-
Microstructure evolution and mechanical behavior of Fe-Mn-Al-C low-density steel upon aging
Authors:
Alexandros Banis,
Andrea Gomez,
Vitaliy Bliznuk,
Aniruddha Dutta,
Ilchat Sabirov,
Roumen H. Petrov
Abstract:
This study focuses on the microstructure's evolution upon different aging conditions of a high-strength low-density steel with a composition of Fe-28Mn-9Al-1C. The steel is hot-rolled, subsequently quenched without any solution treatment, and then aged under different conditions. The microstructure of the samples was studied by means of Scanning Electron Microscopy, Electron Backscatter Diffractio…
▽ More
This study focuses on the microstructure's evolution upon different aging conditions of a high-strength low-density steel with a composition of Fe-28Mn-9Al-1C. The steel is hot-rolled, subsequently quenched without any solution treatment, and then aged under different conditions. The microstructure of the samples was studied by means of Scanning Electron Microscopy, Electron Backscatter Diffraction, and Transmission Electron Microscopy. The aging treatment leads to the formation of an ordered face-centered cubic L12 phase named k-carbide. This study aims to characterize the formation and growth of these k-carbides qualitatively and quantitatively under different aging conditions. Then, an effort is made to relate the fraction and size of this phase with the tensile properties of the steel to determine the optimal aging conditions that will lead to a good combination of strength and ductility. It has been found that the k-carbides start to form intragranularly through concentration fluctuations of aluminum and manganese inside the austenite grain. Then, with the process of spinodal decomposition, they grow in size coherently with the matrix. During this process, the strength and hardness of the steel increase while maintaining a relatively high elongation. The best combination of high strength and ductility was achieved at the aging condition of 8 h at 550 degrees Celsius with an ultimate tensile strength up to 1157 MPa and total elongation of 51%. Increasing the aging temperature and time, k-carbides start to form intergranularly, lose their coherency with the matrix and severely compromise the hardness and strength. The shearing of the carbides during deformation is also studied.
△ Less
Submitted 3 May, 2023; v1 submitted 30 April, 2023;
originally announced May 2023.
-
Effect of alloying and microstructure on formability of advanced high-strength steels processed via quenching and partitioning
Authors:
P. Xia,
F. Vercruysse,
C. Celada-Casero,
P. Verleysen,
R. H. Petrov,
I. Sabirov,
J. M. Molina-Aldareguia,
A. Smith,
B. Linke,
R. Thiessen,
D. Frometa,
S. Parareda,
A. Lara
Abstract:
The article focuses on the effect of alloying and microstructure on formability of advanced high strength steels (AHSSs) processed via quenching and partitioning (Q&P). Three different Q&P steels with different combination of alloying elements and volume fraction of retained austenite are subjected to uniaxial tensile and Nakajima testing. Tensile mechanical properties are determined, and the form…
▽ More
The article focuses on the effect of alloying and microstructure on formability of advanced high strength steels (AHSSs) processed via quenching and partitioning (Q&P). Three different Q&P steels with different combination of alloying elements and volume fraction of retained austenite are subjected to uniaxial tensile and Nakajima testing. Tensile mechanical properties are determined, and the forming limit diagrams (FLDs) are plotted. Microstructure of the tested samples is analyzed, and dramatic reduction of retained austenite fraction is detected. It is demonstrated that all steels are able to accumulate much higher amount of plastic strain when tested using Nakajima method. The observed phenomenon is related to the multiaxial stress state and strain gradients through the sheet thickness resulting in a fast transformation of retained austenite, as well as the ability of the tempered martensitic matrix to accumulate plastic strain. Surprisingly, a Q&P steel with the highest volume fraction of retained austenite and highest tensile ductility shows the lowest formability among studied grades. The latter observation is related to the highest sum of fractions of initial fresh martensite and stress/strain induced martensite promoting formation of microcracks. Their role and ability of tempered martensitic matrix to accumulate plastic deformation during forming of Q&P steels is discussed.
△ Less
Submitted 19 October, 2021;
originally announced October 2021.
-
A new physical simulation tool to predict the interface of dissimilar aluminum to steel welds performed by Friction Melt Bonding
Authors:
T. Sapanathan,
N. Jimenez-Mena,
I. Sabirov,
M. A. Monclus,
J. M. Molina-Aldareguia,
P. Xia,
L. Zhao,
A. Simar
Abstract:
Optimization of the intermetallic layer thickness and the suppression of interfacial defects are key elements to improve the load bearing capacity of dissimilar joints. However, till date we do not have a systematic tool to investigate the dissimilar joints and the intermetallic properties produced by a welding condition. Friction Melt Bonding (FMB) is a recently developed technique for joining di…
▽ More
Optimization of the intermetallic layer thickness and the suppression of interfacial defects are key elements to improve the load bearing capacity of dissimilar joints. However, till date we do not have a systematic tool to investigate the dissimilar joints and the intermetallic properties produced by a welding condition. Friction Melt Bonding (FMB) is a recently developed technique for joining dissimilar metals that also does not exempt to these challenges. The FMB of DP980 and Al6061-T6 is investigated using a new physical simulation tool, based on Gleeble thermo-mechanical simulator, to understand the effect of individual parameter on the intermetallic formation. The proposed method demonstrates its capability in reproducing the intermetallic characteristics, including the thickness of intermetallic bonding layer, the morphology and texture of its constituents (Fe2Al5 and Fe4Al13), as well as their nanohardness and reduced modulus. The advantages of physical simulation tool can enable novel developing routes for the development of dissimilar metal joining processes and facilitate to reach the requiring load bearing capacity of the joints.
△ Less
Submitted 1 April, 2021;
originally announced April 2021.
-
Failure of refractory masonry material under monotonic and cyclic loading: crack propagation analysis
Authors:
K. Andreev,
Y. Yin,
B. Luchini,
I. Sabirov
Abstract:
Refractory masonry (refractories) is exposed to in-service loads of different types. To rationalise the masonry design and failure analysis, differences of failure under cyclic and monotonic loading were studied. For samples of silica refractories tested in wedge splitting set-up global failure parameters and crack trajectories were assessed. Under cyclic loading, higher fracture energy and lower…
▽ More
Refractory masonry (refractories) is exposed to in-service loads of different types. To rationalise the masonry design and failure analysis, differences of failure under cyclic and monotonic loading were studied. For samples of silica refractories tested in wedge splitting set-up global failure parameters and crack trajectories were assessed. Under cyclic loading, higher fracture energy and lower brittleness at failure were seen. Cracks of different modes had similar non-linearity and branching. However, the size and microstructural characteristics of the fracture process zone was different. In addition, higher energy dissipation during cyclic loading is promoted by repetitive friction events along the crack trajectory.
△ Less
Submitted 27 July, 2021; v1 submitted 1 April, 2021;
originally announced April 2021.
-
High temperature in situ SEM assessment followed by ex situ AFM and EBSD investigation of the nucleation and early growth stages of Fe-Al intermetallics
Authors:
T. Sapanathan,
I. Sabirov,
P. Xia,
M. A. Monclus,
J. M. Molina-Aldareguia,
P. J. Jacques,
A. Simar
Abstract:
A dedicated in situ heating setup in a scanning electron microscope (SEM) followed by an ex situ atomic force microscopy (AFM) and electron backscatter diffraction (EBSD) is used to characterize the nucleation and early growth stages of Fe-Al intermetallics (IMs) at 596 °C. A location tracking is used to interpret further characterization. Ex situ AFM observations reveal a slight shrinkage and out…
▽ More
A dedicated in situ heating setup in a scanning electron microscope (SEM) followed by an ex situ atomic force microscopy (AFM) and electron backscatter diffraction (EBSD) is used to characterize the nucleation and early growth stages of Fe-Al intermetallics (IMs) at 596 °C. A location tracking is used to interpret further characterization. Ex situ AFM observations reveal a slight shrinkage and out of plane protrusion of the IM at the onset of IM nucleation followed by directional growth. The formed interfacial IM compounds were identified by ex situ EBSD. It is now clearly demonstrated that the θ-phase nucleates first prior to the diffusion-controlled growth of the η-phase. The θ-phase prevails the intermetallic layer.
△ Less
Submitted 31 March, 2021;
originally announced March 2021.
-
The sensitivity of the microstructure and properties to the peak temperature in an ultrafast heat treated low carbon-steel
Authors:
M. A. Valdes-Tabernero,
A. Kumar,
R. H. Petrov,
M. A. Monclus,
. M. Molina-Aldareguia,
I. Sabirov
Abstract:
In this work, we investigate the sensitivity of the microstructure and mechanical properties of an ultrafast heat treated low carbon-steel to the peak temperature. In all studied cases, the steel was heated within the intercritical temperature range (i.e. between the AC1 and AC3 temperatures). Both the peak temperature and soaking time were varied, and their effect on the size, the fraction of ind…
▽ More
In this work, we investigate the sensitivity of the microstructure and mechanical properties of an ultrafast heat treated low carbon-steel to the peak temperature. In all studied cases, the steel was heated within the intercritical temperature range (i.e. between the AC1 and AC3 temperatures). Both the peak temperature and soaking time were varied, and their effect on the size, the fraction of individual microstructural constituents and their tensile mechanical response were investigated. It is shown that the increasing peak temperature and soaking time promote austenite formation and recrystallization processes in the ferritic matrix. The highest nanohardness is shown by martensitic grains, while recovered ferrite demonstrated slightly higher nanohardness compared to recrystallized ferrite. The applied heat treatment parameters have strong effect on the nanohardness of martensite, whereas nanohardness of ferrite microconstituents is not sensitive to variation of the peak temperature and soaking time. The non-recrystallized ferrite is harder than its recrystallized counterpart due to the higher dislocation density of the former. Increasing peak temperatures promote strengthening in the material at the expense of its ductility mainly due to increased martensite fraction. The steel demonstrates enhanced strain hardening ability independently of the peak temperature. Analysis of the experimental results showed that the industrial processing window of +- 10 oC may lead to some heterogeneity of the local microstructure in the ultrafast heat treated sheets. However, the latter should not have any negative effect on the overall mechanical behavior of the ultrafast heat treated steel sheets on the macro-scale.
△ Less
Submitted 18 January, 2020;
originally announced January 2020.
-
The effect of heating rate and soaking time on microstructure of an advanced high strength steel
Authors:
M. A. Valdes-Tabernero,
C. Celada-Casero,
I. Sabirov,
A. Kumar,
R. H. Petrov
Abstract:
This work focuses on the effect of soaking time on the microstructure during ultrafast heat treatment of a 50% cold rolled low carbon steel with initial ferritic-pearlitic microstructure. Dilatometry analysis was used to estimate the effect of heating rate on the phase transformation temperatures and to select an appropriate inter-critical temperature for final heat treatments. A thorough qualitat…
▽ More
This work focuses on the effect of soaking time on the microstructure during ultrafast heat treatment of a 50% cold rolled low carbon steel with initial ferritic-pearlitic microstructure. Dilatometry analysis was used to estimate the effect of heating rate on the phase transformation temperatures and to select an appropriate inter-critical temperature for final heat treatments. A thorough qualitative and quantitative microstructural characterization of the heat treated samples is performed using a wide range of characterization techniques. A complex multiphase, hierarchical microstructure consisting of ferritic matrix with embedded martensite and retained austenite is formed after all applied heat treatments. In turn, the ferritic matrix contains recrystallized and non-recrystallized grains. It is demonstrated that the ultrafast heating generally results in finer microstructure compared to the conventional heating independently on the soaking time. There is a significant effect of the soaking time on the volume fraction of martensite of the ultrafast heated material, while in the samples heated with conventional heating rate it remains relatively unchanged during soaking. Recrystallization, recovery and phase transformations occurring during soaking are discussed with respect to the applied heating rate.
△ Less
Submitted 30 July, 2019;
originally announced July 2019.
-
A multidisciplinary approach to study precipitation kinetics and hardening in an Al-4Cu (wt. %) alloy
Authors:
A. Rodríguez-Veiga,
B. Bellón,
I. Papadimitriou,
G. Esteban-Manzanares,
I. Sabirov,
J. Llorca
Abstract:
A multidisciplinary approach is presented to analyse the precipitation process in a model Al-Cu alloy. Although this topic has been extensively studied in the past, most of the investigations are focussed either on transmission electron microscopy or on thermal analysis of the processes. The information obtained from these techniques cannot, however, provide a coherent picture of all the complex t…
▽ More
A multidisciplinary approach is presented to analyse the precipitation process in a model Al-Cu alloy. Although this topic has been extensively studied in the past, most of the investigations are focussed either on transmission electron microscopy or on thermal analysis of the processes. The information obtained from these techniques cannot, however, provide a coherent picture of all the complex transformations that take place during decomposition of supersaturated solid solution. Thermal analysis, high resolution dilatometry, (high resolution) transmission electron microscopy and density functional calculations are combined to study precipitation kinetics, interfacial energies, and the effect of second phase precipitates on the mechanical strength of the alloy. Data on both the coherent and semi-coherent orientations of the θ"/Al interface are reported for the first time. The combination of the different characterization and modelling techniques provides a detailed picture of the precipitation phenomena that take place during aging and of the different contributions to the strength of the alloy. This strategy can be used to analyse and design more complex alloys.
△ Less
Submitted 25 April, 2018;
originally announced April 2018.
