-
Complete Catalog of Laser Locking Configurations for LISA
Authors:
Gerhard Heinzel,
Javier Álvarez-Vizoso,
Miguel Dovale-Álvarez
Abstract:
The Laser Interferometer Space Antenna (LISA) will enable direct observations of low-frequency gravitational waves, offering unprecedented insight into astrophysical and cosmological phenomena. LISA's heterodyne interferometric measurement system requires phase-locking five of its six onboard lasers with tunable frequency offsets to ensure that all beatnotes remain within the metrology system's op…
▽ More
The Laser Interferometer Space Antenna (LISA) will enable direct observations of low-frequency gravitational waves, offering unprecedented insight into astrophysical and cosmological phenomena. LISA's heterodyne interferometric measurement system requires phase-locking five of its six onboard lasers with tunable frequency offsets to ensure that all beatnotes remain within the metrology system's operational range, despite Doppler-induced frequency shifts. The selection of these offset frequencies -- collectively forming a frequency plan -- is a complex optimization problem constrained by the spacecraft's orbital dynamics and instrument limitations. While previous work established an algorithmic solution for deriving time-dependent frequency plans, this study takes a complementary approach by systematically analyzing and cataloging all possible laser locking configurations. We present an automated method to explore, validate, and classify viable locking schemes, identifying 36 unique non-frequency-swapping configurations and 72 additional frequency-swapping configurations for an arbitrary choice of primary laser. This exhaustive classification provides a foundation for frequency planning across the full range of operational scenarios.
△ Less
Submitted 28 May, 2025;
originally announced May 2025.
-
Post-processing subtraction of tilt-to-length noise in LISA in the presence of gravitational wave signals
Authors:
Marie-Sophie Hartig,
Sarah Paczkowski,
Martin Hewitson,
Gerhard Heinzel,
Gudrun Wanner
Abstract:
The Laser Interferometer Space Antenna (LISA) will be the first space-based gravitational wave (GW) observatory. It will measure gravitational wave signals in the frequency regime from 0.1 mHz to 1 Hz. The success of these measurements will depend on the suppression of the various instrument noises. One important noise source in LISA will be tilt-to-length (TTL) coupling. Here, it is understood as…
▽ More
The Laser Interferometer Space Antenna (LISA) will be the first space-based gravitational wave (GW) observatory. It will measure gravitational wave signals in the frequency regime from 0.1 mHz to 1 Hz. The success of these measurements will depend on the suppression of the various instrument noises. One important noise source in LISA will be tilt-to-length (TTL) coupling. Here, it is understood as the coupling of angular jitter, predominantly from the spacecraft, into the interferometric length readout. The current plan is to subtract this noise in-flight in post-processing as part of a noise minimization strategy. It is crucial to distinguish TTL coupling well from the GW signals in the same readout to ensure that the noise will be properly modeled. Furthermore, it is important that the subtraction of TTL noise will not degrade the GW signals. In the present manuscript, we show on simulated LISA data and for four different GW signal types that the GW responses have little effect on the quality of the TTL coupling fit and subtraction. Also, the GW signal characteristics were not altered by the TTL coupling subtraction.
△ Less
Submitted 2 February, 2025; v1 submitted 21 November, 2024;
originally announced November 2024.
-
Design of Dedicated Tilt-to-Length Calibration Maneuvers for LISA
Authors:
Henry Wegener,
Sarah Paczkowski,
Marie-Sophie Hartig,
Martin Hewitson,
Gerhard Heinzel,
Gudrun Wanner
Abstract:
Tilts of certain elements within a laser interferometer can undesirably couple into measurements as a form of noise, known as tilt-to-length (TTL) coupling. This TTL coupling is anticipated to be one of the primary noise sources in the Laser Interferometer Space Antenna (LISA) mission, after Time Delay Interferometry (TDI) is applied. Despite the careful interferometer design and calibration on th…
▽ More
Tilts of certain elements within a laser interferometer can undesirably couple into measurements as a form of noise, known as tilt-to-length (TTL) coupling. This TTL coupling is anticipated to be one of the primary noise sources in the Laser Interferometer Space Antenna (LISA) mission, after Time Delay Interferometry (TDI) is applied. Despite the careful interferometer design and calibration on the ground, TTL is likely to require in-flight mitigation through post-processing subtraction to achieve the necessary sensitivity. Past research has demonstrated TTL subtraction in simulations through the estimation of 24 linear coupling coefficients using a noise minimization approach. This paper investigates an approach based on performing rotation maneuvers for estimating coupling coefficients with low uncertainties. In this study, we evaluate the feasibility and optimal configurations of such maneuvers to identify the most efficient solutions. We assess the efficacy of TTL calibration maneuvers by modulating either the spacecraft attitude or the Moving Optical Sub-Assembly (MOSA) yaw angle. We found that sinusoidal signals with amplitudes of around 30 nrad and frequencies near 43 mHz are practical and nearly optimal choices for such modulations. Employing different frequencies generates uncorrelated signals, allowing for multiple maneuvers to be executed simultaneously. Our simulations enable us to estimate the TTL coefficients with precision below 15 um/rad (1-sigma, in free space) after a total maneuver time of 20 minutes. The results are compared to the estimation uncertainties that can be achieved without using maneuvers.
△ Less
Submitted 15 November, 2024;
originally announced November 2024.
-
Clock synchronization and light-travel-time estimation for space-based gravitational-wave detectors
Authors:
Jan Niklas Reinhardt,
Olaf Hartwig,
Gerhard Heinzel
Abstract:
Space-based gravitational-wave detectors, such as LISA, record interferometric measurements on widely separated satellites. Their clocks are not synced actively. Instead, clock synchronization is performed in on-ground data processing. It relies on measurements of the so-called pseudoranges, which entangle the interspacecraft light travel times with the clock desynchronizations between emitting an…
▽ More
Space-based gravitational-wave detectors, such as LISA, record interferometric measurements on widely separated satellites. Their clocks are not synced actively. Instead, clock synchronization is performed in on-ground data processing. It relies on measurements of the so-called pseudoranges, which entangle the interspacecraft light travel times with the clock desynchronizations between emitting and receiving spacecraft. For interspacecraft clock synchronization, we need to isolate the differential clock desynchronizations, i.e., disentangle the pseudoranges. This further yields estimates for the interspacecraft light travel times, which are required as delays for the laser frequency noise suppression via time-delay interferometry. Previous studies on pseudorange disentanglement apply various simplifications in the pseudorange modeling and the data simulation. In contrast, this article derives an accurate pseudorange model in the barycentric celestial reference system, complemented by realistic state-of-the-art LISA data simulations. Concerning pseudorange disentanglement, this leads to an a priori under-determined system. We demonstrate how on-ground orbit determinations, as well as onboard transmission and on-ground reception time tags of the telemetry data, can be used to resolve this degeneracy. We introduce an algorithm for pseudorange disentanglement based on a nonstandard Kalman filter specially designed for clock synchronization in systems where pseudorange measurements are conducted in different time frames. This algorithm achieves interspacecraft clock synchronization and light travel time estimation with submeter accuracy, thus fulfilling the requirements of time-delay interferometry.
△ Less
Submitted 19 August, 2024;
originally announced August 2024.
-
Precision measurements of the magnetic parameters of LISA Pathfinder test masses
Authors:
M Armano,
H Audley,
J Baird,
P Binetruy,
M Born,
D Bortoluzzi,
E Castelli,
A Cavalleri,
A Cesarini,
A M Cruise,
K Danzmann,
M De Deus Silva,
I Diepholz,
G Dixon,
R Dolesi,
L Ferraioli,
V Ferroni,
E D Fitzsimons,
M Freschi,
L Gesa,
D Giardini,
F Gibert,
R Giusteri,
C Grimani,
J Grzymisch
, et al. (54 additional authors not shown)
Abstract:
A precise characterization of the magnetic properties of LISA Pathfinder free falling test-masses is of special interest for future gravitational wave observatory in space. Magnetic forces have an important impact on the instrument sensitivity in the low frequency regime below the millihertz. In this paper we report on the magnetic injection experiments performed throughout LISA Pathfinder operati…
▽ More
A precise characterization of the magnetic properties of LISA Pathfinder free falling test-masses is of special interest for future gravitational wave observatory in space. Magnetic forces have an important impact on the instrument sensitivity in the low frequency regime below the millihertz. In this paper we report on the magnetic injection experiments performed throughout LISA Pathfinder operations. We show how these experiments allowed a high precision estimate of the instrument magnetic parameters. The remanent magnetic moment was found to have a modulus of $(0.245\pm0.081)\,\rm{nAm}^2$, the x-component of the background magnetic field within the test masses position was measured to be $(414 \pm 74)$ nT and its gradient had a value of $(-7.4\pm 2.1)\,μ$T/m. Finally, we also measured the test mass magnetic susceptibility to be $(-3.35\pm0.15)\times$10$^{-5}$ in the low frequency regime. All results are in agreement with on-ground estimates.
△ Less
Submitted 5 November, 2024; v1 submitted 5 July, 2024;
originally announced July 2024.
-
Magnetic-induced force noise in LISA Pathfinder free-falling test masses
Authors:
M Armano,
H Audley,
J Baird,
P Binetruy,
M Born,
D Bortoluzzi,
E Castelli,
A Cavalleri,
A Cesarini,
A M Cruise,
K Danzmann,
M De Deus Silva,
I Diepholz,
G Dixon,
R Dolesi,
L Ferraioli,
V Ferroni,
E D Fitzsimons,
M Freschi,
L Gesa,
D Giardini,
F Gibert,
R Giusteri,
C Grimani,
J Grzymisch
, et al. (54 additional authors not shown)
Abstract:
LISA Pathfinder was a mission designed to test key technologies required for gravitational wave detection in space. Magnetically driven forces play a key role in the instrument sensitivity in the low-frequency regime, which corresponds to the measurement band of interest for future space-borne gravitational wave observatories. Magnetic-induced forces couple to the test mass motion, introducing a c…
▽ More
LISA Pathfinder was a mission designed to test key technologies required for gravitational wave detection in space. Magnetically driven forces play a key role in the instrument sensitivity in the low-frequency regime, which corresponds to the measurement band of interest for future space-borne gravitational wave observatories. Magnetic-induced forces couple to the test mass motion, introducing a contribution to the relative acceleration noise between the free falling test masses. In this Letter we present the first complete estimate of this term of the instrument performance model. Our results set the magnetic-induced acceleration noise during the February 2017 noise run of $\rm 0.25_{-0.08}^{+0.15}\,fm\,s^{-2}/\sqrt{Hz}$ at 1 mHz and $\rm 1.01_{-0.24}^{+0.73}\, fm\,s^{-2}/\sqrt{Hz}$ at 0.1 mHz. We also discuss how the non-stationarities of the interplanetary magnetic field can affect these values during extreme space weather conditions.
△ Less
Submitted 5 November, 2024; v1 submitted 5 July, 2024;
originally announced July 2024.
-
Time-delay interferometry with onboard optical delays
Authors:
Jan Niklas Reinhardt,
Philipp Euringer,
Olaf Hartwig,
Gerald Hechenblaikner,
Gerhard Heinzel,
Kohei Yamamoto
Abstract:
Time-delay interferometry (TDI) is a data processing technique for space-based gravitational-wave detectors to create laser-noise-free equal-optical-path-length interferometers virtually on the ground. It relies on the interspacecraft signal propagation delays, which are delivered by intersatellite ranging monitors. Also delays due to onboard signal propagation and processing have a nonnegligible…
▽ More
Time-delay interferometry (TDI) is a data processing technique for space-based gravitational-wave detectors to create laser-noise-free equal-optical-path-length interferometers virtually on the ground. It relies on the interspacecraft signal propagation delays, which are delivered by intersatellite ranging monitors. Also delays due to onboard signal propagation and processing have a nonnegligible impact on the TDI combinations. However, these onboard delays were only partially considered in previous TDI-related research; onboard optical path lengths have been neglected so far. In this paper, we study onboard optical path lengths in TDI. We derive analytical models for their coupling to the second-generation TDI Michelson combinations and verify these models numerically. Furthermore, we derive a compensation scheme for onboard optical path lengths in TDI and validate its performance via numerical simulations.
△ Less
Submitted 27 August, 2024; v1 submitted 30 May, 2024;
originally announced May 2024.
-
NanoNewton electrostatic force actuators for femtoNewton-sensitive measurements: system performance test in the LISA Pathfinder mission
Authors:
M Armano,
H Audley,
J Baird,
M Bassan,
P Binetruy,
M Born,
D Bortoluzzi,
E Castelli,
A Cavalleri,
A Cesarini,
V Chiavegato,
A M Cruise,
D Dal Bosco,
K Danzmann,
M De Deus Silva,
R De Rosa,
L Di Fiore,
I Diepholz,
G Dixon,
R Dolesi,
L Ferraioli V Ferroni,
E D Fitzsimons,
M Freschi,
L Gesa,
D Giardini
, et al. (65 additional authors not shown)
Abstract:
Electrostatic force actuation is a key component of the system of geodesic reference test masses (TM) for the LISA orbiting gravitational wave observatory and in particular for performance at low frequencies, below 1 mHz, where the observatory sensitivity is limited by stray force noise. The system needs to apply forces of order 10$^{-9}$ N while limiting fluctuations in the measurement band to le…
▽ More
Electrostatic force actuation is a key component of the system of geodesic reference test masses (TM) for the LISA orbiting gravitational wave observatory and in particular for performance at low frequencies, below 1 mHz, where the observatory sensitivity is limited by stray force noise. The system needs to apply forces of order 10$^{-9}$ N while limiting fluctuations in the measurement band to levels approaching 10$^{-15}$ N/Hz$^{1/2}$. We present here the LISA actuation system design, based on audio-frequency voltage carrier signals, and results of its in-flight performance test with the LISA Pathfinder test mission. In LISA, TM force actuation is used to align the otherwise free-falling TM to the spacecraft-mounted optical metrology system, without any forcing along the critical gravitational wave-sensitive interferometry axes. In LISA Pathfinder, on the other hand, the actuation was used also to stabilize the TM along the critical $x$ axis joining the two TM, with the commanded actuation force entering directly into the mission's main differential acceleration science observable. The mission allowed demonstration of the full compatibility of the electrostatic actuation system with the LISA observatory requirements, including dedicated measurement campaigns to amplify, isolate, and quantify the two main force noise contributions from the actuation system, from actuator gain noise and from low frequency ``in band'' voltage fluctuations. These campaigns have shown actuation force noise to be a relevant, but not dominant, noise source in LISA Pathfinder and have allowed performance projections for the conditions expected in the LISA mission.
△ Less
Submitted 30 December, 2023;
originally announced January 2024.
-
Radiation Tolerance of Low-Noise Photoreceivers for the LISA Space Mission
Authors:
P. Colcombet,
N. Dinu-Jaeger,
C. Inguimbert,
T. Nuns,
S. Bruhier,
N. Christensen,
P. Hofverberg,
N. van Bakel,
M. van Beuzekom,
T. Mistry,
G. Visser,
D. Pascucci,
K. Izumi,
K. Komori,
G. Heinzel,
G. Fernández Barranco,
J. J. M. in t Zand,
P. Laubert,
M. Frericks
Abstract:
This study investigates the effects of space environmental radiation on the performance of InGaAs Quadrant Photodiodes (QPDs) and assesses their suitability for the Laser Interferometer Space Antenna (LISA) mission. QPDs of 1.0, 1.5 and 2.0 mm have been irradiated with 20 and 60 MeV protons, 0.5 and 1 MeV electrons, and Co$^{60}$ gamma. An exposure corresponding to a displacement damage equivalent…
▽ More
This study investigates the effects of space environmental radiation on the performance of InGaAs Quadrant Photodiodes (QPDs) and assesses their suitability for the Laser Interferometer Space Antenna (LISA) mission. QPDs of 1.0, 1.5 and 2.0 mm have been irradiated with 20 and 60 MeV protons, 0.5 and 1 MeV electrons, and Co$^{60}$ gamma. An exposure corresponding to a displacement damage equivalent fluence of $1.0 \times 10^{+12}$ p/cm$^2$ for 20 and 60 MeV protons and a total ionizing dose of 237 krad were applied, surpassing the anticipated radiation levels for the LISA mission by a factor of approximately five. Experiments were conducted to measure changes in QPD dark current, capacitance, and responsivity. The QPDs are integrated with a low-noise DC-coupled transimpedance amplifier to form the Photoreceiver (QPR). QPR noise and performance in an interferometric system like LISA were also measured. Although radiation impacted their dark current and responsivity, almost all QPDs met LISA's validation criteria and did not demonstrate any critical failure. These findings prove that the tested QPDs are promising candidates for LISA and other space-based missions.
△ Less
Submitted 15 October, 2023;
originally announced October 2023.
-
Ranging Sensor Fusion in LISA Data Processing: Treatment of Ambiguities, Noise, and On-Board Delays in LISA Ranging Observables
Authors:
Jan Niklas Reinhardt,
Martin Staab,
Kohei Yamamoto,
Jean-Baptiste Bayle,
Aurélien Hees,
Olaf Hartwig,
Karsten Wiesner,
Sweta Shah,
Gerhard Heinzel
Abstract:
Interspacecraft ranging is crucial for the suppression of laser frequency noise via time-delay interferometry (TDI). So far, the effects of on-board delays and ambiguities on the LISA ranging observables were neglected in LISA modelling and data processing investigations. In reality, on-board delays cause offsets and timestamping delays in the LISA measurements, and pseudo-random noise (PRN) rangi…
▽ More
Interspacecraft ranging is crucial for the suppression of laser frequency noise via time-delay interferometry (TDI). So far, the effects of on-board delays and ambiguities on the LISA ranging observables were neglected in LISA modelling and data processing investigations. In reality, on-board delays cause offsets and timestamping delays in the LISA measurements, and pseudo-random noise (PRN) ranging is ambiguous, as it only determines the range up to an integer multiple of the PRN code length. In this article, we identify the four LISA ranging observables: PRN ranging, the sideband beatnotes at the interspacecraft interferometer, TDI ranging, and ground-based observations. We derive their observation equations in the presence of on-board delays, noise, and ambiguities. We then propose a three-stage ranging sensor fusion to combine these observables in order to gain accurate and precise ranging estimates. We propose to calibrate the on-board delays on ground and to compensate the associated offsets and timestamping delays in an initial data treatment (stage 1). We identify the ranging-related routines, which need to run continuously during operation (stage 2), and implement them numerically. Essentially, this involves the reduction of ranging noise, for which we develop a Kalman filter combining the PRN ranging and the sideband beatnotes. We further implement crosschecks for the PRN ranging ambiguities and offsets (stage 3). We show that both ground-based observations and TDI ranging can be used to resolve the PRN ranging ambiguities. Moreover, we apply TDI ranging to estimate the PRN ranging offsets.
△ Less
Submitted 16 January, 2024; v1 submitted 11 July, 2023;
originally announced July 2023.
-
The influence of laser relative intensity noise in the Laser Interferometer Space Antenna
Authors:
Lennart Wissel,
Olaf Hartwig,
Jean-Baptiste Bayle,
Martin Staab,
Ewan D. Fitzsimons,
Martin Hewitson,
Gerhard Heinzel
Abstract:
LISA is an upcoming ESA mission that will detect gravitational waves in space by interferometrically measuring the separation between free-falling test masses at picometer precision. To reach the desired performance, LISA will employ the noise reduction technique time-delay interferometry (TDI), in which multiple raw interferometric readouts are time shifted and combined into the final scientific…
▽ More
LISA is an upcoming ESA mission that will detect gravitational waves in space by interferometrically measuring the separation between free-falling test masses at picometer precision. To reach the desired performance, LISA will employ the noise reduction technique time-delay interferometry (TDI), in which multiple raw interferometric readouts are time shifted and combined into the final scientific observables. Evaluating the performance in terms of these TDI variables requires careful tracking of how different noise sources propagate through TDI, as noise correlations might affect the performance in unexpected ways. One example of such potentially correlated noise is the relative intensity noise (RIN) of the six lasers aboard the three LISA satellites, which will couple into the interferometric phase measurements. In this article, we calculate the expected RIN levels based on the current mission architecture and the envisaged mitigation strategies. We find that strict requirements on the technical design reduce the effect from approximately 8.7 pm/rtHz per inter-spacecraft interferometer to that of a much lower sub-1 pm/rtHz noise, with typical characteristics of an uncorrelated readout noise after TDI. Our investigations underline the importance of sufficient balanced detection of the interferometric measurements.
△ Less
Submitted 4 January, 2023; v1 submitted 22 December, 2022;
originally announced December 2022.
-
Temperature stability in the sub-milliHertz band with LISA Pathfinder
Authors:
M. Armano,
H. Audley,
J. Baird,
P. Binetruy,
M. Born,
D. Bortoluzzi,
E. Castelli,
A. Cavalleri,
A. Cesarini,
A. M. Cruise,
K. Danzmann,
M. de Deus Silva,
I. Diepholz,
G. Dixon,
R. Dolesi,
L. Ferraioli,
V. Ferroni,
E. D. Fitzsimons,
M. Freschi,
L. Gesa,
F. Gibert,
D. Giardini,
R. Giusteri,
C. Grimani,
J. Grzymisch
, et al. (57 additional authors not shown)
Abstract:
LISA Pathfinder (LPF) was a technology pioneering mission designed to test key technologies required for gravitational wave detection in space. In the low frequency regime (milli-Hertz and below), where space-based gravitational wave observatories will operate, temperature fluctuations play a crucial role since they can couple into the interferometric measurement and the test masses' free-fall acc…
▽ More
LISA Pathfinder (LPF) was a technology pioneering mission designed to test key technologies required for gravitational wave detection in space. In the low frequency regime (milli-Hertz and below), where space-based gravitational wave observatories will operate, temperature fluctuations play a crucial role since they can couple into the interferometric measurement and the test masses' free-fall accuracy in many ways. A dedicated temperature measurement subsystem, with noise levels in 10$\,μ$K$\,$Hz$^{-1/2}$ down to $1\,$mHz was part of the diagnostics unit on board LPF. In this paper we report on the temperature measurements throughout mission operations, characterize the thermal environment, estimate transfer functions between different locations and report temperature stability (and its time evolution) at frequencies as low as 10$\,μ$Hz, where typically values around $1\,$K$\,$Hz$^{-1/2}$ were measured.
△ Less
Submitted 22 May, 2019;
originally announced May 2019.
-
First stage of LISA data processing II: Alternative filtering dynamic models for LISA
Authors:
Yan Wang,
Gerhard Heinzel,
Karsten Danzmann
Abstract:
Space-borne gravitational wave detectors, such as (e)LISA, are designed to operate in the low-frequency band (mHz to Hz), where there is a variety of gravitational wave sources of great scientific value. To achieve the extraordinary sensitivity of these detector, the precise synchronization of the clocks on the separate spacecraft and the accurate determination of the interspacecraft distances are…
▽ More
Space-borne gravitational wave detectors, such as (e)LISA, are designed to operate in the low-frequency band (mHz to Hz), where there is a variety of gravitational wave sources of great scientific value. To achieve the extraordinary sensitivity of these detector, the precise synchronization of the clocks on the separate spacecraft and the accurate determination of the interspacecraft distances are important ingredients. In our previous paper (Phys. Rev. D 90, 064016 [2014]), we have described a hybrid-extend Kalman filter with a full state vector to do this job. In this paper, we explore several different state vectors and their corresponding (phenomenological) dynamic models, to reduce the redundancy in the full state vector, to accelerate the algorithm, and to make the algorithm easily extendable to more complicated scenarios.
△ Less
Submitted 28 March, 2015;
originally announced March 2015.
-
Free-flight experiments in LISA Pathfinder
Authors:
M. Armano,
H. Audley,
G. Auger,
J. Baird,
P. Binetruy,
M. Born,
D. Bortoluzzi,
N. Brandt,
A. Bursi,
M. Caleno,
A. Cavalleri,
A. Cesarini,
M. Cruise,
C. Cutler,
K. Danzmann,
I. Diepholz,
R. Dolesi,
N. Dunbar,
L. Ferraioli,
V. Ferroni,
E. Fitzsimons,
M. Freschi,
J. Gallegos,
C. Garcia. Marirrodriga,
R. Gerndt
, et al. (67 additional authors not shown)
Abstract:
The LISA Pathfinder mission will demonstrate the technology of drag-free test masses for use as inertial references in future space-based gravitational wave detectors. To accomplish this, the Pathfinder spacecraft will perform drag-free flight about a test mass while measuring the acceleration of this primary test mass relative to a second reference test mass. Because the reference test mass is co…
▽ More
The LISA Pathfinder mission will demonstrate the technology of drag-free test masses for use as inertial references in future space-based gravitational wave detectors. To accomplish this, the Pathfinder spacecraft will perform drag-free flight about a test mass while measuring the acceleration of this primary test mass relative to a second reference test mass. Because the reference test mass is contained within the same spacecraft, it is necessary to apply forces on it to maintain its position and attitude relative to the spacecraft. These forces are a potential source of acceleration noise in the LISA Pathfinder system that are not present in the full LISA configuration. While LISA Pathfinder has been designed to meet it's primary mission requirements in the presence of this noise, recent estimates suggest that the on-orbit performance may be limited by this `suspension noise'. The drift-mode or free-flight experiments provide an opportunity to mitigate this noise source and further characterize the underlying disturbances that are of interest to the designers of LISA-like instruments. This article provides a high-level overview of these experiments and the methods under development to analyze the resulting data.
△ Less
Submitted 29 December, 2014;
originally announced December 2014.
-
Searches for continuous gravitational waves from nine young supernova remnants
Authors:
J. Aasi,
B. P. Abbott,
R. Abbott,
T. Abbott,
M. R. Abernathy,
F. Acernese,
K. Ackley,
C. Adams,
T. Adams,
T. Adams,
P. Addesso,
R. X. Adhikari,
V. Adya,
C. Affeldt,
M. Agathos,
K. Agatsuma,
N. Aggarwal,
O. D. Aguiar,
A. Ain,
P. Ajith,
A. Alemic,
B. Allen,
A. Allocca,
D. Amariutei,
S. B. Anderson
, et al. (871 additional authors not shown)
Abstract:
We describe directed searches for continuous gravitational waves in data from the sixth LIGO science data run. The targets were nine young supernova remnants not associated with pulsars; eight of the remnants are associated with non-pulsing suspected neutron stars. One target's parameters are uncertain enough to warrant two searches, for a total of ten. Each search covered a broad band of frequenc…
▽ More
We describe directed searches for continuous gravitational waves in data from the sixth LIGO science data run. The targets were nine young supernova remnants not associated with pulsars; eight of the remnants are associated with non-pulsing suspected neutron stars. One target's parameters are uncertain enough to warrant two searches, for a total of ten. Each search covered a broad band of frequencies and first and second frequency derivatives for a fixed sky direction. The searches coherently integrated data from the two LIGO interferometers over time spans from 5.3-25.3 days using the matched-filtering F-statistic. We found no credible gravitational-wave signals. We set 95% confidence upper limits as strong (low) as $4\times10^{-25}$ on intrinsic strain, $2\times10^{-7}$ on fiducial ellipticity, and $3\times10^{-6}$ on r-mode amplitude. These beat the indirect limits from energy conservation and are within the range of theoretical predictions for neutron-star ellipticities and r-mode amplitudes.
△ Less
Submitted 12 August, 2021; v1 submitted 18 December, 2014;
originally announced December 2014.
-
A directed search for gravitational waves from Scorpius X-1 with initial LIGO
Authors:
The LIGO Scientific Collaboration,
the Virgo Collaboration,
J. Aasi,
B. P. Abbott,
R. Abbott,
T. Abbott,
M. R. Abernathy,
F. Acernese,
K. Ackley,
C. Adams,
T. Adams,
T. Adams,
P. Addesso,
R. X. Adhikari,
V. Adya,
C. Affeldt,
M. Agathos,
K. Agatsuma,
N. Aggarwal,
O. D. Aguiar,
A. Ain,
P. Ajith,
A. Alemic,
B. Allen,
A. Allocca
, et al. (875 additional authors not shown)
Abstract:
We present results of a search for continuously-emitted gravitational radiation, directed at the brightest low-mass X-ray binary, Scorpius X-1. Our semi-coherent analysis covers 10 days of LIGO S5 data ranging from 50-550 Hz, and performs an incoherent sum of coherent $\mathcal{F}$-statistic power distributed amongst frequency-modulated orbital sidebands. All candidates not removed at the veto sta…
▽ More
We present results of a search for continuously-emitted gravitational radiation, directed at the brightest low-mass X-ray binary, Scorpius X-1. Our semi-coherent analysis covers 10 days of LIGO S5 data ranging from 50-550 Hz, and performs an incoherent sum of coherent $\mathcal{F}$-statistic power distributed amongst frequency-modulated orbital sidebands. All candidates not removed at the veto stage were found to be consistent with noise at a 1% false alarm rate. We present Bayesian 95% confidence upper limits on gravitational-wave strain amplitude using two different prior distributions: a standard one, with no a priori assumptions about the orientation of Scorpius X-1; and an angle-restricted one, using a prior derived from electromagnetic observations. Median strain upper limits of 1.3e-24 and 8e-25 are reported at 150 Hz for the standard and angle-restricted searches respectively. This proof of principle analysis was limited to a short observation time by unknown effects of accretion on the intrinsic spin frequency of the neutron star, but improves upon previous upper limits by factors of ~1.4 for the standard, and 2.3 for the angle-restricted search at the sensitive region of the detector.
△ Less
Submitted 1 December, 2014;
originally announced December 2014.
-
Narrow-band search of continuous gravitational-wave signals from Crab and Vela pulsars in Virgo VSR4 data
Authors:
The LIGO Scientific Collaboration,
the Virgo Collaboration,
J. Aasi,
B. P. Abbott,
R. Abbott,
T. Abbott,
M. R. Abernathy,
F. Acernese,
K. Ackley,
C. Adams,
T. Adams,
T. Adams,
P. Addesso,
R. X. Adhikari,
V. Adya,
C. Affeldt,
M. Agathos,
K. Agatsuma,
N. Aggarwal,
O. D. Aguiar,
A. Ain,
P. Ajith,
A. Alemic,
B. Allen,
A. Allocca
, et al. (878 additional authors not shown)
Abstract:
In this paper we present the results of a coherent narrow-band search for continuous gravitational-wave signals from the Crab and Vela pulsars conducted on Virgo VSR4 data. In order to take into account a possible small mismatch between the gravitational wave frequency and two times the star rotation frequency, inferred from measurement of the electromagnetic pulse rate, a range of 0.02 Hz around…
▽ More
In this paper we present the results of a coherent narrow-band search for continuous gravitational-wave signals from the Crab and Vela pulsars conducted on Virgo VSR4 data. In order to take into account a possible small mismatch between the gravitational wave frequency and two times the star rotation frequency, inferred from measurement of the electromagnetic pulse rate, a range of 0.02 Hz around two times the star rotational frequency has been searched for both the pulsars. No evidence for a signal has been found and 95$\%$ confidence level upper limits have been computed both assuming polarization parameters are completely unknown and that they are known with some uncertainty, as derived from X-ray observations of the pulsar wind torii. For Vela the upper limits are comparable to the spin-down limit, computed assuming that all the observed spin-down is due to the emission of gravitational waves. For Crab the upper limits are about a factor of two below the spin-down limit, and represent a significant improvement with respect to past analysis. This is the first time the spin-down limit is significantly overcome in a narrow-band search.
△ Less
Submitted 30 October, 2014;
originally announced October 2014.
-
Descope of the ALIA mission
Authors:
Xuefei Gong,
Yun-Kau Lau,
Shengnian Xu,
Pau Amaro-Seoane,
Shan Bai,
Xing Bian,
Zhoujian Cao,
Gerui Chen,
Xian Chen,
Yanwei Ding,
Peng Dong,
Wei Gao,
Gerhard Heinzel,
Ming Li,
Shuo Li,
Fukun Liu,
Ziren Luo,
Mingxue Shao,
Rainer Spurzem,
Baosan Sun,
Wenlin Tang,
Yan Wang,
Peng Xu,
Pin Yu,
Yefei Yuan
, et al. (2 additional authors not shown)
Abstract:
The present work reports on a feasibility study commissioned by the Chinese Academy of Sciences of China to explore various possible mission options to detect gravitational waves in space alternative to that of the eLISA/LISA mission concept. Based on the relative merits assigned to science and technological viability, a few representative mission options descoped from the ALIA mission are conside…
▽ More
The present work reports on a feasibility study commissioned by the Chinese Academy of Sciences of China to explore various possible mission options to detect gravitational waves in space alternative to that of the eLISA/LISA mission concept. Based on the relative merits assigned to science and technological viability, a few representative mission options descoped from the ALIA mission are considered. A semi-analytic Monte Carlo simulation is carried out to understand the cosmic black hole merger histories starting from intermediate mass black holes at high redshift as well as the possible scientific merits of the mission options considered in probing the light seed black holes and their coevolution with galaxies in early Universe. The study indicates that, by choosing the armlength of the interferometer to be three million kilometers and shifting the sensitivity floor to around one-hundredth Hz, together with a very moderate improvement on the position noise budget, there are certain mission options capable of exploring light seed, intermediate mass black hole binaries at high redshift that are not readily accessible to eLISA/LISA, and yet the technological requirements seem to within reach in the next few decades for China.
△ Less
Submitted 28 November, 2014; v1 submitted 22 October, 2014;
originally announced October 2014.
-
Thermo-elastic induced phase noise in the LISA Pathfinder spacecraft
Authors:
Ferran Gibert,
Miquel Nofrarias,
Nikolaos Karnesis,
Lluís Gesa,
Víctor Martín,
Ignacio Mateos,
Alberto Lobo,
Reinhold Flatscher,
Domenico Gerardi,
Johannes Burkhardt,
Ruediger Gerndt,
David Robertson,
Henry Ward,
Paul William McNamara,
Felipe Guzmán,
Martin Hewitson,
Ingo Diepholz,
Jens Reiche,
Gerhard Heinzel,
Karsten Danzmann
Abstract:
During the On-Station Thermal Test campaign of the LISA Pathfinder the data and diagnostics subsystem was tested in nearly space conditions for the first time after integration in the satellite. The results showed the compliance of the temperature measurement system, obtaining temperature noise around $10^{-4}\,{\rm K}\, {\rm Hz}^{-1/2}$ in the frequency band of $1-30\;{\rm mHz}$. In addition, con…
▽ More
During the On-Station Thermal Test campaign of the LISA Pathfinder the data and diagnostics subsystem was tested in nearly space conditions for the first time after integration in the satellite. The results showed the compliance of the temperature measurement system, obtaining temperature noise around $10^{-4}\,{\rm K}\, {\rm Hz}^{-1/2}$ in the frequency band of $1-30\;{\rm mHz}$. In addition, controlled injection of heat signals to the suspension struts anchoring the LISA Technology Package (LTP) Core Assembly to the satellite structure allowed to experimentally estimate for the first time the phase noise contribution through thermo-elastic distortion of the LTP interferometer, the satellite's main instrument. Such contribution was found to be at $10^{-12}\,{\rm m}\, {\rm Hz}^{-1/2}$, a factor of 30 below the measured noise at the lower end of the measurement bandwidth ($1\,{\rm mHz}$).
△ Less
Submitted 12 December, 2014; v1 submitted 18 May, 2014;
originally announced May 2014.
-
First stage of LISA data processing: Clock synchronization and arm-length determination via a hybrid-extended Kalman filter
Authors:
Yan Wang,
Gerhard Heinzel,
Karsten Danzmann
Abstract:
In this paper, we describe a hybrid-extended Kalman filter algorithm to synchronize the clocks and to precisely determine the inter-spacecraft distances for space-based gravitational wave detectors, such as (e)LISA. According to the simulation, the algorithm has significantly improved the ranging accuracy and synchronized the clocks, making the phase-meter raw measurements qualified for time- dela…
▽ More
In this paper, we describe a hybrid-extended Kalman filter algorithm to synchronize the clocks and to precisely determine the inter-spacecraft distances for space-based gravitational wave detectors, such as (e)LISA. According to the simulation, the algorithm has significantly improved the ranging accuracy and synchronized the clocks, making the phase-meter raw measurements qualified for time- delay interferometry algorithms.
△ Less
Submitted 10 September, 2014; v1 submitted 25 February, 2014;
originally announced February 2014.
-
Phasemeter core for intersatellite laser heterodyne interferometry: modelling, simulations and experiments
Authors:
Oliver Gerberding,
Benjamin Sheard,
Iouri Bykov,
Joachim Kullmann,
Juan Jose Esteban Delgado,
Karsten Danzmann,
Gerhard Heinzel
Abstract:
Inter satellite laser interferometry is a central component of future space-borne gravity instruments like LISA, eLISA, NGO and future geodesy missions. The inherently small laser wavelength allows to measure distance variations with extremely high precision by interfering a reference beam with a measurement beam. The readout of such interferometers is often based on tracking phasemeters, able to…
▽ More
Inter satellite laser interferometry is a central component of future space-borne gravity instruments like LISA, eLISA, NGO and future geodesy missions. The inherently small laser wavelength allows to measure distance variations with extremely high precision by interfering a reference beam with a measurement beam. The readout of such interferometers is often based on tracking phasemeters, able to measure the phase of an incoming beatnote with high precision over a wide range of frequencies. The implementation of such phasemeters is based on all digital phase-locked loops, hosted in FPGAs. Here we present a precise model of an all digital phase locked loop that allows to design such a readout algorithm and we support our analysis by numerical performance measurements and experiments with analog signals.
△ Less
Submitted 9 October, 2013;
originally announced October 2013.
-
State space modelling and data analysis exercises in LISA Pathfinder
Authors:
M Nofrarias,
F Antonucci,
M Armano,
H Audley,
G Auger,
M Benedetti,
P Binetruy,
J Bogenstahl,
D Bortoluzzi,
N Brandt,
M Caleno,
A Cavalleri,
G Congedo,
M Cruise,
K Danzmann,
F De Marchi,
M Diaz-Aguilo,
I Diepholz,
G Dixon,
R Dolesi,
N Dunbar,
J Fauste,
L Ferraioli,
V Ferroni W Fichter,
E Fitzsimons
, et al. (61 additional authors not shown)
Abstract:
LISA Pathfinder is a mission planned by the European Space Agency to test the key technologies that will allow the detection of gravitational waves in space. The instrument on-board, the LISA Technology package, will undergo an exhaustive campaign of calibrations and noise characterisation campaigns in order to fully describe the noise model. Data analysis plays an important role in the mission an…
▽ More
LISA Pathfinder is a mission planned by the European Space Agency to test the key technologies that will allow the detection of gravitational waves in space. The instrument on-board, the LISA Technology package, will undergo an exhaustive campaign of calibrations and noise characterisation campaigns in order to fully describe the noise model. Data analysis plays an important role in the mission and for that reason the data analysis team has been developing a toolbox which contains all the functionalities required during operations. In this contribution we give an overview of recent activities, focusing on the improvements in the modelling of the instrument and in the data analysis campaigns performed both with real and simulated data.
△ Less
Submitted 21 June, 2013; v1 submitted 19 June, 2013;
originally announced June 2013.
-
The Gravitational Universe
Authors:
The eLISA Consortium,
:,
P. Amaro Seoane,
S. Aoudia,
H. Audley,
G. Auger,
S. Babak,
J. Baker,
E. Barausse,
S. Barke,
M. Bassan,
V. Beckmann,
M. Benacquista,
P. L. Bender,
E. Berti,
P. Binétruy,
J. Bogenstahl,
C. Bonvin,
D. Bortoluzzi,
N. C. Brause,
J. Brossard,
S. Buchman,
I. Bykov,
J. Camp,
C. Caprini
, et al. (136 additional authors not shown)
Abstract:
The last century has seen enormous progress in our understanding of the Universe. We know the life cycles of stars, the structure of galaxies, the remnants of the big bang, and have a general understanding of how the Universe evolved. We have come remarkably far using electromagnetic radiation as our tool for observing the Universe. However, gravity is the engine behind many of the processes in th…
▽ More
The last century has seen enormous progress in our understanding of the Universe. We know the life cycles of stars, the structure of galaxies, the remnants of the big bang, and have a general understanding of how the Universe evolved. We have come remarkably far using electromagnetic radiation as our tool for observing the Universe. However, gravity is the engine behind many of the processes in the Universe, and much of its action is dark. Opening a gravitational window on the Universe will let us go further than any alternative. Gravity has its own messenger: Gravitational waves, ripples in the fabric of spacetime. They travel essentially undisturbed and let us peer deep into the formation of the first seed black holes, exploring redshifts as large as z ~ 20, prior to the epoch of cosmic re-ionisation. Exquisite and unprecedented measurements of black hole masses and spins will make it possible to trace the history of black holes across all stages of galaxy evolution, and at the same time constrain any deviation from the Kerr metric of General Relativity. eLISA will be the first ever mission to study the entire Universe with gravitational waves. eLISA is an all-sky monitor and will offer a wide view of a dynamic cosmos using gravitational waves as new and unique messengers to unveil The Gravitational Universe. It provides the closest ever view of the early processes at TeV energies, has guaranteed sources in the form of verification binaries in the Milky Way, and can probe the entire Universe, from its smallest scales around singularities and black holes, all the way to cosmological dimensions.
△ Less
Submitted 24 May, 2013;
originally announced May 2013.
-
Subtraction of temperature induced phase noise in the LISA frequency band
Authors:
M. Nofrarias,
F. Gibert,
N. Karnesis,
A. F. Garcia,
M. Hewitson,
G. Heinzel,
K. Danzmann
Abstract:
Temperature fluctuations are expected to be one of the limiting factors for gravitational wave detectors in the very low frequency range. Here we report the characterisation of this noise source in the LISA Pathfinder optical bench and propose a method to remove its contribution from the data. Our results show that temperature fluctuations are indeed limiting our measurement below one millihertz,…
▽ More
Temperature fluctuations are expected to be one of the limiting factors for gravitational wave detectors in the very low frequency range. Here we report the characterisation of this noise source in the LISA Pathfinder optical bench and propose a method to remove its contribution from the data. Our results show that temperature fluctuations are indeed limiting our measurement below one millihertz, and that their subtraction leads to a factor 5.6 (15 dB) reduction in the noise level at the lower end of the LISA measurement band 10^{-4} Hz, which increases to 20.2 (26 dB) at even lower frequencies, i.e., 1.5x10^{-5} Hz. The method presented here can be applied to the subtraction of other noise sources in gravitational wave detectors in the general situation where multiple sensors are used to characterise the noise source.
△ Less
Submitted 19 June, 2013; v1 submitted 22 February, 2013;
originally announced February 2013.
-
Breadboard model of the LISA phasemeter
Authors:
Oliver Gerberding,
Simon Barke,
Ioury Bykov,
Karsten Danzmann,
Anders Enggaard,
Juan Jose Esteban,
Alberto Gianolio,
Torben Vendt Hansen,
Gerhard Heinzel,
Allan Hornstrup,
Oliver Jennrich,
Joachim Kullmann,
Søren Møller Pedersen,
Torben Rasmussen,
Jens Reiche,
Zoran Sodnik,
Martin Suess
Abstract:
An elegant breadboard model of the LISA phasemeter is currently under development by a Danish-German consortium. The breadboard is build in the frame of an ESA technology development activity to demonstrate the feasibility and readiness of the LISA metrology baseline architecture. This article gives an overview about the breadboard design and its components, including the distribution of key funct…
▽ More
An elegant breadboard model of the LISA phasemeter is currently under development by a Danish-German consortium. The breadboard is build in the frame of an ESA technology development activity to demonstrate the feasibility and readiness of the LISA metrology baseline architecture. This article gives an overview about the breadboard design and its components, including the distribution of key functionalities.
△ Less
Submitted 27 January, 2013; v1 submitted 31 August, 2012;
originally announced August 2012.
-
The end-to-end testbed of the Optical Metrology System on-board LISA Pathfinder
Authors:
Frank Steier,
Felipe Guzmán Cervantes,
Antonio F. García Marín,
Domenico Gerardi,
Gerhard Heinzel,
Karsten Danzmann
Abstract:
LISA Pathfinder is a technology demonstration mission for the Laser Interferometer Space Antenna (LISA). The main experiment on-board LISA Pathfinder is the so-called LISA Technology Package (LTP) which has the aim to measure the differential acceleration between two free-falling test masses with an accuracy of 3x10^(-14) ms^(-2)/sqrt[Hz] between 1 mHz and 30 mHz. This measurement is performed int…
▽ More
LISA Pathfinder is a technology demonstration mission for the Laser Interferometer Space Antenna (LISA). The main experiment on-board LISA Pathfinder is the so-called LISA Technology Package (LTP) which has the aim to measure the differential acceleration between two free-falling test masses with an accuracy of 3x10^(-14) ms^(-2)/sqrt[Hz] between 1 mHz and 30 mHz. This measurement is performed interferometrically by the Optical Metrology System (OMS) on-board LISA Pathfinder. In this paper we present the development of an experimental end-to-end testbed of the entire OMS. It includes the interferometer and its sub-units, the interferometer back-end which is a phasemeter and the processing of the phasemeter output data. Furthermore, 3-axes piezo actuated mirrors are used instead of the free-falling test masses for the characterisation of the dynamic behaviour of the system and some parts of the Drag-free and Attitude Control System (DFACS) which controls the test masses and the satellite. The end-to-end testbed includes all parts of the LTP that can reasonably be tested on earth without free-falling test masses. At its present status it consists mainly of breadboard components. Some of those have already been replaced by Engineering Models of the LTP experiment. In the next steps, further Engineering Models and Flight Models will also be inserted in this testbed and tested against well characterised breadboard components. The presented testbed is an important reference for the unit tests and can also be used for validation of the on-board experiment during the mission.
△ Less
Submitted 21 March, 2012;
originally announced March 2012.
-
Real-time phasefront detector for heterodyne interferometers
Authors:
Felipe Guzmán Cervantes,
Gerhard Heinzel,
Antonio F. García Marín,
Vinzenz Wand,
Frank Steier,
Oliver Jennrich,
Karsten Danzmann
Abstract:
We present a real-time differential phasefront detector sensitive to better than 3 mrad rms, which corresponds to a precision of about 500 pm. This detector performs a spatially resolving measurement of the phasefront of a heterodyne interferometer, with heterodyne frequencies up to approximately 10 kHz. This instrument was developed as part of the research for the LISA Technology Package (LTP) in…
▽ More
We present a real-time differential phasefront detector sensitive to better than 3 mrad rms, which corresponds to a precision of about 500 pm. This detector performs a spatially resolving measurement of the phasefront of a heterodyne interferometer, with heterodyne frequencies up to approximately 10 kHz. This instrument was developed as part of the research for the LISA Technology Package (LTP) interferometer, and will assist in the manufacture of its flight model. Due to the advantages this instrument offers, it also has general applications in optical metrology.
△ Less
Submitted 20 March, 2012;
originally announced March 2012.
-
Subtraction of test mass angular noise in the LISA Technology Package interferometer
Authors:
Felipe Guzmán Cervantes,
Frank Steier,
Gudrun Wanner,
Gerhard Heinzel,
Karsten Danzmann
Abstract:
We present recent sensitivity measurements of the LISA Technology Package interferometer with articulated mirrors as test masses, actuated by piezo-electric transducers. The required longitudinal displacement resolution of 9 pm/sqrt[Hz] above 3 mHz has been demonstrated with an angular noise that corresponds to the expected in on-orbit operation. The excess noise contribution of this test mass jit…
▽ More
We present recent sensitivity measurements of the LISA Technology Package interferometer with articulated mirrors as test masses, actuated by piezo-electric transducers. The required longitudinal displacement resolution of 9 pm/sqrt[Hz] above 3 mHz has been demonstrated with an angular noise that corresponds to the expected in on-orbit operation. The excess noise contribution of this test mass jitter onto the sensitive displacement readout was completely subtracted by fitting the angular interferometric data streams to the longitudinal displacement measurement. Thus, this cross-coupling constitutes no limitation to the required performance of the LISA Technology Package interferometry.
△ Less
Submitted 20 March, 2012;
originally announced March 2012.
-
Deep phase modulation interferometry
Authors:
Gerhard Heinzel,
Felipe Guzmán Cervantes,
Antonio F. García Marín,
Joachim Kullmann,
Wang Feng,
Karsten Danzmann
Abstract:
We have developed a method to equip homodyne interferometers with the capability to operate with constant high sensitivity over many fringes for continuous real-time tracking. The method can be considered as an extension of the "J_1...J_4" methods, and its enhancement to deliver very sensitive angular measurements through Differential Wavefront Sensing is straightforward. Beam generation requires…
▽ More
We have developed a method to equip homodyne interferometers with the capability to operate with constant high sensitivity over many fringes for continuous real-time tracking. The method can be considered as an extension of the "J_1...J_4" methods, and its enhancement to deliver very sensitive angular measurements through Differential Wavefront Sensing is straightforward. Beam generation requires a sinusoidal phase modulation of several radians in one interferometer arm. On a stable optical bench, we have demonstrated a long-term sensitivity over thousands of seconds of 0.1 mrad/sqrt[Hz] that correspond to 20 pm/sqrt[Hz] in length, and 10 nrad/sqrt[Hz] in angle at millihertz frequencies.
△ Less
Submitted 21 March, 2012; v1 submitted 13 March, 2012;
originally announced March 2012.
-
From laboratory experiments to LISA Pathfinder: achieving LISA geodesic motion
Authors:
F Antonucci,
M Armano,
H Audley,
G Auger,
M Benedetti,
P Binetruy,
C Boatella,
J Bogenstahl,
D Bortoluzzi,
P Bosetti,
N Brandt,
M Caleno,
A Cavalleri,
M Cesa,
M Chmeissani,
G Ciani,
A Conchillo,
G Congedo,
I Cristofolini,
M Cruise,
K Danzmann,
F De Marchi,
M Diaz-Aguilo,
I Diepholz,
G Dixon
, et al. (76 additional authors not shown)
Abstract:
This paper presents a quantitative assessment of the performance of the upcoming LISA Pathfinder geodesic explorer mission. The findings are based on the results of extensive ground testing and simulation campaigns using flight hardware and flight control and operations algorithms. The results show that, for the central experiment of measuring the stray differential acceleration between the LISA t…
▽ More
This paper presents a quantitative assessment of the performance of the upcoming LISA Pathfinder geodesic explorer mission. The findings are based on the results of extensive ground testing and simulation campaigns using flight hardware and flight control and operations algorithms. The results show that, for the central experiment of measuring the stray differential acceleration between the LISA test masses, LISA Pathfinder will be able to verify the overall acceleration noise to within a factor two of the LISA requirement at 1 mHz and within a factor 6 at 0.1 mHz. We also discuss the key elements of the physical model of disturbances, coming from LISA Pathfinder and ground measurement, that will guarantee the LISA performance.
△ Less
Submitted 20 January, 2011; v1 submitted 29 December, 2010;
originally announced December 2010.
-
Bayesian parameter estimation in the second LISA Pathfinder Mock Data Challenge
Authors:
M. Nofrarias,
C. Röver,
M. Hewitson,
A. Monsky,
G. Heinzel,
K. Danzmann,
L. Ferraioli,
M. Hueller,
S. Vitale
Abstract:
A main scientific output of the LISA Pathfinder mission is to provide a noise model that can be extended to the future gravitational wave observatory, LISA. The success of the mission depends thus upon a deep understanding of the instrument, especially the ability to correctly determine the parameters of the underlying noise model. In this work we estimate the parameters of a simplified model of t…
▽ More
A main scientific output of the LISA Pathfinder mission is to provide a noise model that can be extended to the future gravitational wave observatory, LISA. The success of the mission depends thus upon a deep understanding of the instrument, especially the ability to correctly determine the parameters of the underlying noise model. In this work we estimate the parameters of a simplified model of the LISA Technology Package (LTP) instrument. We describe the LTP by means of a closed-loop model that is used to generate the data, both injected signals and noise. Then, parameters are estimated using a Bayesian framework and it is shown that this method reaches the optimal attainable error, the Cramer-Rao bound. We also address an important issue for the mission: how to efficiently combine the results of different experiments to obtain a unique set of parameters describing the instrument.
△ Less
Submitted 31 August, 2010;
originally announced August 2010.
-
Calibrating spectral estimation for the LISA Technology Package with multichannel synthetic noise generation
Authors:
Luigi Ferraioli,
Gerhard Heinzel,
Martin Hewitson,
Mauro Hueller,
Anneke Monsky,
Miquel Nofrarias,
Stefano Vitale
Abstract:
The scientific objectives of the Lisa Technology Package (LTP) experiment, on board of the LISA Pathfinder mission, demand for an accurate calibration and validation of the data analysis tools in advance of the mission launch. The levels of confidence required on the mission outcomes can be reached only with an intense activity on synthetically generated data. A flexible procedure allowing the gen…
▽ More
The scientific objectives of the Lisa Technology Package (LTP) experiment, on board of the LISA Pathfinder mission, demand for an accurate calibration and validation of the data analysis tools in advance of the mission launch. The levels of confidence required on the mission outcomes can be reached only with an intense activity on synthetically generated data. A flexible procedure allowing the generation of cross-correlated stationary noise time series was set-up. Multi-channel time series with the desired cross correlation behavior can be generated once a model for a multichannel cross-spectral matrix is provided. The core of the procedure is the synthesis of a noise coloring multichannel filter through a frequency-by-frequency eigendecomposition of the model cross-spectral matrix and a Z-domain fit. The common problem of initial transients in noise time series is solved with a proper initialization of the filter recursive equations. The noise generator performances were tested in a two dimensional case study of the LTP dynamics along the two principal channels of the sensing interferometer.
△ Less
Submitted 15 July, 2010; v1 submitted 1 June, 2010;
originally announced June 2010.
-
Thermal diagnostic of the Optical Window on board LISA Pathfinder
Authors:
M. Nofrarias,
A. F. Garcia Marin,
A. Lobo,
G. Heinzel,
J. Ramos-Castro,
J. Sanjuan,
K. Danzmann
Abstract:
Vacuum conditions inside the LTP Gravitational Reference Sensor must comply with rather demanding requirements. The Optical Window (OW) is an interface which seals the vacuum enclosure and, at the same time, lets the laser beam go through for interferometric Metrology with the test masses. The OW is a plane-parallel plate clamped in a Titanium flange, and is considerably sensitive to thermal and…
▽ More
Vacuum conditions inside the LTP Gravitational Reference Sensor must comply with rather demanding requirements. The Optical Window (OW) is an interface which seals the vacuum enclosure and, at the same time, lets the laser beam go through for interferometric Metrology with the test masses. The OW is a plane-parallel plate clamped in a Titanium flange, and is considerably sensitive to thermal and stress fluctuations. It is critical for the required precision measurements, hence its temperature will be carefully monitored in flight. This paper reports on the results of a series of OW characterisation laboratory runs, intended to study its response to selected thermal signals, as well as their fit to numerical models, and the meaning of the latter. We find that a single pole ARMA transfer function provides a consistent approximation to the OW response to thermal excitations, and derive a relationship with the physical processes taking place in the OW. We also show how system noise reduction can be accomplished by means of that transfer function.
△ Less
Submitted 4 September, 2007;
originally announced September 2007.
-
Frequency domain interferometer simulation with higher-order spatial modes
Authors:
A. Freise,
G. Heinzel,
H. Lueck,
R. Schilling,
B. Willke,
K. Danzmann
Abstract:
FINESSE is a software simulation that allows to compute the optical properties of laser interferometers as they are used by the interferometric gravitational-wave detectors today. It provides a fast and versatile tool which has proven to be very useful during the design and the commissioning of gravitational-wave detectors. The basic algorithm of FINESSE numerically computes the light amplitudes…
▽ More
FINESSE is a software simulation that allows to compute the optical properties of laser interferometers as they are used by the interferometric gravitational-wave detectors today. It provides a fast and versatile tool which has proven to be very useful during the design and the commissioning of gravitational-wave detectors. The basic algorithm of FINESSE numerically computes the light amplitudes inside an interferometer using Hermite-Gauss modes in the frequency domain. In addition, FINESSE provides a number of commands to easily generate and plot the most common signals like, for example, power enhancement, error or control signals, transfer functions and shot-noise-limited sensitivities.
Among the various simulation tools available to the gravitational wave community today, FINESSE is the most advanced general optical simulation that uses the frequency domain. It has been designed to allow general analysis of user defined optical setups while being easy to install and easy to use.
△ Less
Submitted 13 January, 2004; v1 submitted 2 September, 2003;
originally announced September 2003.
-
Performance of a 1200m long suspended Fabry-Perot cavity
Authors:
A. Freise,
M. M. Casey,
S. Gossler,
H. Grote,
G. Heinzel,
H. Lueck,
D. I. Robertson,
K. A. Strain,
H. Ward,
B. Willke,
J. Hough,
K. Danzmann
Abstract:
Using one arm of the Michelson interferometer and the power recycling mirror of the interferometric gravitational wave detector GEO600, we created a Fabry-Perot cavity with a length of 1200 m. The main purpose of this experiment was to gather first experience with the main optics, its suspensions and the corresponding control systems. The residual displacement of a main mirror is about 150 nm rm…
▽ More
Using one arm of the Michelson interferometer and the power recycling mirror of the interferometric gravitational wave detector GEO600, we created a Fabry-Perot cavity with a length of 1200 m. The main purpose of this experiment was to gather first experience with the main optics, its suspensions and the corresponding control systems. The residual displacement of a main mirror is about 150 nm rms. By stabilising the length of the 1200 m long cavity to the pre-stabilised laser beam we achieved an error point frequency noise of 0.1 mHz/sqrt(Hz) at 100 Hz Fourier frequency. In addition we demonstrated the reliable performance of all included subsystems by several 10-hour-periods of continuous stable operation. Thus the full frequency stabilisation scheme for GEO600 was successfully tested.
△ Less
Submitted 5 November, 2001; v1 submitted 2 October, 2001;
originally announced October 2001.
-
Demonstration of detuned dual recycling at the Garching 30m laser interferometer
Authors:
A. Freise,
G. Heinzel,
K. A. Strain,
J. Mizuno,
K. D. Skeldon,
H. Lueck,
B. Willke,
R. Schilling,
A. Ruediger,
W. Winkler,
K. Danzmann
Abstract:
Dual recycling is an advanced optical technique to enhance the signal-to-noise ratio of laser interferometric gravitational wave detectors in a limited bandwidth. To optimise the center of this band with respect to Fourier frequencies of expected gravitational wave signals detuned dual recycling has to be implemented. We demonstrated detuned dual recycling on a fully suspended 30m prototype inte…
▽ More
Dual recycling is an advanced optical technique to enhance the signal-to-noise ratio of laser interferometric gravitational wave detectors in a limited bandwidth. To optimise the center of this band with respect to Fourier frequencies of expected gravitational wave signals detuned dual recycling has to be implemented. We demonstrated detuned dual recycling on a fully suspended 30m prototype interferometer. A control scheme that allows to tune the detector to different frequencies will be outlined. Good agreement between the experimental results and numerical simulations has been achieved.
△ Less
Submitted 19 October, 2000; v1 submitted 7 June, 2000;
originally announced June 2000.