Showing 1–50 of 88 results for author: Schoelkopf, R J

Low loss lumped-element inductors made from granular aluminum

Authors: Vishakha Gupta, Patrick Winkel, Neel Thakur, Peter van Vlaanderen, Yanhao Wang, Suhas Ganjam, Luigi Frunzio, Robert J. Schoelkopf

Abstract: Lumped-element inductors are an integral component in the circuit QED toolbox. However, it is challenging to build inductors that are simultaneously compact, linear and low-loss with standard approaches that either rely on the geometric inductance of superconducting thin films or on the kinetic inductance of Josephson junctions arrays. In this work, we overcome this challenge by utilizing the high… ▽ More Lumped-element inductors are an integral component in the circuit QED toolbox. However, it is challenging to build inductors that are simultaneously compact, linear and low-loss with standard approaches that either rely on the geometric inductance of superconducting thin films or on the kinetic inductance of Josephson junctions arrays. In this work, we overcome this challenge by utilizing the high kinetic inductance offered by superconducting granular aluminum (grAl). We demonstrate lumped-element inductors with a few nH of inductance that are up to $100$ times more compact than inductors built from pure aluminum (Al). To characterize the properties of these linear inductors, we first report on the performance of lumped-element resonators built entirely out of grAl with sheet inductances varying from $30-320\,$pH/sq and self-Kerr non-linearities of $0.2-20\,\mathrm{Hz/photon}$. Further, we demonstrate ex-situ integration of these grAl inductors into hybrid resonators with Al or tantalum (Ta) capacitor electrodes without increasing total internal losses. Interestingly, the measured internal quality factors systematically decrease with increasing room-temperature resistivity of the grAl film for all devices, indicating a trade-off between compactness and internal loss. For our lowest resistivity grAl films, we measure quality factors reaching $3.5 \times 10^6$ for the all-grAl devices and $4.5 \times 10^6$ for the hybrid grAl/Ta devices, similar to state-of-the-art quantum circuits. Our loss analysis suggests that the surface loss factor of grAl is similar to that of pure Al for our lowest resistivity films, while the increasing losses with resistivity could be explained by increasing conductor loss in the grAl film. △ Less

Submitted 19 November, 2024; originally announced November 2024.

Comments: 10 pages, 7 figures (main text); 11 pages, 7 figures (supplementary)

Microwave loss characterization using multi-mode superconducting resonators

Authors: Chan U Lei, Suhas Ganjam, Lev Krayzman, Archan Banerjee, Kim Kisslinger, Sooyeon Hwang, Luigi Frunzio, Robert J. Schoelkopf

Abstract: Measuring the losses arising from different materials and interfaces is crucial to improving the coherence of superconducting quantum circuits. Although this has been of interest for a long time, current studies can either only provide bounds to those losses, or require several devices for a complete characterization. In this work, we introduce a method to measure the microwave losses of materials… ▽ More Measuring the losses arising from different materials and interfaces is crucial to improving the coherence of superconducting quantum circuits. Although this has been of interest for a long time, current studies can either only provide bounds to those losses, or require several devices for a complete characterization. In this work, we introduce a method to measure the microwave losses of materials and interfaces with a single multi-mode superconducting resonator. We demonstrate a formalism for analyzing the loss sensitivity of multi-mode systems and discuss the design strategies of multi-mode resonators for material loss studies. We present two types of multi-mode superconducting resonators for the study of bulk superconductors: the forky whispering-gallery-mode resonator (FWGMR) and the ellipsoidal cavity. We use these resonators to measure the surface dielectric, conductor, and seam losses of high-purity (5N5) aluminum and aluminum alloy (6061), as well as how they are affected by chemical etching, diamond turning, and thin-film coating. We find that chemical etching and diamond turning reduce both the surface dielectric and conductive losses of high-purity aluminum, but provide no appreciable improvement to the seam. Coating the surfaces of diamond-turned aluminum alloys with e-beam evaporated or sputtered aluminum thin-films significantly reduces all three losses under study. In addition, we study the effect of chemical etching on the surface of high-purity aluminum using transmission electron microscopy (TEM) and find that the chemical etching process creates a thinner and more uniform oxide layer, consistent with the observed improvement in the surface dielectric loss. △ Less

Submitted 2 May, 2023; originally announced May 2023.

Acoustic radiation from a superconducting qubit: From spontaneous emission to Rabi oscillations

Authors: Vijay Jain, Vladislav D. Kurilovich, Yanni D. Dahmani, Chan U Lei, David Mason, Taekwan Yoon, Peter T. Rakich, Leonid I. Glazman, Robert J. Schoelkopf

Abstract: Acoustic spontaneous emission into bulk dielectrics can be a strong source of decoherence in quantum devices, especially when a qubit is in the presence of piezoelectric materials. We study the dynamics of a qubit coupled to an acoustic resonator by a piezoelectric film. By varying the surface topography of the resonator from rough to polished to shaped, we explore the crossover from fast decay of… ▽ More Acoustic spontaneous emission into bulk dielectrics can be a strong source of decoherence in quantum devices, especially when a qubit is in the presence of piezoelectric materials. We study the dynamics of a qubit coupled to an acoustic resonator by a piezoelectric film. By varying the surface topography of the resonator from rough to polished to shaped, we explore the crossover from fast decay of an excited qubit to quantum-coherent coupling between the qubit and an isolated phonon mode. Our experimental approach may be used for precision measurements of crystalline vibrations, the design of quantum memories, and the study of electro-mechanical contributions to dielectric loss. △ Less

Submitted 14 November, 2022; originally announced November 2022.

Comments: 7 pages, 4 figures; 19 pages supplementary, 5 supplementary figures

Simultaneous Brillouin and piezoelectric coupling to a high-frequency bulk acoustic resonator

Authors: Taekwan Yoon, David Mason, Vijay Jain, Yiwen Chu, Prashanta Kharel, William H. Renninger, Liam Collins, Luigi Frunzio, Robert J Schoelkopf, Peter T Rakich

Abstract: Bulk acoustic resonators support robust, long-lived mechanical modes, capable of coupling to various quantum systems. In separate works, such devices have achieved strong coupling to both superconducting qubits, via piezoelectricity, and optical cavities, via Brillouin interactions. In this work, we present a novel hybrid microwave/optical platform capable of coupling to bulk acoustic waves throug… ▽ More Bulk acoustic resonators support robust, long-lived mechanical modes, capable of coupling to various quantum systems. In separate works, such devices have achieved strong coupling to both superconducting qubits, via piezoelectricity, and optical cavities, via Brillouin interactions. In this work, we present a novel hybrid microwave/optical platform capable of coupling to bulk acoustic waves through cavity-enhanced piezoelectric and photoelastic interactions. The modular, tunable system achieves fully resonant and well-mode-matched interactions between a 3D microwave cavity, a high-frequency bulk acoustic resonator, and a Fabry Perot cavity. We realize this piezo-Brillouin interaction in x-cut quartz, demonstrating the potential for strong optomechanical interactions and high cooperativity using optical cavity enhancement. We further show how this device functions as a bidirectional electro-opto-mechanical transducer, with quantum efficiency exceeding $10^{-8}$, and a feasible path towards unity conversion efficiency. The high optical sensitivity and ability to apply large resonant microwave field in this system also offers a new tool for probing anomalous electromechanical couplings, which we demonstrate by investigating (nominally-centrosymmetric) CaF$_2$ and revealing a parasitic piezoelectricity of 83 am/V. Such studies are an important topic for emerging quantum technologies, and highlight the versatility of this new hybrid platform. △ Less

Submitted 30 January, 2023; v1 submitted 12 August, 2022; originally announced August 2022.

Precision measurement of the microwave dielectric loss of sapphire in the quantum regime with parts-per-billion sensitivity

Authors: Alexander P. Read, Benjamin J. Chapman, Chan U Lei, Jacob C. Curtis, Suhas Ganjam, Lev Krayzman, Luigi Frunzio, Robert J. Schoelkopf

Abstract: Dielectric loss is known to limit state-of-the-art superconducting qubit lifetimes. Recent experiments imply upper bounds on bulk dielectric loss tangents on the order of $100$ parts-per-billion, but because these inferences are drawn from fully fabricated devices with many loss channels, they do not definitively implicate or exonerate the dielectric. To resolve this ambiguity, we have devised a m… ▽ More Dielectric loss is known to limit state-of-the-art superconducting qubit lifetimes. Recent experiments imply upper bounds on bulk dielectric loss tangents on the order of $100$ parts-per-billion, but because these inferences are drawn from fully fabricated devices with many loss channels, they do not definitively implicate or exonerate the dielectric. To resolve this ambiguity, we have devised a measurement method capable of separating and resolving bulk dielectric loss with a sensitivity at the level of $5$ parts per billion. The method, which we call the dielectric dipper, involves the in-situ insertion of a dielectric sample into a high-quality microwave cavity mode. Smoothly varying the sample's participation in the cavity mode enables a differential measurement of the sample's dielectric loss tangent. The dielectric dipper can probe the low-power behavior of dielectrics at cryogenic temperatures, and does so without the need for any lithographic process, enabling controlled comparisons of substrate materials and processing techniques. We demonstrate the method with measurements of EFG sapphire, from which we infer a bulk loss tangent of $62(7) \times 10^{-9}$ and a substrate-air interface loss tangent of $12(2) \times 10^{-4}$. For a typical transmon, this bulk loss tangent would limit device quality factors to less than $20$ million, suggesting that bulk loss is likely the dominant loss mechanism in the longest-lived transmons on sapphire. We also demonstrate this method on HEMEX sapphire and bound its bulk loss tangent to be less than $15(5) \times 10^{-9}$. As this bound is about 3 times smaller than the bulk loss tangent of EFG sapphire, use of HEMEX sapphire as a substrate would lift the bulk dielectric coherence limit of a typical transmon qubit to several milliseconds. △ Less

Submitted 30 April, 2023; v1 submitted 28 June, 2022; originally announced June 2022.

Comments: 8 pages, 5 figures, and 13 page appendix. Submitted revision synchronizes content with associated journal article, including the addition of figure 7 (methods of cavity measurement) and Appendix H (bounding magnetic bulk loss)

Journal ref: Phys. Rev. Applied 19, 034064 (2023)

Ac losses in field-cooled type I superconducting cavities

Authors: G. Catelani, K. Li, C. J. Axline, T. Brecht, L. Frunzio, R. J. Schoelkopf, L. I. Glazman

Abstract: As superconductors are cooled below their critical temperature, stray magnetic flux can become trapped in regions that remain normal. The presence of trapped flux facilitates dissipation of ac current in a superconductor, leading to losses in superconducting elements of microwave devices. In type II superconductors, dissipation is well-understood in terms of the dynamics of vortices hosting a sing… ▽ More As superconductors are cooled below their critical temperature, stray magnetic flux can become trapped in regions that remain normal. The presence of trapped flux facilitates dissipation of ac current in a superconductor, leading to losses in superconducting elements of microwave devices. In type II superconductors, dissipation is well-understood in terms of the dynamics of vortices hosting a single flux quantum. In contrast, the ac response of type I superconductors with trapped flux has not received much attention. Building on Andreev's early work [Sov. Phys. JETP 24, 1019 (1967)], here we show theoretically that the dominant dissipation mechanism is the absorption of the ac field at the exposed surfaces of the normal regions, while the deformation of the superconducting/normal interfaces is unimportant. We use the developed theory to estimate the degradation of the quality factors in field-cooled cavities, and we satisfactorily compare these theoretical estimates to the measured field dependence of the quality factors of two aluminum cavities. △ Less

Submitted 6 October, 2021; originally announced October 2021.

Comments: 9 pages, 3 figures

Journal ref: Supercond. Sci. Technol. 35, 065016 (2022)

Drive-induced nonlinearities of cavity modes coupled to a transmon ancilla

Authors: Yaxing Zhang, Jacob C. Curtis, Christopher S. Wang, R. J. Schoelkopf, S. M. Girvin

Abstract: High-Q microwave cavity modes coupled to transmon ancillas provide a hardware-efficient platform for quantum computing. Due to their coupling, the cavity modes inherit finite nonlinearity from the transmons. In this work, we theoretically and experimentally investigate how an off-resonant drive on the transmon ancilla modifies the nonlinearities of cavity modes in qualitatively different ways, dep… ▽ More High-Q microwave cavity modes coupled to transmon ancillas provide a hardware-efficient platform for quantum computing. Due to their coupling, the cavity modes inherit finite nonlinearity from the transmons. In this work, we theoretically and experimentally investigate how an off-resonant drive on the transmon ancilla modifies the nonlinearities of cavity modes in qualitatively different ways, depending on the interrelation among cavity-transmon detuning, drive-transmon detuning and transmon anharmonicity. For a cavity-transmon detuning that is smaller than or comparable to the drive-transmon detuning and transmon anharmonicity, the off-resonant transmon drive can induce multiphoton resonances among cavity and transmon excitations that strongly modify cavity nonlinearities as drive parameters vary. For a large cavity-transmon detuning, the drive induces cavity-photon-number-dependent ac Stark shifts of transmon levels that translate into effective cavity nonlinearities. In the regime of weak transmon-cavity coupling, the cavity Kerr nonlinearity relates to the third-order nonlinear susceptibility function $χ^{(3)}$ of the driven ancilla. This susceptibility function provides a numerically efficient way of computing the cavity Kerr particularly for systems with many cavity modes controlled by a single transmon. It also serves as a diagnostic tool for identifying undesired drive-induced multiphoton resonance processes. Lastly, we show that by judiciously choosing the drive amplitude, a single off-resonant transmon drive can be used to cancel the cavity self-Kerr nonlinearity or the inter-cavity cross-Kerr. This provides a way of dynamically correcting the cavity Kerr nonlinearity during bosonic operations or quantum error correction protocols that rely on the cavity modes being linear. △ Less

Submitted 7 March, 2022; v1 submitted 16 June, 2021; originally announced June 2021.

Comments: Improved Figs. 4 and 5 compared to the published version

High coherence superconducting microwave cavities with indium bump bonding

Authors: Chan U Lei, Lev Krayzman, Suhas Ganjam, Luigi Frunzio, Robert J. Schoelkopf

Abstract: Low-loss cavities are important in building high-coherence superconducting quantum computers. Generating high quality joints between parts is crucial to the realization of a scalable quantum computer using the circuit quantum electrodynamics (cQED) framework. In this paper, we adapt the technique of indium bump bonding to the cQED architecture to realize high quality superconducting microwave join… ▽ More Low-loss cavities are important in building high-coherence superconducting quantum computers. Generating high quality joints between parts is crucial to the realization of a scalable quantum computer using the circuit quantum electrodynamics (cQED) framework. In this paper, we adapt the technique of indium bump bonding to the cQED architecture to realize high quality superconducting microwave joints between chips. We use this technique to fabricate compact superconducting cavities in the multilayer microwave integrated quantum circuits (MMIQC) architecture and achieve single photon quality factor over 300 million or single-photon lifetimes approaching 5 ms. To quantify the performance of the resulting seam, we fabricate microwave stripline resonators in multiple sections connected by different numbers of bonds, resulting in a wide range of seam admittances. The measured quality factors combined with the designed seam admittances allow us to bound the conductance of the seam at $g_\text{seam} \ge 2\times 10^{10} /(Ω\text{m})$. Such a conductance should enable construction of micromachined superconducting cavities with quality factor of at least a billion. These results demonstrate the capability to construct very high quality microwave structures within the MMIQC architecture. △ Less

Submitted 24 January, 2020; originally announced January 2020.

Journal ref: Appl. Phys. Lett. 116, 154002 (2020)

Direct Dispersive Monitoring of Charge Parity in Offset-Charge-Sensitive Transmons

Authors: K. Serniak, S. Diamond, M. Hays, V. Fatemi, S. Shankar, L. Frunzio, R. J. Schoelkopf, M. H. Devoret

Abstract: A striking characteristic of superconducting circuits is that their eigenspectra and intermode coupling strengths are well predicted by simple Hamiltonians representing combinations of quantum circuit elements. Of particular interest is the Cooper-pair-box Hamiltonian used to describe the eigenspectra of transmon qubits, which can depend strongly on the offset-charge difference across the Josephso… ▽ More A striking characteristic of superconducting circuits is that their eigenspectra and intermode coupling strengths are well predicted by simple Hamiltonians representing combinations of quantum circuit elements. Of particular interest is the Cooper-pair-box Hamiltonian used to describe the eigenspectra of transmon qubits, which can depend strongly on the offset-charge difference across the Josephson element. Notably, this offset-charge dependence can also be observed in the dispersive coupling between an ancillary readout mode and a transmon fabricated in the offset-charge-sensitive (OCS) regime. We utilize this effect to achieve direct, high-fidelity dispersive readout of the joint plasmon and charge-parity state of an OCS transmon, which enables efficient detection of charge fluctuations and nonequilibrium-quasiparticle dynamics. Specifically, we show that additional high-frequency filtering can extend the charge-parity lifetime of our device by two orders of magnitude, resulting in a significantly improved energy relaxation time $T_1\sim200~μ\mathrm{s}$. △ Less

Submitted 30 July, 2019; v1 submitted 28 February, 2019; originally announced March 2019.

Comments: 11 pages, 9 figures

Journal ref: Phys. Rev. Applied 12, 014052 (2019)

Engineering bilinear mode coupling in circuit QED: Theory and experiment

Authors: Yaxing Zhang, Brian J. Lester, Yvonne Y. Gao, Liang Jiang, R. J. Schoelkopf, S. M. Girvin

Abstract: Photonic states of superconducting microwave cavities controlled by transmon ancillas provide a platform for encoding and manipulating quantum information. A key challenge in scaling up the platform is the requirement to communicate on demand the information between the cavities. It has been recently demonstrated that a tunable bilinear interaction between two cavities can be realized by coupling… ▽ More Photonic states of superconducting microwave cavities controlled by transmon ancillas provide a platform for encoding and manipulating quantum information. A key challenge in scaling up the platform is the requirement to communicate on demand the information between the cavities. It has been recently demonstrated that a tunable bilinear interaction between two cavities can be realized by coupling them to a bichromatically-driven transmon ancilla, which allows swapping and interfering the multi-photon states of the cavities [Gao et al., Phys. Rev. X 8, 021073(2018)]. Here, we explore both theoretically and experimentally the regime of relatively strong drives on the ancilla needed to achieve fast SWAP gates but which can also lead to undesired non-perturbative effects that lower the SWAP fidelity. We develop a theoretical formalism based on linear response theory that allows one to calculate the rate of ancilla-induced interaction, decay and frequency shift of the cavities in terms of a susceptibility matrix. We treat the drives non-perturbatively using Floquet theory, and find that the interference of the two drives can strongly alter the system dynamics even in the regime where the rotating wave approximation applies. We identify two major sources of infidelity due to ancilla decoherence. i) Ancilla dissipation and dephasing leads to incoherent hopping among Floquet states which occurs even when the ancilla is at zero temperature, resulting in a sudden change of the SWAP rate. ii) The cavities inherit finite decay from the relatively lossy ancilla through the inverse Purcell effect; the effect can be enhanced when the drive-induced AC Stark shift pushes certain ancilla transition frequencies to the vicinity of the cavity frequencies. The theoretical predictions agree quantitatively with the experimental results, paving the way for using the theory to design future experiments. △ Less

Submitted 14 January, 2019; v1 submitted 23 August, 2018; originally announced August 2018.

Comments: 43 pages, 18 figures. Extended discussions on transmon-induced cavity dephasing in Sec. IVD

Journal ref: Phys. Rev. A 99, 012314 (2019)

A CNOT gate between multiphoton qubits encoded in two cavities

Authors: Serge Rosenblum, Yvonne Y. Gao, Philip Reinhold, Chen Wang, Christopher J. Axline, Luigi Frunzio, Steven M. Girvin, Liang Jiang, Mazyar Mirrahimi, Michel H. Devoret, Robert J. Schoelkopf

Abstract: Entangling gates between qubits are a crucial component for performing algorithms in quantum computers. However, any quantum algorithm must ultimately operate on error-protected logical qubits encoded in high-dimensional systems. Typically, logical qubits are encoded in multiple two-level systems, but entangling gates operating on such qubits are highly complex and have not yet been demonstrated.… ▽ More Entangling gates between qubits are a crucial component for performing algorithms in quantum computers. However, any quantum algorithm must ultimately operate on error-protected logical qubits encoded in high-dimensional systems. Typically, logical qubits are encoded in multiple two-level systems, but entangling gates operating on such qubits are highly complex and have not yet been demonstrated. Here, we realize a controlled NOT (CNOT) gate between two multiphoton qubits in two microwave cavities. In this approach, we encode a qubit in the high-dimensional space of a single cavity mode, rather than in multiple two-level systems. We couple two such encoded qubits together through a transmon, which is driven by an RF pump to apply the gate within 190 ns. This is two orders of magnitude shorter than the decoherence time of the transmon, enabling a high-fidelity gate operation. These results are an important step towards universal algorithms on error-corrected logical qubits. △ Less

Submitted 19 December, 2017; v1 submitted 15 September, 2017; originally announced September 2017.

Comments: 10 pages, 11 figures (incl. Supplementary Information)

Optimal configurations for normal-metal traps in transmon qubits

Authors: A. Hosseinkhani, R. -P. Riwar, R. J. Schoelkopf, L. I. Glazman, G. Catelani

Abstract: Controlling quasiparticle dynamics can improve the performance of superconducting devices. For example, it has been demonstrated effective in increasing lifetime and stability of superconducting qubits. Here we study how to optimize the placement of normal-metal traps in transmon-type qubits. When the trap size increases beyond a certain characteristic length, the details of the geometry and trap… ▽ More Controlling quasiparticle dynamics can improve the performance of superconducting devices. For example, it has been demonstrated effective in increasing lifetime and stability of superconducting qubits. Here we study how to optimize the placement of normal-metal traps in transmon-type qubits. When the trap size increases beyond a certain characteristic length, the details of the geometry and trap position, and even the number of traps, become important. We discuss for some experimentally relevant examples how to shorten the decay time of the excess quasiparticle density. Moreover, we show that a trap in the vicinity of a Josephson junction can reduce the steady-state quasiparticle density near that junction, thus suppressing the quasiparticle-induced relaxation rate of the qubit. Such a trap also reduces the impact of fluctuations in the generation rate of quasiparticles, rendering the qubit more stable. △ Less

Submitted 8 December, 2017; v1 submitted 28 June, 2017; originally announced June 2017.

Comments: 16 pages, 7 figures; to appear in Phys. Rev. Applied

Journal ref: Phys. Rev. Applied 8, 064028 (2017)

Faithful conversion of propagating quantum information to mechanical motion

Authors: A. P. Reed, K. H. Mayer, J. D. Teufel, L. D. Burkhart, W. Pfaff, M. Reagor, L. Sletten, X. Ma, R. J. Schoelkopf, E. Knill, K. W. Lehnert

Abstract: We convert propagating qubits encoded as superpositions of zero and one photons to the motion of a micrometer-sized mechanical resonator. Using quantum state tomography, we determine the density matrix of both the propagating photons and the mechanical resonator. By comparing a sufficient set of states before and after conversion, we determine the average process fidelity to be… ▽ More We convert propagating qubits encoded as superpositions of zero and one photons to the motion of a micrometer-sized mechanical resonator. Using quantum state tomography, we determine the density matrix of both the propagating photons and the mechanical resonator. By comparing a sufficient set of states before and after conversion, we determine the average process fidelity to be $F_{\textrm{avg}} = 0.83\substack{+0.03-0.06}$ which exceeds the classical bound for the conversion of an arbitrary qubit state. This conversion ability is necessary for using mechanical resonators in emerging quantum communication and modular quantum computation architectures. △ Less

Submitted 7 March, 2017; originally announced March 2017.

Comments: 22 pages, 14 figures (including Supplementary Information)

Schrodinger's catapult: Launching multiphoton quantum states from a microwave cavity memory

Authors: Wolfgang Pfaff, Christopher J Axline, Luke D Burkhart, Uri Vool, Philip Reinhold, Luigi Frunzio, Liang Jiang, Michel H Devoret, Robert J Schoelkopf

Abstract: Encoding quantum states in complex multiphoton fields can overcome loss during signal transmission in a quantum network. Transmitting quantum information encoded in this way requires that locally stored states can be converted to propagating fields. Here we experimentally show the controlled conversion of multiphoton quantum states, like "Schrödinger cat" states, from a microwave cavity quantum me… ▽ More Encoding quantum states in complex multiphoton fields can overcome loss during signal transmission in a quantum network. Transmitting quantum information encoded in this way requires that locally stored states can be converted to propagating fields. Here we experimentally show the controlled conversion of multiphoton quantum states, like "Schrödinger cat" states, from a microwave cavity quantum memory into propagating modes. By parametric conversion using the nonlinearity of a single Josephson junction, we can release the cavity state in ~500 ns, about 3 orders of magnitude faster than its intrinsic lifetime. This `catapult' faithfully converts arbitrary cavity fields to traveling signals with an estimated efficiency of > 90%, enabling on-demand generation of complex itinerant quantum states. Importantly, the release process can be controlled precisely on fast time scales, allowing us to generate entanglement between the cavity and the traveling mode by partial conversion. Our system can serve as the backbone of a microwave quantum network, paving the way towards error-correctable distribution of quantum information and the transfer of highly non-classical states to hybrid quantum systems. △ Less

Submitted 15 December, 2016; originally announced December 2016.

Comments: 18 pages, 13 figures (incl. Supplementary Information)

Journal ref: Nature Physics, Advance Online Publication (2017)

Micromachined integrated quantum circuit containing a superconducting qubit

Authors: T. Brecht, Y. Chu, C. Axline, W. Pfaff, J. Z. Blumoff, K. Chou, L. Krayzman, L. Frunzio, R. J. Schoelkopf

Abstract: We present a device demonstrating a lithographically patterned transmon integrated with a micromachined cavity resonator. Our two-cavity, one-qubit device is a multilayer microwave integrated quantum circuit (MMIQC), comprising a basic unit capable of performing circuit-QED (cQED) operations. We describe the qubit-cavity coupling mechanism of a specialized geometry using an electric field picture… ▽ More We present a device demonstrating a lithographically patterned transmon integrated with a micromachined cavity resonator. Our two-cavity, one-qubit device is a multilayer microwave integrated quantum circuit (MMIQC), comprising a basic unit capable of performing circuit-QED (cQED) operations. We describe the qubit-cavity coupling mechanism of a specialized geometry using an electric field picture and a circuit model, and finally obtain specific system parameters using simulations. Fabrication of the MMIQC includes lithography, etching, and metallic bonding of silicon wafers. Superconducting wafer bonding is a critical capability that is demonstrated by a micromachined storage cavity lifetime $34.3~\mathrm{μs}$, corresponding to a quality factor of 2 million at single-photon energies. The transmon coherence times are $T_1=6.4~\mathrm{μs}$, and $T_2^{Echo}= 11.7~\mathrm{μs}$. We measure qubit-cavity dispersive coupling with rate $χ_{qμ}/2π=-1.17~$MHz, constituting a Jaynes-Cummings system with an interaction strength $g/2π=49~$MHz. With these parameters we are able to demonstrate cQED operations in the strong dispersive regime with ease. Finally, we highlight several improvements and anticipated extensions of the technology to complex MMIQCs. △ Less

Submitted 7 November, 2016; originally announced November 2016.

Journal ref: Phys. Rev. Applied 8, 039902 (2017)

Normal-metal quasiparticle traps for superconducting qubits

Authors: R. -P. Riwar, A. Hosseinkhani, L. D. Burkhart, Y. Y. Gao, R. J. Schoelkopf, L. I. Glazman, G. Catelani

Abstract: The presence of quasiparticles in superconducting qubits emerges as an intrinsic constraint on their coherence. While it is difficult to prevent the generation of quasiparticles, keeping them away from active elements of the qubit provides a viable way of improving the device performance. Here we develop theoretically and validate experimentally a model for the effect of a single small trap on the… ▽ More The presence of quasiparticles in superconducting qubits emerges as an intrinsic constraint on their coherence. While it is difficult to prevent the generation of quasiparticles, keeping them away from active elements of the qubit provides a viable way of improving the device performance. Here we develop theoretically and validate experimentally a model for the effect of a single small trap on the dynamics of the excess quasiparticles injected in a transmon-type qubit. The model allows one to evaluate the time it takes to evacuate the injected quasiparticles from the transmon as a function of trap parameters. With the increase of the trap size, this time decreases monotonically, saturating at the level determined by the quasiparticles diffusion constant and the qubit geometry. We determine the characteristic trap size needed for the relaxation time to approach that saturation value. △ Less

Submitted 14 June, 2016; originally announced June 2016.

Comments: 11 pages, 5 figures

Journal ref: Phys. Rev. B 94, 104516 (2016)

Suspending superconducting qubits by silicon micromachining

Authors: Y. Chu, C. Axline, C. Wang, T. Brecht, Y. Y. Gao, L. Frunzio, R. J. Schoelkopf

Abstract: We present a method for relieving aluminum 3D transmon qubits from a silicon substrate using micromachining. Our technique is a high yield, one-step deep reactive ion etch that requires no additional fabrication processes, and results in the suspension of the junction area and edges of the aluminum film. The drastic change in the device geometry affects both the dielectric and flux noise environme… ▽ More We present a method for relieving aluminum 3D transmon qubits from a silicon substrate using micromachining. Our technique is a high yield, one-step deep reactive ion etch that requires no additional fabrication processes, and results in the suspension of the junction area and edges of the aluminum film. The drastic change in the device geometry affects both the dielectric and flux noise environment experienced by the qubit. In particular, the participation ratios of various dielectric interfaces are significantly modified, and suspended qubits exhibited longer $T_1$'s than non-suspended ones. We also find that suspension increases the flux noise experienced by tunable SQUID-based qubits. △ Less

Submitted 9 June, 2016; originally announced June 2016.

Comments: Main text: 4 pages, 3 figures. Supplementary materials: 6 pages, 5 figures

Continuous quantum nondemolition measurement of the transverse component of a qubit

Authors: U. Vool, S. Shankar, S. O. Mundhada, N. Ofek, A. Narla, K. Sliwa, E. Zalys-Geller, Y. Liu, L. Frunzio, R. J. Schoelkopf, S. M. Girvin, M. H. Devoret

Abstract: Quantum jumps of a qubit are usually observed between its energy eigenstates, also known as its longitudinal pseudo-spin component. Is it possible, instead, to observe quantum jumps between the transverse superpositions of these eigenstates? We answer positively by presenting the first continuous quantum nondemolition measurement of the transverse component of an individual qubit. In a circuit QED… ▽ More Quantum jumps of a qubit are usually observed between its energy eigenstates, also known as its longitudinal pseudo-spin component. Is it possible, instead, to observe quantum jumps between the transverse superpositions of these eigenstates? We answer positively by presenting the first continuous quantum nondemolition measurement of the transverse component of an individual qubit. In a circuit QED system irradiated by two pump tones, we engineer an effective Hamiltonian whose eigenstates are the transverse qubit states, and a dispersive measurement of the corresponding operator. Such transverse component measurements are a useful tool in the driven-dissipative operation engineering toolbox, which is central to quantum simulation and quantum error correction. △ Less

Submitted 20 September, 2016; v1 submitted 25 May, 2016; originally announced May 2016.

Comments: 6 pages, 4 figures and an additional supplementary material

Journal ref: Phys. Rev. Lett. 117, 133601 (2016)

Quantization of inductively-shunted superconducting circuits

Authors: W. C. Smith, A. Kou, U. Vool, I. M. Pop, L. Frunzio, R. J. Schoelkopf, M. H. Devoret

Abstract: We present a method for calculating the energy levels of superconducting circuits that contain highly anharmonic, inductively-shunted modes with arbitrarily strong coupling. Our method starts by calculating the normal modes of the linearized circuit and proceeds with numerical diagonalization in this basis. As an example, we analyze the Hamiltonian of a fluxonium qubit inductively coupled to a rea… ▽ More We present a method for calculating the energy levels of superconducting circuits that contain highly anharmonic, inductively-shunted modes with arbitrarily strong coupling. Our method starts by calculating the normal modes of the linearized circuit and proceeds with numerical diagonalization in this basis. As an example, we analyze the Hamiltonian of a fluxonium qubit inductively coupled to a readout resonator. While elementary, this simple example is nontrivial because it cannot be efficiently treated by the method known as "black-box quantization," numerical diagonalization in the bare harmonic oscillator basis, or perturbation theory. Calculated spectra are compared to measured spectroscopy data, demonstrating excellent quantitative agreement between theory and experiment. △ Less

Submitted 20 October, 2016; v1 submitted 4 February, 2016; originally announced February 2016.

Comments: 10 pages, 7 figures

Journal ref: Phys. Rev. B 94, 144507 (2016)

Surface participation and dielectric loss in superconducting qubits

Authors: Chen Wang, Christopher Axline, Yvonne Y. Gao, Teresa Brecht, Luigi Frunzio, Michel H. Devoret, Robert J. Schoelkopf

Abstract: We study the energy relaxation times ($T_1$) of superconducting transmon qubits in 3D cavities as a function of dielectric participation ratios of material surfaces. This surface participation ratio, representing the fraction of electric field energy stored in a dissipative surface layer, is computed by a two-step finite-element simulation and experimentally varied by qubit geometry. With a clean… ▽ More We study the energy relaxation times ($T_1$) of superconducting transmon qubits in 3D cavities as a function of dielectric participation ratios of material surfaces. This surface participation ratio, representing the fraction of electric field energy stored in a dissipative surface layer, is computed by a two-step finite-element simulation and experimentally varied by qubit geometry. With a clean electromagnetic environment and suppressed non-equilibrium quasiparticle density, we find an approximately proportional relation between the transmon relaxation rates and surface participation ratios. These results suggest dielectric dissipation arising from material interfaces is the major limiting factor for the $T_1$ of transmons in 3D cQED architecture. Our analysis also supports the notion of spatial discreteness of surface dielectric dissipation. △ Less

Submitted 15 October, 2015; v1 submitted 6 September, 2015; originally announced September 2015.

Comments: Main text: 5 pages 4 figures; Supplementary Materials: 6 pages 4 figures 1 table

Journal ref: Appl. Phys. Lett. 107, 162601 (2015)

Planar multilayer circuit quantum electrodynamics

Authors: Z. K. Minev, K. Serniak, I. M. Pop, Z. Leghtas, K. Sliwa, M. Hatridge, L. Frunzio, R. J. Schoelkopf, M. H. Devoret

Abstract: Experimental quantum information processing with superconducting circuits is rapidly advancing, driven by innovation in two classes of devices, one involving planar micro-fabricated (2D) resonators, and the other involving machined three-dimensional (3D) cavities. We demonstrate that circuit quantum electrodynamics can be implemented in a multilayer superconducting structure that combines 2D and 3… ▽ More Experimental quantum information processing with superconducting circuits is rapidly advancing, driven by innovation in two classes of devices, one involving planar micro-fabricated (2D) resonators, and the other involving machined three-dimensional (3D) cavities. We demonstrate that circuit quantum electrodynamics can be implemented in a multilayer superconducting structure that combines 2D and 3D advantages. We employ standard micro-fabrication techniques to pattern each layer, and rely on a vacuum gap between the layers to store the electromagnetic energy. Planar qubits are lithographically defined as an aperture in a conducting boundary of the resonators. We demonstrate the aperture concept by implementing an integrated, two cavity-modes, one transmon-qubit system. △ Less

Submitted 29 May, 2016; v1 submitted 4 September, 2015; originally announced September 2015.

Journal ref: Phys. Rev. Applied 5, 044021 (2016)

Multilayer microwave integrated quantum circuits for scalable quantum computing

Authors: T. Brecht, W. Pfaff, C. Wang, Y. Chu, L. Frunzio, M. H. Devoret, R. J. Schoelkopf

Abstract: As experimental quantum information processing (QIP) rapidly advances, an emerging challenge is to design a scalable architecture that combines various quantum elements into a complex device without compromising their performance. In particular, superconducting quantum circuits have successfully demonstrated many of the requirements for quantum computing, including coherence levels that approach t… ▽ More As experimental quantum information processing (QIP) rapidly advances, an emerging challenge is to design a scalable architecture that combines various quantum elements into a complex device without compromising their performance. In particular, superconducting quantum circuits have successfully demonstrated many of the requirements for quantum computing, including coherence levels that approach the thresholds for scaling. However, it remains challenging to couple a large number of circuit components through controllable channels while suppressing any other interactions. We propose a hardware platform intended to address these challenges, which combines the advantages of integrated circuit fabrication and long coherence times achievable in three-dimensional circuit quantum electrodynamics (3D cQED). This multilayer microwave integrated quantum circuit (MMIQC) platform provides a path toward the realization of increasingly complex superconducting devices in pursuit of a scalable quantum computer. △ Less

Submitted 11 September, 2015; v1 submitted 3 September, 2015; originally announced September 2015.

Comments: 5 pages, 2 figures

Demonstration of superconducting micromachined cavities

Authors: T. Brecht, M. Reagor, Y. Chu, W. Pfaff, C. Wang, L. Frunzio, M. H. Devoret, R. J. Schoelkopf

Abstract: Superconducting enclosures will be key components of scalable quantum computing devices based on circuit quantum electrodynamics (cQED). Within a densely integrated device, they can protect qubits from noise and serve as quantum memory units. Whether constructed by machining bulk pieces of metal or microfabricating wafers, 3D enclosures are typically assembled from two or more parts. The resulting… ▽ More Superconducting enclosures will be key components of scalable quantum computing devices based on circuit quantum electrodynamics (cQED). Within a densely integrated device, they can protect qubits from noise and serve as quantum memory units. Whether constructed by machining bulk pieces of metal or microfabricating wafers, 3D enclosures are typically assembled from two or more parts. The resulting seams potentially dissipate crossing currents and limit performance. In this Letter, we present measured quality factors of superconducting cavity resonators of several materials, dimensions and seam locations. We observe that superconducting indium can be a low-loss RF conductor and form low-loss seams. Leveraging this, we create a superconducting micromachined resonator with indium that has a quality factor of two million despite a greatly reduced mode volume. Inter-layer coupling to this type of resonator is achieved by an aperture located under a planar transmission line. The described techniques demonstrate a proof-of-principle for multilayer microwave integrated quantum circuits for scalable quantum computing. △ Less

Submitted 11 September, 2015; v1 submitted 3 September, 2015; originally announced September 2015.

Comments: 6 pages, 5 figures

Comparing and combining measurement-based and driven-dissipative entanglement stabilization

Authors: Yehan Liu, Shyam Shankar, Nissim Ofek, Michael Hatridge, Anirudh Narla, Katrina Sliwa, Luigi Frunzio, Robert J. Schoelkopf, Michel H. Devoret

Abstract: We demonstrate and contrast two approaches to the stabilization of qubit entanglement by feedback. Our demonstration is built on a feedback platform consisting of two superconducting qubits coupled to a cavity which are measured by a nearly-quantum-limited measurement chain and controlled by high-speed classical logic circuits. This platform is used to stabilize entanglement by two nominally disti… ▽ More We demonstrate and contrast two approaches to the stabilization of qubit entanglement by feedback. Our demonstration is built on a feedback platform consisting of two superconducting qubits coupled to a cavity which are measured by a nearly-quantum-limited measurement chain and controlled by high-speed classical logic circuits. This platform is used to stabilize entanglement by two nominally distinct schemes: a "passive" reservoir engineering method and an "active" correction based on conditional parity measurements. In view of the instrumental roles that these two feedback paradigms play in quantum error-correction and quantum control, we directly compare them on the same experimental setup. Further, we show that a second layer of feedback can be added to each of these schemes, which heralds the presence of a high-fidelity entangled state in realtime. This "nested" feedback brings about a marked entanglement fidelity improvement without sacrificing success probability. △ Less

Submitted 2 September, 2015; originally announced September 2015.

Comments: 40 pages, 12 figures

Journal ref: Phys. Rev. X 6, 011022 (2016)

A quantum memory with near-millisecond coherence in circuit QED

Authors: Matthew Reagor, Wolfgang Pfaff, Christopher Axline, Reinier W. Heeres, Nissim Ofek, Katrina Sliwa, Eric Holland, Chen Wang, Jacob Blumoff, Kevin Chou, Michael J. Hatridge, Luigi Frunzio, Michel H. Devoret, Liang Jiang, Robert J. Schoelkopf

Abstract: Significant advances in coherence have made superconducting quantum circuits a viable platform for fault-tolerant quantum computing. To further extend capabilities, highly coherent quantum systems could act as quantum memories for these circuits. A useful quantum memory must be rapidly addressable by qubits, while maintaining superior coherence. We demonstrate a novel superconducting microwave cav… ▽ More Significant advances in coherence have made superconducting quantum circuits a viable platform for fault-tolerant quantum computing. To further extend capabilities, highly coherent quantum systems could act as quantum memories for these circuits. A useful quantum memory must be rapidly addressable by qubits, while maintaining superior coherence. We demonstrate a novel superconducting microwave cavity architecture that is highly robust against major sources of loss that are encountered in the engineering of circuit QED systems. The architecture allows for near-millisecond storage of quantum states in a resonator while strong coupling between the resonator and a transmon qubit enables control, encoding, and readout at MHz rates. The observed coherence times constitute an improvement of almost an order of magnitude over those of the best available superconducting qubits. Our design is an ideal platform for studying coherent quantum optics and marks an important step towards hardware-efficient quantum computing with Josephson junction-based quantum circuits. △ Less

Submitted 25 August, 2015; v1 submitted 24 August, 2015; originally announced August 2015.

Journal ref: Phys. Rev. B 94, 014506 (2016)

Coupling an ensemble of electrons on superfluid helium to a superconducting circuit

Authors: Ge Yang, A. Fragner, G. Koolstra, L. Ocola, D. A. Czaplewski, R. J. Schoelkopf, D. I. Schuster

Abstract: The quantized lateral motional states and the spin states of electrons trapped on the surface of superfluid helium have been proposed as basic building blocks of a scalable quantum computer. Circuit quantum electrodynamics (cQED) allows strong dipole coupling between electrons and a high-Q superconducting microwave resonator, enabling such sensitive detection and manipulation of electron degrees o… ▽ More The quantized lateral motional states and the spin states of electrons trapped on the surface of superfluid helium have been proposed as basic building blocks of a scalable quantum computer. Circuit quantum electrodynamics (cQED) allows strong dipole coupling between electrons and a high-Q superconducting microwave resonator, enabling such sensitive detection and manipulation of electron degrees of freedom. Here we present the first realization of a hybrid circuit in which a large number of electrons are trapped on the surface of superfluid helium inside a coplanar waveguide resonator. The high finesse of the resonator allows us to observe large dispersive shifts that are many times the linewidth and make fast and sensitive measurements on the collective vibrational modes of the electron ensemble, as well as the superfluid helium film underneath. Furthermore, a large ensemble coupling is observed in the dispersive regime during experiment, and it shows excellent agreement with our numeric model. The coupling strength of the ensemble to the cavity is found to be >1 MHz per electron, indicating the feasibility of achieving single electron strong coupling. △ Less

Submitted 19 August, 2015; originally announced August 2015.

Comments: main text 5 pages, 4 figures, supplemental information includes 14 pages, 11 figures

Journal ref: Phys. Rev. X 6, 011031 (2016)

Cavity State Manipulation Using Photon-Number Selective Phase Gates

Authors: Reinier W. Heeres, Brian Vlastakis, Eric Holland, Stefan Krastanov, Victor V. Albert, Luigi Frunzio, Liang Jiang, Robert J. Schoelkopf

Abstract: The large available Hilbert space and high coherence of cavity resonators makes these systems an interesting resource for storing encoded quantum bits. To perform a quantum gate on this encoded information, however, complex nonlinear operations must be applied to the many levels of the oscillator simultaneously. In this work, we introduce the Selective Number-dependent Arbitrary Phase (SNAP) gate,… ▽ More The large available Hilbert space and high coherence of cavity resonators makes these systems an interesting resource for storing encoded quantum bits. To perform a quantum gate on this encoded information, however, complex nonlinear operations must be applied to the many levels of the oscillator simultaneously. In this work, we introduce the Selective Number-dependent Arbitrary Phase (SNAP) gate, which imparts a different phase to each Fock state component using an off-resonantly coupled qubit. We show that the SNAP gate allows control over the quantum phases by correcting the unwanted phase evolution due to the Kerr effect. Furthermore, by combining the SNAP gate with oscillator displacements, we create a one-photon Fock state with high fidelity. Using just these two controls, one can construct arbitrary unitary operations, offering a scalable route to performing logical manipulations on oscillator-encoded qubits. △ Less

Submitted 4 March, 2015; originally announced March 2015.

Comments: 9 pages

Journal ref: Phys. Rev. Lett. 115, 137002 (2015)

Holonomic quantum control with continuous variable systems

Authors: Victor V. Albert, Chi Shu, Stefan Krastanov, Chao Shen, Ren-Bao Liu, Zhen-Biao Yang, Robert J. Schoelkopf, Mazyar Mirrahimi, Michel H. Devoret, Liang Jiang

Abstract: Universal computation of a quantum system consisting of superpositions of well-separated coherent states of multiple harmonic oscillators can be achieved by three families of adiabatic holonomic gates. The first gate consists of moving a coherent state around a closed path in phase space, resulting in a relative Berry phase between that state and the other states. The second gate consists of "coll… ▽ More Universal computation of a quantum system consisting of superpositions of well-separated coherent states of multiple harmonic oscillators can be achieved by three families of adiabatic holonomic gates. The first gate consists of moving a coherent state around a closed path in phase space, resulting in a relative Berry phase between that state and the other states. The second gate consists of "colliding" two coherent states of the same oscillator, resulting in coherent population transfer between them. The third gate is an effective controlled-phase gate on coherent states of two different oscillators. Such gates should be realizable via reservoir engineering of systems which support tunable nonlinearities, such as trapped ions and circuit QED. △ Less

Submitted 30 March, 2016; v1 submitted 28 February, 2015; originally announced March 2015.

Comments: 6 pages, 3 figures + 4 page supplement; (v3 scheme now universal; v4 title changed to match published version); gate animations available at http://dancingblobs.krastanov.org/

Journal ref: Phys. Rev. Lett. 116, 140502 (2016)

Universal Control of an Oscillator with Dispersive Coupling to a Qubit

Authors: Stefan Krastanov, Victor V. Albert, Chao Shen, Chang-Ling Zou, Reinier W. Heeres, Brian Vlastakis, Robert J. Schoelkopf, Liang Jiang

Abstract: We investigate quantum control of an oscillator mode off-resonantly coupled to an ancillary qubit. In the strong dispersive regime, we may drive the qubit conditioned on number states of the oscillator, which together with displacement operations can achieve universal control of the oscillator. Based on our proof of universal control, we provide explicit constructions for arbitrary state preparati… ▽ More We investigate quantum control of an oscillator mode off-resonantly coupled to an ancillary qubit. In the strong dispersive regime, we may drive the qubit conditioned on number states of the oscillator, which together with displacement operations can achieve universal control of the oscillator. Based on our proof of universal control, we provide explicit constructions for arbitrary state preparation and arbitrary unitary operation of the oscillator. Moreover, we present an efficient procedure to prepare the number state $\left|n\right\rangle$ using only $O\left(\sqrt{n}\right)$ operations. We also compare our scheme with known quantum control protocols for coupled qubit-oscillator systems. This universal control scheme of the oscillator can readily be implemented using superconducting circuits. △ Less

Submitted 12 March, 2015; v1 submitted 27 February, 2015; originally announced February 2015.

Comments: 5 pages, 3 figures, 2 tables

Journal ref: Phys. Rev. A 92, 040303(R) (2015)

Measurement and Control of Quasiparticle Dynamics in a Superconducting Qubit

Authors: Chen Wang, Yvonne Y. Gao, Ioan M. Pop, Uri Vool, Chris Axline, Teresa Brecht, Reinier W. Heeres, Luigi Frunzio, Michel H. Devoret, Gianluigi Catelani, Leonid I. Glazman, Robert J. Schoelkopf

Abstract: Superconducting circuits have attracted growing interest in recent years as a promising candidate for fault-tolerant quantum information processing. Extensive efforts have always been taken to completely shield these circuits from external magnetic field to protect the integrity of superconductivity. Surprisingly, here we show vortices can improve the performance of superconducting qubits by reduc… ▽ More Superconducting circuits have attracted growing interest in recent years as a promising candidate for fault-tolerant quantum information processing. Extensive efforts have always been taken to completely shield these circuits from external magnetic field to protect the integrity of superconductivity. Surprisingly, here we show vortices can improve the performance of superconducting qubits by reducing the lifetimes of detrimental single-electron-like excitations known as quasiparticles. Using a contactless injection technique with unprecedented dynamic range, we quantitatively distinguish between recombination and trapping mechanisms in controlling the dynamics of residual quasiparticles, and show quantized changes in quasiparticle trapping rate due to individual vortices. These results highlight the prominent role of quasiparticle trapping in future development of superconducting qubits, and provide a powerful characterization tool along the way. △ Less

Submitted 24 October, 2014; v1 submitted 27 June, 2014; originally announced June 2014.

Comments: 8 pages with 4 figures for the main text, 13 pages with 11 figures for supplementary material

Journal ref: Nature Communications 5, 5836 (2014)

Non-Poissonian Quantum Jumps of a Fluxonium Qubit due to Quasiparticle Excitations

Authors: Uri Vool, Ioan M. Pop, Katrina Sliwa, Baleegh Abdo, Chen Wang, Teresa Brecht, Yvonne Y. Gao, Shyam Shankar, Michael Hatridge, Gianluigi Catelani, Mazyar Mirrahimi, Luigi Frunzio, Robert J. Schoelkopf, Leonid I. Glazman, Michel H. Devoret

Abstract: As the energy relaxation time of superconducting qubits steadily improves, non-equilibrium quasiparticle excitations above the superconducting gap emerge as an increasingly relevant limit for qubit coherence. We measure fluctuations in the number of quasiparticle excitations by continuously monitoring the spontaneous quantum jumps between the states of a fluxonium qubit, in conditions where relaxa… ▽ More As the energy relaxation time of superconducting qubits steadily improves, non-equilibrium quasiparticle excitations above the superconducting gap emerge as an increasingly relevant limit for qubit coherence. We measure fluctuations in the number of quasiparticle excitations by continuously monitoring the spontaneous quantum jumps between the states of a fluxonium qubit, in conditions where relaxation is dominated by quasiparticle loss. Resolution on the scale of a single quasiparticle is obtained by performing quantum non-demolition projective measurements within a time interval much shorter than $T_1$, using a quantum limited amplifier (Josephson Parametric Converter). The quantum jumps statistics switches between the expected Poisson distribution and a non-Poissonian one, indicating large relative fluctuations in the quasiparticle population, on time scales varying from seconds to hours. This dynamics can be modified controllably by injecting quasiparticles or by seeding quasiparticle-trapping vortices by cooling down in magnetic field. △ Less

Submitted 9 December, 2014; v1 submitted 6 June, 2014; originally announced June 2014.

Journal ref: Phys. Rev. Lett. 113, 247001 (2014)

Wireless Josephson Amplifier

Authors: A. Narla, K. M. Sliwa, M. Hatridge, S. Shankar, L. Frunzio, R. J. Schoelkopf, M. H. Devoret

Abstract: Josephson junction parametric amplifiers are playing a crucial role in the readout chain in superconducting quantum information experiments. However, their integration with current 3D cavity implementations poses the problem of transitioning between waveguide, coax cables and planar circuits. Moreover, Josephson amplifiers require auxiliary microwave components, like directional couplers and/or hy… ▽ More Josephson junction parametric amplifiers are playing a crucial role in the readout chain in superconducting quantum information experiments. However, their integration with current 3D cavity implementations poses the problem of transitioning between waveguide, coax cables and planar circuits. Moreover, Josephson amplifiers require auxiliary microwave components, like directional couplers and/or hybrids, that are sources of spurious losses and impedance mismatches that limit measurement efficiency and amplifier tunability. We have developed a new wireless architecture for these parametric amplifiers that eliminates superfluous microwave components and interconnects. This greatly simplifies their assembly and integration into experiments. We present an experimental realization of such a device operating in the $9-11$ GHz band with about $100$ MHz of amplitude gain-bandwidth product, on par with devices mounted in conventional sample holders. The simpler impedance environment presented to the amplifier also results in increased amplifier tunability. △ Less

Submitted 21 July, 2014; v1 submitted 19 April, 2014; originally announced April 2014.

Comments: 6 pages, 4 figures

Journal ref: Applied Physics Letters, 104, 232605 (2014)

Dynamically protected cat-qubits: a new paradigm for universal quantum computation

Authors: Mazyar Mirrahimi, Zaki Leghtas, Victor V. Albert, Steven Touzard, Robert J. Schoelkopf, Liang Jiang, Michel H. Devoret

Abstract: We present a new hardware-efficient paradigm for universal quantum computation which is based on encoding, protecting and manipulating quantum information in a quantum harmonic oscillator. This proposal exploits multi-photon driven dissipative processes to encode quantum information in logical bases composed of Schrödinger cat states. More precisely, we consider two schemes. In a first scheme, a t… ▽ More We present a new hardware-efficient paradigm for universal quantum computation which is based on encoding, protecting and manipulating quantum information in a quantum harmonic oscillator. This proposal exploits multi-photon driven dissipative processes to encode quantum information in logical bases composed of Schrödinger cat states. More precisely, we consider two schemes. In a first scheme, a two-photon driven dissipative process is used to stabilize a logical qubit basis of two-component Schrödinger cat states. While such a scheme ensures a protection of the logical qubit against the photon dephasing errors, the prominent error channel of single-photon loss induces bit-flip type errors that cannot be corrected. Therefore, we consider a second scheme based on a four-photon driven dissipative process which leads to the choice of four-component Schrödinger cat states as the logical qubit. Such a logical qubit can be protected against single-photon loss by continuous photon number parity measurements. Next, applying some specific Hamiltonians, we provide a set of universal quantum gates on the encoded qubits of each of the two schemes. In particular, we illustrate how these operations can be rendered fault-tolerant with respect to various decoherence channels of participating quantum systems. Finally, we also propose experimental schemes based on quantum superconducting circuits and inspired by methods used in Josephson parametric amplification, which should allow to achieve these driven dissipative processes along with the Hamiltonians ensuring the universal operations in an efficient manner. △ Less

Submitted 6 December, 2013; originally announced December 2013.

Comments: 28 pages, 11 figures

Journal ref: New J. Phys. 16, 045014 (2014)

Tracking Photon Jumps with Repeated Quantum Non-Demolition Parity Measurements

Authors: L. Sun, A. Petrenko, Z. Leghtas, B. Vlastakis, G. Kirchmair, K. M. Sliwa, A. Narla, M. Hatridge, S. Shankar, J. Blumoff, L. Frunzio, M. Mirrahimi, M. H. Devoret, R. J. Schoelkopf

Abstract: Quantum error correction (QEC) is required for a practical quantum computer because of the fragile nature of quantum information. In QEC, information is redundantly stored in a large Hilbert space and one or more observables must be monitored to reveal the occurrence of an error, without disturbing the information encoded in an unknown quantum state. Such observables, typically multi-qubit paritie… ▽ More Quantum error correction (QEC) is required for a practical quantum computer because of the fragile nature of quantum information. In QEC, information is redundantly stored in a large Hilbert space and one or more observables must be monitored to reveal the occurrence of an error, without disturbing the information encoded in an unknown quantum state. Such observables, typically multi-qubit parities such as <XXXX>, must correspond to a special symmetry property inherent to the encoding scheme. Measurements of these observables, or error syndromes, must also be performed in a quantum non-demolition (QND) way and faster than the rate at which errors occur. Previously, QND measurements of quantum jumps between energy eigenstates have been performed in systems such as trapped ions, electrons, cavity quantum electrodynamics (QED), nitrogen-vacancy (NV) centers, and superconducting qubits. So far, however, no fast and repeated monitoring of an error syndrome has been realized. Here, we track the quantum jumps of a possible error syndrome, the photon number parity of a microwave cavity, by mapping this property onto an ancilla qubit. This quantity is just the error syndrome required in a recently proposed scheme for a hardware-efficient protected quantum memory using Schrödinger cat states in a harmonic oscillator. We demonstrate the projective nature of this measurement onto a parity eigenspace by observing the collapse of a coherent state onto even or odd cat states. The measurement is fast compared to the cavity lifetime, has a high single-shot fidelity, and has a 99.8% probability per single measurement of leaving the parity unchanged. In combination with the deterministic encoding of quantum information in cat states realized earlier, our demonstrated QND parity tracking represents a significant step towards implementing an active system that extends the lifetime of a quantum bit. △ Less

Submitted 11 November, 2013; originally announced November 2013.

Comments: 6 pages with 4 figures for the main text, 14 pages with 9 figures for supplementary material

Journal ref: Nature 511, 444-448 (2014)

Reaching 10 ms single photon lifetimes for superconducting aluminum cavities

Authors: M. Reagor, Hanhee Paik, G. Catelani, L. Sun, C. Axline, E. Holland, I. M. Pop, N. A. Masluk, T. Brecht, L. Frunzio, M. H. Devoret, L. I. Glazman, R. J. Schoelkopf

Abstract: Three-dimensional microwave cavities have recently been combined with superconducting qubits in the circuit quantum electrodynamics (cQED) architecture. These cavities should have less sensitivity to dielectric and conductor losses at surfaces and interfaces, which currently limit the performance of planar resonators. We expect that significantly (>10^3) higher quality factors and longer lifetimes… ▽ More Three-dimensional microwave cavities have recently been combined with superconducting qubits in the circuit quantum electrodynamics (cQED) architecture. These cavities should have less sensitivity to dielectric and conductor losses at surfaces and interfaces, which currently limit the performance of planar resonators. We expect that significantly (>10^3) higher quality factors and longer lifetimes should be achievable for 3D structures. Motivated by this principle, we have reached internal quality factors greater than 0.5x10^9 and intrinsic lifetimes of 0.01 seconds for multiple aluminum superconducting cavity resonators at single photon energies and millikelvin temperatures. These improvements could enable long lived quantum memories with submicrosecond access times when strongly coupled to superconducting qubits. △ Less

Submitted 22 May, 2013; v1 submitted 18 February, 2013; originally announced February 2013.

Comments: 4 pages, 2 figures

Journal ref: Appl. Phys. Lett. 102, 192604 (2013)

Observation of quantum state collapse and revival due to the single-photon Kerr effect

Authors: Gerhard Kirchmair, Brian Vlastakis, Zaki Leghtas, Simon E. Nigg, Hanhee Paik, Eran Ginossar, Mazyar Mirrahimi, Luigi Frunzio, S. M. Girvin, R. J. Schoelkopf

Abstract: Photons are ideal carriers for quantum information as they can have a long coherence time and can be transmitted over long distances. These properties are a consequence of their weak interactions within a nearly linear medium. To create and manipulate nonclassical states of light, however, one requires a strong, nonlinear interaction at the single photon level. One approach to generate suitable in… ▽ More Photons are ideal carriers for quantum information as they can have a long coherence time and can be transmitted over long distances. These properties are a consequence of their weak interactions within a nearly linear medium. To create and manipulate nonclassical states of light, however, one requires a strong, nonlinear interaction at the single photon level. One approach to generate suitable interactions is to couple photons to atoms, as in the strong coupling regime of cavity QED systems. In these systems, however, one only indirectly controls the quantum state of the light by manipulating the atoms. A direct photon-photon interaction occurs in so-called Kerr media, which typically induce only weak nonlinearity at the cost of significant loss. So far, it has not been possible to reach the single-photon Kerr regime, where the interaction strength between individual photons exceeds the loss rate. Here, using a 3D circuit QED architecture, we engineer an artificial Kerr medium which enters this regime and allows the observation of new quantum effects. We realize a Gedankenexperiment proposed by Yurke and Stoler, in which the collapse and revival of a coherent state can be observed. This time evolution is a consequence of the quantization of the light field in the cavity and the nonlinear interaction between individual photons. During this evolution non-classical superpositions of coherent states, i.e. multi-component Schroedinger cat states, are formed. We visualize this evolution by measuring the Husimi Q-function and confirm the non-classical properties of these transient states by Wigner tomography. The single-photon Kerr effect could be employed in QND measurement of photons, single photon generation, autonomous quantum feedback schemes and quantum logic operations. △ Less

Submitted 9 November, 2012; originally announced November 2012.

Comments: 6 pages, 4 figures, 5 pages supplementary Material, 3 figures

Journal ref: Nature 495, 205 (2013)

Demonstrating a Driven Reset Protocol of a Superconducting Qubit

Authors: K. Geerlings, Z. Leghtas, I. M. Pop, S. Shankar, L. Frunzio, R. J. Schoelkopf, M. Mirrahimi, M. H. Devoret

Abstract: Qubit reset is crucial at the start of and during quantum information algorithms. We present the experimental demonstration of a practical method to force qubits into their ground state, based on driving certain qubit and cavity transitions. Our protocol, called the double drive reset of population is tested on a superconducting transmon qubit in a three-dimensional cavity. Using a new method for… ▽ More Qubit reset is crucial at the start of and during quantum information algorithms. We present the experimental demonstration of a practical method to force qubits into their ground state, based on driving certain qubit and cavity transitions. Our protocol, called the double drive reset of population is tested on a superconducting transmon qubit in a three-dimensional cavity. Using a new method for measuring population, we show that we can prepare the ground state with a fidelity of at least 99.5 % in less than 3 microseconds; faster times and higher fidelity are predicted upon parameter optimization. △ Less

Submitted 25 March, 2013; v1 submitted 2 November, 2012; originally announced November 2012.

Comments: 5 pages, 4 figures

Journal ref: Phys. Rev. Lett. 110, 120501 (2013)

Decoherence of superconducting qubits caused by quasiparticle tunneling

Authors: G. Catelani, Simon E. Nigg, S. M. Girvin, R. J. Schoelkopf, L. I. Glazman

Abstract: In superconducting qubits, the interaction of the qubit degree of freedom with quasiparticles defines a fundamental limitation for the qubit coherence. We develop a theory of the pure dephasing rate Γ_φ caused by quasiparticles tunneling through a Josephson junction and of the inhomogeneous broadening due to changes in the occupations of Andreev states in the junction. To estimate Γ_φ, we derive a… ▽ More In superconducting qubits, the interaction of the qubit degree of freedom with quasiparticles defines a fundamental limitation for the qubit coherence. We develop a theory of the pure dephasing rate Γ_φ caused by quasiparticles tunneling through a Josephson junction and of the inhomogeneous broadening due to changes in the occupations of Andreev states in the junction. To estimate Γ_φ, we derive a master equation for the qubit dynamics. The tunneling rate of free quasiparticles is enhanced by their large density of states at energies close to the superconducting gap. Nevertheless, we find that Γ_φ is small compared to the rates determined by extrinsic factors in most of the current qubit designs (phase and flux qubits, transmon, fluxonium). The split transmon, in which a single junction is replaced by a SQUID loop, represents an exception that could make possible the measurement of Γ_φ. Fluctuations of the qubit frequency leading to inhomogeneous broadening may be caused by the fluctuations in the occupation numbers of the Andreev states associated with a phase-biased Josephson junction. This mechanism may be revealed in qubits with small-area junctions, since the smallest relative change in frequency it causes is of the order of the inverse number of transmission channels in the junction. △ Less

Submitted 30 July, 2012; originally announced July 2012.

Comments: 18 pages, 2 figures

Journal ref: Phys. Rev. B 86, 184514 (2012)

Photon Shot Noise Dephasing in the Strong-Dispersive Limit of Circuit QED

Authors: A. P. Sears, A. Petrenko, G. Catelani, L. Sun, Hanhee Paik, G. Kirchmair, L. Frunzio, L. I. Glazman, S. M. Girvin, R. J. Schoelkopf

Abstract: We study the photon shot noise dephasing of a superconducting transmon qubit in the strong-dispersive limit, due to the coupling of the qubit to its readout cavity. As each random arrival or departure of a photon is expected to completely dephase the qubit, we can control the rate at which the qubit experiences dephasing events by varying \textit{in situ} the cavity mode population and decay rate.… ▽ More We study the photon shot noise dephasing of a superconducting transmon qubit in the strong-dispersive limit, due to the coupling of the qubit to its readout cavity. As each random arrival or departure of a photon is expected to completely dephase the qubit, we can control the rate at which the qubit experiences dephasing events by varying \textit{in situ} the cavity mode population and decay rate. This allows us to verify a pure dephasing mechanism that matches theoretical predictions, and in fact explains the increased dephasing seen in recent transmon experiments as a function of cryostat temperature. We investigate photon dynamics in this limit and observe large increases in coherence times as the cavity is decoupled from the environment. Our experiments suggest that the intrinsic coherence of small Josephson junctions, when corrected with a single Hahn echo, is greater than several hundred microseconds. △ Less

Submitted 6 June, 2012; originally announced June 2012.

Comments: 5 pages, 4 figures; includes Supporting Online Material of 6 pages with 5 figures

Journal ref: Phys. Rev. B 86, 180504(R) (2012)

Improving the Quality Factor of Microwave Compact Resonators by Optimizing their Geometrical Parameters

Authors: K. Geerlings, S. Shankar, E. Edwards, L. Frunzio, R. J. Schoelkopf, M. H. Devoret

Abstract: Applications in quantum information processing and photon detectors are stimulating a race to produce the highest possible quality factor on-chip superconducting microwave resonators. We have tested the surface-dominated loss hypothesis by systematically studying the role of geometrical parameters on the internal quality factors of compact resonators patterned in Nb on sapphire. Their single-photo… ▽ More Applications in quantum information processing and photon detectors are stimulating a race to produce the highest possible quality factor on-chip superconducting microwave resonators. We have tested the surface-dominated loss hypothesis by systematically studying the role of geometrical parameters on the internal quality factors of compact resonators patterned in Nb on sapphire. Their single-photon internal quality factors were found to increase with the distance between capacitor fingers, the width of the capacitor fingers, and the impedance of the resonator. Quality factors were improved from 210,000 to 500,000 at T = 200 mK. All of these results are consistent with our starting hypothesis. △ Less

Submitted 5 June, 2012; v1 submitted 3 April, 2012; originally announced April 2012.

Comments: 8 pages, 4 figures

Journal ref: Appl. Phys. Lett. 100, 192601 (2012)

Measurements of Quasiparticle Tunneling Dynamics in a Bandgap-Engineered Transmon Qubit

Authors: L. Sun, L. DiCarlo, M. D. Reed, G. Catelani, Lev S. Bishop, D. I. Schuster, B. R. Johnson, Ge A. Yang, L. Frunzio, L. I. Glazman, M. H. Devoret, R. J. Schoelkopf

Abstract: We have engineered the bandgap profile of transmon qubits by combining oxygen-doped Al for tunnel junction electrodes and clean Al as quasiparticle traps to investigate energy relaxation due to quasiparticle tunneling. The relaxation time $T_1$ of the qubits is shown to be insensitive to this bandgap engineering. Operating at relatively low $E_J/E_C$ makes the transmon transition frequency distinc… ▽ More We have engineered the bandgap profile of transmon qubits by combining oxygen-doped Al for tunnel junction electrodes and clean Al as quasiparticle traps to investigate energy relaxation due to quasiparticle tunneling. The relaxation time $T_1$ of the qubits is shown to be insensitive to this bandgap engineering. Operating at relatively low $E_J/E_C$ makes the transmon transition frequency distinctly dependent on the charge parity, allowing us to detect the quasiparticles tunneling across the qubit junction. Quasiparticle kinetics have been studied by monitoring the frequency switching due to even/odd parity change in real time. It shows the switching time is faster than 10 $μ$s, indicating quasiparticle-induced relaxation has to be reduced to achieve $T_1$ much longer than 100 $μ$s. △ Less

Submitted 12 December, 2011; originally announced December 2011.

Comments: 11 pages, 8 figures

Journal ref: Phys. Rev. Lett. 108, 230509 (2012)

Realization of Three-Qubit Quantum Error Correction with Superconducting Circuits

Authors: M. D. Reed, L. DiCarlo, S. E. Nigg, L. Sun, L. Frunzio, S. M. Girvin, R. J. Schoelkopf

Abstract: Quantum computers promise to solve certain problems exponentially faster than possible classically but are challenging to build because of their increased susceptibility to errors. Remarkably, however, it is possible to detect and correct errors without destroying coherence by using quantum error correcting codes [1]. The simplest of these are the three-qubit codes, which map a one-qubit state to… ▽ More Quantum computers promise to solve certain problems exponentially faster than possible classically but are challenging to build because of their increased susceptibility to errors. Remarkably, however, it is possible to detect and correct errors without destroying coherence by using quantum error correcting codes [1]. The simplest of these are the three-qubit codes, which map a one-qubit state to an entangled three-qubit state and can correct any single phase-flip or bit-flip error of one of the three qubits, depending on the code used [2]. Here we demonstrate both codes in a superconducting circuit by encoding a quantum state as previously shown [3,4], inducing errors on all three qubits with some probability, and decoding the error syndrome by reversing the encoding process. This syndrome is then used as the input to a three-qubit gate which corrects the primary qubit if it was flipped. As the code can recover from a single error on any qubit, the fidelity of this process should decrease only quadratically with error probability. We implement the correcting three-qubit gate, known as a conditional-conditional NOT (CCNot) or Toffoli gate, using an interaction with the third excited state of a single qubit, in 63 ns. We find 85\pm1% fidelity to the expected classical action of this gate and 78\pm1% fidelity to the ideal quantum process matrix. Using it, we perform a single pass of both quantum bit- and phase-flip error correction with 76\pm0.5% process fidelity and demonstrate the predicted first-order insensitivity to errors. Concatenating these two codes and performing them on a nine-qubit device would correct arbitrary single-qubit errors. When combined with recent advances in superconducting qubit coherence times [5,6], this may lead to scalable quantum technology. △ Less

Submitted 22 September, 2011; originally announced September 2011.

Comments: 10 pages, 7 figures

Journal ref: Nature 482, 382-385 (2012)

Relaxation and frequency shifts induced by quasiparticles in superconducting qubits

Authors: G. Catelani, R. J. Schoelkopf, M. H. Devoret, L. I. Glazman

Abstract: As low-loss non-linear elements, Josephson junctions are the building blocks of superconducting qubits. The interaction of the qubit degree of freedom with the quasiparticles tunneling through the junction represent an intrinsic relaxation mechanism. We develop a general theory for the qubit decay rate induced by quasiparticles, and we study its dependence on the magnetic flux used to tune the qub… ▽ More As low-loss non-linear elements, Josephson junctions are the building blocks of superconducting qubits. The interaction of the qubit degree of freedom with the quasiparticles tunneling through the junction represent an intrinsic relaxation mechanism. We develop a general theory for the qubit decay rate induced by quasiparticles, and we study its dependence on the magnetic flux used to tune the qubit properties in devices such as the phase and flux qubits, the split transmon, and the fluxonium. Our estimates for the decay rate apply to both thermal equilibrium and non-equilibrium quasiparticles. We propose measuring the rate in a split transmon to obtain information on the possible non-equilibrium quasiparticle distribution. We also derive expressions for the shift in qubit frequency in the presence of quasiparticles. △ Less

Submitted 4 June, 2011; originally announced June 2011.

Comments: 25 pages, 6 figures

Journal ref: Phys. Rev. B 84, 064517 (2011)

Observation of high coherence in Josephson junction qubits measured in a three-dimensional circuit QED architecture

Authors: Hanhee Paik, D. I. Schuster, Lev S. Bishop, G. Kirchmair, G. Catelani, A. P. Sears, B. R. Johnson, M. J. Reagor, L. Frunzio, L. Glazman, S. M. Girvin, M. H. Devoret, R. J. Schoelkopf

Abstract: Superconducting quantum circuits based on Josephson junctions have made rapid progress in demonstrating quantum behavior and scalability. However, the future prospects ultimately depend upon the intrinsic coherence of Josephson junctions, and whether superconducting qubits can be adequately isolated from their environment. We introduce a new architecture for superconducting quantum circuits employ… ▽ More Superconducting quantum circuits based on Josephson junctions have made rapid progress in demonstrating quantum behavior and scalability. However, the future prospects ultimately depend upon the intrinsic coherence of Josephson junctions, and whether superconducting qubits can be adequately isolated from their environment. We introduce a new architecture for superconducting quantum circuits employing a three dimensional resonator that suppresses qubit decoherence while maintaining sufficient coupling to the control signal. With the new architecture, we demonstrate that Josephson junction qubits are highly coherent, with $T_2 \sim 10 μ$s to $20 μ$s without the use of spin echo, and highly stable, showing no evidence for $1/f$ critical current noise. These results suggest that the overall quality of Josephson junctions in these qubits will allow error rates of a few $10^{-4}$, approaching the error correction threshold. △ Less

Submitted 1 November, 2011; v1 submitted 23 May, 2011; originally announced May 2011.

Comments: 5 pages, 3 figures, 1 table. Accepted to Phys. Rev. Lett

Journal ref: Phys. Rev. Lett. 107, 240501 (2011)

Quasiparticle relaxation of superconducting qubits in the presence of flux

Authors: G. Catelani, Jens Koch, L. Frunzio, R. J. Schoelkopf, M. H. Devoret, L. I. Glazman

Abstract: Quasiparticle tunneling across a Josephson junction sets a limit for the lifetime of a superconducting qubit state. We develop a general theory of the corresponding decay rate in a qubit controlled by a magnetic flux. The flux affects quasiparticles tunneling amplitudes, thus making the decay rate flux-dependent. The theory is applicable for an arbitrary quasiparticle distribution. It provides est… ▽ More Quasiparticle tunneling across a Josephson junction sets a limit for the lifetime of a superconducting qubit state. We develop a general theory of the corresponding decay rate in a qubit controlled by a magnetic flux. The flux affects quasiparticles tunneling amplitudes, thus making the decay rate flux-dependent. The theory is applicable for an arbitrary quasiparticle distribution. It provides estimates for the rates in practically important quantum circuits and also offers a new way of measuring the phase-dependent admittance of a Josephson junction. △ Less

Submitted 21 January, 2011; v1 submitted 6 January, 2011; originally announced January 2011.

Comments: 4.5 pages, 1 figure; minor changes to text & references, to appear in Phys. Rev. Lett

Journal ref: Phys. Rev. Lett. 106, 077002 (2011)

High cooperativity coupling of electron-spin ensembles to superconducting cavities

Authors: D. I. Schuster, A. P. Sears, E. Ginossar, L. DiCarlo, L. Frunzio, J. J. L. Morton, H. Wu, G. A. D. Briggs, R. J. Schoelkopf

Abstract: Electron spins in solids are promising candidates for quantum memories for superconducting qubits because they can have long coherence times, large collective couplings, and many quantum bits can be encoded into the spin-waves of a single ensemble. We demonstrate the coupling of electron spin ensembles to a superconducting transmission-line resonator at coupling strengths greatly exceeding the cav… ▽ More Electron spins in solids are promising candidates for quantum memories for superconducting qubits because they can have long coherence times, large collective couplings, and many quantum bits can be encoded into the spin-waves of a single ensemble. We demonstrate the coupling of electron spin ensembles to a superconducting transmission-line resonator at coupling strengths greatly exceeding the cavity decay rate and comparable to spin linewidth. We also use the enhanced coupling afforded by the small cross-section of the transmission line to perform broadband spectroscopy of ruby at millikelvin temperatures at low powers. In addition, we observe hyperfine structure in diamond P1 centers and time domain saturation-relaxation of the spins. △ Less

Submitted 1 June, 2010; originally announced June 2010.

Comments: 4pgs, 4 figures

Implementing optimal control pulse shaping for improved single-qubit gates

Authors: J. M. Chow, L. DiCarlo, J. M. Gambetta, F. Motzoi, L. Frunzio, S. M. Girvin, R. J. Schoelkopf

Abstract: We employ pulse shaping to abate single-qubit gate errors arising from the weak anharmonicity of transmon superconducting qubits. By applying shaped pulses to both quadratures of rotation, a phase error induced by the presence of higher levels is corrected. Using a derivative of the control on the quadrature channel, we are able to remove the effect of the anharmonic levels for multiple qubits cou… ▽ More We employ pulse shaping to abate single-qubit gate errors arising from the weak anharmonicity of transmon superconducting qubits. By applying shaped pulses to both quadratures of rotation, a phase error induced by the presence of higher levels is corrected. Using a derivative of the control on the quadrature channel, we are able to remove the effect of the anharmonic levels for multiple qubits coupled to a microwave resonator. Randomized benchmarking is used to quantify the average error per gate, achieving a minimum of 0.007+/-0.005 using 4 ns-wide pulse. △ Less

Submitted 7 May, 2010; originally announced May 2010.

Comments: 4 pages, 4 figures

Journal ref: Phys. Rev. A 82, 040305(R) (2010)

Preparation and Measurement of Three-Qubit Entanglement in a Superconducting Circuit

Authors: L. DiCarlo, M. D. Reed, L. Sun, B. R. Johnson, J. M. Chow, J. M. Gambetta, L. Frunzio, S. M. Girvin, M. H. Devoret, R. J. Schoelkopf

Abstract: Traditionally, quantum entanglement has played a central role in foundational discussions of quantum mechanics. The measurement of correlations between entangled particles can exhibit results at odds with classical behavior. These discrepancies increase exponentially with the number of entangled particles. When entanglement is extended from just two quantum bits (qubits) to three, the incompatibi… ▽ More Traditionally, quantum entanglement has played a central role in foundational discussions of quantum mechanics. The measurement of correlations between entangled particles can exhibit results at odds with classical behavior. These discrepancies increase exponentially with the number of entangled particles. When entanglement is extended from just two quantum bits (qubits) to three, the incompatibilities between classical and quantum correlation properties can change from a violation of inequalities involving statistical averages to sign differences in deterministic observations. With the ample confirmation of quantum mechanical predictions by experiments, entanglement has evolved from a philosophical conundrum to a key resource for quantum-based technologies, like quantum cryptography and computation. In particular, maximal entanglement of more than two qubits is crucial to the implementation of quantum error correction protocols. While entanglement of up to 3, 5, and 8 qubits has been demonstrated among spins, photons, and ions, respectively, entanglement in engineered solid-state systems has been limited to two qubits. Here, we demonstrate three-qubit entanglement in a superconducting circuit, creating Greenberger-Horne-Zeilinger (GHZ) states with fidelity of 88%, measured with quantum state tomography. Several entanglement witnesses show violation of bi-separable bounds by 830\pm80%. Our entangling sequence realizes the first step of basic quantum error correction, namely the encoding of a logical qubit into a manifold of GHZ-like states using a repetition code. The integration of encoding, decoding and error-correcting steps in a feedback loop will be the next milestone for quantum computing with integrated circuits. △ Less

Submitted 25 April, 2010; originally announced April 2010.

Comments: 7 pages, 4 figures, and Supplementary Information (4 figures).

Journal ref: Nature 467, 574-578 (2010)

High-Fidelity Readout in Circuit Quantum Electrodynamics Using the Jaynes-Cummings Nonlinearity

Authors: M. D. Reed, L. DiCarlo, B. R. Johnson, L. Sun, D. I. Schuster, L. Frunzio, R. J. Schoelkopf

Abstract: We demonstrate a qubit readout scheme that exploits the Jaynes-Cummings nonlinearity of a superconducting cavity coupled to transmon qubits. We find that in the strongly-driven dispersive regime of this system, there is the unexpected onset of a high-transmission "bright" state at a critical power which depends sensitively on the initial qubit state. A simple and robust measurement protocol exploi… ▽ More We demonstrate a qubit readout scheme that exploits the Jaynes-Cummings nonlinearity of a superconducting cavity coupled to transmon qubits. We find that in the strongly-driven dispersive regime of this system, there is the unexpected onset of a high-transmission "bright" state at a critical power which depends sensitively on the initial qubit state. A simple and robust measurement protocol exploiting this effect achieves a single-shot fidelity of 87% using a conventional sample design and experimental setup, and at least 61% fidelity to joint correlations of three qubits. △ Less

Submitted 19 October, 2010; v1 submitted 25 April, 2010; originally announced April 2010.

Comments: 5 pages, 4 figures

Journal ref: Phys. Rev. Lett. 105, 173601 (2010)

Quantum Non-demolition Detection of Single Microwave Photons in a Circuit

Authors: B. R. Johnson, M. D. Reed, A. A. Houck, D. I. Schuster, Lev S. Bishop, E. Ginossar, J. M. Gambetta, L. DiCarlo, L. Frunzio, S. M. Girvin, R. J. Schoelkopf

Abstract: Thorough control of quantum measurement is key to the development of quantum information technologies. Many measurements are destructive, removing more information from the system than they obtain. Quantum non-demolition (QND) measurements allow repeated measurements that give the same eigenvalue. They could be used for several quantum information processing tasks such as error correction, prepara… ▽ More Thorough control of quantum measurement is key to the development of quantum information technologies. Many measurements are destructive, removing more information from the system than they obtain. Quantum non-demolition (QND) measurements allow repeated measurements that give the same eigenvalue. They could be used for several quantum information processing tasks such as error correction, preparation by measurement, and one-way quantum computing. Achieving QND measurements of photons is especially challenging because the detector must be completely transparent to the photons while still acquiring information about them. Recent progress in manipulating microwave photons in superconducting circuits has increased demand for a QND detector which operates in the gigahertz frequency range. Here we demonstrate a QND detection scheme which measures the number of photons inside a high quality-factor microwave cavity on a chip. This scheme maps a photon number onto a qubit state in a single-shot via qubit-photon logic gates. We verify the operation of the device by analyzing the average correlations of repeated measurements, and show that it is 90% QND. It differs from previously reported detectors because its sensitivity is strongly selective to chosen photon number states. This scheme could be used to monitor the state of a photon-based memory in a quantum computer. △ Less

Submitted 13 March, 2010; originally announced March 2010.

Comments: 5 pages, 4 figures, includes supplementary material

Journal ref: Nature Physics 6, 663 - 667 (2010)