-
Flexible fast-convolution processing for cellular radio evolution
Authors:
Juha Yli-Kaakinen,
Toni Levanen,
Arto Palin,
Markku Renfors,
Mikko Valkama
Abstract:
Orthogonal frequency-division multiplexing (OFDM) has been selected as a baseline waveform for long-term evolution (LTE) and fifth-generation new radio (5G NR). Fast-convolution (FC)-based frequency-domain signal processing has been considered recently as an effective tool for spectrum enhancement of OFDM-based waveforms. FC-based filtering approximates linear convolution by effective fast Fourier…
▽ More
Orthogonal frequency-division multiplexing (OFDM) has been selected as a baseline waveform for long-term evolution (LTE) and fifth-generation new radio (5G NR). Fast-convolution (FC)-based frequency-domain signal processing has been considered recently as an effective tool for spectrum enhancement of OFDM-based waveforms. FC-based filtering approximates linear convolution by effective fast Fourier transform (FFT)-based circular convolutions using partly overlapping processing blocks. In earlier work, we have shown that FC-based filtering is a very flexible and efficient tool for filtered-OFDM signal generation and receiver side subband filtering. In this paper, we present a symbol-synchronous FC-processing scheme flexibly allowing filter re-configuration time resolution equal to one OFDM symbol while supporting tight carrier-wise filtering for 5G NR in mixed-numerology scenarios with adjustable subcarrier spacings, center frequencies, and subband bandwidths as well as providing co-exitence with LTE. The proposed scheme is demonstrated to support envisioned use cases of 5G NR and provide flexible starting point for sixth generation development.
△ Less
Submitted 5 February, 2022;
originally announced February 2022.
-
Phase Noise Resilient Three-Level Continuous-Phase Modulation for DFT-Spread OFDM
Authors:
Markku Renfors,
Ismael Peruga Nasarre,
Toni Levanen,
Mikko Valkama,
Kari Pajukoski
Abstract:
A novel OFDM-based waveform with low peak-to-average power ratio (PAPR) and high robustness against phase noise (PN) is presented. It follows the discrete Fourier transform spread orthogonal frequency division multiplexing (DFT-s-OFDM) signal model. 3MSK, is inspired by continuous-phase frequency shift keying (FSK), but it uses three frequencies in the baseband model -- specifically, 0 and…
▽ More
A novel OFDM-based waveform with low peak-to-average power ratio (PAPR) and high robustness against phase noise (PN) is presented. It follows the discrete Fourier transform spread orthogonal frequency division multiplexing (DFT-s-OFDM) signal model. 3MSK, is inspired by continuous-phase frequency shift keying (FSK), but it uses three frequencies in the baseband model -- specifically, 0 and $\pm f_{symbol}/4$, where $f_{symbol}$ is the symbol rate -- which effectively constrains the phase transitions between consecutive symbols to 0 and $\pm π/2$ rad. Motivated by the phase controlled model of modulation, different degrees of phase continuity can be achieved, while supporting receiver processing with low complexity. The signal characteristics are improved by generating an initial time-domain nearly constant envelope signal at higher than the symbol rate. This helps to reach smooth phase transitions between 3MSK symbols. Also the possibility of using excess bandwidth is investigated by transmitting additional non-zero subcarriers outside active subcarriers of the basic DFT-s-OFDM model, which provides the capability to greatly reduce the PAPR. Due to the fact that the information is encoded in the phase transitions, a receiver model that tracks the phase variations without needing reference signals is developed. To this end, it is shown that this new modulation is well-suited for non-coherent receivers, even under strong phase noise (PN) conditions, thus allowing to reduce the overhead of reference signals. Evaluations of this physical-layer modulation and waveform scheme are performed in terms of transmitter metrics such as PAPR, OOB emissions and achievable output power after the power amplifier (PA). Finally, coded radio link evaluations are also shown and provided, demonstrating that 3MSK has a similar BER performance as that of traditional QPSK.
△ Less
Submitted 12 October, 2021;
originally announced October 2021.
-
Joint Positioning and Tracking via NR Sidelink in 5G-Empowered Industrial IoT: Releasing the Potential of V2X Technology
Authors:
Yi Lu,
Mike Koivisto,
Jukka Talvitie,
Elizaveta Rastorgueva-Foi,
Toni Levanen,
Elena Simona Lohan,
Mikko Valkama
Abstract:
The fifth generation (5G) mobile networks with enhanced connectivity and positioning capabilities play an increasingly important role in the development of automated vehicle-to-everything (V2X) and other advanced industrial Internet of Things (IoT) systems. In this article, we address the prospects of 5G New Radio (NR) sidelink based V2X networks and their applicability for increasing the situatio…
▽ More
The fifth generation (5G) mobile networks with enhanced connectivity and positioning capabilities play an increasingly important role in the development of automated vehicle-to-everything (V2X) and other advanced industrial Internet of Things (IoT) systems. In this article, we address the prospects of 5G New Radio (NR) sidelink based V2X networks and their applicability for increasing the situational awareness, in terms of continuous tracking of moving connected machines and vehicles, in industrial systems. For increased system flexibility and fast deployments, we assume that the locations of the so-called anchor nodes are unknown, and describe an extended Kalman filter-based joint positioning and tracking framework in which the locations of both the anchor nodes and the target nodes can be estimated simultaneously. We assess and demonstrate the achievable 3D positioning and tracking performance in the context of a realistic industrial warehouse facility, through extensive ray-tracing based evaluations at the 26 GHz NR band. Our findings show that when both angle-based and time-based measurements are utilized, reaching sub-1 meter accuracy is realistic and that the system is also relatively robust against different node geometries. Finally, several research challenges towards achieving robust, high-performance and cost-efficient positioning solutions are outlined and discussed, identifying various potential directions for future work.
△ Less
Submitted 3 June, 2021; v1 submitted 15 January, 2021;
originally announced January 2021.
-
Frequency-Domain Signal Processing for Spectrally-Enhanced CP-OFDM Waveforms in 5G New Radio
Authors:
Juha Yli-Kaakinen,
AlaaEddin Loulou,
Toni Levanen,
Kari Pajukoski,
Arto Palin,
Markku Renfors,
Mikko Valkama
Abstract:
Orthogonal frequency-division multiplexing (OFDM) has been selected as the basis for the fifth-generation new radio (5G-NR) waveform developments. However, effective signal processing tools are needed for enhancing the OFDM spectrum in various advanced transmission scenarios. In earlier work, we have shown that fast-convolution (FC) processing is a very flexible and efficient tool for filtered-OFD…
▽ More
Orthogonal frequency-division multiplexing (OFDM) has been selected as the basis for the fifth-generation new radio (5G-NR) waveform developments. However, effective signal processing tools are needed for enhancing the OFDM spectrum in various advanced transmission scenarios. In earlier work, we have shown that fast-convolution (FC) processing is a very flexible and efficient tool for filtered-OFDM signal generation and receiver-side subband filtering, e.g., for the mixed-numerology scenarios of the 5G-NR. FC filtering approximates linear convolution through effective fast Fourier transform (FFT)-based circular convolutions using partly overlapping processing blocks. However, with the continuous overlap-and-save and overlap-and-add processing models with fixed block-size and fixed overlap, the FC-processing blocks cannot be aligned with all OFDM symbols of a transmission frame. Furthermore, 5G-NR numerology does not allow to use transform lengths shorter than 128 because this would lead to non-integer cyclic prefix (CP) lengths. In this article, we present new FC-processing schemes which solve the mentioned limitations. These schemes are based on dynamically adjusting the overlap periods and extrapolating the CP samples, which make it possible to align the FC blocks with each OFDM symbol, even in case of variable CP lengths. This reduces complexity and latency, e.g., in mini-slot transmissions and, as an example, allows to use 16-point transforms in case of a 12-subcarrier-wide subband allocation, greatly reducing the implementation complexity. On the receiver side, the proposed scheme makes it possible to effectively combine cascaded inverse and forward FFT units in FC-filtered OFDM processing. Transform decomposition is used to simplify these computations. Very extensive set of numerical results is also provided, in terms of radio-link performance and associated processing complexity.
△ Less
Submitted 3 August, 2020;
originally announced August 2020.
-
5G New Radio Evolution Towards Sub-THz Communications
Authors:
Oskari Tervo,
Toni Levanen,
Kari Pajukoski,
Jari Hulkkonen,
Pekka Wainio,
Mikko Valkama
Abstract:
In this paper, the potential of extending 5G New Radio physical layer solutions to support communications in sub-THz frequencies is studied. More specifically, we introduce the status of third generation partnership project studies related to operation on frequencies beyond 52.6 GHz and note also the recent proposal on spectrum horizons provided by federal communications commission (FCC) related t…
▽ More
In this paper, the potential of extending 5G New Radio physical layer solutions to support communications in sub-THz frequencies is studied. More specifically, we introduce the status of third generation partnership project studies related to operation on frequencies beyond 52.6 GHz and note also the recent proposal on spectrum horizons provided by federal communications commission (FCC) related to experimental licenses on 95 GHz - 3 THz frequency band. Then, we review the power amplifier (PA) efficiency and output power challenge together with the increased phase noise (PN) distortion effect in terms of the supported waveforms. As a practical example on the waveform and numerology design from the perspective of the PN robustness, link performance results using 90 GHz carrier frequency are provided. The numerical results demonstrate that new, higher subcarrier spacings are required to support high throughput, which requires larger changes in the physical layer design. It is also observed that new phase-tracking reference signal designs are required to make the system robust against PN. The results illustrate that single-carrier frequency division multiple access is significantly more robust against PN and can provide clearly larger PA output power than cyclic-prefix orthogonal frequency division multiplexing, and is therefore a highly potential waveform for sub-THz communications.
△ Less
Submitted 7 February, 2020;
originally announced February 2020.
-
Mobile Communications Beyond 52.6 GHz: Waveforms, Numerology, and Phase Noise Challenge
Authors:
Toni Levanen,
Oskari Tervo,
Kari Pajukoski,
Markku Renfors,
Mikko Valkama
Abstract:
In this article, the first considerations for the 5G New Radio (NR) physical layer evolution to support beyond 52.6GHz communications are provided. In addition, the performance of both OFDM based and DFT-s-OFDM based networks are evaluated with special emphasis on the phase noise (PN) induced distortion. It is shown that DFT-s-OFDM is more robust against PN under 5G NR Release 15 assumptions, name…
▽ More
In this article, the first considerations for the 5G New Radio (NR) physical layer evolution to support beyond 52.6GHz communications are provided. In addition, the performance of both OFDM based and DFT-s-OFDM based networks are evaluated with special emphasis on the phase noise (PN) induced distortion. It is shown that DFT-s-OFDM is more robust against PN under 5G NR Release 15 assumptions, namely regarding the supported phase tracking reference signal (PTRS) designs, since it enables more effective PN mitigation directly in the time domain. To further improve the PN compensation capabilities, the PTRS design for DFT-s-OFDM is revised, while for the OFDM waveform a novel block PTRS structure is introduced, providing similar link performance as DFT-s-OFDM with enhanced PTRS design. We demonstrate that the existing 5G NR Release 15 solutions can be extended to support efficient mobile communications at 60GHz carrier frequency with the enhanced PTRS structures. In addition, DFT-s-OFDM based downlink for user data could be considered for beyond 52.6GHz communications to further improve system power efficiency and performance with higher order modulation and coding schemes. Finally, network link budget and cell size considerations are provided, showing that at certain bands with specific transmit power regulation, the cell size can eventually be downlink limited.
△ Less
Submitted 8 May, 2020; v1 submitted 19 December, 2019;
originally announced December 2019.
-
PAPR Reduction with Mixed-Numerology OFDM
Authors:
Selahattin Gökceli,
Toni Levanen,
Juha Yli-Kaakinen,
Taneli Riihonen,
Markku Renfors,
Mikko Valkama
Abstract:
High peak-to-average power ratio (PAPR) is a critical problem in orthogonal frequency-division multiplexing (OFDM). The fifth-generation New Radio (5G NR) facilitates the utilization of multiple heterogeneous bandwidth parts (BWPs), which complicates the PAPR problem even further and introduces inter-numerology interference (INI) between the BWPs. This paper proposes two novel schemes to reduce th…
▽ More
High peak-to-average power ratio (PAPR) is a critical problem in orthogonal frequency-division multiplexing (OFDM). The fifth-generation New Radio (5G NR) facilitates the utilization of multiple heterogeneous bandwidth parts (BWPs), which complicates the PAPR problem even further and introduces inter-numerology interference (INI) between the BWPs. This paper proposes two novel schemes to reduce the PAPR of mixed-numerology OFDM signals. The first scheme is an original enhanced iterative clipping-and-error-filtering (ICEF) approach that cancels efficiently the INI along with PAPR reduction. This allows to achieve efficient PAPR reduction while being compatible with well-known windowed overlap-and-add (WOLA) processing. The second scheme is based on fast-convolution (FC) processing, where PAPR reduction is embedded in the FC filtering carried out using overlapping processing blocks. This allows one to use any existing block-wise PAPR reduction method to reduce the composite signals' PAPR with arbitrary BWP waveforms, and it is thus especially well suited for processing mixed-numerology composite waveforms carrying multiple BWPs with different OFDM numerologies. The performance of the proposed algorithms is evaluated in the 5G NR context, and the essential performance advantages are demonstrated and quantified.
△ Less
Submitted 5 September, 2019;
originally announced September 2019.
-
Positioning and Location-Aware Communications for Modern Railways with 5G New Radio
Authors:
Jukka Talvitie,
Toni Levanen,
Mike Koivisto,
Tero Ihalainen,
Kari Pajukoski,
Mikko Valkama
Abstract:
Providing high-capacity radio connectivity for high-speed trains (HSTs) is one of the most important use cases of emerging 5G New Radio (NR) networks. In this article, we show that 5G NR technology can also facilitate high-accuracy continuous localization and tracking of HSTs. Furthermore, we describe and demonstrate how the NR network can utilize the continuous location information for efficient…
▽ More
Providing high-capacity radio connectivity for high-speed trains (HSTs) is one of the most important use cases of emerging 5G New Radio (NR) networks. In this article, we show that 5G NR technology can also facilitate high-accuracy continuous localization and tracking of HSTs. Furthermore, we describe and demonstrate how the NR network can utilize the continuous location information for efficient beam-management and beamforming, as well as for downlink Doppler precompensation in the single-frequency network context. Additionally, with particular focus on millimeter wave networks, novel concepts for low-latency intercarrier interference (ICI) estimation and compensation, due to residual Doppler and oscillator phase noise, are described and demonstrated. The provided numerical results at 30 GHz operating band show that sub-meter positioning and sub-degree beam-direction accuracies can be obtained with very high probabilities in the order of 95-99%. The results also show that the described Doppler precompensation and ICI estimation and cancellation methods substantially improve the throughput of the single-frequency HST network.
△ Less
Submitted 6 May, 2019; v1 submitted 29 April, 2019;
originally announced May 2019.
-
Frequency-Selective PAPR Reduction for OFDM
Authors:
Selahattin Gökceli,
Toni Levanen,
Taneli Riihonen,
Markku Renfors,
Mikko Valkama
Abstract:
We study the peak-to-average power ratio (PAPR) problem in orthogonal frequency-division multiplexing (OFDM) systems. In conventional clipping and filtering based PAPR reduction techniques, clipping noise is allowed to spread over the whole active passband, thus degrading the transmit signal quality similarly at all active subcarriers. However, since modern radio networks support frequency-multipl…
▽ More
We study the peak-to-average power ratio (PAPR) problem in orthogonal frequency-division multiplexing (OFDM) systems. In conventional clipping and filtering based PAPR reduction techniques, clipping noise is allowed to spread over the whole active passband, thus degrading the transmit signal quality similarly at all active subcarriers. However, since modern radio networks support frequency-multiplexing of users and services with highly different quality-of-service expectations, clipping noise from PAPR reduction should be distributed unequally over the corresponding physical resource blocks (PRBs). To facilitate this, we present an efficient PAPR reduction technique, where clipping noise can be flexibly controlled and filtered inside the transmitter passband, allowing to control the transmitted signal quality per PRB. Numerical results are provided in 5G New Radio (NR) mobile network context, demonstrating the flexibility and efficiency of the proposed method.
△ Less
Submitted 1 April, 2019; v1 submitted 20 February, 2019;
originally announced February 2019.
-
Transparent Tx and Rx Waveform Processing for 5G New Radio Mobile Communications
Authors:
Toni Levanen,
Juho Pirskanen,
Kari Pajukoski,
Markku Renfors,
Mikko Valkama
Abstract:
Several different waveform processing techniques have been studied and proposed for the 5G new radio (NR) physical layer, to support new mixed numerology and asynchronous services. The evaluation and comparison of these different techniques is commonly based on matched waveform processing in the transmitter and receiver units. In this article, it is shown that different techniques can be flexibly…
▽ More
Several different waveform processing techniques have been studied and proposed for the 5G new radio (NR) physical layer, to support new mixed numerology and asynchronous services. The evaluation and comparison of these different techniques is commonly based on matched waveform processing in the transmitter and receiver units. In this article, it is shown that different techniques can be flexibly mixed, allowing to separately optimize complexity-performance trade-offs for transmitter and receiver implementations. Mixing of different waveform processing techniques is possible by setting adequate requirements for transmitter and receiver baseband processing allowing transparent design. The basic framework of how transmitter and receiver units can be independently applied and evaluated in the context of transparent design and an extensive set of examples of the achievable radio link performance with unmatched transmitter and receiver waveform processing are provided. The discussed approach and solutions simplify standardization, improve transparent transmitter and receiver coexistence, and allow future-proof evolution path for performance improvements in 5G NR physical layer hardware and algorithm design.
△ Less
Submitted 27 August, 2018;
originally announced August 2018.
