Showing 1–50 of 118 results for author: Persson, B

Sliding Friction of Hard Sliders on Rubber: Theory and Experiment

Authors: R. Xu, B. N. J. Persson

Abstract: We present a study of sliding friction for rigid triangular steel sliders on soft rubber substrates under both lubricated and dry conditions. For rubber surfaces lubricated with a thin film of silicone oil, the measured sliding friction at room temperature agrees well with theoretical predictions obtained from a viscoelastic model originally developed for rolling friction. On the lubricated surfac… ▽ More We present a study of sliding friction for rigid triangular steel sliders on soft rubber substrates under both lubricated and dry conditions. For rubber surfaces lubricated with a thin film of silicone oil, the measured sliding friction at room temperature agrees well with theoretical predictions obtained from a viscoelastic model originally developed for rolling friction. On the lubricated surface, the sliding friction is primarily due to bulk viscoelastic energy dissipation in the rubber. The model, which includes strain-dependent softening of the rubber modulus, accurately predicts the experimental friction curves. At lower temperatures ($T = -20^\circ {\rm C}$ and $-40^\circ {\rm C}$), the measured friction exceeds the theoretical prediction. We attribute this increase to penetration of the lubricant film by surface asperities, leading to a larger adhesive contribution. For dry surfaces, the adhesive contribution becomes dominant. By subtracting the viscoelastic component inferred from the lubricated case, we estimate the interfacial frictional shear stress. This shear stress increases approximately linearly with the logarithm of the sliding speed, consistent with stress-augmented thermal activation mechanisms. △ Less

Submitted 25 May, 2025; v1 submitted 22 May, 2025; originally announced May 2025.

Rubber Wear: History, Mechanisms, and Perspectives

Authors: R. Xu, W. Sheng, F. Zhou, B. N. J. Persson

Abstract: This paper presents a comprehensive review of wear mechanisms, with a primary focus on rubber wear under sliding conditions. Beginning with classical wear theories, including the Archard and Rabinowicz models, we analyze their applicability to both metals and elastomers and discuss extensions relevant to elastic contact and multiscale surface roughness. Various experimental studies on rubber, such… ▽ More This paper presents a comprehensive review of wear mechanisms, with a primary focus on rubber wear under sliding conditions. Beginning with classical wear theories, including the Archard and Rabinowicz models, we analyze their applicability to both metals and elastomers and discuss extensions relevant to elastic contact and multiscale surface roughness. Various experimental studies on rubber, such as abrasion by sharp tools, erosion by particle impact, and wear during sliding on rough substrates, are reviewed and interpreted. The effects of environmental factors, such as oxygen and lubrication, are also discussed. In addition, we review a recently proposed wear model based on fatigue crack growth within asperity contact regions, which accounts for energy dissipation and multiscale interactions. This model explains the wide variability in the wear coefficient and predicts wear rates consistent with experimental observations across a broad range of conditions. It also explains the formation mechanism and provides the size distribution of rubber wear particles, from micrometer-scale up to severe cut-chip-chunk (CCC) wear. The results have implications for tire wear and the environmental impact of microscale wear debris (microplastics). △ Less

Submitted 28 March, 2025; v1 submitted 25 March, 2025; originally announced March 2025.

Rubber wear on concrete: dry and in-water conditions

Authors: R. Xu, N. Miyashita, B. N. J. Persson

Abstract: Rubber wear results from the removal of small (micrometer-sized) rubber particles through crack propagation. In this study, we investigate the wear behavior of Styrene-Butadiene Rubber (SBR) and Natural Rubber (NR) sliding on two different concrete surfaces under dry and wet (in water) conditions. Experiments are conducted at low sliding speeds ($\approx 3 \ {\rm mm/s}$) to minimize frictional hea… ▽ More Rubber wear results from the removal of small (micrometer-sized) rubber particles through crack propagation. In this study, we investigate the wear behavior of Styrene-Butadiene Rubber (SBR) and Natural Rubber (NR) sliding on two different concrete surfaces under dry and wet (in water) conditions. Experiments are conducted at low sliding speeds ($\approx 3 \ {\rm mm/s}$) to minimize frictional heating and hydrodynamic effects. For two SBR compounds, we observe significantly higher wear rates in water compared to the dry state, with enhancement factors of $1.5-2.5$ for a low-glass-transition-temperature SBR compound ($T_{\rm g} = -50^\circ {\rm C}$) and approximately $4$ for a higher-glass-transition compound ($T_{\rm g} = -7^\circ {\rm C}$). In contrast, the NR compound showed no wear in water at low nominal contact pressures ($σ_0 \approx 0.12$, $0.16$, and $0.25 \ {\rm MPa}$), while at higher pressures ($σ_0 \approx 0.36$ and $0.49 \ {\rm MPa}$), the wear rates in dry and in-water states are similar. The findings provide insights into the mechanisms of rubber wear under varying environmental and mechanical conditions, highlighting the influence of material properties, interfacial effects, and applied pressures on wear behavior. △ Less

Submitted 16 April, 2025; v1 submitted 21 January, 2025; originally announced January 2025.

Sliding wear: role of plasticity

Authors: Ruibin Xu, B. N. J. Persson

Abstract: We present experimental wear data for polymethyl methacrylate (PMMA) sliding on tile, sandpaper, and polished steel surfaces, as well as for soda-lime, borosilicate, and quartz glass sliding on sandpaper. The results are compared with a recently developed theory \cite{ToBe} of sliding wear based on crack propagation (fatigue), originally formulated for elastic contact and here extended to include… ▽ More We present experimental wear data for polymethyl methacrylate (PMMA) sliding on tile, sandpaper, and polished steel surfaces, as well as for soda-lime, borosilicate, and quartz glass sliding on sandpaper. The results are compared with a recently developed theory \cite{ToBe} of sliding wear based on crack propagation (fatigue), originally formulated for elastic contact and here extended to include plasticity. The elastoplastic wear model predicts wear rates that agree reasonably well with the experimental results for PMMA and soda-lime glass. However, deviations observed for quartz suggest that material-specific deformation mechanisms, particularly the differences between crystalline and amorphous structures, may need to be considered for accurate wear predictions across different materials. In addition, the model reveals a non-monotonic dependence of the wear rate on the penetration hardness $σ_{\rm P}$. Thus, for plastically soft material, the wear rate increases with increasing $σ_{\rm P}$, while for hard materials, it decreases. This contrasts with Archard's wear law, where the wear rate decreases monotonically with increasing $σ_{\rm P}$. △ Less

Submitted 21 June, 2025; v1 submitted 17 December, 2024; originally announced December 2024.

Rubber wear: experiment and theory

Authors: B. N. J. Persson, R. Xu, N. Miyashita

Abstract: We study the wear rate (mass loss per unit sliding distance) of a tire tread rubber compound sliding on concrete paver surfaces under dry and wet conditions, at different nominal contact pressures of $σ_0 = 0.12$, $0.29$, and $0.43 \ {\rm MPa}$, and sliding velocities ranging from $v= 1 \ {\rm μm/s}$ to $1 \ {\rm cm/s}$. We find that the wear rate is proportional to the normal force and remains in… ▽ More We study the wear rate (mass loss per unit sliding distance) of a tire tread rubber compound sliding on concrete paver surfaces under dry and wet conditions, at different nominal contact pressures of $σ_0 = 0.12$, $0.29$, and $0.43 \ {\rm MPa}$, and sliding velocities ranging from $v= 1 \ {\rm μm/s}$ to $1 \ {\rm cm/s}$. We find that the wear rate is proportional to the normal force and remains independent of the sliding speed. Sliding in water and soapy water results in significantly lower wear rates compared to dry conditions. The experimental data are analyzed using a theory that predicts wear rates and wear particle size distributions consistent with the experimental observations. △ Less

Submitted 11 November, 2024; originally announced November 2024.

Influence of temperature and crack-tip speed on crack propagation in elastic solids

Authors: B. N. J. Persson

Abstract: I study the influence of temperature and the crack-tip velocity of the bond breaking at the crack tip in rubber-like materials. The bond breaking is considered as a stress-aided thermally activated process and result in an effective crack propagation energy which increases strongly with decreasing temperature or increasing crack-tip speed. This effect is particular important for adhesive (interfac… ▽ More I study the influence of temperature and the crack-tip velocity of the bond breaking at the crack tip in rubber-like materials. The bond breaking is considered as a stress-aided thermally activated process and result in an effective crack propagation energy which increases strongly with decreasing temperature or increasing crack-tip speed. This effect is particular important for adhesive (interfacial) crack propagation but less important for cohesive crack propagation owing to the much larger bond-breaking energies in the latter case. For adhesive cracks the theory results are consistent with adhesion measurements for silicone (PDMS) rubber in contact with silica glass surfaces. For cohesive cracks the theory agree well with experimental results PDMS films chemically bound to silinized glass. △ Less

Submitted 9 September, 2024; originally announced September 2024.

On how to determine surface roughness power spectra

Authors: N. Rodriguez, L. Gontard, C. Ma, R. Xu, B. N. J. Persson

Abstract: Analytical contact mechanics theories depend on surface roughness through the surface roughness power spectrum. In the present study, we evaluated the usability of various experimental methods for studying surface roughness. Our findings indicated that height data obtained from optical methods often lack accuracy and should not be utilized for calculating surface roughness power spectra. Conversel… ▽ More Analytical contact mechanics theories depend on surface roughness through the surface roughness power spectrum. In the present study, we evaluated the usability of various experimental methods for studying surface roughness. Our findings indicated that height data obtained from optical methods often lack accuracy and should not be utilized for calculating surface roughness power spectra. Conversely, engineering stylus instruments and atomic force microscopy (AFM) typically yield reliable results that are consistent across the overlapping roughness length scale region. For surfaces with isotropic roughness, the two-dimensional (2D) power spectrum can be derived from the one-dimensional (1D) power spectrum using several approaches, which we explored in this paper. △ Less

Submitted 10 August, 2024; originally announced August 2024.

Brownian friction dynamics: fluctuations in sliding distance

Authors: Ruibin Xu, Feng Zhou, B. N. J. Persson

Abstract: We have studied the fluctuation (noise) in the position of sliding blocks under constant driving forces on different substrate surfaces. The experimental data are complemented by simulations using a simple spring-block model where the asperity contact regions are modeled by miniblocks connected to the big block by viscoelastic springs. The miniblocks experience forces that fluctuate randomly with… ▽ More We have studied the fluctuation (noise) in the position of sliding blocks under constant driving forces on different substrate surfaces. The experimental data are complemented by simulations using a simple spring-block model where the asperity contact regions are modeled by miniblocks connected to the big block by viscoelastic springs. The miniblocks experience forces that fluctuate randomly with the lateral position, simulating the interaction between asperities on the block and the substrate. The theoretical model provides displacement power spectra that agree well with the experimental results. △ Less

Submitted 23 June, 2024; originally announced June 2024.

Impact of Nanometer-Thin Stiff Layer on Adhesion to Rough Surfaces

Authors: Shubhendu Kumar, Babu Gaire, Bo Persson, Ali Dhinojwala

Abstract: Adhesion requires molecular contact, and natural adhesives employ mechanical gradients to achieve complete (conformal) contact to maximize adhesion. Intuitively, one expects that the higher the modulus of the top layer, the lower will be the adhesion strength. However, the relationship between the thickness of the stiff top layer and adhesion is not known. In this work, we quantified the adhesion… ▽ More Adhesion requires molecular contact, and natural adhesives employ mechanical gradients to achieve complete (conformal) contact to maximize adhesion. Intuitively, one expects that the higher the modulus of the top layer, the lower will be the adhesion strength. However, the relationship between the thickness of the stiff top layer and adhesion is not known. In this work, we quantified the adhesion between a stiff glassy poly (methyl methacrylate) (PMMA) layer of varying thickness on top of a soft poly dimethyl siloxane (PDMS) elastomer with a sapphire lens. We found that only about 90 nm thick PMMA layer on a relatively thicker, softer, and elastic PDMS block is required to drop macroscopic adhesion to almost zero during the loading cycle. This drop in adhesion for bilayers can be explained using a conformal model developed by Persson and Tosatti, where the elastic energy to create conformal contact depends on both the thickness and the mechanical properties of the bilayer. A better understanding of the influence of mechanical gradients on adhesion will have an impact on adhesives, friction, and colloidal and granular physics. △ Less

Submitted 22 February, 2024; originally announced February 2024.

Some comments on the fracture of viscoelastic solids

Authors: B. N. J. Persson, G. Carbone, C. Creton, G. Heinrich, T. Tada

Abstract: Crack propagation in viscoelastic solids like rubber is of great practical importance. Shrimali and Lopez-Pamies have proposed a new interesting approach for the crack propagation in viscoelastic solids. We give comments on the validity of the theory and point out some effects not included in the theory. Crack propagation in viscoelastic solids like rubber is of great practical importance. Shrimali and Lopez-Pamies have proposed a new interesting approach for the crack propagation in viscoelastic solids. We give comments on the validity of the theory and point out some effects not included in the theory. △ Less

Submitted 7 January, 2024; originally announced January 2024.

Comments: 4 pages, 2 figures

Surface roughness induced stress concentration

Authors: B. N. J. Persson

Abstract: When a body is exposed to external forces large local stresses may occur at the surface because of surface roughness. Surface stress concentration is important for many applications and in particular for fatigue due to pulsating external forces. For randomly rough surfaces I calculate the probability distribution of surface stress in response to a uniform external tensile stress with the displacem… ▽ More When a body is exposed to external forces large local stresses may occur at the surface because of surface roughness. Surface stress concentration is important for many applications and in particular for fatigue due to pulsating external forces. For randomly rough surfaces I calculate the probability distribution of surface stress in response to a uniform external tensile stress with the displacement vector field parallel to the rough surface. I present numerical simulation results for the stress distribution $σ(x,y)$ and show that in a typical case, the maximum local tensile stress may be $\sim 10$ times bigger than the applied stress. I discuss the role of the stress concentration on plastic deformation and surface crack generation and propagation. △ Less

Submitted 4 April, 2023; originally announced April 2023.

Comments: 18 pages,15 figures

On the stability of spinning asteroids

Authors: B. N. J. Persson, J. Biele

Abstract: Most asteroids with a diameter larger than $\sim 300 \ {\rm m}$ are rubble piles i.e. consisting of more than one solid object. All asteroids are rotating but almost all asteroids larger than $\sim 300 \ {\rm m}$ rotate with a period longer than $2.3 \ {\rm hours}$, which is the critical period where the centrifugal force equals the gravitational force. This indicates that there are nearly no adhe… ▽ More Most asteroids with a diameter larger than $\sim 300 \ {\rm m}$ are rubble piles i.e. consisting of more than one solid object. All asteroids are rotating but almost all asteroids larger than $\sim 300 \ {\rm m}$ rotate with a period longer than $2.3 \ {\rm hours}$, which is the critical period where the centrifugal force equals the gravitational force. This indicates that there are nearly no adhesive interaction forces between the asteroid fragments. We show that this is due to the surface roughness of the asteroid particles which reduces the van der Waals interaction between the particles by a factor of $100$ for micrometer sized particles and even more for larger particles. We show that surface roughness results in an interaction force which is independent of the size of the particles, in contrast to the linear size dependency expected for particles with smooth surfaces. Thus, two stone fragments of size $100 \ {\rm nm}$ attract each other with the same non-gravitational force as two fragments of size $10 \ {\rm m}$. △ Less

Submitted 27 October, 2021; originally announced October 2021.

Comments: 24 pages, 30 figures

Air, helium and water leakage in rubber O-ring seals with application to syringes

Authors: C. Huon, A. Tiwari, C. Rotella, P. Mangiagalli, B. N. J. Persson

Abstract: We study the leakage of fluids (liquids or gases) in syringes with glass barrel, steel plunger and rubber O-ring stopper. The leakrate depends on the interfacial surface roughness and on the viscoelastic properties of the rubber. Random surface roughness is produced by sandblasting the rubber O-rings. We present a very simple theory for gas flow which takes into account both the diffusive and ball… ▽ More We study the leakage of fluids (liquids or gases) in syringes with glass barrel, steel plunger and rubber O-ring stopper. The leakrate depends on the interfacial surface roughness and on the viscoelastic properties of the rubber. Random surface roughness is produced by sandblasting the rubber O-rings. We present a very simple theory for gas flow which takes into account both the diffusive and ballistic flow. The theory shows that the interfacial fluid flow (leakage) channels are so narrow that the gas flow is mainly ballistic (the so called Knudsen limit). We compare the leakrate obtained using air and helium. For barrels filled with water we observe no leakage even if leakage occurs for gases. We interpret this as resulting from capillary (Laplace pressure or surface energy) effects. △ Less

Submitted 20 October, 2021; originally announced October 2021.

Comments: 18 pages, 28 figures

Air leakage in seals with application to syringes

Authors: N. Rodriguez, A. Tiwari, B. N. J. Persson

Abstract: We study the leakage of air in syringes with Teflon coated rubber stopper and glass barrel. The leakrate depends on the interfacial surface roughness, the viscoelastic properties of the rubber and on the elastoplastic properties of the Teflon coating. The measured leakage rates are compared to the predictions of a simple theory for gas flow, which takes into account both the diffusive and ballisti… ▽ More We study the leakage of air in syringes with Teflon coated rubber stopper and glass barrel. The leakrate depends on the interfacial surface roughness, the viscoelastic properties of the rubber and on the elastoplastic properties of the Teflon coating. The measured leakage rates are compared to the predictions of a simple theory for gas flow, which takes into account both the diffusive and ballistic air flow, and the elastoplastic multiscale contact mechanics which determines the probability distribution of interfacial separations. The theory shows that the interfacial air flow (leakage) channels are so narrow that the gas flow is mainly ballistic (the so called Knudsen limit). The implications for container closure integrity is discussed. △ Less

Submitted 4 August, 2021; originally announced August 2021.

Comments: 7 pages, 9 figures

Crack and pull-off dynamics of adhesive, viscoelastic solids

Authors: Martin H. Müser, Bo N. J. Persson

Abstract: When quickly detaching an elastomer from a counterface, viscoelasticity dramatically increases the perceived adhesion relative to its adiabatic or equilibrium value. Here, we report simulations on the sticking contact between a rigid cylinder and a viscoelastic half space revealing a maximum in the work of adhesion at intermediate pull-off velocities. Maximum tensile forces yet increase monotonica… ▽ More When quickly detaching an elastomer from a counterface, viscoelasticity dramatically increases the perceived adhesion relative to its adiabatic or equilibrium value. Here, we report simulations on the sticking contact between a rigid cylinder and a viscoelastic half space revealing a maximum in the work of adhesion at intermediate pull-off velocities. Maximum tensile forces yet increase monotonically with the pull-off speed and the crack-tip speed in accordance with the Persson-Brener approach. As predicted theoretically, the fracture mode transitions from interfacial crack propagation to quasi-uniform bond breaking with increasing range of adhesion. △ Less

Submitted 5 August, 2021; v1 submitted 4 August, 2021; originally announced August 2021.

On opening crack propagation in viscoelastic solids

Authors: B. N. J. Persson

Abstract: We show that the Persson-Brener theory of crack propagation in viscoelastic solids gives a viscoelastic fracture energy factor $G/G_0 = 1+f$ which is nearly the same as the viscoelastic factor obtained using the cohesive-zone model. We also discuss finite-size effects and comment on the use of crack propagation theories for "solids" with a viscoelastic modulus that vanishes at zero frequency. We show that the Persson-Brener theory of crack propagation in viscoelastic solids gives a viscoelastic fracture energy factor $G/G_0 = 1+f$ which is nearly the same as the viscoelastic factor obtained using the cohesive-zone model. We also discuss finite-size effects and comment on the use of crack propagation theories for "solids" with a viscoelastic modulus that vanishes at zero frequency. △ Less

Submitted 5 April, 2021; originally announced April 2021.

Comments: 5 pages, 5 figures

Side-leakage of facemask

Authors: B. N. J. Persson

Abstract: Face masks are used to trap particles (or fluid drops) in a porous material (filter) in order to avoid or reduce the transfer of particles between the human lungs (or mouth and nose) and the external environment. The air exchange between the lungs and the environment is assumed to occur through the facemask filter. However, if the resistance to air flow through the filter is high some air (and acc… ▽ More Face masks are used to trap particles (or fluid drops) in a porous material (filter) in order to avoid or reduce the transfer of particles between the human lungs (or mouth and nose) and the external environment. The air exchange between the lungs and the environment is assumed to occur through the facemask filter. However, if the resistance to air flow through the filter is high some air (and accompanied particles) will leak through the filter-skin interface. In this paper I will present a model study of the side-leakage problem. △ Less

Submitted 19 March, 2021; originally announced March 2021.

Comments: 9 pages, 15 figures

Rubber adhesion and friction: role of surface energy and contamination films

Authors: A. Tiwari, T. Tolpekina, Hans van Benthem, M. K. Gunnewiek, B. N. J. Persson

Abstract: We study the influence of the surface energy and contamination films on rubber adhesion and sliding friction. We find that there is a transfer of molecules from the rubber to the substrate which reduces the work of adhesion and makes the rubber friction insensitive to the substrate surface energy. We show that there is no simple relation between adhesion and friction: adhesion is due to (vertical)… ▽ More We study the influence of the surface energy and contamination films on rubber adhesion and sliding friction. We find that there is a transfer of molecules from the rubber to the substrate which reduces the work of adhesion and makes the rubber friction insensitive to the substrate surface energy. We show that there is no simple relation between adhesion and friction: adhesion is due to (vertical) detachment processes at the edge of the contact regions (opening crack propagation), while friction in many cases is determined mainly by (tangential) stick-slip instabilities of nanosized regions, within the whole sliding contact. Thus while the pull-off force in fluids may be strongly reduced (due to a reduction of the work of adhesion), the sliding friction may be only slightly affected as the area of real contact may be dry, and the frictional shear stress in the contact area nearly unaffected by the fluid. △ Less

Submitted 12 November, 2020; originally announced November 2020.

Comments: 13 pages, 21 figures

A simple model for viscoelastic crack propagation

Authors: B. N. J. Persson

Abstract: When a crack propagate in a viscoelastic solid energy dissipation can occur very far from the crack tip where the stress field may be very different from the $r^{-1/2}$ singular form expected close to the crack tip. Most theories of crack propagation focus on the near crack-tip region. Remarkable, here I show that a simple theory which does not account for the nature of the stress field in the nea… ▽ More When a crack propagate in a viscoelastic solid energy dissipation can occur very far from the crack tip where the stress field may be very different from the $r^{-1/2}$ singular form expected close to the crack tip. Most theories of crack propagation focus on the near crack-tip region. Remarkable, here I show that a simple theory which does not account for the nature of the stress field in the near crack-tip region result in a crack propagation energy in semi-quantitative agreement with a theory based on the stress field in the near crack-tip region. I consider both opening and closing crack propagation, and show that for closing crack propagation in viscoelastic solids, some energy dissipation processes must occur in thecrack tip process zone. △ Less

Submitted 13 September, 2020; originally announced September 2020.

Comments: 9 pages, 12 figures. arXiv admin note: text overlap with arXiv:2009.04936

Viscoelastic crack propagation: review of theories and applications

Authors: N. Rodriguez, P. Mangiagalli, B. N. J. Persson

Abstract: We review a theory of crack propagation in viscoelastic solids. We consider both cracks in infinite systems and in finite sized systems. As applications of the theory we consider two adhesion problems, namely pressure sensitive adhesives and the ball-flat adhesion problem. We also study crack propagation in the pig skin dermis, which is of medical relevance, and rubber wear in the context of tires… ▽ More We review a theory of crack propagation in viscoelastic solids. We consider both cracks in infinite systems and in finite sized systems. As applications of the theory we consider two adhesion problems, namely pressure sensitive adhesives and the ball-flat adhesion problem. We also study crack propagation in the pig skin dermis, which is of medical relevance, and rubber wear in the context of tires. △ Less

Submitted 10 September, 2020; originally announced September 2020.

Comments: 21 pages, 41 figures

Cylinder-flat contact mechanics with surface roughness

Authors: A. Tiwari, B. N. J. Persson

Abstract: We study the nominal (ensemble averaged) contact pressure $p(x)$ acting on a cylinder squeezed in contact with an elastic half-space with random surface roughness. The contact pressure is Hertzian-like for $α< 0.01$ and Gaussian-like for $α> 10$, where the dimensionless parameter $α= h_{\rm rms}/δ$ is the ratio between the root-mean-square roughness amplitude and the penetration for the smooth sur… ▽ More We study the nominal (ensemble averaged) contact pressure $p(x)$ acting on a cylinder squeezed in contact with an elastic half-space with random surface roughness. The contact pressure is Hertzian-like for $α< 0.01$ and Gaussian-like for $α> 10$, where the dimensionless parameter $α= h_{\rm rms}/δ$ is the ratio between the root-mean-square roughness amplitude and the penetration for the smooth surfaces case (Hertz contact). △ Less

Submitted 27 July, 2020; originally announced July 2020.

Comments: 6 pages, 5 figures. arXiv admin note: text overlap with arXiv:2007.13576

Fluid leakage in metallic seals

Authors: F. J. Fischer, K. Schmitz, A. Tiwari, B. N. J. Persson

Abstract: Metallic seals are crucial machine elements in many important applications, e.g., in ultrahigh vacuum systems. Due to the high elastic modulus of metals, and the surface roughness which exists on all solid surfaces, if no plastic deformation would occur one expects in most cases large fluid flow channels between the contacting metallic bodies, and large fluid leakage. However, in most applications… ▽ More Metallic seals are crucial machine elements in many important applications, e.g., in ultrahigh vacuum systems. Due to the high elastic modulus of metals, and the surface roughness which exists on all solid surfaces, if no plastic deformation would occur one expects in most cases large fluid flow channels between the contacting metallic bodies, and large fluid leakage. However, in most applications plastic deformation occurs, at least at the asperity level, which allows the surfaces to approach each other to such an extent that fluid leakage often can be neglected. In this study, we present an experimental set-up for studying the fluid leakage in metallic seals. We study the water leakage between a steel sphere and a steel body (seat) with a conical surface. The experimental results are found to be in good quantitative agreement with a (fitting-parameter-free) theoretical model. The theory predicts that the plastic deformations reduce the leak-rate by a factor $\approx 8$ △ Less

Submitted 27 July, 2020; originally announced July 2020.

Comments: 10 pages, 10 figures

Two comments on adhesion

Authors: A. Tiwari, J. Wang, B. N. J. Persson

Abstract: The adhesion paradox refers to the observation that for most solid objects no adhesion can be detected when they are separated from a state of molecular contact. The adhesion paradox results from surface roughness, and we present experimental and theoretical results which shows that adhesion in most cases is "killed" by the longest wavelength roughness. Adhesion experiments between a human finger… ▽ More The adhesion paradox refers to the observation that for most solid objects no adhesion can be detected when they are separated from a state of molecular contact. The adhesion paradox results from surface roughness, and we present experimental and theoretical results which shows that adhesion in most cases is "killed" by the longest wavelength roughness. Adhesion experiments between a human finger and a clean glass plate were carried out, and for a dry finger, no macroscopic adhesion occurred. We suggest that the observed decrease in the contact area with increasing shear force results from non-adhesive finger-glass contact mechanics, involving large deformations of a complex layered material. △ Less

Submitted 6 July, 2020; originally announced July 2020.

Comments: 6 Pages, 9 figures. arXiv admin note: text overlap with arXiv:2002.02226

Journal ref: Phys. Rev. E 102, 042803 (2020)

Cylinder-flat contact mechanics during sliding

Authors: J. Wang, A. Tiwari, I. M. Sivebaek, B. N. J. Persson

Abstract: Using molecular dynamics (MD) we study the dependency of the contact mechanics on the sliding speed when an elastic block (cylinder) with a ${\rm cos} (q_0 x)$ surface height profile is sliding in adhesive contact on a rigid flat substrate.The atoms on the block interact with the substrate atoms by Lennard-Jones (LJ) potentials, and we consider both commensurate and(nearly) incommensurate contacts… ▽ More Using molecular dynamics (MD) we study the dependency of the contact mechanics on the sliding speed when an elastic block (cylinder) with a ${\rm cos} (q_0 x)$ surface height profile is sliding in adhesive contact on a rigid flat substrate.The atoms on the block interact with the substrate atoms by Lennard-Jones (LJ) potentials, and we consider both commensurate and(nearly) incommensurate contacts. For the incommensurate system the friction force fluctuates between positive and negative values, with an amplitude proportional to the sliding speed, but with the average close to zero. For the commensurate system the (time-averaged) friction force is much larger and nearly velocity independent. For both type of systems the width of the contact region is velocity independent even when, for the commensurate case, the frictional shear stress increases from zero (before sliding) to $\approx 0.1 \ {\rm MPa}$ during sliding. This frictional shear stress, and the elastic modulus used, are typical for Polydimethylsiloxan (PDMS) rubber sliding on a glass surface, and we conclude that the reduction in the contact area observed in some experiments when increasing the tangential force must be due to effects not included in our model study, such as viscoelasticity or elastic nonlinearity △ Less

Submitted 2 July, 2020; originally announced July 2020.

Comments: 6 pages , 7 figures

Journal ref: Phys. Rev. E 102, 043002 (2020)

Plastic deformation of rough metallic surfaces

Authors: A. Tiwari, A. Almqvist, B. N. J. Persson

Abstract: We present experimental and theoretical results for the surface topography of a plastically deformed metallic (aluminum) block. When a hard spherical body (here a steel-, silica glass- or silicon nitride ball) with a smooth surface is indented in a metal block with a nominally flat, but still rough, surface, a spherical-cup-like indentation result due to plastic flow. The surface roughness in the… ▽ More We present experimental and theoretical results for the surface topography of a plastically deformed metallic (aluminum) block. When a hard spherical body (here a steel-, silica glass- or silicon nitride ball) with a smooth surface is indented in a metal block with a nominally flat, but still rough, surface, a spherical-cup-like indentation result due to plastic flow. The surface roughness in the indented region is, however, not entirely flattened. The long wavelength (macroasperity) content of the roughness result from the roughness on the original (aluminum) surface, but now plastically deformed. The roughness at short length scale, in the plastically deformed macroasperity contact regions, result from the roughness on the hard ball, and from inhomogeneous plastic flow. We model the contact mechanics using the boundary element method, combined with a simple numerical procedure to take into account the plastic flow. The theory can semi-quantitatively describe the modification of the roughness by the plastic flow. Since the fluid leakage of metallic seals in most cases is determined by the long wavelength roughness, we predict that the leakage can be estimated based on the elastoplastic contact mechanics model employed here. The plastic deformations of surfaces of some glassy polymers is very different from what we observed for aluminum, which we attribute to strong work-hardening and to inhomogeneous plastic flow for the polymers. Thus the numerical procedure to account for the plastic flow proposed here cannot be applied to glassy polymers in general. △ Less

Submitted 19 June, 2020; originally announced June 2020.

Comments: 10 pages, 18 figures

Dependency of Sliding Friction for Two Dimensional Systems on Electronegativity

Authors: Jianjun Wang, Avinash Tiwari, Yang Huang, Yu Jia, B. N. J. Persson

Abstract: We study the role of electronegativity in sliding friction for five different two dimensional (2D) monolayer systems using density functional theory (DFT) with van der Waals (vdW) corrections. We show that the friction between the commensurate 2D layered systems depends strongly on the electronegativity difference of the involved atoms. All the 2D layered structures exhibit almost the same magnitu… ▽ More We study the role of electronegativity in sliding friction for five different two dimensional (2D) monolayer systems using density functional theory (DFT) with van der Waals (vdW) corrections. We show that the friction between the commensurate 2D layered systems depends strongly on the electronegativity difference of the involved atoms. All the 2D layered structures exhibit almost the same magnitude of friction force when sliding along the nonpolar path, independent of the material and the surface structures. In contrast, for sliding friction along the polar path, the friction force obeys a universal linear scaling law as a function of the electronegativity difference of its constituent atoms. Further analyses demonstrate that atomic dipoles in the 2D monolayers induced by the electronegativity difference enhance the corrugation of charge distribution and increase the sliding barrier accordingly. Our studies reveal that electronegativity plays an important role in friction of low dimensional systems, and will provide a strategy for designing nanoscale devices further. △ Less

Submitted 14 June, 2020; originally announced June 2020.

Comments: manuscript 13 pages, 5 figures. Supporting Information 1 table and 1 figure

Interfacial fluid flow for systems with anisotropic roughness

Authors: B. N. J. Persson

Abstract: I discuss fluid flow at the interface between solids with anisotropic roughness. I show that for randomly rough surfaces with anisotropic roughness, the contact area percolate at the same relative contact area as for isotropic roughness, and that the Bruggeman effective medium theory and the critical junction theory give nearly the same results for the fluid flow conductivity. This shows that, in… ▽ More I discuss fluid flow at the interface between solids with anisotropic roughness. I show that for randomly rough surfaces with anisotropic roughness, the contact area percolate at the same relative contact area as for isotropic roughness, and that the Bruggeman effective medium theory and the critical junction theory give nearly the same results for the fluid flow conductivity. This shows that, in most cases, the surface roughness observed at high magnification is irrelevant for fluid flow problems such as the leakage of static seals, and fluid squeeze-out. △ Less

Submitted 4 March, 2020; originally announced March 2020.

Comments: 14 pages, 7 figures

On the origin of sliding friction: Role of lattice trapping

Authors: J. Wang, A. Tiwari, I. M. Sivebaek, B. N. J Persson

Abstract: Using molecular dynamics we study the dependence of the friction force on the sliding speed when an elastic slab (block) is sliding on a rigid substrate with a ${\rm sin} (q_0 x)$ surface height profile. The friction force is nearly velocity independent due to phonon emission at the closing and opening crack tips, where rapid atomic snap-in and -out events occur during sliding. The rapid events re… ▽ More Using molecular dynamics we study the dependence of the friction force on the sliding speed when an elastic slab (block) is sliding on a rigid substrate with a ${\rm sin} (q_0 x)$ surface height profile. The friction force is nearly velocity independent due to phonon emission at the closing and opening crack tips, where rapid atomic snap-in and -out events occur during sliding. The rapid events result from lattice trapping and are closely related to the velocity gap and hysteresis effects observed in model studies of crack propagation in solids. This indicates that the friction force is dominated by processes occurring at the edges of the contact area, which is confirmed by calculations showing that the friction force is independent of the normal force. The friction force increases drastically when the sliding velocity approaches the solid transverse sound velocity, as expected from the theory of cracks. △ Less

Submitted 20 February, 2020; originally announced February 2020.

Comments: 5 pages, 6 figures. arXiv admin note: text overlap with arXiv:2002.02226

Sphere and cylinder contact mechanics during slip

Authors: J. Wang, A. Tiwari, I. Sivebaek, B. N. J. Persson

Abstract: Using molecular dynamics (MD) we study the dependency of the contact mechanics on the sliding speed when an elastically soft slab (block) is sliding on a rigid substrate with a ${\rm sin} (q_0 x)$ surface height profile. The atoms on the block interact with the substrate atoms by Lennard-Jones potentials. We consider contacts with and without adhesion. We found that the contact area and the fricti… ▽ More Using molecular dynamics (MD) we study the dependency of the contact mechanics on the sliding speed when an elastically soft slab (block) is sliding on a rigid substrate with a ${\rm sin} (q_0 x)$ surface height profile. The atoms on the block interact with the substrate atoms by Lennard-Jones potentials. We consider contacts with and without adhesion. We found that the contact area and the friction force are nearly velocity independent for small velocities ($v < 0.25 \ {\rm m/s}$) in spite of the fact that the shear stress in the contact area is rather non-uniform. For the case of no adhesion the friction coefficient is very small. For the case of adhesion the friction coefficient is higher, and is mainly due to energy dissipation at the opening crack tip, where rapid atomic snap-off events occur during sliding. Adhesion experiments between a human finger and a clean glass plate were carried out, and for a dry finger no macroscopic adhesion occurred. We suggest that the observed decrease in the contact area with increasing shear force results from non-adhesive finger-glass contact mechanics, involving large deformations of a complex layered material. △ Less

Submitted 6 February, 2020; originally announced February 2020.

Comments: 14 pages, 20 Figures

Comment on "On the Origin of Frictional Energy Dissipation"

Authors: B. N. J. Persson

Abstract: In their interesting study (Ref. [1]) Hu et al have shown that for a simple "harmonium" solid model the slip-induced motion of surface atoms is close to critically damped. This result is in fact well known from studies of vibrational damping of atoms and molecules at surfaces. However, for real practical cases the situation may be much more complex and the conclusions of Hu et al invalid. In their interesting study (Ref. [1]) Hu et al have shown that for a simple "harmonium" solid model the slip-induced motion of surface atoms is close to critically damped. This result is in fact well known from studies of vibrational damping of atoms and molecules at surfaces. However, for real practical cases the situation may be much more complex and the conclusions of Hu et al invalid. △ Less

Submitted 16 December, 2019; originally announced December 2019.

Comments: 2 pages, 1 figure

On the role of flexoelectricity in triboelectricity for randomly rough surfaces

Authors: B. N. J. Persson

Abstract: I show how flexoelectricity result in a fluctuating surface electric potential when elastic solids with random roughness are squeezed into contact. The flexoelectric potential may induce surface charge distributions and hence contribute to triboelectricity. Using the developed theory I analyze the Kelvin Force Microscopy data of Baytekin et al for the electric potential above a polydimethylsiloxan… ▽ More I show how flexoelectricity result in a fluctuating surface electric potential when elastic solids with random roughness are squeezed into contact. The flexoelectric potential may induce surface charge distributions and hence contribute to triboelectricity. Using the developed theory I analyze the Kelvin Force Microscopy data of Baytekin et al for the electric potential above a polydimethylsiloxane (PDMS) surface after it was peeled away from another PDMS surface △ Less

Submitted 14 November, 2019; originally announced November 2019.

Comments: 6 pages and 4 figures

Electric field effect in heat transfer in 2D devices

Authors: A. I. Volokitin, B. N. J. Persson

Abstract: We calculate heat transfer between a 2D sheet (e.g. graphene) and a dielectric in presence of a gate voltage. The gate potential induces surface charge densities on the sheet and dielectric, which results in electric field, which is coupled to the surface displacements and, as a consequence, resulting an additional contributions to the radiative heat transfer. The electrostatic and van der Waals i… ▽ More We calculate heat transfer between a 2D sheet (e.g. graphene) and a dielectric in presence of a gate voltage. The gate potential induces surface charge densities on the sheet and dielectric, which results in electric field, which is coupled to the surface displacements and, as a consequence, resulting an additional contributions to the radiative heat transfer. The electrostatic and van der Waals interactions between the surface displacement result in the phonon heat transfer, which we calculate taking into account the nonlocality of these interactions. Numerical calculations are presented for heat transfer between graphene and a SiO$_2$ substrate. △ Less

Submitted 13 November, 2019; originally announced November 2019.

Comments: 10 pages, 2 figures

Journal ref: J. Phys.: Condens. Matter 32 (2020) 255301 (8pp)

Electroadhesion for soft adhesive pads and robotics: theory and numerical results

Authors: Bo N. J. Persson, Jianglong Guo

Abstract: Soft adhesive pads are needed for many robotics applications, and one approach is based on electroadhesion. Here we present a general analytic model and numerical results for electroadhesion for soft solids with arbitrary time-dependent applied voltage, and arbitrary dielectric response of the solids, and including surface roughness. We consider the simplest coplanar-plate-capacitor model with a p… ▽ More Soft adhesive pads are needed for many robotics applications, and one approach is based on electroadhesion. Here we present a general analytic model and numerical results for electroadhesion for soft solids with arbitrary time-dependent applied voltage, and arbitrary dielectric response of the solids, and including surface roughness. We consider the simplest coplanar-plate-capacitor model with a periodic array of conducting strips located close to the surface of the adhesive pad, and discuss the optimum geometrical arrangement to obtain the maximal electroadhesion force. For surfaces with roughness the (non-contact) gap between the solids will strongly influence the electroadhesion, and we show how the electroadhesion force can be calculated using a contact mechanics theory for elastic solids. The theory and models we present can be used to optimize the design of adhesive pads for robotics application. △ Less

Submitted 3 August, 2019; originally announced August 2019.

Theory for diffusive and ballistic air leakage and its application to suction cups

Authors: A. Tiwari, B. N. J. Persson

Abstract: We have developed a theory of air leakage at interfaces between two elastic solids with application to suction cups in contact with randomly rough surfaces. We present an equation for the airflow in narrow constrictions which interpolate between the diffusive and ballistic (Knudsen) air-flow limits. To test the theory we performed experiments using two different suction cups, made from soft polyvi… ▽ More We have developed a theory of air leakage at interfaces between two elastic solids with application to suction cups in contact with randomly rough surfaces. We present an equation for the airflow in narrow constrictions which interpolate between the diffusive and ballistic (Knudsen) air-flow limits. To test the theory we performed experiments using two different suction cups, made from soft polyvinylchloride (PVC), in contact with sandblasted polymethylmethacrylate (PMMA) plates. We found that the measured time to detatch (lifetime) of suction cups were in good agreement with theory, except for surfaces with the root-mean-square (rms) roughness below $\approx 1 \ {\rm μm}$, where diffusion of plasticizer from the PVC to the PMMA surface caused blockage of critical constrictions. Suction cup volume, stiffness and elastic modulus have a huge influence on the air leakage and hence the failure time of the cups. Based on our research we propose an improved biomimetic design of suction cups, that could show improved failure times in varying degree of roughness under dry and wet environments. △ Less

Submitted 3 June, 2019; originally announced June 2019.

Comments: 18 pages, 29 figures. arXiv admin note: substantial text overlap with arXiv:1905.09042

Physics of suction cups in air and in water

Authors: A. Tiwari, B. N. J. Persson

Abstract: We present experimental results for the dependency of the pull-off time (failure time) on the pull-off force for suction cups in the air and in water. The results are analyzed using a theory we have developed for the contact between suction cups and randomly rough surfaces. The theory predicts the dependency of the pull-off time (failure time) on the pull-off force, and is tested with measurements… ▽ More We present experimental results for the dependency of the pull-off time (failure time) on the pull-off force for suction cups in the air and in water. The results are analyzed using a theory we have developed for the contact between suction cups and randomly rough surfaces. The theory predicts the dependency of the pull-off time (failure time) on the pull-off force, and is tested with measurements performed on suction cups made from a soft polyvinyl chloride (PVC). As substrates we used sandblasted poly(methyl methacrylate) (PMMA). The theory is in good agreement with the experiments in air, except for surfaces with the root-mean-square (rms) roughness below $\approx 1 \ {\rm μm}$, where we observed lifetimes much longer than predicted by the theory. We show that this is due to out-diffusion of plasticizer from the soft PVC, which block the critical constrictions along the air flow channels. In water some deviation between theory and experiments is observed which may be due to capillary forces. We discuss the role of cavitation for the failure time of suction cups in water. △ Less

Submitted 13 November, 2020; v1 submitted 22 May, 2019; originally announced May 2019.

Comments: 11 pages, 16 figures

Influence of anisotropic surface roughness on lubricated rubber friction with application to hydraulic seals

Authors: M. Scaraggi, J. Angerhausen, L. Dorogin, H. Murrenhoff, B. N. J. Persson

Abstract: Machine elements and mechanical components have often surfaces with anisotropic roughness, which may result from the machining processes, e.g. grinding, or from wear. Hence, it is important to understand how surface roughness anisotropy affects contact mechanics properties, such as friction and the interface separation, which is important for lubricated contacts. Here we extend and apply a multisc… ▽ More Machine elements and mechanical components have often surfaces with anisotropic roughness, which may result from the machining processes, e.g. grinding, or from wear. Hence, it is important to understand how surface roughness anisotropy affects contact mechanics properties, such as friction and the interface separation, which is important for lubricated contacts. Here we extend and apply a multiscale mean-field model to the lubricated contact between a soft (e.g. rubber) elastic solid and a rigid countersurface. We consider surfaces with anisotropic surface roughness, and discuss how the fluid flow factors and friction factors depend on the roughness. We present an experimental study of the lubricated sliding contact between a nitrile butadiene rubber O-ring and steel surfaces with different types of isotropic and anisotropic surface roughness. The good quantitative comparison between the experimental results and the theory predictions suggests that the multiscale lubrication mechanisms are accurately captured by the theory. △ Less

Submitted 6 April, 2017; originally announced April 2017.

Elastohydrodynamics for soft solids with surface roughness: transient effects

Authors: M. Scaraggi, L. Dorogin, J. Angerhausen, H. Murrenhoff, B. N. J. Persson

Abstract: A huge number of technological and biological systems involves the lubricated contact between rough surfaces of soft solids in relative accelerated motion. Examples include dynamical rubber seals and the human joints. In this study we consider an elastic cylinder with random surface roughness in accelerated sliding motion on a rigid, perfectly flat (no roughness) substrate in a fluid. We calculate… ▽ More A huge number of technological and biological systems involves the lubricated contact between rough surfaces of soft solids in relative accelerated motion. Examples include dynamical rubber seals and the human joints. In this study we consider an elastic cylinder with random surface roughness in accelerated sliding motion on a rigid, perfectly flat (no roughness) substrate in a fluid. We calculate the surface deformations, interface separation and the contributions to the friction force and the normal force from the area of real contact and from the fluid. The driving velocity profile as a function of time is assumed to be either a sine-function, or a linear multi-ramp function. We show how the squeeze-in and squeeze-out processes, occurring in accelerated sliding, quantitatively affect the Stribeck curve with respect to the steady sliding. Finally, the theory results are compared to experimental data. △ Less

Submitted 7 February, 2017; originally announced February 2017.

Quantum Vavilov-Cherenkov radiation from a small neutral particle moving parallel to a transparent dielectric plate

Authors: A. I. Volokitin, B. N. J. Persson

Abstract: We study the quantum Vavilov-Cherenkov (QVC) radiation and quantum friction occurring during motion of a small neutral particle parallel to a transparent dielectric plate with the refractive index $n$. This phenomenon occurs above the threshold velocity $v_c=c/n$. The particle acceleration and rate of heating are determined by the friction force and heating power in the rest reference frame of the… ▽ More We study the quantum Vavilov-Cherenkov (QVC) radiation and quantum friction occurring during motion of a small neutral particle parallel to a transparent dielectric plate with the refractive index $n$. This phenomenon occurs above the threshold velocity $v_c=c/n$. The particle acceleration and rate of heating are determined by the friction force and heating power in the rest reference frame of the particle. We calculate these quantities starting from the expressions for the friction force and the radiative energy transfer in the plate-plate configuration, assuming plate at the rest in the \textit{lab} frame rarefied. Close to the light velocity there is a big difference between the friction force and the radiation power in the rest frame of a particle and in the \textit{lab} reference frame. This difference is connected with the change of the rest mass of the particle due to absorption of radiation. Close to the threshold velocity the decrease of the kinetic energy of the particle is determined mainly by radiation power in in the \textit{lab} frame. However, close to the light velocity it is determined also by the heating power for the particle. We establish the connections between the quantities in the different reference frames. For a nanoparticle the QVC radiation intensity can be comparable to classical one. We discuss the possibility to detect QVC radiation. △ Less

Submitted 7 March, 2016; v1 submitted 14 December, 2015; originally announced December 2015.

Comments: 7 pages, 2 figures. arXiv admin note: text overlap with arXiv:1511.06573

Journal ref: JETP Letters, V.103,228(2016)

On the dependency of rubber friction on the normal force or load: theory and experiment

Authors: G. Fortunato, V. Ciaravola, A. Furno, M. Scaraggi, B. Lorenz, B. N. J. Persson

Abstract: In rubber friction studies it is often observed that the kinetic friction coefficient μ depends on the nominal contact pressure p. We discuss several possible origins of the pressure dependency of μ: (a) saturation of the contact area (and friction force) due to high nominal squeezing pressure, (b) non-linear viscoelasticity, (c) non-randomness in the surface topography, in particular the influenc… ▽ More In rubber friction studies it is often observed that the kinetic friction coefficient μ depends on the nominal contact pressure p. We discuss several possible origins of the pressure dependency of μ: (a) saturation of the contact area (and friction force) due to high nominal squeezing pressure, (b) non-linear viscoelasticity, (c) non-randomness in the surface topography, in particular the influence of the skewness of the surface roughness profile, (d) adhesion, and (e) frictional heating. We show that in most cases the non-linearity in the μ(p) relation is mainly due to process (e) (frictional heating), which softens the rubber, increases the area of contact, and (in most cases) reduces the viscoelastic contribution to the friction. In fact, since the temperature distribution in the rubber at time t depends on on the sliding history (i.e., on the earlier time t0 < t), the friction coefficient at time t will also depend on the sliding history, i.e. it is, strictly speaking, a time integral operator. The energy dissipation in the contact regions between solids in sliding contact can result in high local temperatures which may strongly affect the area of real contact and the friction force (and the wear-rate). This is the case for rubber sliding on road surfaces at speeds above 1 mm/s. In Ref. [14] we have derived equations which describe the frictional heating for solids with arbitrary thermal properties. In this paper the theory is applied to rubber friction on road surfaces. Numerical results are presented and compared to experimental data. We observe good agreement between the calculated and measured temperature increase. △ Less

Submitted 4 December, 2015; originally announced December 2015.

Comments: 14 pages, 21 figures

Quantum Vavilov-Cherenkov radiation from shearing two transparent dielectric plates

Authors: A. I. Volokitin, B. N. J Persson

Abstract: Using a fully relativistic theory we study the quantum Vavilov-Cherenkov radiation and quantum friction occurring during relative sliding of the two transparent dielectric plates with the refractive index $n$. These phenomena occur above the threshold velocity $v_c=2nc/(n^2+1)$. Close to the threshold velocity they are dominated by the contribution from $s$--polarized electromagnetic waves, which… ▽ More Using a fully relativistic theory we study the quantum Vavilov-Cherenkov radiation and quantum friction occurring during relative sliding of the two transparent dielectric plates with the refractive index $n$. These phenomena occur above the threshold velocity $v_c=2nc/(n^2+1)$. Close to the threshold velocity they are dominated by the contribution from $s$--polarized electromagnetic waves, which agrees with the approximate (relativistic) theory by Pendry (J. Mod. Opt. \textbf{45}, 2389 (1998)). However, in the ultra relativistic case ($v\rightarrow c$), the contributions from both polarisations are strongly enhanced in the comparison with the approximate theory, and a new contribution occurs from the mixing of the electromagnetic waves with the different polarization. The numerical results are supplemented by an analytical treatment close to the threshold velocity and the light velocity. △ Less

Submitted 11 December, 2015; v1 submitted 20 November, 2015; originally announced November 2015.

Comments: 7 pages, 3 figures

Journal ref: Phys. Rev. B 93, 035407 (2016)

Fluid contact angle on solid surfaces: role of multiscale surface roughness

Authors: Francesco Bottiglione, Giuseppe Carbone, Bo N. J. Persson

Abstract: We present a simple analytical model and an exact numerical study which explain the role of roughness on different length scales for the fluid contact angle on rough solid surfaces. We show that there is no simple relation between the distribution of surface slopes and the fluid contact angle. In particular, surfaces with the same distribution of slopes may exhibit very different contact angles de… ▽ More We present a simple analytical model and an exact numerical study which explain the role of roughness on different length scales for the fluid contact angle on rough solid surfaces. We show that there is no simple relation between the distribution of surface slopes and the fluid contact angle. In particular, surfaces with the same distribution of slopes may exhibit very different contact angles depending on the range of length-scales over which the surfaces have roughness. △ Less

Submitted 17 August, 2015; originally announced August 2015.

General contact mechanics theory for randomly rough surfaces with application to rubber friction

Authors: Michele Scaraggi, Bo N. J. Persson

Abstract: We generalize the Persson contact mechanics and rubber friction theory to the case where both surfaces have surface roughness. The solids can be rigid, elastic or viscoelastic, and can be homogeneous or layered. We calculate the contact area, the viscoelastic contribution to the friction force, and the average interfacial separation as a function of the sliding speed and the nominal contact pressu… ▽ More We generalize the Persson contact mechanics and rubber friction theory to the case where both surfaces have surface roughness. The solids can be rigid, elastic or viscoelastic, and can be homogeneous or layered. We calculate the contact area, the viscoelastic contribution to the friction force, and the average interfacial separation as a function of the sliding speed and the nominal contact pressure. We illustrate the theory with numerical results for a rubber block sliding on a road surface. We find that with increasing sliding speed, the influence of the roughness on the rubber block decreases, and for typical sliding speeds involved in tire dynamics it can be neglected. △ Less

Submitted 23 June, 2015; originally announced June 2015.

Near-field radiative heat transfer between closely spaced graphene and amorphous SiO$_2$

Authors: A. I. Volokitin, B. N. J. Persson

Abstract: We study the near-field radiative energy transfer between graphene and an amorphous SiO$_2$ substrate. In comparison with the existing theories of near-field radiative heat transfer our theory takes into account that the free carriers in graphene are moving relative to the substrate with a drift velocity $v$. In this case the heat flux is determined by both thermal and quantum fluctuations. We fin… ▽ More We study the near-field radiative energy transfer between graphene and an amorphous SiO$_2$ substrate. In comparison with the existing theories of near-field radiative heat transfer our theory takes into account that the free carriers in graphene are moving relative to the substrate with a drift velocity $v$. In this case the heat flux is determined by both thermal and quantum fluctuations. We find that quantum fluctuations give an important contribution to the radiative energy transfer for low temperatures and high electric field (large drift velocities). For nonsuspended graphene the near-field radiative energy transfer gives a significant contribution to the heat transfer, in addition to the contribution from phononic coupling. For suspended graphene (large separation) the corresponding radiative energy transfer coefficient at nanoscale gap is $\sim$ 3 orders of magnitude larger than radiative heat transfer coefficient of the blackbody radiation limit. △ Less

Submitted 2 September, 2014; originally announced September 2014.

Comments: 4 pages, 2 figures. arXiv admin note: text overlap with arXiv:1112.4912, arXiv:1012.5212, arXiv:1409.0145

Journal ref: Phys.Rev. B 83(2011)241407(R)

Quantum friction

Authors: A. I. Volokitin, B. N. J. Persson

Abstract: We investigate the van der Waals friction between graphene and an amorphous SiO$_2$ substrate. We find that due to this friction the electric current is saturated at a high electric field, in agreement with experiment. The saturation current depends weakly on the temperature, which we attribute to the quantum friction between the graphene carriers and the substrate optical phonons. We calculate al… ▽ More We investigate the van der Waals friction between graphene and an amorphous SiO$_2$ substrate. We find that due to this friction the electric current is saturated at a high electric field, in agreement with experiment. The saturation current depends weakly on the temperature, which we attribute to the quantum friction between the graphene carriers and the substrate optical phonons. We calculate also the frictional drag between two graphene sheets caused by van der Waals friction, and find that this drag can induce a voltage high enough to be easily measured experimentally. △ Less

Submitted 30 August, 2014; originally announced September 2014.

Comments: 4 pages, 3 figures. arXiv admin note: substantial text overlap with arXiv:1012.5212, arXiv:1112.4912

Report number: Report no:Samgtu-12

Journal ref: Phys.Rev.Lett.106,094502(2011)

Viscoelastic contact mechanics between randomly rough surfaces

Authors: Michele Scaraggi, Bo N. J. Persson

Abstract: We present exact numerical results for the friction force and the contact area for a viscoelastic solid (rubber) in sliding contact with hard, randomly rough substrates. The rough surfaces are self-affine fractal with roughness over several decades in length scales. We calculate the contribution to the friction from the pulsating deformations induced by the substrate asperities. We also calculate… ▽ More We present exact numerical results for the friction force and the contact area for a viscoelastic solid (rubber) in sliding contact with hard, randomly rough substrates. The rough surfaces are self-affine fractal with roughness over several decades in length scales. We calculate the contribution to the friction from the pulsating deformations induced by the substrate asperities. We also calculate how the area of real contact, $A(v,p) $, depends on the sliding speed $v$ and on the nominal contact pressure $p$, and we show how the contact area for any sliding speed can be obtained from a universal master curve $A(p)$. The numerical results are found to be in good agreement with the predictions of an analytical contact mechanics theory. △ Less

Submitted 27 June, 2014; originally announced June 2014.

Comments: 5 pages

Theory of adhesion: role of surface roughness

Authors: Bo N. J. Persson, Michele Scaraggi

Abstract: We discuss how surface roughness influence the adhesion between elastic solids. We introduce a Tabor number which depends on the length scale or magnification, and which gives information about the nature of the adhesion at different length scales. We consider two limiting cases relevant for (a) elastically hard solids with weak adhesive interaction (DMT-limit) and (b) elastically soft solids or s… ▽ More We discuss how surface roughness influence the adhesion between elastic solids. We introduce a Tabor number which depends on the length scale or magnification, and which gives information about the nature of the adhesion at different length scales. We consider two limiting cases relevant for (a) elastically hard solids with weak adhesive interaction (DMT-limit) and (b) elastically soft solids or strong adhesive interaction (JKR-limit). For the former cases we study the nature of the adhesion using different adhesive force laws ($F\sim u^{-n}$, $n=1.5-4$, where $u$ is the wall-wall separation). In general, adhesion may switch from DMT-like at short length scales to JKR-like at large (macroscopic) length scale. We compare the theory predictions to the results of exact numerical simulations and find good agreement between theory and the simulation results. △ Less

Submitted 13 May, 2014; originally announced May 2014.

Comment on "Fully covariant radiation force on a polarizable particle"

Authors: A. I. Volokitin, B. N. J. Persson

Abstract: Recently Pieplow and Henkel (PH) (NJP \textbf{15} (2013) 023027) presented a new fully covariant theory of the Casimir friction force acting on small neutral particle moving parallel to flat surface. We compare results of this theory with results which follow from a fully relativistic theory of friction in plate-plate configurations in the limit when one plate is considered as sufficiently rarefie… ▽ More Recently Pieplow and Henkel (PH) (NJP \textbf{15} (2013) 023027) presented a new fully covariant theory of the Casimir friction force acting on small neutral particle moving parallel to flat surface. We compare results of this theory with results which follow from a fully relativistic theory of friction in plate-plate configurations in the limit when one plate is considered as sufficiently rarefied. We show that there is the agreement between these theories. △ Less

Submitted 22 July, 2014; v1 submitted 11 May, 2014; originally announced May 2014.

Comments: 8 pages. arXiv admin note: substantial text overlap with arXiv:0807.1004, arXiv:1005.4296

Journal ref: New Journal of Physics 16 (2014) 118001

Self-Affine Elastic Contacts: Percolation and Leakage

Authors: Wolf B. Dapp, Andreas Lücke, Bo N. J. Persson, Martin H. Müser

Abstract: We study fluid flow at the interfaces between elastic solids with randomly rough, self-affine surfaces. We show by numerical simulation that elastic deformation lowers the relative contact area at which contact patches percolate in comparison to traditional approaches to seals. Elastic deformation also suppresses leakage through contacts even far away from the percolation threshold. Reliable estim… ▽ More We study fluid flow at the interfaces between elastic solids with randomly rough, self-affine surfaces. We show by numerical simulation that elastic deformation lowers the relative contact area at which contact patches percolate in comparison to traditional approaches to seals. Elastic deformation also suppresses leakage through contacts even far away from the percolation threshold. Reliable estimates for leakage can be obtained by combining Persson's contact mechanics theory with a slightly modified version of Bruggeman's effective-medium solution of the Reynolds equation. △ Less

Submitted 15 August, 2013; originally announced August 2013.

Comments: 4 pages, 3 figures

Journal ref: Phys. Rev. Lett. 108, 244301 (2012)

Contact electrification and the work of adhesion

Authors: B. N. J. Persson, M. Scaraggi, A. I. Volokitin

Abstract: We present a general theory for the contribution from contact electrification to the work necessary to separate two solid bodies. The theory depends on the surface charge density correlation function, which we deduce from Kelvin Force Microscopy (KFM) maps of the surface electrostatic potential. For silicon rubber (polydimethylsiloxane, PDMS) we discuss in detail the relative importance of the dif… ▽ More We present a general theory for the contribution from contact electrification to the work necessary to separate two solid bodies. The theory depends on the surface charge density correlation function, which we deduce from Kelvin Force Microscopy (KFM) maps of the surface electrostatic potential. For silicon rubber (polydimethylsiloxane, PDMS) we discuss in detail the relative importance of the different contributions to the observed work of adhesion. △ Less

Submitted 13 May, 2013; originally announced May 2013.

Comments: 5 pages, 2 figures

On the validity of the method of reduction of dimensionality: area of contact, average interfacial separation and contact stiffness

Authors: I. A. Lyashenko, Lars Pastewka, Bo N. J. Persson

Abstract: It has recently been suggested that many contact mechanics problems between solids can be accurately studied by mapping the problem on an effective one dimensional (1D) elastic foundation model. Using this 1D mapping we calculate the contact area and the average interfacial separation between elastic solids with nominally flat but randomly rough surfaces. We show, by comparison to exact numerical… ▽ More It has recently been suggested that many contact mechanics problems between solids can be accurately studied by mapping the problem on an effective one dimensional (1D) elastic foundation model. Using this 1D mapping we calculate the contact area and the average interfacial separation between elastic solids with nominally flat but randomly rough surfaces. We show, by comparison to exact numerical results, that the 1D mapping method fails even qualitatively. We also calculate the normal interfacial stiffness $K$ and compare it with the result of an analytical study. We attribute the failure of the elastic foundation model to the neglect of the long-range elastic coupling between the asperity contact regions. △ Less

Submitted 5 March, 2013; originally announced March 2013.

Comments: 5 pages, 4 figures, 29 references

Journal ref: Tribol. Lett. 52, 223 (2013)