-
Superconducting properties of thin film $\mathrm{Nb_{1-x}Ti_xN}$ studied via the NMR of implanted $^8$Li
Authors:
Md Asaduzzaman,
Ryan M. L. McFadden,
Edward Thoeng,
Yasmine Kalboussi,
Ivana Curci,
Thomas Proslier,
Sarah R. Dunsiger,
W. Andrew MacFarlane,
Gerald D. Morris,
Ruohong Li,
John O. Ticknor,
Robert E. Laxdal,
Tobias Junginger
Abstract:
We report measurements of the normal-state and superconducting properties of thin-film $\mathrm{Nb_{1-x}Ti_xN}$ using $^{8}$Li $β$-detected nuclear magnetic resonance ($β$-NMR). In these experiments, radioactive $^{8}$Li$^{+}$ probes were implanted $\sim21$ nm below the surface of a $\mathrm{Nb_{1-x}Ti_xN}$(91 nm) film in $\mathrm{Nb_{0.75}Ti_{0.25}N}$(91 nm)/AlN(4 nm)/Nb and its NMR response reco…
▽ More
We report measurements of the normal-state and superconducting properties of thin-film $\mathrm{Nb_{1-x}Ti_xN}$ using $^{8}$Li $β$-detected nuclear magnetic resonance ($β$-NMR). In these experiments, radioactive $^{8}$Li$^{+}$ probes were implanted $\sim21$ nm below the surface of a $\mathrm{Nb_{1-x}Ti_xN}$(91 nm) film in $\mathrm{Nb_{0.75}Ti_{0.25}N}$(91 nm)/AlN(4 nm)/Nb and its NMR response recorded (via $^{8}$Li's $β$-emissions) between 4.6 K and 270 K in a 4.1 T field applied normal to its surface. Resonance measurements reveal wide, symmetric lineshapes at all temperatures, with significant additional broadening below the film's superconducting transition temperature $T_\mathrm{c}(0 \; \mathrm{T}) = 15.4 \pm 0.7$ K due to vortex lattice formation. Fits to a broadening model find a magnetic penetration depth $λ(0 \; \mathrm{K})= 180.57 \pm 0.30$ nm and upper critical field $B_\mathrm{c2}(0 \; \mathrm{K})= 18 \pm 4$ T, consistent with literature estimates. Spin-lattice relaxation (SLR) measurements find a Korringa response at low temperatures, with dynamic (i.e., thermally activated) contributions dominating above $\sim100$ K. Below $T_\mathrm{c}$, we observe a small Hebel-Slichter coherence peak characterized by a superconducting energy gap $Δ(0 \; \mathrm{K}) = 2.60 \pm 0.12$ meV and modest Dynes-like broadening. Our measurements suggest a gap ratio $2Δ(0 \; \mathrm{K})/k_\mathrm{B}T_\mathrm{c}(0 \; \mathrm{T}) = 3.92 \pm 0.25$, consistent with strong-coupling behavior. Sources for the dynamic high-$T$ relaxation are suggested.
△ Less
Submitted 20 May, 2025;
originally announced May 2025.
-
Multipacting mitigation by atomic layer deposition: the case study of Titanium Nitride
Authors:
Yasmine Kalboussi,
Sarah Dadouch,
Baptiste Delatte,
Frédéric Miserques,
Diana Dragoe,
Fabien Eozenou,
Matthieu Baudrier,
Sandrine Tusseau-Nenez,
Yunlin Zheng,
Luc Maurice,
Enrico Cenni,
Quentin Bertrand,
Patrick Sahuquet,
Elise Fayette,
Grégoire Jullien,
Christophe Inguimbert,
Mohamed Belhaj,
Thomas Proslier
Abstract:
This study investigates the use of Atomic Layer deposition (ALD) to mitigate multipacting phenomena inside superconducting radio frequency (SRF) cavities used in particle accelerators. The unique ALD capability to control the film thickness down to the atomic level on arbitrary complex shape objects enable the fine tuning of TiN film resistivity and total electron emission yield (TEEY) from coupon…
▽ More
This study investigates the use of Atomic Layer deposition (ALD) to mitigate multipacting phenomena inside superconducting radio frequency (SRF) cavities used in particle accelerators. The unique ALD capability to control the film thickness down to the atomic level on arbitrary complex shape objects enable the fine tuning of TiN film resistivity and total electron emission yield (TEEY) from coupons to devices. This level of control allows us to adequately choose a TiN film thickness that provide both a high resistivity to prevent Ohmic losses and low TEEY to mitigate multipacting for the application of interest. The methodology presented in this work can be scaled to other domain and devices subject to RF fields in vacuum and sensitive to multipacting or electron discharge processes with their own requirements in resistivities and TEEY values
△ Less
Submitted 29 May, 2024;
originally announced May 2024.
-
Superconducting phase transitions in disordered NbTiN films
Authors:
M. V. Burdastyh,
S. V. Postolova,
T. Proslier,
S. S. Ustavshikov,
A. V. Antonov,
V. M. Vinokur,
A. Yu. Mironov
Abstract:
The suppression of superconductivity in disordered systems is a fundamental problem of condensed matter physics. Here we investigate the superconducting niobium-titanium-nitride (Nb_{1-x}Ti_{x}N) thin films grown by atomic layer deposition (ALD) where disorder is controlled by the slight tuning of the ALD process parameters. We observe the smooth crossover from the disorder-driven superconductor-n…
▽ More
The suppression of superconductivity in disordered systems is a fundamental problem of condensed matter physics. Here we investigate the superconducting niobium-titanium-nitride (Nb_{1-x}Ti_{x}N) thin films grown by atomic layer deposition (ALD) where disorder is controlled by the slight tuning of the ALD process parameters. We observe the smooth crossover from the disorder-driven superconductor-normal metal transition (often reffered to as fermionic mechanism) to the case where bosonic mechanism dominates and increasing disorder leads to formation of metal with Cooper pairing. We show that, in moderately disordered films, the transition to zero-resistance state occurs in a full agreement with the conventional theories of superconducting fluctuations and Berezinskii-Kosterlitz-Thouless transition. However, the critically disordered films violate this accord showing low-temperature features possibly indicating the Bose metal phase. We show that it is the interrelation between film's sheet resistance in the maximum, R_{max}, of the resistive curve R(T) and R_q = h/4e^2 that distinguishes between these two behaviors. We reveal the characteristic features in magnetoresistance of the critically disordered films with R_{max} > R_q
△ Less
Submitted 1 December, 2019; v1 submitted 30 August, 2019;
originally announced September 2019.
-
Insight into bulk niobium superconducting RF cavities performances by tunneling spectroscopy
Authors:
N. R. Groll,
G. Ciovati,
A. Grassellino,
A. Romanenko,
J. F. Zasadzinski,
T. Proslier
Abstract:
Point contact tunneling (PCT) spectroscopy measurements are reported over wide areas of cm-sized cut outs from niobium superconducting RF cavities. A comparison is made between a high-quality, conventionally processed (CP) cavity with a high field Q drop for acceleration field E $>$ 20 MV/m and a nitrogen doped (N-doped) cavity that exhibits an increasing Q up to fields approaching 15 MV/m. The CP…
▽ More
Point contact tunneling (PCT) spectroscopy measurements are reported over wide areas of cm-sized cut outs from niobium superconducting RF cavities. A comparison is made between a high-quality, conventionally processed (CP) cavity with a high field Q drop for acceleration field E $>$ 20 MV/m and a nitrogen doped (N-doped) cavity that exhibits an increasing Q up to fields approaching 15 MV/m. The CP cavity displays hot spot regions at high RF fields where Q-drop occurs as well as unaffected regions (cold spots). PCT data on cold spots reveals a near ideal BCS density of states (DOS) with gap parameters, $Δ$ as high as 1.62 meV, that are among the highest values ever reported for Nb. Hot spot regions exhibit a wide distribution of gap values down to $Δ\sim$ 1.0 meV and DOS broadening characterized by a relatively large value of pair-breaking rate, $Γ$, indicating surface regions of significantly reduced superconductivity. In addition, hot spots commonly exhibit Kondo tunneling peaks indicative of surface magnetic moments attributed to a defective oxide. N-doped cavities reveal a more homoegeneous gap distribution centered at $Δ\sim$ 1.5 meV and relatively small values of $Γ/Δ$. The absence of regions of significantly reduced superconductivity indicates that the N interstitials are playing an important role in preventing the formation of hydride phases and other macroscopic defects which might otherwise severely affect the local, surface superconductivity that lead to hot spot formation. The N-doped cavities also display a significantly improved surface oxide, i.e., increased thickness and tunnel barrier height, compared to CP cavities. These results help explain the improved performance of N-doped cavities and give insights into the origin of the initial increasing Q with RF amplitude.
△ Less
Submitted 16 May, 2018;
originally announced May 2018.
-
Charge Berezinskii-Kosterlitz-Thouless transition in superconducting NbTiN films
Authors:
Alexey Yu. Mironov,
Daniel M. Silevitch,
Thomas Proslier,
SvetlanaV. Postolova,
Maria V. Burdastyh,
Anton K. Gutakovskii,
Thomas F. Rosenbaum,
Valerii M. Vinokur,
Tatyana I. Baturina
Abstract:
A half-century after the discovery of the superconductor-insulator transition (SIT), one of the fundamental predictions of the theory, the charge Berezinskii-Kosterlitz-Thouless (BKT) transition that is expected to occur at the insulating side of the SIT, has remained unobserved. The charge BKT transition is a phenomenon dual to the vortex BKT transition, which is at the heart of the very existenc…
▽ More
A half-century after the discovery of the superconductor-insulator transition (SIT), one of the fundamental predictions of the theory, the charge Berezinskii-Kosterlitz-Thouless (BKT) transition that is expected to occur at the insulating side of the SIT, has remained unobserved. The charge BKT transition is a phenomenon dual to the vortex BKT transition, which is at the heart of the very existence of two-dimensional superconductivity as a zero-resistance state appearing at finite temperatures. The dual picture points to the possibility of the existence of a superinsulating state endowed with zero conductance at finite temperature. Here, we report the observation of the charge BKT transition on the insulating side of the SIT, identified by the critical behavior of the resistance. We find that the critical temperature of the charge BKT transition depends on the magnetic field exhibiting first the fast growth and then passing through the maximum at fields much less than the upper critical field. Finally, we ascertain the effects of the finite electrostatic screening length and its divergence at the magnetic field-tuned approach to the superconductor-insulator transition.
△ Less
Submitted 30 July, 2017;
originally announced July 2017.
-
Atomic Layer deposition of 2D and 3D standards for quantitative synchrotron-based composition and structural analysis methods
Authors:
Nicholas G. Becker,
Anna Butterworth,
Andrey Sokolov,
Muriel Salome,
Steven Sutton,
De Andrade Vincent,
Andrew Westphal,
Thomas Proslier
Abstract:
The use of Standard Reference Materials (SRM) from the National Institute of Standards and Technology (NIST) for quantitative analysis of chemical composition using Synchrotron based X-Ray Florescence (SR-XRF) and Scanning Transmission X-Ray Microscopy (STXM) is common. These standards however can suffer from inhomogeneity in chemical composition and thickness and often require further calculation…
▽ More
The use of Standard Reference Materials (SRM) from the National Institute of Standards and Technology (NIST) for quantitative analysis of chemical composition using Synchrotron based X-Ray Florescence (SR-XRF) and Scanning Transmission X-Ray Microscopy (STXM) is common. These standards however can suffer from inhomogeneity in chemical composition and thickness and often require further calculations, based on sample mounting and detector geometry, to obtain quantitative results. These inhomogeneities negatively impact the reproducibility of the measurements and the quantitative measure itself. Atomic Layer Deposition (ALD) is an inexpensive, scalable deposition technique known for producing uniform, conformal films of a wide range of compounds on nearly any substrate material. These traits make it an ideal deposition method for producing films to replace the NIST standards and create SRM on a wide range of relevant 2D and 3D substrates. Utilizing Rutherford Backscattering, X-ray Reflectivity, Quartz crystal microbalance, STXM, and SR-XRF we show that ALD is capable of producing films that are homogenous over scales ranging from 100's of microns to nms
△ Less
Submitted 23 May, 2017;
originally announced May 2017.
-
A low energy muon spin rotation and point contact tunneling study of niobium films prepared for superconducting cavities
Authors:
T. Junginger,
S. Calatroni,
A. Sublet,
G. Terenziani,
T. Prokscha,
Z. Salman,
T. Proslier,
J. Zasadzinski
Abstract:
Point contact tunneling (PCT) and low energy muon spin rotation (LE-muSR) are used to probe, on the same samples, the surface superconducting properties of micrometer thick niobium films deposited onto copper substrates using different sputtereing techniques: diode, dc magnetron (dcMS) and HIPIMS. The combined results are compared to radio-frequency tests performances of RF cavities made with the…
▽ More
Point contact tunneling (PCT) and low energy muon spin rotation (LE-muSR) are used to probe, on the same samples, the surface superconducting properties of micrometer thick niobium films deposited onto copper substrates using different sputtereing techniques: diode, dc magnetron (dcMS) and HIPIMS. The combined results are compared to radio-frequency tests performances of RF cavities made with the same processes. Degraded surface superconducting properties are found to yield lower quality factors and stronger Q slope. In addition, both techniques find evidence for surface paramagnetism on all samples and particularly on Nb films prepared by HIPIMS.
△ Less
Submitted 23 November, 2017; v1 submitted 24 March, 2017;
originally announced March 2017.
-
Superconducting Energy Scales and Anomalous Dissipative Conductivity in Thin Films of Molybdenum Nitride
Authors:
Julian Simmendinger,
Uwe S. Pracht,
Lena Daschke,
Thomas Proslier,
Jeffrey A. Klug,
Martin Dressel,
Marc Scheffler
Abstract:
We report investigations of molybdenum nitride (MoN) thin films with different thickness and disorder and with superconducting transition temperature 9.89 K $\ge{T_c}\ge$ 2.78 K. Using terahertz frequency-domain spectroscopy we explore the normal and superconducting charge carrier dynamics for frequencies covering the range from 3 to 38 cm$^{-1}$ (0.1 to 1.1 THz). The superconducting energy scales…
▽ More
We report investigations of molybdenum nitride (MoN) thin films with different thickness and disorder and with superconducting transition temperature 9.89 K $\ge{T_c}\ge$ 2.78 K. Using terahertz frequency-domain spectroscopy we explore the normal and superconducting charge carrier dynamics for frequencies covering the range from 3 to 38 cm$^{-1}$ (0.1 to 1.1 THz). The superconducting energy scales, i.e. the critical temperature $T_c$, the pairing energy $Δ$, and the superfluid stiffness $J$, and the superfluid density $n_s$ can be well described within the Bardeen-Cooper-Schrieffer theory for conventional superconductors. At the same time, we find an anomalously large dissipative conductivity, which cannot be explained by thermally excited quasiparticles, but rather by a temperature-dependent normal-conducting fraction, persisting deep into the superconducting state. Our results on this disordered system constrain the regime, where discernible effects stemming from the disorder-induced superconductor-insulator transition possibly become relevant, to MoN films with a transition temperature lower than at least 2.78 K.
△ Less
Submitted 19 July, 2016;
originally announced July 2016.
-
Analysis of Nb3Sn surface layers for superconducting RF cavity applications
Authors:
Chaoyue Becker,
Samuel Posen,
Nickolas Groll,
Russell Cook,
Christian M. Schlepuetz,
Daniel Leslie Hall,
Matthias Liepe,
Michael Pellin,
John Zasadzsinski,
Thomas Proslier
Abstract:
We present an analysis of the Nb3Sn surface layers grown on a bulk niobium (Nb) coupon prepared at the same time and by the same vapor diffusion process used to make Nb3Sn coatings on 1.3 GHz cavities. Tunneling spectroscopy reveals a well-developed, homogeneous superconducting density of states at the surface with a gap value distribution centered around 2.7 meV and superconducting critical tempe…
▽ More
We present an analysis of the Nb3Sn surface layers grown on a bulk niobium (Nb) coupon prepared at the same time and by the same vapor diffusion process used to make Nb3Sn coatings on 1.3 GHz cavities. Tunneling spectroscopy reveals a well-developed, homogeneous superconducting density of states at the surface with a gap value distribution centered around 2.7 meV and superconducting critical temperature (Tc) up to 16.3 K. Scanning Electron microscopy (STEM) performed on cross section of the sample's surface region shows a 2 microns thick Nb3Sn surface layer. The elemental composition map exhibits a Nb over Sn ratio of 3 and reveals the presence of buried sub-stoichiometric regions that have a ratio f 5. Synchrotron x-ray diffraction experiments indicate a polycrystalline Nb3Sn film and confirm the presence of Nb rich regions that occupy about a third of the coating volume. These low Tc regions could play an important role in the dissipation mechanism occurring during RF tests of Nb3Sn-coated cavities and open the way for further improving a very promising alternative to pure Nb cavities for particle accelerators.
△ Less
Submitted 11 March, 2015;
originally announced March 2015.
-
Giant two-phonon Raman scattering from nanoscale NbC precipitates in Nb
Authors:
C. Cao,
R. Tao,
D. C. Ford,
R. F. Klie,
T. Proslier,
L. D. Cooley,
A. Dzyuba,
P. Zapol,
M. Warren,
H. Lind,
J. F. Zasadzinski
Abstract:
High purity niobium (Nb), subjected to the processing methods used in the fabrication of superconducting RF cavities, displays micron-sized surface patches containing excess carbon. High-resolution transmission electron microscopy and electron energy-loss spectroscopy measurements are presented which reveal the presence of nanoscale NbC coherent precipitates in such regions. Raman backscatter spec…
▽ More
High purity niobium (Nb), subjected to the processing methods used in the fabrication of superconducting RF cavities, displays micron-sized surface patches containing excess carbon. High-resolution transmission electron microscopy and electron energy-loss spectroscopy measurements are presented which reveal the presence of nanoscale NbC coherent precipitates in such regions. Raman backscatter spectroscopy on similar surface regions exhibit spectra consistent with the literature results on bulk NbC but with significantly enhanced two-phonon scattering. The unprecedented strength and sharpness of the two-phonon signal has prompted a theoretical analysis, using density functional theory (DFT), of phonon modes in NbC for two different interface models of the coherent precipitate. One model leads to overall compressive strain and a comparison to ab-initio calculations of phonon dispersion curves under uniform compression of the NbC shows that the measured two-phonon peaks are linked directly to phonon anomalies arising from strong electron-phonon interaction. Another model of the extended interface between Nb and NbC, studied by DFT, gives insight into the frequency shifts of the acoustic and optical mode density of states measured by first order Raman. The exact origin of the stronger two-phonon response is not known at present but it suggests the possibility of enhanced electron-phonon coupling in transition metal carbides under strain found either in the bulk NbC inclusions or at their interfaces with Nb metal. Preliminary tunneling studies using a point contact method show some energy gaps larger than expected for bulk NbC.
△ Less
Submitted 9 March, 2015;
originally announced March 2015.
-
Tunneling spectroscopy of superconducting MoN and NbTiN grown by atomic layer deposition
Authors:
Nickolas Groll,
Jeffrey A. Klug,
Chaoyue Cao,
Serdar Altin,
Helmut Claus,
Nicholas G. Becker,
John F. Zasadzinski,
Michael J. Pellin,
Thomas Proslier
Abstract:
A tunneling spectroscopy study is presented of superconducting MoN and Nb$_{0.8}$Ti$_{0.2}$N thin films grown by atomic layer deposition (ALD). The films exhibited a superconducting gap of 2meV and 2.4meV respectively with a corresponding critical temperature of 11.5K and 13.4K, among the highest reported $T_c$ values achieved by the ALD technique. Tunnel junctions were obtained using a mechanical…
▽ More
A tunneling spectroscopy study is presented of superconducting MoN and Nb$_{0.8}$Ti$_{0.2}$N thin films grown by atomic layer deposition (ALD). The films exhibited a superconducting gap of 2meV and 2.4meV respectively with a corresponding critical temperature of 11.5K and 13.4K, among the highest reported $T_c$ values achieved by the ALD technique. Tunnel junctions were obtained using a mechanical contact method with a Au tip. While the native oxides of these films provided poor tunnel barriers, high quality tunnel junctions with low zero bias conductance (below $\sim$10%) were obtained using an artificial tunnel barrier of Al$_2$O$_3$ on the film's surface grown $\textit{ex situ}$ by ALD. We find a large critical current density on the order of $4\times 10^6$A/cm$^2$ at $T=0.8T_c$ for a 60nm MoN film and demonstrate conformal coating capabilities of ALD onto high aspect ratio geometries. These results suggest the ALD technique offers significant promise for thin film superconducting device applications.
△ Less
Submitted 20 December, 2013;
originally announced December 2013.
-
Heteroepitaxy of Group IV-VI Nitrides by Atomic Layer Deposition
Authors:
Jeffrey A. Klug,
Nicholas G. Becker,
Nickolas R. Groll,
Chaoyue Cao,
Matthew S. Weimer,
Michael J. Pellin,
John F. Zasadzinski,
Thomas Proslier
Abstract:
Heteroepitaxial growth of selected group IV-VI nitrides on various orientations of sapphire (α-Al2O3) is demonstrated using atomic layer deposition. High quality, epitaxial films are produced at significantly lower temperatures than required by conventional deposition methods. Characterization of electrical and superconducting properties of epitaxial films reveals a reduced room temperature resist…
▽ More
Heteroepitaxial growth of selected group IV-VI nitrides on various orientations of sapphire (α-Al2O3) is demonstrated using atomic layer deposition. High quality, epitaxial films are produced at significantly lower temperatures than required by conventional deposition methods. Characterization of electrical and superconducting properties of epitaxial films reveals a reduced room temperature resistivity and increased residual resistance ratio (RRR) for films deposited on sapphire compared to polycrystalline samples deposited concurrently on fused quartz substrates.
△ Less
Submitted 6 September, 2013;
originally announced September 2013.
-
Effect of high temperature heat treatments on the quality factor of a large-grain superconducting radio-frequency niobium cavity
Authors:
P. Dhakal,
G. Ciovati,
G. R. Myneni,
K. E. Gray,
N. Groll,
P. Maheshwari,
D. M. McRae,
R. Pike,
T. Proslier,
F. Stevie,
R. P. Walsh,
Q. Yang,
J. Zasadzinzki
Abstract:
Large-grain Nb has become a viable alternative to fine-grain Nb for the fabrication of superconducting radio-frequency cavities. In this contribution we report the results from a heat treatment study of a large-grain 1.5 GHz single-cell cavity made of "medium purity" Nb. The baseline surface preparation prior to heat treatment consisted of standard buffered chemical polishing. The heat treatment i…
▽ More
Large-grain Nb has become a viable alternative to fine-grain Nb for the fabrication of superconducting radio-frequency cavities. In this contribution we report the results from a heat treatment study of a large-grain 1.5 GHz single-cell cavity made of "medium purity" Nb. The baseline surface preparation prior to heat treatment consisted of standard buffered chemical polishing. The heat treatment in the range 800 - 1400 C was done in a newly designed vacuum induction furnace. Q0 values of the order of 2x1010 at 2.0 K and peak surface magnetic field (Bp) of 90 mT were achieved reproducibly. A Q0-value of (5+-1)1010 at 2.0 K and Bp = 90 mT was obtained after heat treatment at 1400 C. This is the highest value ever reported at this temperature, frequency and field. Samples heat treated with the cavity at 1400 C were analyzed by secondary ion mass spectrometry, secondary electron microscopy, energy dispersive X-ray, point contact tunneling and X-ray diffraction and revealed a complex surface composition which includes titanium oxide, increased carbon and nitrogen content but reduced hydrogen concentration compared to a non heat-treated sample.
△ Less
Submitted 25 March, 2013; v1 submitted 25 October, 2012;
originally announced October 2012.
-
Surface impedance of superconductors with magnetic impurities
Authors:
Maxim Kharitonov,
Thomas Proslier,
Andreas Glatz,
Michael J. Pellin
Abstract:
Motivated by the problem of the residual surface resistance of the superconducting radio-frequency (SRF) cavities, we develop a microscopic theory of the surface impedance of s-wave superconductors with magnetic impurities. We analytically calculate the current response function and surface impedance for a sample with spatially uniform distribution of impurities, treating magnetic impurities in th…
▽ More
Motivated by the problem of the residual surface resistance of the superconducting radio-frequency (SRF) cavities, we develop a microscopic theory of the surface impedance of s-wave superconductors with magnetic impurities. We analytically calculate the current response function and surface impedance for a sample with spatially uniform distribution of impurities, treating magnetic impurities in the framework of the Shiba theory. The obtained general expressions hold in a wide range of parameter values, such as temperature, frequency, mean free path, and exchange coupling strength. This generality, on the one hand, allows for direct numerical implementation of our results to describe experimental systems (SRF cavities, superconducting qubits) under various practically relevant conditions. On the other hand, explicit analytical expressions can be obtained in a number of limiting cases, which makes possible further theoretical investigation of certain regimes. As a feature of key relevance to SRF cavities, we show that in the regime of "gapless superconductivity" the surface resistance exhibits saturation at zero temperature. Our theory thus explicitly demonstrates that magnetic impurities, presumably contained in the oxide surface layer of the SRF cavities, provide a microscopic mechanism for the residual resistance.
△ Less
Submitted 13 July, 2012; v1 submitted 15 September, 2011;
originally announced September 2011.
-
Atomic layer deposition and superconducting properties of NbSi films
Authors:
Thomas Proslier,
Jeffrey A. Klug,
Jeffrey W. Elam,
Helmut Claus,
Nicholas G. Becker,
Michael Pellin
Abstract:
Atomic layer deposition was used to synthesize niobium silicide (NbSi) films with a 1:1 stoichiometry, using NbF5 and Si2H6 as precursors. The growth mechanism at 200oC was examined by in-situ quartz crystal microbalance (QCM) and quadrupole mass spectrometer (QMS). This study revealed a self-limiting reaction with a growth rate of 4.5 Å/cycle. NbSi was found to grow only on oxide-free films prepa…
▽ More
Atomic layer deposition was used to synthesize niobium silicide (NbSi) films with a 1:1 stoichiometry, using NbF5 and Si2H6 as precursors. The growth mechanism at 200oC was examined by in-situ quartz crystal microbalance (QCM) and quadrupole mass spectrometer (QMS). This study revealed a self-limiting reaction with a growth rate of 4.5 Å/cycle. NbSi was found to grow only on oxide-free films prepared using halogenated precursors. The electronic properties, growth rate, chemical composition, and structure of the films were studied over the deposition temperature range 150-400oC. For all temperatures, the films are found to be stoichiometric NbSi (1:1) with no detectable fluorine impurities, amorphous with a density of 6.65g/cm3, and metallic with a resistivity ρ=150 μΩ.cm at 300K for films thicker than 35 nm. The growth rate was nearly constant for deposition temperatures between 150-275oC, but increases above 300oC suggesting the onset of non-self limiting growth. The electronic properties of the films were measured down to 1.2K and revealed a superconducting transition at Tc=3.1K. To our knowledge, a superconducting niobium silicide film with a 1:1 stoichiometry has never been grown before by any technique.
△ Less
Submitted 18 April, 2011;
originally announced April 2011.
-
Rebuttal to "Comment by V.M. Krasnov on 'Counterintuitive consequence of heating in strongly-driven intrinsic junctions of Bi2Sr2CaCu2O8+d Mesas' "
Authors:
C. Kurter,
L. Ozyuzer,
T. Proslier,
J. F. Zasadzinski,
D. G. Hinks,
K. E. Gray
Abstract:
In our article [1], we found that with increasing dissipation there is a clear, systematic shift and sharpening of the conductance peak along with the disappearance of the higher-bias dip/hump features (DHF), for a stack of intrinsic Josephson junctions (IJJs) of intercalated Bi2Sr2CaCu2O8+δ (Bi2212). Our work agrees with Zhu et al [2] on unintercalated, pristine Bi2212, as both studies show the s…
▽ More
In our article [1], we found that with increasing dissipation there is a clear, systematic shift and sharpening of the conductance peak along with the disappearance of the higher-bias dip/hump features (DHF), for a stack of intrinsic Josephson junctions (IJJs) of intercalated Bi2Sr2CaCu2O8+δ (Bi2212). Our work agrees with Zhu et al [2] on unintercalated, pristine Bi2212, as both studies show the same systematic changes with dissipation. The broader peaks found with reduced dissipation [1,2] are consistent with broad peaks in the density-of-states (DOS) found among scanning tunneling spectroscopy [3] (STS), mechanical contact tunneling [4] (MCT) and inferred from angle (momentum) resolved photoemission spectroscopy [5] (ARPES); results that could not be ignored. Thus, sharp peaks are extrinsic and cannot correspond to the superconducting DOS. We suggested that the commonality of the sharp peaks in our conductance data, which is demonstrably shown to be heating-dominated, and the peaks of previous intrinsic tunneling spectroscopy (ITS) data implies that these ITS reports might need reinterpretation.
△ Less
Submitted 15 September, 2010;
originally announced September 2010.
-
Modeling rf breakdown arcs II: plasma / materials interactions
Authors:
Zeke Insepov,
Jim Norem,
Thomas Proslier,
Sudhakar Mahalingam,
S. Veitzer
Abstract:
Continuing the description of rf vacuum arcs from an earlier paper, we describe some aspects of the interaction of vacuum arcs that involve the surface. This paper describes aspects of plasma materials interactions that affect the arc and models measurement of the surface field using the Tonks-Frenkel and the spinodal electrohydrodynamic instabilities, a realistic model for the generation and eval…
▽ More
Continuing the description of rf vacuum arcs from an earlier paper, we describe some aspects of the interaction of vacuum arcs that involve the surface. This paper describes aspects of plasma materials interactions that affect the arc and models measurement of the surface field using the Tonks-Frenkel and the spinodal electrohydrodynamic instabilities, a realistic model for the generation and evaluation of high field enhancements, unipolar arcs, creep and other effects.
△ Less
Submitted 3 April, 2012; v1 submitted 11 June, 2010;
originally announced June 2010.
-
Counterintuitive Consequence of Heating in Strongly-Driven Intrinsic-Junctions of Bi$_{2}$Sr$_{2}$CaCu$_{2}$O$_{8+δ}$ Mesas
Authors:
C. Kurter,
L. Ozyuzer,
T. Proslier,
J. F. Zasadzinski,
D. G. Hinks,
K. E. Gray
Abstract:
Anomalously high and sharp peaks in the conductance of intrinsic Josephson junctions in Bi$_{2}$Sr$_{2}$CaCu$_{2}$O$_{8+δ}$ (Bi2212) mesas have been universally interpreted as superconducting energy gaps, but here we show they are a result of heating. This interpretation follows from a direct comparison to the equilibrium gap, $\mathit Δ$, measured in break junctions on similar Bi2212 crystals.…
▽ More
Anomalously high and sharp peaks in the conductance of intrinsic Josephson junctions in Bi$_{2}$Sr$_{2}$CaCu$_{2}$O$_{8+δ}$ (Bi2212) mesas have been universally interpreted as superconducting energy gaps, but here we show they are a result of heating. This interpretation follows from a direct comparison to the equilibrium gap, $\mathit Δ$, measured in break junctions on similar Bi2212 crystals. As the dissipated power increases with a greater number of junctions in the mesa, the conductance peak abruptly sharpens and its voltage decreases to well below 2$\mathit Δ$. This sharpening, found in our experimental data, defies conventional intuition of heating effects on tunneling spectra, but it can be understood as an instability into a nonequilibrium two-phase coexistent state. The measured peak positions occur accurately within the voltage range that an S-shaped backbending is found in the {\it calculated} current-voltage curves for spatially {\it uniform} self-heating and that S-shape implies the potential for the uniform state to be unstable.
△ Less
Submitted 9 November, 2009;
originally announced November 2009.
-
Improvement and protection of niobium surface superconductivity by Atomic Layer Deposition and heat treatment
Authors:
T. Proslier,
J. Zasadzinski,
J. Moore,
M. Pellin,
J. Elam,
L. Cooley,
C. Antoine,
J. Norem,
K. E. Gray
Abstract:
A method to treat the surface of Nb is described which potentially can improve the performance of superconducting RF cavities. We present tunneling and x-ray photoemission spectroscopy (XPS) measurements at the surface of cavity-grade niobium samples coated with a 3 nm alumina overlayer deposited by Atomic Layer Deposition (ALD). The coated samples baked in ultra high vacuum (UHV) at low tempera…
▽ More
A method to treat the surface of Nb is described which potentially can improve the performance of superconducting RF cavities. We present tunneling and x-ray photoemission spectroscopy (XPS) measurements at the surface of cavity-grade niobium samples coated with a 3 nm alumina overlayer deposited by Atomic Layer Deposition (ALD). The coated samples baked in ultra high vacuum (UHV) at low temperature reveal at first degraded superconducting surface. However, at temperatures above 450C, the tunneling conductance curves show significant improvements of the superconducting density of states (DOS) compared with untreated surfaces.
△ Less
Submitted 25 August, 2008;
originally announced August 2008.
-
Tunneling study of cavity grade Nb: possible magnetic scattering at the surface
Authors:
T. Proslier,
J. F. Zasadzinski,
L. Cooley,
C. Antoine,
J. Moore,
M. Pellin,
J. Norem,
K. E. Gray
Abstract:
Tunneling spectroscopy was performed on Nb pieces prepared by the same processes used to etch and clean superconducting radio frequency (SRF) cavities. Air exposed, electropolished Nb exhibited a surface superconducting gap delta=1.55 meV, characteristic of clean, bulk Nb. However the tunneling density of states (DOS) was broadened significantly. The Nb pieces treated with the same mild baking u…
▽ More
Tunneling spectroscopy was performed on Nb pieces prepared by the same processes used to etch and clean superconducting radio frequency (SRF) cavities. Air exposed, electropolished Nb exhibited a surface superconducting gap delta=1.55 meV, characteristic of clean, bulk Nb. However the tunneling density of states (DOS) was broadened significantly. The Nb pieces treated with the same mild baking used to improve the Q-slope in SRF cavities, reveal a sharper DOS. Good fits to the DOS were obtained using Shiba theory, suggesting that magnetic scattering of quasiparticles is the origin of the gapless surface superconductivity and a heretofore unrecognized contributor to the Q-slope problem of Nb SRF cavities.
△ Less
Submitted 19 March, 2008;
originally announced March 2008.
-
Probing the superconducting condensate on a nanometer scale
Authors:
Th. Proslier,
A. Kohen,
Y. Noat,
T. Cren,
D. Roditchev,
W. Sacks
Abstract:
Superconductivity is a rare example of a quantum system in which the wavefunction has a macroscopic quantum effect, due to the unique condensate of electron pairs. The amplitude of the wavefunction is directly related to the pair density, but both amplitude and phase enter the Josephson current : the coherent tunneling of pairs between superconductors. Very sensitive devices exploit the supercon…
▽ More
Superconductivity is a rare example of a quantum system in which the wavefunction has a macroscopic quantum effect, due to the unique condensate of electron pairs. The amplitude of the wavefunction is directly related to the pair density, but both amplitude and phase enter the Josephson current : the coherent tunneling of pairs between superconductors. Very sensitive devices exploit the superconducting state, however properties of the {\it condensate} on the {\it local scale} are largely unknown, for instance, in unconventional high-T$_c$ cuprate, multiple gap, and gapless superconductors.
The technique of choice would be Josephson STS, based on Scanning Tunneling Spectroscopy (STS), where the condensate is {\it directly} probed by measuring the local Josephson current (JC) between a superconducting tip and sample. However, Josephson STS is an experimental challenge since it requires stable superconducting tips, and tunneling conditions close to atomic contact. We demonstrate how these difficulties can be overcome and present the first spatial mapping of the JC on the nanometer scale. The case of an MgB$_2$ film, subject to a normal magnetic field, is considered.
△ Less
Submitted 1 February, 2006;
originally announced February 2006.
-
Probing the superfluid velocity with a superconducting tip: the Doppler shift effect
Authors:
A. Kohen,
Th. Proslier,
T. Cren,
Y. Noat,
W. Sacks,
H. Berger,
D. Roditchev
Abstract:
We address the question of probing the supercurrents in superconducting (SC) samples on a local scale by performing Scanning Tunneling Spectroscopy (STS) experiments with a SC tip. In this configuration, we show that the tunneling conductance is highly sensitive to the Doppler shift term in the SC quasiparticle spectrum of the sample, thus allowing the local study of the superfluid velocity. Int…
▽ More
We address the question of probing the supercurrents in superconducting (SC) samples on a local scale by performing Scanning Tunneling Spectroscopy (STS) experiments with a SC tip. In this configuration, we show that the tunneling conductance is highly sensitive to the Doppler shift term in the SC quasiparticle spectrum of the sample, thus allowing the local study of the superfluid velocity. Intrinsic screening currents, such as those surrounding the vortex cores in a type II SC in a magnetic field, are directly probed. With Nb tips, the STS mapping of the vortices, in single crystal 2H-NbSe_2, reveals both the vortex cores, on the scale of the SC coherence length $ξ$, and the supercurrents, on the scale of the London penetration length $λ$. A subtle interplay between the SC pair potential and the supercurrents at the vortex edge is observed. Our results open interesting prospects for the study of screening currents in any superconductor.
△ Less
Submitted 30 November, 2005; v1 submitted 29 November, 2005;
originally announced November 2005.
-
Superconducting vortex profile from fixed point measurements The Lazy Fisherman tunnelling microscopy method
Authors:
A. Kohen,
T. Cren,
Th. Proslier,
Y. Noat,
F. Giubileo,
F. Bobba,
A. M. Cucolo,
W. Sacks D. Roditchev N. Zhigadlo,
S. M. Kazakov,
J. Karpinski
Abstract:
We introduce a mode of operation for studying the vortex phase in superconductors using scanning tunnelling microscopy (STM). While in the conventional STM method, the tip is scanned over a sample in which a fixed vortex pattern is prepared, in our "Lazy Fisherman" method the STM tip is kept fixed at a selected location while the vortices are being moved by varying the applied magnetic field. By…
▽ More
We introduce a mode of operation for studying the vortex phase in superconductors using scanning tunnelling microscopy (STM). While in the conventional STM method, the tip is scanned over a sample in which a fixed vortex pattern is prepared, in our "Lazy Fisherman" method the STM tip is kept fixed at a selected location while the vortices are being moved by varying the applied magnetic field. By continuously acquiring the local tunnelling conductance spectra, dI/dV(V), we detect the changes in the local density of states under the tip due to the vortex motion. With no need for scanning, the method permits one to extend the study of vortices to samples in which scanning is difficult or even impossible due to surface nonuniformity and allows one to study vortex dynamics. Using a statistical analysis of the spectra, we reconstruct the single vortex zero bias conductance profile. We apply the method to the c-axis face of an MgB$_2$ single crystal sample and obtain a vortex profile with a coherence length, xi of 57+-2 nm.
△ Less
Submitted 3 May, 2005;
originally announced May 2005.
-
Fabrication and characterization of scanning tunneling microscopy superconducting Nb tips having highly enhanced critical fields
Authors:
A. Kohen,
Y. Noat,
T. Proslier,
E. Lacaze,
M. Aprili,
W. Sacks,
D. Roditchev
Abstract:
We report a simple method for the fabrication of Niobium superconducting (SC) tips for scanning tunnelling microscopy which allow atomic resolution. The tips, formed in-situ by the mechanical breaking of a niobium wire, reveal a clear SC gap of 1.5 meV and a critical temperature Tc=9.2+-0.3 K as deduced from Superconductor Insulator Normal metal (NIS) and Superconductor Insulator Superconductor…
▽ More
We report a simple method for the fabrication of Niobium superconducting (SC) tips for scanning tunnelling microscopy which allow atomic resolution. The tips, formed in-situ by the mechanical breaking of a niobium wire, reveal a clear SC gap of 1.5 meV and a critical temperature Tc=9.2+-0.3 K as deduced from Superconductor Insulator Normal metal (NIS) and Superconductor Insulator Superconductor (SIS) spectra. These match the values of bulk Nb samples. We systematically find an enhanced value of the critical magnetic field in which superconductivity in the tip is destroyed (around 1 T for some tips) up to five times larger than the critical field of bulk Nb (0.21 T). Such enhancement is attributed to a size effect at the tip apex
△ Less
Submitted 4 December, 2004;
originally announced December 2004.
-
Two regimes in the magnetic field response of superconducting MgB$_2$
Authors:
A. Kohen,
F. Giubileo,
Th. Proslier,
F. Bobba,
Y. Noat,
A. Troianovski,
A. M. Cucolo,
W. Sacks,
J. Klein,
D. Roditchev,
N. Zhigadlo,
S. M. Kazakov,
J. Karpinski
Abstract:
Using Scanning Tunneling Microscope at low temperature we explore the superconducting phase diagram in the $π$-band of the two-band superconductor MgB$_2$. In this band the peculiar shape of the local tunneling spectra and their dynamics in the magnetic field reveal the complex character of the quasiparticle density of states (DOS). The gap in the DOS is first rapidly filled with states in raisi…
▽ More
Using Scanning Tunneling Microscope at low temperature we explore the superconducting phase diagram in the $π$-band of the two-band superconductor MgB$_2$. In this band the peculiar shape of the local tunneling spectra and their dynamics in the magnetic field reveal the complex character of the quasiparticle density of states (DOS). The gap in the DOS is first rapidly filled with states in raising the magnetic field up to 0.5 T and then slowly approaches the normal state value : The gap is observed up to 2 T. Such a change in the DOS dynamics suggests the existence of two terms in the DOS of the $π$-band: a first one, reflecting an intrinsic superconductivity in the band and a second one, originating from an inter-band coupling to the $σ$-band. Our findings allow a deeper understanding of the unique phase diagram of MgB$_2$.
△ Less
Submitted 29 March, 2004;
originally announced March 2004.
