-
A cryogenic tracking detector for antihydrogen detection in the AEgIS experiment
Authors:
C. Amsler,
M. Antonello,
A. Belov,
G. Bonomi,
R. S. Brusa,
M. Caccia,
A. Camper,
R. Caravita,
F. Castelli,
D. Comparat,
G. Consolati,
A. Demetrio,
L. Di Noto,
M. Doser,
P. A. Ekman,
M. Fani,
R. Ferragut,
S. Gerber,
M. Giammarchi,
A. Gligorova,
F. Guatieri,
P. Hackstock,
D. Haider,
S. Haider,
A. Hinterberger
, et al. (33 additional authors not shown)
Abstract:
We present the commissioning of the Fast Annihilation Cryogenic Tracker detector (FACT), installed around the antihydrogen production trap inside the 1 T superconducting magnet of the AEgIS experiment. FACT is designed to detect pions originating from the annihilation of antiprotons. Its 794 scintillating fibers operate at 4 K and are read out by silicon photomultipliers (MPPCs) at near room tempe…
▽ More
We present the commissioning of the Fast Annihilation Cryogenic Tracker detector (FACT), installed around the antihydrogen production trap inside the 1 T superconducting magnet of the AEgIS experiment. FACT is designed to detect pions originating from the annihilation of antiprotons. Its 794 scintillating fibers operate at 4 K and are read out by silicon photomultipliers (MPPCs) at near room temperature. FACT provides the antiproton/antihydrogen annihilation position information with a few ns timing resolution. We present the hardware and software developments which led to the successful operation of the detector for antihydrogen detection and the results of an antiproton-loss based efficiency assessment. The main background to the antihydrogen signal is that of the positrons impinging onto the positronium conversion target and creating a large amount of gamma rays which produce a sizeable signal in the MPPCs shortly before the antihydrogen signal is expected. We detail the characterization of this background signal and its impact on the antihydrogen detection efficiency.
△ Less
Submitted 6 March, 2022;
originally announced March 2022.
-
Efficient $2^3S$ positronium production by stimulated decay from the $3^3P$ level
Authors:
M. Antonello,
A. Belov,
G. Bonomi,
R. S. Brusa,
M. Caccia,
A. Camper,
R. Caravita,
F. Castelli,
G. Cerchiari,
D. Comparat,
G. Consolati,
A. Demetrio,
L. Di Noto,
M. Doser,
M. Fanì,
S. Gerber,
A. Gligorova,
F. Guatieri,
P. Hackstock,
S. Haider,
A. Hinterberger,
A. Kellerbauer,
O. Khalidova,
D. Krasnicky,
V. Lagomarsino
, et al. (26 additional authors not shown)
Abstract:
We investigate experimentally the possibility of enhancing the production of $2^3S$ positronium atoms by driving the $1^3S$-$3^3P$ and $3^3P$-$2^3S$ transitions, overcoming the natural branching ratio limitation of spontaneous decay from $3^3P$ to $2^3S$. The decay of $3^3P$ positronium atoms towards the $2^3S$ level has been effciently stimulated by a 1312.2nm broadband IR laser pulse. The depend…
▽ More
We investigate experimentally the possibility of enhancing the production of $2^3S$ positronium atoms by driving the $1^3S$-$3^3P$ and $3^3P$-$2^3S$ transitions, overcoming the natural branching ratio limitation of spontaneous decay from $3^3P$ to $2^3S$. The decay of $3^3P$ positronium atoms towards the $2^3S$ level has been effciently stimulated by a 1312.2nm broadband IR laser pulse. The dependence of the stimulating transition efficiency on the intensity of the IR pulse has been measured to find the optimal enhancement conditions. A maximum relative increase of $ \times (3.1 \pm 1.0) $ in the $2^3S$ production efficiency, with respect to the case where only spontaneous decay is present, was obtained.
△ Less
Submitted 18 April, 2019;
originally announced April 2019.
-
The International Linear Collider. A Global Project
Authors:
Hiroaki Aihara,
Jonathan Bagger,
Philip Bambade,
Barry Barish,
Ties Behnke,
Alain Bellerive,
Mikael Berggren,
James Brau,
Martin Breidenbach,
Ivanka Bozovic-Jelisavcic,
Philip Burrows,
Massimo Caccia,
Paul Colas,
Dmitri Denisov,
Gerald Eigen,
Lyn Evans,
Angeles Faus-Golfe,
Brian Foster,
Keisuke Fujii,
Juan Fuster,
Frank Gaede,
Jie Gao,
Paul Grannis,
Christophe Grojean,
Andrew Hutton
, et al. (37 additional authors not shown)
Abstract:
A large, world-wide community of physicists is working to realise an exceptional physics program of energy-frontier, electron-positron collisions with the International Linear Collider (ILC). This program will begin with a central focus on high-precision and model-independent measurements of the Higgs boson couplings. This method of searching for new physics beyond the Standard Model is orthogonal…
▽ More
A large, world-wide community of physicists is working to realise an exceptional physics program of energy-frontier, electron-positron collisions with the International Linear Collider (ILC). This program will begin with a central focus on high-precision and model-independent measurements of the Higgs boson couplings. This method of searching for new physics beyond the Standard Model is orthogonal to and complements the LHC physics program. The ILC at 250 GeV will also search for direct new physics in exotic Higgs decays and in pair-production of weakly interacting particles. Polarised electron and positron beams add unique opportunities to the physics reach. The ILC can be upgraded to higher energy, enabling precision studies of the top quark and measurement of the top Yukawa coupling and the Higgs self-coupling. The key accelerator technology, superconducting radio-frequency cavities, has matured. Optimised collider and detector designs, and associated physics analyses, were presented in the ILC Technical Design Report, signed by 2400 scientists. There is a strong interest in Japan to host this international effort. A detailed review of the many aspects of the project is nearing a conclusion in Japan. Now the Japanese government is preparing for a decision on the next phase of international negotiations, that could lead to a project start within a few years. The potential timeline of the ILC project includes an initial phase of about 4 years to obtain international agreements, complete engineering design and prepare construction, and form the requisite international collaboration, followed by a construction phase of 9 years.
△ Less
Submitted 28 January, 2019;
originally announced January 2019.
-
The International Linear Collider. A European Perspective
Authors:
Philip Bambade,
Ties Behnke,
Mikael Berggren,
Ivanka Bozovic-Jelisavcic,
Philip Burrows,
Massimo Caccia,
Paul Colas,
Gerald Eigen,
Lyn Evans,
Angeles Faus-Golfe,
Brian Foster,
Juan Fuster,
Frank Gaede,
Christophe Grojean,
Marek Idzik,
Andrea Jeremie,
Tadeusz Lesiak,
Aharon Levy,
Benno List,
Jenny List,
Joachim Mnich,
Olivier Napoly,
Carlo Pagani,
Roman Poeschl,
Francois Richard
, et al. (9 additional authors not shown)
Abstract:
The International Linear Collider (ILC) being proposed in Japan is an electron-positron linear collider with an initial energy of 250 GeV. The ILC accelerator is based on the technology of superconducting radio-frequency cavities. This technology has reached a mature stage in the European XFEL project and is now widely used. The ILC will start by measuring the Higgs properties, providing high-prec…
▽ More
The International Linear Collider (ILC) being proposed in Japan is an electron-positron linear collider with an initial energy of 250 GeV. The ILC accelerator is based on the technology of superconducting radio-frequency cavities. This technology has reached a mature stage in the European XFEL project and is now widely used. The ILC will start by measuring the Higgs properties, providing high-precision and model-independent determinations of its parameters. The ILC at 250 GeV will also search for direct new physics in exotic Higgs decays and in pair-production of weakly interacting particles. The use of polarised electron and positron beams opens new capabilities and scenarios that add to the physics reach. The ILC can be upgraded to higher energy, enabling precision studies of the top quark and measurement of the top Yukawa coupling and the Higgs self-coupling. The international -- including European -- interest for the project is very strong. Europe has participated in the ILC project since its early conception and plays a major role in its present development covering most of its scientific and technological aspects: physics studies, accelerator and detectors. The potential for a wide participation of European groups and laboratories is thus high, including important opportunities for European industry. Following decades of technical development, R&D, and design optimisation, the project is ready for construction and the European particle physics community, technological centers and industry are prepared to participate in this challenging endeavour.
△ Less
Submitted 28 January, 2019;
originally announced January 2019.
-
Tests of a dual-readout fiber calorimeter with SiPM light sensors
Authors:
M. Antonello,
M. Caccia,
M. Cascella,
M. Dunser,
R. Ferrari,
S. Franchino,
G. Gaudio,
K. Hall,
J. Hauptman,
H. Jo,
K. Kang,
B. Kim,
S. Lee,
G. Lerner,
L. Pezzotti,
R. Santoro,
I. Vivarelli,
R. Ye,
R. Wigmans
Abstract:
In this paper, we describe the first tests of a dual-readout fiber calorimeter in which silicon photomultipliers are used to sense the (scintillation and Cherenkov) light signals. The main challenge in this detector is implementing a design that minimizes the optical crosstalk between the two types of fibers, which are located very close to each other and carry light signals that differ in intensi…
▽ More
In this paper, we describe the first tests of a dual-readout fiber calorimeter in which silicon photomultipliers are used to sense the (scintillation and Cherenkov) light signals. The main challenge in this detector is implementing a design that minimizes the optical crosstalk between the two types of fibers, which are located very close to each other and carry light signals that differ in intensity by about a factor of 60. The experimental data, which were obtained with beams of high-energy electrons and muons as well as in lab tests, illustrate to what extent this challenge was met. The Cherenkov light yield, a limiting factor for the energy resolution of this type of calorimeter, was measured to be about twice that of the previously tested configurations based on photomultiplier tubes. The lateral profiles of electromagnetic showers were measured on a scale of millimeters from the shower axis and significant differences were found between the profiles measured with the scintillating and the Cherenkov fibers.
△ Less
Submitted 8 May, 2018;
originally announced May 2018.
-
Measurement of antiproton annihilation on Cu, Ag and Au with emulsion films
Authors:
S. Aghion,
C. Amsler,
A. Ariga,
T. Ariga,
G. Bonomi,
P. Braunig,
R. S. Brusa,
L. Cabaret,
M. Caccia,
R. Caravita,
F. Castelli,
G. Cerchiari,
D. Comparat,
G. Consolati,
A. Demetrio,
L. Di Noto,
M. Doser,
A. Ereditato,
C. Evans,
R. Ferragut,
J. Fesel,
A. Fontana,
S. Gerber,
M. Giammarchi,
A. Gligorova
, et al. (47 additional authors not shown)
Abstract:
The characteristics of low energy antiproton annihilations on nuclei (e.g. hadronization and product multiplicities) are not well known, and Monte Carlo simulation packages that use different models provide different descriptions of the annihilation events. In this study, we measured the particle multiplicities resulting from antiproton annihilations on nuclei. The results were compared with predi…
▽ More
The characteristics of low energy antiproton annihilations on nuclei (e.g. hadronization and product multiplicities) are not well known, and Monte Carlo simulation packages that use different models provide different descriptions of the annihilation events. In this study, we measured the particle multiplicities resulting from antiproton annihilations on nuclei. The results were compared with predictions obtained using different models in the simulation tools GEANT4 and FLUKA. For this study, we exposed thin targets (Cu, Ag and Au) to a very low energy antiproton beam from CERN's Antiproton Decelerator, exploiting the secondary beamline available in the AEgIS experimental zone. The antiproton annihilation products were detected using emulsion films developed at the Laboratory of High Energy Physics in Bern, where they were analysed at the automatic microscope facility. The fragment multiplicity measured in this study is in good agreement with results obtained with FLUKA simulations for both minimally and heavily ionizing particles.
△ Less
Submitted 23 April, 2017; v1 submitted 23 January, 2017;
originally announced January 2017.
-
Infrastructure for Detector Research and Development towards the International Linear Collider
Authors:
J. Aguilar,
P. Ambalathankandy,
T. Fiutowski,
M. Idzik,
Sz. Kulis,
D. Przyborowski,
K. Swientek,
A. Bamberger,
M. Köhli,
M. Lupberger,
U. Renz,
M. Schumacher,
Andreas Zwerger,
A. Calderone,
D. G. Cussans,
H. F. Heath,
S. Mandry,
R. F. Page,
J. J. Velthuis,
D. Attié,
D. Calvet,
P. Colas,
X. Coppolani,
Y. Degerli,
E. Delagnes
, et al. (252 additional authors not shown)
Abstract:
The EUDET-project was launched to create an infrastructure for developing and testing new and advanced detector technologies to be used at a future linear collider. The aim was to make possible experimentation and analysis of data for institutes, which otherwise could not be realized due to lack of resources. The infrastructure comprised an analysis and software network, and instrumentation infras…
▽ More
The EUDET-project was launched to create an infrastructure for developing and testing new and advanced detector technologies to be used at a future linear collider. The aim was to make possible experimentation and analysis of data for institutes, which otherwise could not be realized due to lack of resources. The infrastructure comprised an analysis and software network, and instrumentation infrastructures for tracking detectors as well as for calorimetry.
△ Less
Submitted 23 January, 2012;
originally announced January 2012.
-
A Pixel Vertex Tracker for the TESLA Detector
Authors:
M. Battaglia,
M. Caccia,
S. Borghi,
R. Campagnolo,
K. Domanski,
P. Grabiec,
B. Jaroszewicz,
J. Marczewski,
D. Tomaszewski,
W. Kucewicz,
A. Zalewska,
K. Tammi
Abstract:
In order to fully exploit the physics potential of a e+e- linear collider, such as TESLA, a Vertex Tracker providing high resolution track reconstruction is required. Hybrid Silicon pixel sensors are an attractive sensor technology option due to their read-out speed and radiation hardness, favoured in the high rate TESLA environment, but have been so far limited by the achievable single point sp…
▽ More
In order to fully exploit the physics potential of a e+e- linear collider, such as TESLA, a Vertex Tracker providing high resolution track reconstruction is required. Hybrid Silicon pixel sensors are an attractive sensor technology option due to their read-out speed and radiation hardness, favoured in the high rate TESLA environment, but have been so far limited by the achievable single point space resolution. A novel layout of pixel detectors with interleaved cells to improve their spatial resolution is introduced and the results of the characterisation of a first set of test structures are discussed. In this note, a conceptual design of the TESLA Vertex Tracker, based on hybrid pixel sensors is presented
△ Less
Submitted 23 February, 2001;
originally announced February 2001.
-
Hybrid pixel detector development for the Linear collider Vertex Detector
Authors:
M. Battaglia,
M. Caccia,
S. Borghi,
R. Campagnolo,
W. Kucewicz,
H. Palka,
A. Zalewska
Abstract:
In order to fully exploit the Physics potential of future e+ e- linear collider, a Vertex Detector providing high resolution track reconstruction is required. Hybrid Silicon pixel detectors are an attractive option for the sensor technology due to their read-out speed and radiation hardness but have been so far limited by the achievable single point resolution. A novel layout of hybrid pixel sen…
▽ More
In order to fully exploit the Physics potential of future e+ e- linear collider, a Vertex Detector providing high resolution track reconstruction is required. Hybrid Silicon pixel detectors are an attractive option for the sensor technology due to their read-out speed and radiation hardness but have been so far limited by the achievable single point resolution. A novel layout of hybrid pixel sensor with interleaved cells to improve the spatial resolution has been developed. The characterisation of the first processed prototypes is reported.
△ Less
Submitted 16 January, 2001;
originally announced January 2001.
-
Characterisation of Hybrid Pixel Detectors with capacitive charge division
Authors:
M. Caccia,
S. Borghi,
R. Campagnolo,
M. Battaglia,
W. Kucewicz,
H. Palka,
A. Zalewska,
K. Domanski,
J. Marczewski,
D. Tomaszewski
Abstract:
In order to fully exploit the physics potential of the future high energy e+ e- linear collider, a Vertex Tracker providing high resolution track reconstruction is required. Hybrid pixel sensors are an attractive technology due to their fast read-out capabilities and radiation hardness. A novel pixel detector layout with interleaved cells between the readout nodes has been developed to improve t…
▽ More
In order to fully exploit the physics potential of the future high energy e+ e- linear collider, a Vertex Tracker providing high resolution track reconstruction is required. Hybrid pixel sensors are an attractive technology due to their fast read-out capabilities and radiation hardness. A novel pixel detector layout with interleaved cells between the readout nodes has been developed to improve the single point resolution. The results of the characterisation of the first processed prototypes are reported.
△ Less
Submitted 10 January, 2001;
originally announced January 2001.
-
The challenge of hybridization
Authors:
Massimo Caccia
Abstract:
Hybridization of pixel detector systems has to satisfy tight requirements: high yield, long term reliability, mechanical stability, thermal compliance and robustness have to go together with low passive mass added to the system, radiation hardness, flexibility in the technology end eventually low cost. The current technologies for the interconnection of the front-end chips and the sensor are rev…
▽ More
Hybridization of pixel detector systems has to satisfy tight requirements: high yield, long term reliability, mechanical stability, thermal compliance and robustness have to go together with low passive mass added to the system, radiation hardness, flexibility in the technology end eventually low cost. The current technologies for the interconnection of the front-end chips and the sensor are reviewed and compared, together with the solutions for the interface to the far-end electronics.
△ Less
Submitted 10 January, 2001;
originally announced January 2001.
-
Hybrid Pixel Detector Development for the Linear Collider Vertex Tracker
Authors:
M. Battaglia,
S. Borghi,
R. Campagnolo,
M. Caccia,
W. Kucewicz,
P. Jalocha,
J. Palka,
A. Zalewska
Abstract:
In order to fully exploit the physics potential of the future high energy e+e- linear collider, a Vertex Tracker able to provide particle track extrapolation with very high resolution is needed. Hybrid Si pixel sensors are an attractive technology due to their fast read-out capabilities and radiation hardness. A novel pixel detector layout with interleaved cells has been developed to improve the…
▽ More
In order to fully exploit the physics potential of the future high energy e+e- linear collider, a Vertex Tracker able to provide particle track extrapolation with very high resolution is needed. Hybrid Si pixel sensors are an attractive technology due to their fast read-out capabilities and radiation hardness. A novel pixel detector layout with interleaved cells has been developed to improve the single point resolution. Results of the characterisation of the first processed prototypes by electrostatic measurements and charge collection studies are discussed.
△ Less
Submitted 16 November, 2000;
originally announced November 2000.
-
The Vertex Tracker at the e+e- Linear Collider Conceptual Design, Detector R&D and Physics Performances for the Next Generation of Silicon Vertex Detectors
Authors:
Marco Battaglia,
Massimo Caccia
Abstract:
The e+e- linear collider physics programme sets highly demanding requirements on the accurate determination of charged particle trajectories close to their production point. A new generation of Vertex Trackers, based on different technologies of high resolution silicon sensors, is being developed to provide the needed performances. These developments are based on the experience with the LEP/SLC…
▽ More
The e+e- linear collider physics programme sets highly demanding requirements on the accurate determination of charged particle trajectories close to their production point. A new generation of Vertex Trackers, based on different technologies of high resolution silicon sensors, is being developed to provide the needed performances. These developments are based on the experience with the LEP/SLC vertex detectors and on the results of the R&D programs for the LHC trackers and also define a further program of R&D specific to the linear collider applications. In this paper the present status of the conceptual tracker design, silicon detector R&D and physics studies is discussed.
△ Less
Submitted 26 November, 1999;
originally announced November 1999.
-
High Resolution Hybrid Pixel Sensors for the e+e- TESLA Linear Collider Vertex Tracker
Authors:
M. Battaglia,
R. Orava,
K. Tammi,
K. Osterberg,
W. Kucewicz,
A. Zalewska,
M. Caccia,
R. Campagnolo,
C. Meroni,
P. Grabiec,
B. Jaroszewicz,
J. Marczewski
Abstract:
In order to fully exploit the physics potential of a future high energy e+e- linear collider, a Vertex Tracker, providing high resolution track reconstruction, is required. Hybrid Silicon pixel sensors are an attractive option, for the sensor technology, due to their read-out speed and radiation hardness, favoured in the high rate environment of the TESLA e+e- linear collider design but have bee…
▽ More
In order to fully exploit the physics potential of a future high energy e+e- linear collider, a Vertex Tracker, providing high resolution track reconstruction, is required. Hybrid Silicon pixel sensors are an attractive option, for the sensor technology, due to their read-out speed and radiation hardness, favoured in the high rate environment of the TESLA e+e- linear collider design but have been so far limited by the achievable single point space resolution. In this paper, a conceptual design of the TESLA Vertex Tracker, based on a novel layout of hybrid pixel sensors with interleaved cells to improve their spatial resolution, is presented.
△ Less
Submitted 11 November, 1999;
originally announced November 1999.
-
High resolution pixel detectors for e+e- linear colliders
Authors:
M. Caccia,
R. Campagnolo,
C. Meroni,
W. Kucewicz,
G. Deptuch,
A. Zalewska,
M. Battaglia,
K. Osterberg,
R. Orava,
S. Higueret,
M. Winter,
R. Turchetta,
P. Grabiec,
B. Jaroszewicz,
J. Marczewski
Abstract:
The physics goals at the future e+e- linear collider require high performance vertexing and impact parameter resolution. Two possible technologies for the vertex detector of an experimental apparatus are outlined in the paper: an evolution of the Hybrid Pixel Sensors already used in high energy physics experiments and a new detector concept based on the monolithic CMOS sensors.
The physics goals at the future e+e- linear collider require high performance vertexing and impact parameter resolution. Two possible technologies for the vertex detector of an experimental apparatus are outlined in the paper: an evolution of the Hybrid Pixel Sensors already used in high energy physics experiments and a new detector concept based on the monolithic CMOS sensors.
△ Less
Submitted 11 October, 1999;
originally announced October 1999.
