-
Polymer-Derived SiOC Integrated with a Graphene Aerogel As a Highly Stable Li-Ion Battery Anode
Authors:
Gaofeng Shao,
Dorian A. H. Hanaor,
Jun Wang,
Delf Kober,
Shuang Li,
Xifan Wang,
Xiaodong Shen,
Maged F. Bekheet,
Aleksander Gurlo
Abstract:
Amorphous polymer derived silicon oxycarbide (SiOC) is an attractive candidate for Lithium ion battery anodes, as an alternative to graphite, which is limited to a theoretical capacity of 372 mAh/g. However, SiOC tends to exhibit poor transport properties and cycling performance as a result of sparsely distributed carbon clusters and inefficient active sites. To overcome these limitations, we desi…
▽ More
Amorphous polymer derived silicon oxycarbide (SiOC) is an attractive candidate for Lithium ion battery anodes, as an alternative to graphite, which is limited to a theoretical capacity of 372 mAh/g. However, SiOC tends to exhibit poor transport properties and cycling performance as a result of sparsely distributed carbon clusters and inefficient active sites. To overcome these limitations, we designed and fabricated a layered graphene SiOC heterostructure by solvent assisted infiltration of a polymeric precursor into a modified three dimensional graphene aerogel skeleton. The use of a high melting point solvent facilitated the precursors freeze drying, which following pyrolysis yielded SiOC as a layer supported on the surface of nitrogen doped reduced graphene oxide aerogels. The fabrication method employed here modifies the composition and microstructure of the SiOC phase. Among the studied materials, the highest levels of performance were obtained for a sample of moderate SiOC content, in which the graphene network constituted 19.8 wt % of the system. In these materials, a stable reversible charge capacity of 751 mAh/g was achieved at low charge rates. At high charge rates of 1480 mA/g, the capacity retention was ca. 95% (352 mAh/g) after 1000 consecutive cycles. At all rates, Coulombic efficiencies greater than 99% were maintained following the first cycle. Performance across all indicators was majorly improved in the graphene aerogel SiOC nanocomposites, compared with unsupported SiOC. The performance was attributed to mechanisms across multiple length scales. The presence of oxygen rich SiO4-xCx tetrahedral units and a continuous free carbon network within the SiOC provides sites for reversible lithiation, while high ionic and electronic transport is provided by the layered graphene SiOC heterostructure.
△ Less
Submitted 14 April, 2021;
originally announced April 2021.
-
An Effective Strategy to Enable Argyrodite Sulfides as Superb Solid-State Electrolytes: Safeguarding Remarkable Ionic Conductivity and Interfacial Stability with Electrodes
Authors:
Hongjie Xu,
Yuran Yu,
Junhua Hu,
Zhuo Wang,
Guosheng Shao
Abstract:
The argyrodite sulfides are getting more and more attractive as highly promising solid-state electrolytes (SSEs) for high-performance all-solid-state batteries (ASSBs), owing to their high ionic conductivity, adequate plasticity, and decent mechanical strength. However, their poor incompatibility with Li metal anode and high voltage cathodes and as well as serious sensitivity to air significantly…
▽ More
The argyrodite sulfides are getting more and more attractive as highly promising solid-state electrolytes (SSEs) for high-performance all-solid-state batteries (ASSBs), owing to their high ionic conductivity, adequate plasticity, and decent mechanical strength. However, their poor incompatibility with Li metal anode and high voltage cathodes and as well as serious sensitivity to air significantly hinder their practical applications. Herein, we have devised an effective strategy to overcome these challenging shortcomings through modification of chalcogen chemistry under the guidance of theoretical modeling. The resultant Li6.25PS4O1.25Cl0.75 delivered excellent electrochemical compatibility with both pure Li anode and high-voltage LiCoO2 cathode, without detrimental impact upon the superb ionic conductivity of the pristine sulfide. Furthermore, the current SSE also exhibited highly improved stability to oxygen and moisture in air, with further advantage being more insulating to electrons. The remarkably enhanced compatibility with electrodes is attributed to in situ formation of solid anode electrolyte interphase (AEI) and cathode electrolyte interphase (CEI) layers. The formation of in situ AEI enabled ultra-stable Li plating/stripping at a record high current density up to 1 mAh cm-2 in Li|Li6.25PS4O1.25Cl0.75|Li symmetric cells over 1800 hours. The in situ CEI facilitated protection of the SSE from decomposition at elevated voltage. Consequently, the synergistic effect of AEI and CEI helped the LiCoO2|Li6.25PS4O1.25Cl0.75|Li battery cell to achieve markedly better cycling stability than that using the pristine Li6PS5Cl as SSE, at a high areal loading of the active cathode material (4 mg cm-2). This work adds a desirable SSE in the argyrodite sulfide family, so that high-performance solid battery cells could even be fabricated in ambient air.
△ Less
Submitted 17 October, 2020;
originally announced October 2020.
-
Graphene nanopipette enabled liquid delivery at zeptoliter precision
Authors:
Shi Qiu,
Yu Chen,
Gediminas Gervinskas,
Ross K. W. Marceau,
Changxi Zheng,
Gang Sha,
Jing Fu
Abstract:
Accurate extraction of liquid is the first step towards low-volume liquid delivery and nanocharacterization, which plays a significant role in biomedical research. In this study, a tip-shaped graphene nanopipette (GNP) is proposed by encapsulating the biomolecule solution on the prefabricated metal tip with graphene. The volume of the encapsulated liquid is highly controllable at zeptoliter precis…
▽ More
Accurate extraction of liquid is the first step towards low-volume liquid delivery and nanocharacterization, which plays a significant role in biomedical research. In this study, a tip-shaped graphene nanopipette (GNP) is proposed by encapsulating the biomolecule solution on the prefabricated metal tip with graphene. The volume of the encapsulated liquid is highly controllable at zeptoliter precision by tuning the encapsulating speed and the number of graphene encapsulation rounds. Using protein (ferritin) solution as an example, it has been confirmed by finite element analysis and the controlled experiments that the GNP allows the delivery of ferritin solution at the zeptoliter-scale. Furthermore, GNP is demonstrated as a new type of tip-shaped liquid cell, which is suitable for multiple nanocharacterization techniques. In particular, due to the ultra-sharp tip shape, isotope (13C)-labelled glucose solution encapsulated in GNP has been characterized by atom probe tomography (APT) in the laser-pulsed mode. Analysis of the mass spectrum and the reconstructed three-dimensional chemical maps reveals the quantitative distribution and the compositions of individual glucose molecules. The GNP is expected to be introduced to deliver liquid in the range of zeptoliters to attoliters, and brings a new capability for characterization of biological specimens in their near-native state.
△ Less
Submitted 19 August, 2020;
originally announced August 2020.
-
Direct imaging of liquid-nanoparticle interface with atom probe tomography
Authors:
Shi. Qiu,
Changxi Zheng,
Qi Zhou,
Dashen Dong,
Qianqian Shi,
Vivek Garg,
Shuo Zhang,
Wenlong Cheng,
Ross K. W. Marceau,
Gang Sha,
Jing Fu
Abstract:
Understanding the structure and chemical composition at the liquid-nanoparticle (NP) interface is crucial for a wide range of physical, chemical and biological processes. In this study, direct imaging of the liquid-NP interface by atom probe tomography (APT) is reported for the first time, which reveals the distributions and the interactions of key atoms and molecules in this critical domain. The…
▽ More
Understanding the structure and chemical composition at the liquid-nanoparticle (NP) interface is crucial for a wide range of physical, chemical and biological processes. In this study, direct imaging of the liquid-NP interface by atom probe tomography (APT) is reported for the first time, which reveals the distributions and the interactions of key atoms and molecules in this critical domain. The APT specimen is prepared by controlled graphene encapsulation of the solution containing nanoparticles on a metal tip, with an end radius in the range of 50 nm to allow field ionization and evaporation. Using Au nanoparticles (AuNPs) in suspension as an example, analysis of the mass spectrum and three-dimensional (3D) chemical maps from APT provides a detailed image of the water-gold interface with near-atomic resolution. At the water-gold interface, the formation of an electrical double layer (EDL) rich in water (H2O) molecules has been observed, which results from the charge from the binding between the trisodium-citrate layer and the AuNP. In the bulk water region, the density of reconstructed H2O has been shown to be consistent, reflecting a highly packed density of H2O molecules after graphene encapsulation. This study is the first demonstration of direct imaging of liquid-NP interface using APT with results providing an atom-by-atom 3D dissection of the liquid-NP interface.
△ Less
Submitted 18 May, 2020;
originally announced May 2020.
-
Improved oxidation resistance of high emissivity coatings on fibrous ceramic for reusable space system
Authors:
Gaofeng Shao,
Yucao Lu,
Dorian A. H. Hanaor,
Sheng Cui,
Jian Jiao,
Xiaodong Shen
Abstract:
To develop high emissivity coatings on fibrous ceramic substrates with improved thermal resistance for reusable space systems, WSi2-MoSi2-Si-SiB6-borosilicate glass coatings were prepared on fibrous ZrO2 by slurry dipping and subsequent high temperature rapid sintering. A coating with 50 wt% WSi2 and 50 wt% MoSi2 presents optimal thermal stability with only 10.06 mg/cm2 mass loss and 4.0 % emissiv…
▽ More
To develop high emissivity coatings on fibrous ceramic substrates with improved thermal resistance for reusable space systems, WSi2-MoSi2-Si-SiB6-borosilicate glass coatings were prepared on fibrous ZrO2 by slurry dipping and subsequent high temperature rapid sintering. A coating with 50 wt% WSi2 and 50 wt% MoSi2 presents optimal thermal stability with only 10.06 mg/cm2 mass loss and 4.0 % emissivity decrease in the wavelength regime of 1.27 to 1.73 microns after 50 h oxidation at 1773 K. The advantages of double phase metal silicide coatings combining WSi2 and MoSi2 include improved thermal compatibility with the substrate and an enhanced glass mediated self healing ability.
△ Less
Submitted 7 June, 2021; v1 submitted 11 February, 2019;
originally announced February 2019.
-
From anti-perovskite to double anti-perovskite: lattice chemistry basis for super-fast transportation of Li+ ions in cubic solid lithium halogen-chalcogenides
Authors:
Zhuo Wang,
Hongjie Xu,
Minjie Xuan,
Guosheng Shao
Abstract:
Using a materials genome approach on the basis of the density functional theory, we have formulated a new class of inorganic electrolytes for fast diffusion of Li+ ions, through fine-tuning of lattice chemistry of anti-perovskite structures. Systematic modelling has been carried out to elaborate the structural stability and ion transportation characteristics in Li3AX based cubic anti-perovskite, t…
▽ More
Using a materials genome approach on the basis of the density functional theory, we have formulated a new class of inorganic electrolytes for fast diffusion of Li+ ions, through fine-tuning of lattice chemistry of anti-perovskite structures. Systematic modelling has been carried out to elaborate the structural stability and ion transportation characteristics in Li3AX based cubic anti-perovskite, through alloying on the chalcogen lattice site (A) and alternative occupancy of the halogen site (X). In addition to identifying effective ways for reduction of diffusion barriers for Li+ ions in anti-perovskite phases via suitable designation of lattice occupancy, the current theoretical study leads to discovery and synthesis of a new phase with a double-anti-perovskite structure, Li6OSI2 (or Li3O0.5S0.5I). Such a new compound is of fairly low activation barrier for Li+ diffusion, together with a wide energy band gap to hinder conduction of electrons.
△ Less
Submitted 18 July, 2017;
originally announced July 2017.
-
The humidity sensing properties and mechanism of strontium-hexaferrite ceramics
Authors:
Hui-Feng Zhang,
Jian Li,
Gang-Qin Shao,
Zhen-Sheng Gao,
Jin-Hua Liu,
H. -N. Girish
Abstract:
The humidity sensitivity of n-type strontium-hexaferrite semiconductors, X-type (Sr2Co2Fe28O46) and Z-type (Sr3Co2Fe24O41), are investigated at room temperature. The contact and reactions between water and material surface are demonstrated considering the formation of oxide ion vacancy, singly-ionized / fully-ionized oxide ion vacancy, and the chemisorbed / physisorbed / condensed water. An impeda…
▽ More
The humidity sensitivity of n-type strontium-hexaferrite semiconductors, X-type (Sr2Co2Fe28O46) and Z-type (Sr3Co2Fe24O41), are investigated at room temperature. The contact and reactions between water and material surface are demonstrated considering the formation of oxide ion vacancy, singly-ionized / fully-ionized oxide ion vacancy, and the chemisorbed / physisorbed / condensed water. An impedance spectra model is proposed considering the material-electrode interface, interior material, grain boundary, absorbed water and Warburg response. The mechanism of electronic coupled with protonic conduction and humidity sensing mechanism are explained.
△ Less
Submitted 9 August, 2016; v1 submitted 26 July, 2016;
originally announced July 2016.
-
Ferroelectric domain inversion and its stability in lithium niobate thin film on insulator with different thicknesses
Authors:
Guang-hao Shao,
Yu-hang Bai,
Guo-xin Cui,
Chen Li,
Xiang-biao Qiu,
De-qiang Geng,
Di Wu,
Yan-qing Lu
Abstract:
Ferroelectric domain inversion and its effect on the stability of lithium niobate thin films on insulator (LNOI) are experimentally characterized. Two sets of specimens with different thicknesses varying from submicron to microns are selected. For micron thick samples (~28 um), domain structures are achieved by pulsed electric field poling with electrodes patterned via photolithography. No domain…
▽ More
Ferroelectric domain inversion and its effect on the stability of lithium niobate thin films on insulator (LNOI) are experimentally characterized. Two sets of specimens with different thicknesses varying from submicron to microns are selected. For micron thick samples (~28 um), domain structures are achieved by pulsed electric field poling with electrodes patterned via photolithography. No domain structure deterioration has been observed for a month as inspected using polarizing optical microscopy and etching. As for submicron (540 nm) films, large-area domain inversion is realized by scanning a biased conductive tip in a piezoelectric force microscope. A graphic processing method is taken to evaluate the domain retention. A domain life time of 25.0 h is obtained and possible mechanisms are discussed. Our study gives a direct reference for domain structure-related applications of LNOI, including guiding wave nonlinear frequency conversion, nonlinear wavefront tailoring, electro-optic modulation, and piezoelectric devices.
△ Less
Submitted 19 April, 2016;
originally announced April 2016.
-
Negative differential resistance: another banana?
Authors:
J. Li,
H. -F. Zhang,
G. -Q. Shao,
B. -L. Wu,
S. -X. Ouyang
Abstract:
Just like the artefact found in ferroelectric hysteresis loops, the nearly identical NDR effect shown in Sr3Co2Fe24O41, TiO2, Al2O3, glass and even banana skins is confirmed to be a kind of water behavior. The combination of water induced tunneling effect, water decomposition and absorption plays a crucial role in the NDR effect. The results and mechanism demonstrated here illustrate that much att…
▽ More
Just like the artefact found in ferroelectric hysteresis loops, the nearly identical NDR effect shown in Sr3Co2Fe24O41, TiO2, Al2O3, glass and even banana skins is confirmed to be a kind of water behavior. The combination of water induced tunneling effect, water decomposition and absorption plays a crucial role in the NDR effect. The results and mechanism demonstrated here illustrate that much attention should be paid to the chemical environment when studying electrical properties of materials / devices.
△ Less
Submitted 23 September, 2014;
originally announced September 2014.
-
Magnetic / dielectric anomalies and magnetodielectric / magnetoelectric effects in Z- and W-type hexaferrites
Authors:
J. Li,
H. -F. Zhang,
G. -Q. Shao,
W. Cai,
D. Chen,
G. -G. Zhao,
B. -L. Wu,
S. -X. Ouyang
Abstract:
Two kinds of specimens, with the major phase of Sr3Co2Fe24O41 (Sr3Co2Z) and SrCo2Fe16O27 (SrCo2W) hexaferrites respectively, were fabricated through solid-state reaction. The phase composition, magnetic and dielectric properties, magnetodielectric (MD) effect, magnetoelectric (ME) effect and pyroelectric properties were studied. Results show that magnetic and dielectric anomalies are induced by th…
▽ More
Two kinds of specimens, with the major phase of Sr3Co2Fe24O41 (Sr3Co2Z) and SrCo2Fe16O27 (SrCo2W) hexaferrites respectively, were fabricated through solid-state reaction. The phase composition, magnetic and dielectric properties, magnetodielectric (MD) effect, magnetoelectric (ME) effect and pyroelectric properties were studied. Results show that magnetic and dielectric anomalies are induced by the magnetocrystalline anisotropy (MCA) transition. They can be considered as characteristic properties (e.g., Sr3Co2Z at 370 K) but are not a sufficient condition for the MD and ME coupling. The T-block structure, existing in Sr3Co2Z but absent in SrCo2W, results in the dielectric response with ferroelectric (FE) and magnetic contributions.
△ Less
Submitted 31 August, 2014; v1 submitted 14 July, 2014;
originally announced July 2014.
-
Why are Orbital Currents Central to High Tc Theory?
Authors:
Patrick A. Lee,
Guobin Sha
Abstract:
We explain qualitatively why the staggered flux state plays a central role in the SU(2) formulation of the t-J model, which we use to model the pseudogap state in underdoped cuprates. This point of view is supported by studies of projected wavefunctions. In addition to staggered orbital current correlations, we present here for the first time results of correlations involving hole and spin chira…
▽ More
We explain qualitatively why the staggered flux state plays a central role in the SU(2) formulation of the t-J model, which we use to model the pseudogap state in underdoped cuprates. This point of view is supported by studies of projected wavefunctions. In addition to staggered orbital current correlations, we present here for the first time results of correlations involving hole and spin chirality and show that the two are closely related. The staggered flux state allows us to construct cheap and fast vortices, which may hold the key to explaining the many anomalous properties of the normal state.
△ Less
Submitted 7 October, 2002; v1 submitted 24 September, 2002;
originally announced September 2002.
