Diaz,
G. Sirri,
Z. Szillasi,
C. -E. Wulz
Abstract:
We discuss an experiment to investigate neutrino physics at the LHC in Run 3, with emphasis on tau flavour. As described in our previous paper [arXiv:1903.06564v1], the detector can be installed in the decommissioned TI18 tunnel, about 480 m downstream the ATLAS cavern, after the first bending dipoles of the LHC arc. In that location, the prolongation of the beam Line-of-Sight from Interaction Poi…
▽ More
We discuss an experiment to investigate neutrino physics at the LHC in Run 3, with emphasis on tau flavour. As described in our previous paper [arXiv:1903.06564v1], the detector can be installed in the decommissioned TI18 tunnel, about 480 m downstream the ATLAS cavern, after the first bending dipoles of the LHC arc. In that location, the prolongation of the beam Line-of-Sight from Interaction Point IP1 to TI18 traverses about 100 m of rock. The detector intercepts the intense neutrino flux, generated by the LHC beams colliding in IP1, at large pseudorapidity eta, where neutrino energies can exceed a TeV. This paper focuses on optimizing global features of the experiment, like detector mass and acceptance. Since the neutrino-nucleon interaction cross section grows almost linearly with energy, the detector can be light and still collect a considerable sample of neutrino events; in the present study it weighs less than 3 tons. The detector is positioned off the beam axis, slightly above the ideal prolongation of the LHC beam from the straight section, covering 7.4 < eta < 9.2. In this configuration, the flux at high energies (0.5-1.5 TeV and beyond) is found to be dominated by neutrinos originating directly from IP1, mostly from charm decays, of which about 50% are electron neutrinos and about 5% are tau neutrinos. The contribution of pion and kaon decays to the muon neutrino flux is studied by means of simulations that embed the LHC optics and found small at high energies. The above studies indicate that with 150 /fb of delivered LHC luminosity in Run 3 the experiment can record a few thousand very high energy neutrino charged current interactions and over 50 tau neutrino charged current events.
△ Less
Submitted 16 April, 2020;
originally announced April 2020.
-
Study of the effects of radiation on the CMS Drift Tubes Muon Detector for the HL-LHC
Authors:
G. Abbiendi,
J. Alcaraz Maestre,
A. Álvarez Fernández,
B. Álvarez González,
N. Amapane,
I. Bachiller,
J. M. Barcala,
L. Barcellan,
C. Battilana,
M. Bellato,
G. Bencze,
M. Benettoni,
N. Beni,
A. Benvenuti,
L. C. Blanco Ramos,
A. Boletti,
A. Bragagnolo,
J. A. Brochero Cifuentes,
V. Cafaro,
A. Calderon,
E. Calvo,
A. Cappati,
R. Carlin,
C. A. Carrillo Montoya,
F. R. Cavallo
, et al. (118 additional authors not shown)
Abstract:
The CMS drift tubes (DT) muon detector, built for withstanding the LHC expected integrated and instantaneous luminosities, will be used also in the High Luminosity LHC (HL-LHC) at a 5 times larger instantaneous luminosity and, consequently, much higher levels of radiation, reaching about 10 times the LHC integrated luminosity. Initial irradiation tests of a spare DT chamber at the CERN gamma irrad…
▽ More
The CMS drift tubes (DT) muon detector, built for withstanding the LHC expected integrated and instantaneous luminosities, will be used also in the High Luminosity LHC (HL-LHC) at a 5 times larger instantaneous luminosity and, consequently, much higher levels of radiation, reaching about 10 times the LHC integrated luminosity. Initial irradiation tests of a spare DT chamber at the CERN gamma irradiation facility (GIF++), at large ($\sim$O(100)) acceleration factor, showed ageing effects resulting in a degradation of the DT cell performance. However, full CMS simulations have shown almost no impact in the muon reconstruction efficiency over the full barrel acceptance and for the full integrated luminosity. A second spare DT chamber was moved inside the GIF++ bunker in October 2017. The chamber was being irradiated at lower acceleration factors, and only 2 out of the 12 layers of the chamber were switched at working voltage when the radioactive source was active, being the other layers in standby. In this way the other non-aged layers are used as reference and as a precise and unbiased telescope of muon tracks for the efficiency computation of the aged layers of the chamber, when set at working voltage for measurements. An integrated dose equivalent to two times the expected integrated luminosity of the HL-LHC run has been absorbed by this second spare DT chamber and the final impact on the muon reconstruction efficiency is under study. Direct inspection of some extracted aged anode wires presented a melted resistive deposition of materials. Investigation on the outgassing of cell materials and of the gas components used at the GIF++ are underway. Strategies to mitigate the ageing effects are also being developed. From the long irradiation measurements of the second spare DT chamber, the effects of radiation in the performance of the DTs expected during the HL-LHC run will be presented.
△ Less
Submitted 12 December, 2019;
originally announced December 2019.
-
XSEN: a $ν$N Cross Section Measurement using High Energy Neutrinos from pp collisions at the LHC
Authors:
N. Beni,
S. Buontempo,
T. Camporesi,
F. Cerutti,
G. M. Dallavalle,
G. De Lellis,
A. De Roeck,
A. De Rujula,
A. Di Crescenzo,
D. Fasanella,
A. Ioannisyan,
D. Lazic,
A. Margotti,
S. Lo Meo,
F. L. Navarria,
L. Patrizii,
T. Rovelli,
M. Sabate-Gilarte,
F. Sanchez Galan,
P. Santos Diaz,
G. Sirri,
Z. Szillasi,
C. Wulz
Abstract:
XSEN (Cross Section of Energetic Neutrinos) is a small experiment designed to study, for the first time, neutrino-nucleon interactions (including the tau flavour) in the 0.5-1 TeV neutrino energy range. The detector will be installed in the decommissioned TI18 tunnel and uses nuclear emulsions. Its simplicity allows construction and installation before the LHC Run 3, 2021-2023; with 150/fb in Run3…
▽ More
XSEN (Cross Section of Energetic Neutrinos) is a small experiment designed to study, for the first time, neutrino-nucleon interactions (including the tau flavour) in the 0.5-1 TeV neutrino energy range. The detector will be installed in the decommissioned TI18 tunnel and uses nuclear emulsions. Its simplicity allows construction and installation before the LHC Run 3, 2021-2023; with 150/fb in Run3, the experiment can record up to two thousand neutrino interactions, and up to a hundred tau neutrino events. The XSEN detector intercepts the intense neutrino flux, generated by the LHC beams colliding in IP1, at large pseudo-rapidities, where neutrino energies can exceed the TeV. Since the neutrino-N interaction cross section grows almost linearly with energy, the detector can be light and still collect a considerable sample of neutrino interactions. In our proposal, the detector weighs less than 3 tons. It is lying slightly above the ideal prolongation of the LHC beam from the straight section; this configuration, off the beam axis, although very close to it, enhances the contribution of neutrinos from c and b decays, and consequently of tau neutrinos. The detector fits in the TI18 tunnel without modifications. We plan for a demonstrator experiment in 2021 with a small detector of about 0.5 tons; with 25/fb, nearly a hundred interactions of neutrinos of about 1 TeV can be recorded. The aim of this pilot run is a good in-situ characterisation of the machine-generated backgrounds, an experimental verification of the systematic uncertainties and efficiencies, and a tuning of the emulsion analysis infrastructure and efficiency. This Letter provides an overview of the experiment motivations, location, design constraints, technology choice, and operation.
△ Less
Submitted 24 October, 2019;
originally announced October 2019.
-
Physics Potential of an Experiment using LHC Neutrinos
Authors:
N. Beni,
M. Brucoli,
S. Buontempo,
V. Cafaro,
G . M. Dallavalle,
S. Danzeca,
G. De Lellis,
A. Di Crescenzo,
V. Giordano,
C. Guandalini,
D. Lazic,
S. Lo Meo,
F. L. Navarria,
Z. Szillasi
Abstract:
Production of neutrinos is abundant at LHC. Flavour composition and energy reach of the neutrino flux from proton-proton collisions depend on the pseudorapidity $η$. At large $η$, energies can exceed the TeV, with a sizeable contribution of the $τ$ flavour. A dedicated detector could intercept this intense neutrino flux in the forward direction, and measure the interaction cross section on nucleon…
▽ More
Production of neutrinos is abundant at LHC. Flavour composition and energy reach of the neutrino flux from proton-proton collisions depend on the pseudorapidity $η$. At large $η$, energies can exceed the TeV, with a sizeable contribution of the $τ$ flavour. A dedicated detector could intercept this intense neutrino flux in the forward direction, and measure the interaction cross section on nucleons in the unexplored energy range from a few hundred GeV to a few TeV. The high energies of neutrinos result in a larger $ν$N interaction cross section, and the detector size can be relatively small. Machine backgrounds vary rapidly while moving along and away from the beam line. Four locations were considered as hosts for a neutrino detector: the CMS quadruplet region (~25 m from CMS Interaction Point (IP)), UJ53 and UJ57 (90 and 120 m from CMS IP), RR53 and RR57 (240 m from CMS IP), TI18 (480 m from ATLAS IP). The potential sites are studied on the basis of (a) expectations for neutrino interaction rates, flavour composition and energy spectrum, (b) predicted backgrounds and in-situ measurements, performed with a nuclear emulsion detector and radiation monitors. TI18 emerges as the most favourable location. A small detector in TI18 could measure, for the first time, the high-energy $ν$N cross section, and separately for $τ$ neutrinos, with good precision, already with 300 fb$^{-1}$ in the LHC Run3.
△ Less
Submitted 15 March, 2019;
originally announced March 2019.
-
Measurement of the 235U(n,f) cross section relative to the 6Li(n,t) and 10B(n,alpha) standards from thermal to 170 keV neutron energy range at n_TOF
Authors:
S. Amaducci,
L. Cosentino,
M. Barbagallo,
N. Colonna,
A. Mengoni,
C. Massimi,
S. Lo Meo,
P. Finocchiaro,
O. Aberle,
J. Andrzejewski,
L. Audouin,
M. Bacak,
J. Balibrea,
F. Bečvář,
E. Berthoumieux,
J. Billowes,
D. Bosnar,
A. Brown,
M. Caamaño,
F. Calviño,
M. Calviani,
D. Cano-Ott,
R. Cardella,
A. Casanovas,
F. Cerutti
, et al. (96 additional authors not shown)
Abstract:
The 235U(n,f) cross section was measured in a wide energy range at n_TOF relative to 6Li(n,t) and 10B(n,alpha), with high resolution and in a wide energy range, with a setup based on a stack of six samples and six silicon detectors placed in the neutron beam. This allowed us to make a direct comparison of the reaction yields under the same experimental conditions, and taking into account the forwa…
▽ More
The 235U(n,f) cross section was measured in a wide energy range at n_TOF relative to 6Li(n,t) and 10B(n,alpha), with high resolution and in a wide energy range, with a setup based on a stack of six samples and six silicon detectors placed in the neutron beam. This allowed us to make a direct comparison of the reaction yields under the same experimental conditions, and taking into account the forward/backward emission asymmetry. A hint of an anomaly in the 10÷30 keV neutron energy range had been previously observed in other experiments, indicating a cross section systematically lower by several percent relative to major evaluations. The present results indicate that the evaluated cross section in the 9÷18 keV neutron energy range is indeed overestimated, both in the recent updates of ENDF/B-VIII.0 and of the IAEA reference data. Furthermore, these new high-resolution data confirm the existence of resonance-like structures in the keV neutron energy region. The new, high accuracy results here reported may lead to a reduction of the uncertainty in the 1÷100 keV neutron energy region. Finally, the present data provide additional confidence on the recently re-evaluated cross section integral between 7.8 and 11 eV.
△ Less
Submitted 4 March, 2019; v1 submitted 27 February, 2019;
originally announced February 2019.
-
Experimental setup and procedure for the measurement of the 7Be(n,α)α reaction at n_TOF
Authors:
L. Cosentino,
A. Musumarra,
M. Barbagallo,
A. Pappalardo,
N. Colonna,
L. Damone,
M. Piscopo,
P. Finocchiaro,
E. Maugeri,
S. Heinitz,
D. Schumann,
R. Dressler,
N. Kivel,
O. Aberle,
J. Andrzejewski,
L. Audouin,
M. Ayranov,
M. Bacak,
S. Barros,
J. Balibrea-Correa,
V. Beecares,
F. Becvar,
C. Beinrucker,
E. Berthoumieux,
J. Billowes
, et al. (107 additional authors not shown)
Abstract:
The newly built second experimental area EAR2 of the n_TOF spallation neutron source at CERN allows to perform (n, charged particles) experiments on short-lived highly radioactive targets. This paper describes a detection apparatus and the experimental procedure for the determination of the cross-section of the 7Be(n,α) reaction, which represents one of the focal points toward the solution of the…
▽ More
The newly built second experimental area EAR2 of the n_TOF spallation neutron source at CERN allows to perform (n, charged particles) experiments on short-lived highly radioactive targets. This paper describes a detection apparatus and the experimental procedure for the determination of the cross-section of the 7Be(n,α) reaction, which represents one of the focal points toward the solution of the cosmological Lithium abundance problem, and whose only measurement, at thermal energy, dates back to 1963. The apparently unsurmountable experimental difficulties stemming from the huge 7Be γ-activity, along with the lack of a suitable neutron beam facility, had so far prevented further measurements. The detection system is subject to considerable radiation damage, but is capable of disentangling the rare reaction signals from the very high background. This newly developed setup could likely be useful also to study other challenging reactions requiring the detectors to be installed directly in the neutron beam.
△ Less
Submitted 1 April, 2016;
originally announced April 2016.
-
SuperB Technical Design Report
Authors:
SuperB Collaboration,
M. Baszczyk,
P. Dorosz,
J. Kolodziej,
W. Kucewicz,
M. Sapor,
A. Jeremie,
E. Grauges Pous,
G. E. Bruno,
G. De Robertis,
D. Diacono,
G. Donvito,
P. Fusco,
F. Gargano,
F. Giordano,
F. Loddo,
F. Loparco,
G. P. Maggi,
V. Manzari,
M. N. Mazziotta,
E. Nappi,
A. Palano,
B. Santeramo,
I. Sgura,
L. Silvestris
, et al. (384 additional authors not shown)
Abstract:
In this Technical Design Report (TDR) we describe the SuperB detector that was to be installed on the SuperB e+e- high luminosity collider. The SuperB asymmetric collider, which was to be constructed on the Tor Vergata campus near the INFN Frascati National Laboratory, was designed to operate both at the Upsilon(4S) center-of-mass energy with a luminosity of 10^{36} cm^{-2}s^{-1} and at the tau/ch…
▽ More
In this Technical Design Report (TDR) we describe the SuperB detector that was to be installed on the SuperB e+e- high luminosity collider. The SuperB asymmetric collider, which was to be constructed on the Tor Vergata campus near the INFN Frascati National Laboratory, was designed to operate both at the Upsilon(4S) center-of-mass energy with a luminosity of 10^{36} cm^{-2}s^{-1} and at the tau/charm production threshold with a luminosity of 10^{35} cm^{-2}s^{-1}. This high luminosity, producing a data sample about a factor 100 larger than present B Factories, would allow investigation of new physics effects in rare decays, CP Violation and Lepton Flavour Violation. This document details the detector design presented in the Conceptual Design Report (CDR) in 2007. The R&D and engineering studies performed to arrive at the full detector design are described, and an updated cost estimate is presented.
A combination of a more realistic cost estimates and the unavailability of funds due of the global economic climate led to a formal cancelation of the project on Nov 27, 2012.
△ Less
Submitted 24 June, 2013;
originally announced June 2013.
