-
Graphene-Flakes Printed Wideband Elliptical Dipole Antenna for Low Cost Wireless Communications Applications
Authors:
Antti Lamminen,
Kirill Arapov,
Gijsbertus de With,
Samiul Haque,
Henrik G. O. Sandberg,
Heiner Friedrich,
Vladimir Ermolov
Abstract:
This letter presents the design, manufacturing and operational performance of a graphene-flakes based screenprinted wideband elliptical dipole antenna operating from 2 GHz up to 5 GHz for low cost wireless communications applications. To investigate radio frequency (RF) conductivity of the printed graphene, a coplanar waveguide (CPW) test structure was designed, fabricated and tested in the freque…
▽ More
This letter presents the design, manufacturing and operational performance of a graphene-flakes based screenprinted wideband elliptical dipole antenna operating from 2 GHz up to 5 GHz for low cost wireless communications applications. To investigate radio frequency (RF) conductivity of the printed graphene, a coplanar waveguide (CPW) test structure was designed, fabricated and tested in the frequency range from 1 GHz to 20 GHz. Antenna and CPW were screen-printed on Kapton substrates using a graphene paste formulated with a graphene to binder ratio of 1:2. A combination of thermal treatment and subsequent compression rolling is utilized to further decrease the sheet resistance for printed graphene structures, ultimately reaching 4 Ohm/sq. at 10 μm thicknesses. For the graphene-flakes printed antenna an antenna efficiency of 60% is obtained. The measured maximum antenna gain is 2.3 dBi at 4.8 GHz. Thus the graphene-flakes printed antenna adds a total loss of only 3.1 dB to an RF link when compared to the same structure screen-printed for reference with a commercial silver ink. This shows that the electrical performance of screen-printed graphene flakes, which also does not degrade after repeated bending, is suitable for realizing low-cost wearable RF wireless communication devices.
△ Less
Submitted 2 May, 2017;
originally announced May 2017.
-
Load-depth sensing of isotropic, linear viscoelastic materials using rigid axisymmetric indenters
Authors:
P. G. Th. van der Varst,
A. A. F. van de Ven,
G. de With
Abstract:
An indentation experiment involves five variables: indenter shape, material behavior of the substrate, contact size, applied load and indentation depth. Only three variable are known afterwards, namely, indenter shape, plus load and depth as function of time. As the contact size is not measured and the determination of the material properties is the very aim of the test; two equations are needed t…
▽ More
An indentation experiment involves five variables: indenter shape, material behavior of the substrate, contact size, applied load and indentation depth. Only three variable are known afterwards, namely, indenter shape, plus load and depth as function of time. As the contact size is not measured and the determination of the material properties is the very aim of the test; two equations are needed to obtain a mathematically solvable system.
For elastic materials, the contact size can always be eliminated once and for all in favor of the depth; a single relation between load, depth and material properties remains with the latter variable as unknown.
For viscoelastic materials where hereditary integrals model the constitutive behavior, the relation between depth and contact size usually depends also on the (time-dependent) properties of the material. Solving the inverse problem, i.e., determining the material properties from the experimental data, therefore needs both equations. Extending Sneddon's analysis of the indentation problem for elastic materials to include viscoelastic materials, the two equations mentioned above are derived. To find the time dependence of the material properties the feasibility of Golden and Graham's method of decomposing hereditary integrals (J.M. Golden and G.A.C. Graham. Boundary value problems in linear viscoelasticity, Springer, 1988) is investigated and applied to a single load-unload process and to sinusoidally driven stationary state indentation processes.
△ Less
Submitted 7 June, 2016;
originally announced June 2016.
-
Rejection-free Monte-Carlo sampling for general potentials
Authors:
E. A. J. F. Peters,
G. de With
Abstract:
A Monte Carlo method to sample the classical configurational canonical ensemble is introduced. In contrast to the Metropolis algorithm, where trial moves can be rejected, in this approach collisions take place. The implementation is event-driven, i.e., at scheduled times the collisions occur. A unique feature of the new method is that smooth potentials (instead of only step-wise changing ones) can…
▽ More
A Monte Carlo method to sample the classical configurational canonical ensemble is introduced. In contrast to the Metropolis algorithm, where trial moves can be rejected, in this approach collisions take place. The implementation is event-driven, i.e., at scheduled times the collisions occur. A unique feature of the new method is that smooth potentials (instead of only step-wise changing ones) can be used. Besides an event-driven approach where all particles move simultaneously, we also introduce a straight event-chain implementation. As proof-of-principle a system of Lennard-Jones particles is simulated.
△ Less
Submitted 8 February, 2012; v1 submitted 6 December, 2011;
originally announced December 2011.
