-
Cyclic solid-state quantum battery: Thermodynamic characterization and quantum hardware simulation
Authors:
Luca Razzoli,
Giulia Gemme,
Ilia Khomchenko,
Maura Sassetti,
Henni Ouerdane,
Dario Ferraro,
Giuliano Benenti
Abstract:
We introduce a cyclic quantum battery model, based on an interacting bipartite system, weakly coupled to a thermal bath. The working cycle of the battery consists of four strokes: system thermalization, disconnection of subsystems, ergotropy extraction, and reconnection. The thermal bath acts as a charger in the thermalization stroke, while ergotropy extraction is possible because the ensuing ther…
▽ More
We introduce a cyclic quantum battery model, based on an interacting bipartite system, weakly coupled to a thermal bath. The working cycle of the battery consists of four strokes: system thermalization, disconnection of subsystems, ergotropy extraction, and reconnection. The thermal bath acts as a charger in the thermalization stroke, while ergotropy extraction is possible because the ensuing thermal state is no longer passive after the disconnection stroke. Focusing on the case of two interacting qubits, we show that phase coherence, in the presence of non-trivial correlations between the qubits, can be exploited to reach working regimes with efficiency higher than 50% while providing finite ergotropy. Our protocol is illustrated through a simple and feasible circuit model of a cyclic superconducting quantum battery. Furthermore, we simulate the considered cycle on superconducting IBM quantum machines. The good agreement between the theoretical and simulated results strongly suggests that our scheme for cyclic quantum batteries can be successfully realized in superconducting quantum hardware.
△ Less
Submitted 19 January, 2025; v1 submitted 9 July, 2024;
originally announced July 2024.
-
Influence of the Anderson transition on thermoelectric energy conversion in disordered electronic systems
Authors:
I. Khomchenko,
H. Ouerdane,
G. Benenti
Abstract:
So far, the efficiency of thermoelectric energy conversion remains low compared to traditional technologies, such as coal or nuclear. This low efficiency can be explained by connecting the thermoelastic properties of the electronic working fluid to its transport properties. Such connection also shows that operating close to electronic phase transitions can be an efficient way to boost the thermoel…
▽ More
So far, the efficiency of thermoelectric energy conversion remains low compared to traditional technologies, such as coal or nuclear. This low efficiency can be explained by connecting the thermoelastic properties of the electronic working fluid to its transport properties. Such connection also shows that operating close to electronic phase transitions can be an efficient way to boost the thermoelectric energy conversion. In this paper, we analyze thermoelectric efficiency close to the metal-insulator Anderson transition. Our results reveal the direct link between the thermoelectric and thermoelastic properties of Anderson-type systems. Moreover, the role of the conductivity critical exponent in the thermoelectric energy conversion is analysed. Finally, we show that relatively large values of the thermoelectric figure of merit may be obtained in the vicinity of the Anderson transition.
△ Less
Submitted 27 February, 2024; v1 submitted 3 July, 2023;
originally announced July 2023.
-
Voltage-amplified heat rectification in SIS junctions
Authors:
Ilia Khomchenko,
Henni Ouerdane,
Giuliano Benenti
Abstract:
The control of thermal fluxes -- magnitude and direction, in mesoscale and nanoscale electronic circuits can be achieved by means of heat rectification using thermal diodes in two-terminal systems. The rectification coefficient $\mathcal{R}$, given by the ratio of forward and backward heat fluxes, varies with the design of the diode and the working conditions under which the system operates. A val…
▽ More
The control of thermal fluxes -- magnitude and direction, in mesoscale and nanoscale electronic circuits can be achieved by means of heat rectification using thermal diodes in two-terminal systems. The rectification coefficient $\mathcal{R}$, given by the ratio of forward and backward heat fluxes, varies with the design of the diode and the working conditions under which the system operates. A value of $\mathcal{R}\ll 1$ or $\mathcal{R}\gg 1$ is a signature of high heat rectification performance but current solutions allowing such ranges, necessitate rather complex designs. Here, we propose a simple solution: the use of a superconductor-insulator-superconductor (SIS) junction under an applied fast oscillating (THz range) voltage as the control of the heat flow direction and magnitude can be done by tuning the initial value of the superconducting phase. Our theoretical model based on the Green functions formalism and coherent transport theory, shows a possible sharp rise of the heat rectification coefficient with values up to $\mathcal{R} \approx 500$ beyond the adiabatic regime. The influence of quantum coherent effects on heat rectification in the SIS junction is highlighted.
△ Less
Submitted 13 December, 2022; v1 submitted 18 June, 2022;
originally announced June 2022.
-
The thermoelectric conversion efficiency problem: Insights from the electron gas thermodynamics close to a phase transition
Authors:
I. Khomchenko,
A. Ryzhov,
F. Maculewicz,
F. Kurth,
R. Hühne,
A. Golombek,
M. Schleberger,
C. Goupil,
Ph. Lecoeur,
A. Böhmer,
G. Benenti,
G. Schierning,
H. Ouerdane
Abstract:
The bottleneck in modern thermoelectric power generation and cooling is the low energy conversion efficiency of thermoelectric materials. The detrimental effects of lattice phonons on performance can be mitigated, but achieving a high thermoelectric power factor remains a major problem because the Seebeck coefficient and electrical conductivity cannot be jointly increased. The conducting electron…
▽ More
The bottleneck in modern thermoelectric power generation and cooling is the low energy conversion efficiency of thermoelectric materials. The detrimental effects of lattice phonons on performance can be mitigated, but achieving a high thermoelectric power factor remains a major problem because the Seebeck coefficient and electrical conductivity cannot be jointly increased. The conducting electron gas in thermoelectric materials is the actual working fluid that performs the energy conversion, so its properties determine the maximum efficiency that can theoretically be achieved. By relating the thermoelastic properties of the electronic working fluid to its transport properties (considering noninteracting electron systems), we show why the performance of conventional semiconductor materials is doomed to remain low. Analyzing the temperature dependence of the power factor theoretically in 2D systems and experimentally in a thin film, we find that in the fluctuation regimes of an electronic phase transition, the thermoelectric power factor can significantly increase owing to the increased compressibility of the electron gas. We also calculate the ideal thermoelectric conversion efficiency in noninteracting electron systems across a wide temperature range neglecting phonon effects and dissipative coupling to the heat source and sink. Our results show that driving the electronic system to the vicinity of a phase transition can indeed be an innovative route to strong efficiency enhancement, but at the cost of an extremely narrow temperature range for the use of such materials, which in turn precludes potential development for the desired wide range of thermoelectric energy conversion applications.
△ Less
Submitted 14 October, 2024; v1 submitted 21 October, 2021;
originally announced October 2021.
-
SQUID-based interferometric accelerometer
Authors:
Ilia Khomchenko,
Patrick Navez,
Henni Ouerdane
Abstract:
Optics and more recently coherent matter waves enabled inertial sensors such as accelerometers and gyroscopes to reach high levels of resolution and sensitivity. As these technologies rest on physical phenomena that require particular setups and working conditions such as, e.g., kilometers of optical fibers or ultralow temperatures, their application range is limited because of lack of portability…
▽ More
Optics and more recently coherent matter waves enabled inertial sensors such as accelerometers and gyroscopes to reach high levels of resolution and sensitivity. As these technologies rest on physical phenomena that require particular setups and working conditions such as, e.g., kilometers of optical fibers or ultralow temperatures, their application range is limited because of lack of portability. Here, we propose a path forward considering a superconducting quantum interference device (SQUID) to detect and measure acceleration, using electronic interferometry. The operation of such an accelerometer rests on the ability of the Cooper pairs to record their wave function phase change as the device is subjected either to a transverse acceleration or vibrations. We provide numerical evidence for the feasibility of SQUID-based accelerometers that can be used for transverse acceleration and oscillatory motion measurement.
△ Less
Submitted 16 October, 2022; v1 submitted 25 August, 2021;
originally announced August 2021.
-
Non-rotational mechanism of polarization in alcohols
Authors:
V. G. Artemov,
A. Ryzhov,
E. Carlsen,
P. O. Kapralov,
H. Ouerdane
Abstract:
Chemical polarity governs various mechanical, chemical and thermodynamic properties of dielectrics. Polar liquids have been amply studied, yet the basic mechanisms underpinning their dielectric properties remain not fully understood, as standard models following Debye's phenomenological approach do not account for quantum effects and cannot aptly reproduce the full dc-up-to-THz spectral range. Her…
▽ More
Chemical polarity governs various mechanical, chemical and thermodynamic properties of dielectrics. Polar liquids have been amply studied, yet the basic mechanisms underpinning their dielectric properties remain not fully understood, as standard models following Debye's phenomenological approach do not account for quantum effects and cannot aptly reproduce the full dc-up-to-THz spectral range. Here, using the illustrative case of monohydric alcohols, we show that deep tunneling and the consequent intermolecular separation of excess protons and "proton-holes" in the polar liquids govern their static and dynamic dielectric properties on the same footing. We performed systematic ultrabroadband (0-10 THz) spectroscopy experiments with monohydric alcohols of different (0.4-1.6 nm) molecular lengths, and show that the finite lifetime of molecular species, and the proton-hole correlation length are the two principle parameters responsible for the dielectric response of all the studied alcohols across the entire frequency range. Our results demonstrate that a quantum non-rotational intermolecular mechanism drives the polarization in alcohols while the rotational mechanism of molecular polarization plays a secondary role, manifesting itself in the sub-terahertz region only.
△ Less
Submitted 14 December, 2020; v1 submitted 17 June, 2020;
originally announced June 2020.
-
Thermodynamics of animal locomotion
Authors:
E. Herbert,
H. Ouerdane,
Ph. Lecoeur,
V. Bels,
C. Goupil
Abstract:
Muscles are biological actuators extensively studied in the frame of Hill's classic empirical model as isolated biomechanical entities, which hardly applies to a living organism subjected to physiological and environmental constraints. Here we elucidate the overarching principle of a \emph{living} muscle action for locomotion, considering it from the thermodynamic viewpoint as an assembly of actua…
▽ More
Muscles are biological actuators extensively studied in the frame of Hill's classic empirical model as isolated biomechanical entities, which hardly applies to a living organism subjected to physiological and environmental constraints. Here we elucidate the overarching principle of a \emph{living} muscle action for locomotion, considering it from the thermodynamic viewpoint as an assembly of actuators (muscle units) connected in parallel, operating via chemical-to-mechanical energy conversion under mixed (potential and flux) boundary conditions. Introducing the energy cost of effort, $COE_-$, as the generalization of the well-known oxygen cost of transport, $COT$, in the frame of our compact locally linear non-equilibrium thermodynamics model, we analyze oxygen consumption measurement data from a documented experiment on energy cost management and optimization by horses moving at three different gaits. Horses adapt to a particular gait by mobilizing a nearly constant number of muscle units minimizing waste production per unit distance covered; this number significantly changes during transition between gaits. The mechanical function of the animal is therefore determined both by its own thermodynamic characteristics and by the metabolic operating point of the locomotor system.
△ Less
Submitted 25 November, 2020; v1 submitted 6 April, 2020;
originally announced April 2020.
-
Revealing excess protons in the infrared spectrum of liquid water
Authors:
V. G. Artemov,
E. Uykur,
S. Roh,
A. V. Pronin,
H. Ouerdane,
M. Dressel
Abstract:
The most common species in liquid water, next to neutral H$_2$O molecules, are the H$_3$O$^+$ and OH$^-$ ions. In a dynamic picture, their exact concentrations depend on the time scale at which these are probed. Here, using a spectral-weight analysis, we experimentally resolve the fingerprints of the elusive fluctuations-born short-living H$_3$O$^+$, DH$_2$O$^+$, HD$_2$O$^+$, and D$_3$O$^+$ ions i…
▽ More
The most common species in liquid water, next to neutral H$_2$O molecules, are the H$_3$O$^+$ and OH$^-$ ions. In a dynamic picture, their exact concentrations depend on the time scale at which these are probed. Here, using a spectral-weight analysis, we experimentally resolve the fingerprints of the elusive fluctuations-born short-living H$_3$O$^+$, DH$_2$O$^+$, HD$_2$O$^+$, and D$_3$O$^+$ ions in the IR spectra of light (H$_2$O), heavy (D$_2$O), and semi-heavy (HDO) water. We find that short-living ions, with concentrations reaching $\sim 2\%$ of the content of water molecules, coexist with long-living pH-active ions on the picosecond timescale, thus making liquid water an effective ionic liquid in femtochemistry.
△ Less
Submitted 9 July, 2020; v1 submitted 16 October, 2019;
originally announced October 2019.
-
Variational autoencoder reconstruction of complex many-body physics
Authors:
I. Luchnikov,
A. Ryzhov,
P. -J. C. Stas,
S. N. Filippov,
H. Ouerdane
Abstract:
Given the notably increasing complexity of mathematical models to study realistic systems and their coupling to their environment that constrains their dynamics, both analytical approaches and numerical methods that build on these models, show limitations in scope or applicability. On the other hand, machine learning, i.e. data-driven, methods prove to be increasingly efficient for the study of co…
▽ More
Given the notably increasing complexity of mathematical models to study realistic systems and their coupling to their environment that constrains their dynamics, both analytical approaches and numerical methods that build on these models, show limitations in scope or applicability. On the other hand, machine learning, i.e. data-driven, methods prove to be increasingly efficient for the study of complex quantum systems. Deep neural networks in particular have been successfully applied to many-body quantum dynamics simulations and to quantum matter phase characterization. In the present work, we show how to use a variational autoencoder (VAE) -- a state-of-the-art tool in the field of deep learning for the simulation of probability distributions of complex systems. More precisely, we transform a quantum mechanical problem of many-body state reconstruction into a statistical problem, suitable for VAE, by using informationally complete positive operator-valued measure. We show with the paradigmatic quantum Ising model in a transverse magnetic field, that the ground-state physics, such as, e.g., magnetization and other mean values of observables, of a whole class of quantum many-body systems can be reconstructed by using VAE learning of tomographic data, for different parameters of the Hamiltonian, and even if the system undergoes a quantum phase transition. We also discuss challenges related to our approach as entropy calculations pose particular difficulties.
△ Less
Submitted 9 October, 2019;
originally announced October 2019.
-
Thermodynamics of metabolic energy conversion under muscle load
Authors:
C. Goupil,
H. Ouerdane,
E. Herbert,
Y. D'Angelo,
C. Goupil
Abstract:
The metabolic processes complexity is at the heart of energy conversion in living organisms and forms a huge obstacle to develop tractable thermodynamic metabolism models. By raising our analysis to a higher level of abstraction, we develop a compact -- i.e. relying on a reduced set of parameters -- thermodynamic model of metabolism, in order to analyze the chemical-to-mechanical energy conversion…
▽ More
The metabolic processes complexity is at the heart of energy conversion in living organisms and forms a huge obstacle to develop tractable thermodynamic metabolism models. By raising our analysis to a higher level of abstraction, we develop a compact -- i.e. relying on a reduced set of parameters -- thermodynamic model of metabolism, in order to analyze the chemical-to-mechanical energy conversion under muscle load, and give a thermodynamic ground to Hill's seminal muscular operational response model. Living organisms are viewed as dynamical systems experiencing a feedback loop in the sense that they can be considered as thermodynamic systems subjected to mixed boundary conditions, coupling both potentials and fluxes. Starting from a rigorous derivation of generalized thermoelastic and transport coefficients, leading to the definition of a metabolic figure of merit, we establish the expression of the chemical-mechanical coupling, and specify the nature of the dissipative mechanism and the so called figure of merit. The particular nature of the boundary conditions of such a system reveals the presence of a feedback resistance, representing an active parameter, which is crucial for the proper interpretation of the muscle response under effort in the framework of Hill's model. We also develop an exergy analysis of the so-called maximum power principle, here understood as a particular configuration of an out-of-equilibrium system, with no supplemental extremal principle involved.
△ Less
Submitted 29 January, 2019; v1 submitted 10 August, 2017;
originally announced August 2017.
-
Radiolysis of water confined in porous silica: A simulation study of the physicochemical yields
Authors:
H. Ouerdane,
B. Gervais,
H. Zhou,
M. Beuve,
J. -Ph. Renault
Abstract:
We investigate the radiolysis of liquid water confined in a porous silica matrix by means of an event-by-event Monte Carlo simulation of electron penetration in this composite system. We focus on the physical and physicochemical effects that take place in the picosecond range, before the radicals start to diffuse and react. We determine the radiolytic yields of the primary species for a system mad…
▽ More
We investigate the radiolysis of liquid water confined in a porous silica matrix by means of an event-by-event Monte Carlo simulation of electron penetration in this composite system. We focus on the physical and physicochemical effects that take place in the picosecond range, before the radicals start to diffuse and react. We determine the radiolytic yields of the primary species for a system made of cylindrical pores filled with water over a wide range of pore radii $R_{\rm C}$. We show that the relative position of the conduction band edge $V_0$ in both materials plays a major role in the radiolysis of composite systems. Due to its lower $V_0$ as compared to that of silica, water acts as a collector of low-energy electrons, which leads to a huge enhancement of the solvated electron yields for $R_{\rm C} \leq$ 100 nm. The confinement has also a marked effect on the spatial distribution of the radicals, which become isolated in a very large number of pores as $R_{\rm C}$ decreases.
△ Less
Submitted 27 December, 2016;
originally announced December 2016.
-
True nature of the Curzon-Ahlborn efficiency
Authors:
Yann Apertet,
Henni Ouerdane,
Christophe Goupil,
Philippe Lecoeur
Abstract:
The Curzon-Ahlborn efficiency has long served as the definite upper bound for the thermal efficiency at maximum output power, and has thus shaped the development of finite-time thermodynamics. In this paper, we repeal the ruling consensus according to which it has a genuine universal character that can be derived from linear irreversible thermodynamics. We demonstrate that the Curzon-Ahlborn effic…
▽ More
The Curzon-Ahlborn efficiency has long served as the definite upper bound for the thermal efficiency at maximum output power, and has thus shaped the development of finite-time thermodynamics. In this paper, we repeal the ruling consensus according to which it has a genuine universal character that can be derived from linear irreversible thermodynamics. We demonstrate that the Curzon-Ahlborn efficiency should instead properly be associated with a particular case of nonlinear heat engines, and we derive a generalized expression for the efficiency at maximum power beyond the restrictive case of linear models.
△ Less
Submitted 10 August, 2017; v1 submitted 23 December, 2016;
originally announced December 2016.
-
Small-signal model for frequency analysis of thermoelectric systems
Authors:
Y. Apertet,
H. Ouerdane
Abstract:
We show how small-signal analysis, a standard method in electrical engineering, may be applied to thermoelectric device performance measurement by extending a dc model to the dynamical regime. We thus provide a physical ground to \textit{ad-hoc} models used to interpret impedance spectroscopy of thermoelectric elements from an electrical circuit equivalent for thermoelectric systems in the frequen…
▽ More
We show how small-signal analysis, a standard method in electrical engineering, may be applied to thermoelectric device performance measurement by extending a dc model to the dynamical regime. We thus provide a physical ground to \textit{ad-hoc} models used to interpret impedance spectroscopy of thermoelectric elements from an electrical circuit equivalent for thermoelectric systems in the frequency domain. We particularly stress the importance of the finite thermal impedance of the thermal contacts between the thermoelectric system and the thermal reservoirs in the derivation of such models. The expression for the characteristic angular frequency of the thermoelectric system we obtain is a generalization of the expressions derived in previous studies. In particular, it allows to envisage impedance spectroscopy measurements beyond the restrictive case of adiabatic boundary conditions often difficult to achieve experimentally, and hence \emph{in-situ} characterization of thermoelectric generators.
△ Less
Submitted 10 August, 2017; v1 submitted 3 November, 2016;
originally announced November 2016.
-
Closed-loop approach to thermodynamics
Authors:
C. Goupil,
H. Ouerdane,
E. Herbert,
G. Benenti,
Y. D'Angelo,
Ph. Lecoeur
Abstract:
We present the closed loop approach to linear nonequilibrium thermodynamics considering a generic heat engine dissipatively connected to two temperature baths. The system is usually quite generally characterized by two parameters: the output power $P$ and the conversion efficiency $η$, to which we add a third one, the working frequency $ω$. We establish that a detailed understanding of the effects…
▽ More
We present the closed loop approach to linear nonequilibrium thermodynamics considering a generic heat engine dissipatively connected to two temperature baths. The system is usually quite generally characterized by two parameters: the output power $P$ and the conversion efficiency $η$, to which we add a third one, the working frequency $ω$. We establish that a detailed understanding of the effects of the dissipative coupling on the energy conversion process, necessitates the knowledge of only two quantities: the system's feedback factor $β$ and its open-loop gain $A_{0}$, the product of which, $A_{0}β$, characterizes the interplay between the efficiency, the output power and the operating rate of the system. By placing thermodynamics analysis on a higher level of abstraction, the feedback loop approach provides a versatile and economical, hence a very efficient, tool for the study of \emph{any} conversion engine operation for which a feedback factor may be defined.
△ Less
Submitted 3 October, 2016; v1 submitted 10 June, 2016;
originally announced June 2016.
-
The thermoelectric working fluid: thermodynamics and transport
Authors:
G. Benenti,
H. Ouerdane,
C. Goupil
Abstract:
Thermoelectric devices are heat engines, which operate as generators or refrigerators using the conduction electrons as a working fluid. The thermoelectric heat-to-work conversion efficiency has always been typically quite low, but much effort continues to be devoted to the design of new materials boasting improved transport properties that would make them of the electron crystal-phonon glass type…
▽ More
Thermoelectric devices are heat engines, which operate as generators or refrigerators using the conduction electrons as a working fluid. The thermoelectric heat-to-work conversion efficiency has always been typically quite low, but much effort continues to be devoted to the design of new materials boasting improved transport properties that would make them of the electron crystal-phonon glass type of systems. On the other hand, there are comparatively few studies where a proper thermodynamic treatment of the electronic working fluid is proposed. The present article aims to contribute to bridge this gap by addressing both the thermodynamic and transport properties of the thermoelectric working fluid covering a variety of models, including interacting systems.
△ Less
Submitted 21 February, 2016;
originally announced February 2016.
-
A note on the electrochemical nature of the thermoelectric power
Authors:
Y. Apertet,
H. Ouerdane,
C. Goupil,
Ph. Lecoeur
Abstract:
While thermoelectric transport theory is well established and widely applied, there remains some degree of confusion on the proper thermodynamic definition of the Seebeck coefficient (or thermoelectric power) which is a measure of the strength of the mutual interaction between electric charge transport and heat transport. Indeed, as one considers a thermoelectric system, it is not always clear whe…
▽ More
While thermoelectric transport theory is well established and widely applied, there remains some degree of confusion on the proper thermodynamic definition of the Seebeck coefficient (or thermoelectric power) which is a measure of the strength of the mutual interaction between electric charge transport and heat transport. Indeed, as one considers a thermoelectric system, it is not always clear whether the Seebeck coefficient is to be related to the gradient of the system's chemical potential or to the gradient of its electrochemical potential. This pedagogical article aims to shed light on this confusion and clarify the thermodynamic definition of the thermoelectric coupling. First, we recall how the Seebeck coefficient is experimentally determined. We then turn to the analysis of the relationship between the thermoelectric power and the relevant potentials in the thermoelectric system: As the definitions of the chemical and electrochemical potentials are clarified, we show that, with a proper consideration of each potential, one may derive the Seebeck coefficient of a non-degenerate semiconductor without the need to introduce a contact potential as seen sometimes in the literature. Furthermore, we demonstrate that the phenomenological expression of the electrical current resulting from thermoelectric effects may be directly obtained from the drift-diffusion equation.
△ Less
Submitted 2 April, 2016; v1 submitted 19 February, 2015;
originally announced February 2015.
-
Green thermoelectrics: Observation and analysis of plant thermoelectric response
Authors:
C. Goupil,
H. Ouerdane,
A. Khamsing,
Y. Apertet,
F. Bouteau,
S. Mancuso,
R. Patino,
Ph. Lecoeur
Abstract:
Plants are sensitive to thermal and electrical effects; yet the coupling of both, known as thermoelectricity, and its quantitative measurement in vegetal systems never were reported. We recorded the thermoelectric response of bean sprouts under various thermal conditions and stress. The obtained experimental data unambiguously demonstrate that a temperature difference between the roots and the lea…
▽ More
Plants are sensitive to thermal and electrical effects; yet the coupling of both, known as thermoelectricity, and its quantitative measurement in vegetal systems never were reported. We recorded the thermoelectric response of bean sprouts under various thermal conditions and stress. The obtained experimental data unambiguously demonstrate that a temperature difference between the roots and the leaves of a bean sprout induces a thermoelectric voltage between these two points. Basing our analysis of the data on the force-flux formalism of linear response theory, we found that the strength of the vegetal equivalent to the thermoelectric coupling is one order of magnitude larger than that in the best thermoelectric materials. Experimental data also show the importance of the thermal stress variation rate in the plant's electrophysiological response. Therefore, thermoelectric effects are sufficiently important to partake in the complex and intertwined processes of energy and matter transport within plants.
△ Less
Submitted 12 February, 2015;
originally announced February 2015.
-
Enhanced thermoelectric coupling near electronic phase transition: the role of fluctuation Cooper pairs
Authors:
Henni Ouerdane,
Andrey A. Varlamov,
Alexey V. Kavokin,
Christophe Goupil,
Cronin B. Vining
Abstract:
Thermoelectric energy conversion is a direct but low-efficiency process, which precludes the development of long-awaited wide-scale applications. As a breakthrough permitting a drastic performance increase is seemingly out of reach, we fully reconsider the problem of thermoelectric coupling enhancement. The corner stone of our approach is the observation that heat engines are particularly efficien…
▽ More
Thermoelectric energy conversion is a direct but low-efficiency process, which precludes the development of long-awaited wide-scale applications. As a breakthrough permitting a drastic performance increase is seemingly out of reach, we fully reconsider the problem of thermoelectric coupling enhancement. The corner stone of our approach is the observation that heat engines are particularly efficient when their operation involves a phase transition of their working fluid. We derive and compute the thermoelastic coefficients of various systems, including Bose and Fermi gases, and fluctuation Cooper pairs. Combination of these coefficients yields the definition of the thermodynamic figure of merit, the divergence of which at $finite$ temperature indicates that conditions are fulfilled for the best possible use of the thermoelectric working fluid. Here, this situation occurs in the fluctuation regime only, as a consequence of the increased compressibility of the working fluid near its phase transition. Our results and analysis clearly show that efforts in the field of thermoelectricity can now be productively directed towards systems where electronic phase transitions are possible.
△ Less
Submitted 30 December, 2014;
originally announced December 2014.
-
Influence of thermal environment on optimal working conditions of thermoelectric generators
Authors:
Y. Apertet,
H. Ouerdane,
C. Goupil,
Ph. Lecoeur
Abstract:
Optimization analyses of thermoelectric generators operation is of importance both for practical applications and theoretical considerations. Depending on the desired goal, two different strategies are possible to achieve high performance: through optimization one may seek either power output maximization or conversion efficiency maximization. Recent literature reveals the persistent flawed notion…
▽ More
Optimization analyses of thermoelectric generators operation is of importance both for practical applications and theoretical considerations. Depending on the desired goal, two different strategies are possible to achieve high performance: through optimization one may seek either power output maximization or conversion efficiency maximization. Recent literature reveals the persistent flawed notion that these two optimal working conditions may be achieved simultaneously. In this article, we lift all source of confusion by correctly posing the problem and solving it. We assume and discuss two possibilities for the environment of the generator to govern its operation: constant incoming heat flux, and constant temperature difference between the heat reservoirs. We demonstrate that, while power and efficiency are maximized simultaneously if the first assumption is considered, this is not possible with the second assumption. This latter corresponds to the seminal analyses of Ioffe who put forth and stressed the importance of the thermoelectric figure of merit $ZT$. We also provide a simple procedure to determine the different optimal design parameters of a thermoelectric generator connected to heat reservoirs through thermal contacts with a finite and fixed thermal conductance.
△ Less
Submitted 8 October, 2014; v1 submitted 30 August, 2014;
originally announced September 2014.
-
Structural analysis of strained LaVO$_3$ thin films
Authors:
H. Rotella,
O. Copie,
G. Mouillard-Steciuk,
H. Ouerdane,
P. Boullay,
P. Roussel,
M. Morales,
A. David,
A. Pautrat,
B. Mercey,
L. Lutterotti,
D. Chateigner,
W. Prellier
Abstract:
While structure refinement is routinely achieved for simple bulk materials, the accurate structural determination still poses challenges for thin films due on the one hand to the small amount of material deposited on the thicker substrate and, on the other hand, to the intricate epitaxial relationships that substantially complicate standard X-ray diffraction analysis. Using a combined approach, we…
▽ More
While structure refinement is routinely achieved for simple bulk materials, the accurate structural determination still poses challenges for thin films due on the one hand to the small amount of material deposited on the thicker substrate and, on the other hand, to the intricate epitaxial relationships that substantially complicate standard X-ray diffraction analysis. Using a combined approach, we analyze the crystal structure of epitaxial LaVO$_3$ thin films grown on (100)-oriented SrTiO$_3$. Transmission electron microscopy study reveals that the thin films are epitaxially grown on SrTiO$_3$ and points to the presence of 90$^{\circ}$ oriented domains. The mapping of the reciprocal space obtained by high resolution X-ray diffraction permits refinement of the lattice parameters. We finally deduce that strain accommodation imposes a monoclinic structure onto the LaVO$_3$ film. The reciprocal space maps are numerically processed and the extracted data computed to refine the atomic positions, which are compared to those obtained using precession electron diffraction tomography. We discuss the obtained results and our methodological approach as a promising thin film structure determination for complex systems.
△ Less
Submitted 7 July, 2014; v1 submitted 28 March, 2014;
originally announced March 2014.
-
Revisiting Feynman's ratchet with thermoelectric transport theory
Authors:
Y. Apertet,
H. Ouerdane,
C. Goupil,
Ph. Lecoeur
Abstract:
We show how the formalism used for thermoelectric transport may be adapted to Smoluchowski's seminal thought experiment also known as Feynman's ratchet and pawl system. Our analysis rests on the notion of useful flux, which for a thermoelectric system is the electrical current and for Feynman's ratchet is the effective jump frequency. Our approach yields original insight into the derivation and an…
▽ More
We show how the formalism used for thermoelectric transport may be adapted to Smoluchowski's seminal thought experiment also known as Feynman's ratchet and pawl system. Our analysis rests on the notion of useful flux, which for a thermoelectric system is the electrical current and for Feynman's ratchet is the effective jump frequency. Our approach yields original insight into the derivation and analysis of the system's properties. In particular we define an entropy per tooth in analogy with the entropy per carrier or Seebeck coefficient, and we derive the analogue to Kelvin's second relation for Feynman's ratchet. Owing to the formal similarity between the heat fluxes balance equations for a thermoelectric generator (TEG) and those for Feynman's ratchet, we introduce a distribution parameter that quantifies the amount of heat that flows through the cold and hot sides of both heat engines. While it is well established that $γ$ = 1/2 for a TEG, it is equal to 1 for Feynman's ratchet. This implies that no heat may be rejected in the cold reservoir for the latter case. Further, the analysis of the efficiency at maximum power shows that the so-called Feynman efficiency corresponds to that of an exoreversible engine, with $γ$ = 1. Then, turning to the nonlinear regime, we generalize the approach based on the convection picture and introduce two different types of resistance to distinguish the dynamical behavior of the considered system from its ability to dissipate energy. We finally put forth the strong similarity between the original Feynman ratchet and a mesoscopic thermoelectric generator with a single conducting channel.
△ Less
Submitted 17 August, 2014; v1 submitted 28 March, 2014;
originally announced March 2014.
-
Comment on "Heat dissipation in atomic-scale junctions"
Authors:
Y. Apertet,
H. Ouerdane,
C. Goupil,
Ph. Lecoeur
Abstract:
We discuss the recent results of Lee et al. [Nature 498, 209 (2013)] using the notion of thermoelectric convection. In particular, we highlight the fact that this contribution to the thermal flux is not a dissipative process.
We discuss the recent results of Lee et al. [Nature 498, 209 (2013)] using the notion of thermoelectric convection. In particular, we highlight the fact that this contribution to the thermal flux is not a dissipative process.
△ Less
Submitted 22 January, 2014;
originally announced January 2014.
-
A linear nonequilibrium thermodynamics approach to optimization of thermoelectric devices
Authors:
H. Ouerdane,
C. Goupil,
Y. Apertet,
A. Michot,
A. Abbout
Abstract:
Improvement of thermoelectric systems in terms of performance and range of applications relies on progress in materials science and optimization of device operation. In this chapter, we focuse on optimization by taking into account the interaction of the system with its environment. For this purpose, we consider the illustrative case of a thermoelectric generator coupled to two temperature baths v…
▽ More
Improvement of thermoelectric systems in terms of performance and range of applications relies on progress in materials science and optimization of device operation. In this chapter, we focuse on optimization by taking into account the interaction of the system with its environment. For this purpose, we consider the illustrative case of a thermoelectric generator coupled to two temperature baths via heat exchangers characterized by a thermal resistance, and we analyze its working conditions. Our main message is that both electrical and thermal impedance matching conditions must be met for optimal device performance. Our analysis is fundamentally based on linear nonequilibrium thermodynamics using the force-flux formalism. An outlook on mesoscopic systems is also given.
△ Less
Submitted 30 August, 2013;
originally announced August 2013.
-
Comment on "Effective thermal conductivity in thermoelectric materials"
Authors:
Y. Apertet,
H. Ouerdane,
C. Goupil,
Ph. Lecoeur
Abstract:
In a recent article, Baranowski et al. [J. Appl. Phys. 113, 204904 (2013)] proposed a model that allegedly facilitates optimization of thermoelectric generators operation as these latter are in contact with hot and cold temperature baths through finite conductance heat exchangers. In this Comment, we argue that the results and analyses presented by these authors are misleading since their model is…
▽ More
In a recent article, Baranowski et al. [J. Appl. Phys. 113, 204904 (2013)] proposed a model that allegedly facilitates optimization of thermoelectric generators operation as these latter are in contact with hot and cold temperature baths through finite conductance heat exchangers. In this Comment, we argue that the results and analyses presented by these authors are misleading since their model is incomplete and rests on an inappropriate assumption derived from thermoelectric compatibility theory.
△ Less
Submitted 17 August, 2014; v1 submitted 11 July, 2013;
originally announced July 2013.
-
On the efficiency at maximum cooling power
Authors:
Yann Apertet,
Henni Ouerdane,
Aurelie Michot,
Christophe Goupil,
Philippe Lecoeur
Abstract:
The efficiency at maximum power (EMP) of heat engines operating as generators is one corner stone of finite-time thermodynamics, the Curzon-Ahlborn efficiency $η_{\rm CA}$ being considered as a universal upper bound. Yet, no valid counterpart to $η_{\rm CA}$ has been derived for the efficiency at maximum cooling power (EMCP) for heat engines operating as refrigerators. In this Letter we analyse th…
▽ More
The efficiency at maximum power (EMP) of heat engines operating as generators is one corner stone of finite-time thermodynamics, the Curzon-Ahlborn efficiency $η_{\rm CA}$ being considered as a universal upper bound. Yet, no valid counterpart to $η_{\rm CA}$ has been derived for the efficiency at maximum cooling power (EMCP) for heat engines operating as refrigerators. In this Letter we analyse the reasons of the failure to obtain such a bound and we demonstrate that, despite the introduction of several optimisation criteria, the maximum cooling power condition should be considered as the genuine equivalent of maximum power condition in the finite-time thermodynamics frame. We then propose and discuss an analytic expression for the EMCP in the specific case of exoreversible refrigerators.
△ Less
Submitted 3 September, 2013; v1 submitted 23 June, 2013;
originally announced June 2013.
-
From local force-flux relationships to internal dissipations and their impact on heat engine performance: The illustrative case of a thermoelectric generator
Authors:
Yann Apertet,
Henni Ouerdane,
Christophe Goupil,
Philippe Lecoeur
Abstract:
We present an in-depth analysis of the sometimes understated role of the principle of energy conservation in linear irreversible thermodynamics. Our case study is that of a thermoelectric generator (TEG), which is a heat engine of choice in irreversible thermodynamics, owing to the coupling between the electrical and heat fluxes. We show why Onsager's reciprocal relations must be considered locall…
▽ More
We present an in-depth analysis of the sometimes understated role of the principle of energy conservation in linear irreversible thermodynamics. Our case study is that of a thermoelectric generator (TEG), which is a heat engine of choice in irreversible thermodynamics, owing to the coupling between the electrical and heat fluxes. We show why Onsager's reciprocal relations must be considered locally and how internal dissipative processes emerge from the extension of these relations to a global scale: the linear behavior of a heat engine at the local scale is associated with a dissipation process that must partake in the global energy balance. We discuss the consequences of internal dissipations on the so-called efficiency at maximum power, in the light of our comparative analyses of exoreversibility and endoreversibility on the one hand, and of two classes of heat engines, autonomous and periodically-driven, on the other hand. Finally, basing our analysis on energy conservation, we also discuss recent works which claim the possibility to overcome the traditional boundaries on efficiency imposed by finite-time thermodynamics in thermoelectric systems with broken time-reversal symmetry; this we do by introducing a "thermal" thermopower and an "electrical" thermopower which permits an analysis of the thermoelectric response of the TEG considering a possible dissymmetry between the electrical/thermal and the thermal/electrical couplings.
△ Less
Submitted 30 August, 2013; v1 submitted 20 June, 2013;
originally announced June 2013.
-
Statistical analysis of the figure of merit of a two-level thermoelectric system: a random matrix approach
Authors:
Adel Abbout,
Henni Ouerdane,
Christophe Goupil
Abstract:
Using the tools of random matrix theory we develop a statistical analysis of the transport properties of thermoelectric low-dimensional systems made of two electron reservoirs set at different temperatures and chemical potentials, and connected through a low-density-of-states two-level quantum dot that acts as a conducting chaotic cavity. Our exact treatment of the chaotic behavior in such devices…
▽ More
Using the tools of random matrix theory we develop a statistical analysis of the transport properties of thermoelectric low-dimensional systems made of two electron reservoirs set at different temperatures and chemical potentials, and connected through a low-density-of-states two-level quantum dot that acts as a conducting chaotic cavity. Our exact treatment of the chaotic behavior in such devices lies on the scattering matrix formalism and yields analytical expressions for the joint probability distribution functions of the Seebeck coefficient and the transmission profile, as well as the marginal distributions, at arbitrary Fermi energy. The scattering matrices belong to circular ensembles which we sample to numerically compute the transmission function, the Seebeck coefficient, and their relationship. The exact transport coefficients probability distributions are found to be highly non-Gaussian for small numbers of conduction modes, and the analytical and numerical results are in excellent agreement. The system performance is also studied, and we find that the optimum performance is obtained for half-transparent quantum dots; further, this optimum may be enhanced for systems with few conduction modes.
△ Less
Submitted 7 July, 2016; v1 submitted 15 April, 2013;
originally announced April 2013.
-
Reply to the Comment on "Optimal working conditions for thermoelectric generators with realistic thermal coupling" by S. Su et al
Authors:
Y. Apertet,
H. Ouerdane,
O. Glavatskaya,
C. Goupil,
P. Lecoeur
Abstract:
We reply to the comment made by Su et al. on "Optimal working conditions for thermoelectric generators with realistic thermal coupling". In particular we justify the efficiency definition used in the main paper.
We reply to the comment made by Su et al. on "Optimal working conditions for thermoelectric generators with realistic thermal coupling". In particular we justify the efficiency definition used in the main paper.
△ Less
Submitted 3 April, 2013;
originally announced April 2013.
-
Mesoscopic thermoelectric transport near zero transmission energies
Authors:
Adel Abbout,
Henni Ouerdane,
Christophe Goupil
Abstract:
We study the thermoelectric transport coefficients of a one-dimensional (1D) electron waveguide connected to one and then two off-channel cavities, in the presence of dephasing phonons. The model system is that of a linear chain described as a 1D lattice. For simplicity we consider single-mode cavities, which may be tuned with external gates. While the presence of only one off-channel cavity yield…
▽ More
We study the thermoelectric transport coefficients of a one-dimensional (1D) electron waveguide connected to one and then two off-channel cavities, in the presence of dephasing phonons. The model system is that of a linear chain described as a 1D lattice. For simplicity we consider single-mode cavities, which may be tuned with external gates. While the presence of only one off-channel cavity yields a nearly symmetric transmission profile, which is canceled around the cavity mode, an additional cavity modifies this profile strongly and results in an asymmetric shape characterized by oscillations. In both cases, we consider electron-phonon interactions in our calculations and analyze their effects on the transmission function around the Fermi energy. Knowledge of the energy-dependent transmission function allows the numerical computation of thermoelectric transport coefficients, including the thermopower. In the presence of a second off-channel cavity, the sign of the thermopower depends on the relative position of this cavity energy level with respect to the Fermi energy: the thermopower is positive when low-energy electrons in the vicinity of the Fermi level are not transmitted, and becomes negative when the higher-energy electrons are not transmitted.
△ Less
Submitted 11 April, 2013; v1 submitted 21 November, 2012;
originally announced November 2012.
-
Equivalent parameters for series thermoelectrics
Authors:
Y. Apertet,
H. Ouerdane,
C. Goupil,
Ph. Lecoeur
Abstract:
We study the physical processes at work at the interface of two thermoelectric generators (TEGs) thermally and electrically connected in series. We show and explain how these processes impact on the system's performance: the derivation of the equivalent electrical series resistance yields a term whose physical meaning is thoroughly discussed. We demonstrate that this term must exist as a consequen…
▽ More
We study the physical processes at work at the interface of two thermoelectric generators (TEGs) thermally and electrically connected in series. We show and explain how these processes impact on the system's performance: the derivation of the equivalent electrical series resistance yields a term whose physical meaning is thoroughly discussed. We demonstrate that this term must exist as a consequence of thermal continuity at the interface, since it is related to the variation of the junction temperature between the two TEGs associated in series as the electrical current varies. We then derive an expression for the equivalent series figure of merit. Finally we highlight the strong thermal/electrical symmetry between the parallel and series configurations and we compare our derivation with recent published results for the parallel configuration.
△ Less
Submitted 24 January, 2015; v1 submitted 25 June, 2012;
originally announced June 2012.
-
Internal convection in thermoelectric generator models
Authors:
Y. Apertet,
H. Ouerdane,
C. Goupil,
Ph. Lecoeur
Abstract:
Coupling between heat and electrical currents is at the heart of thermoelectric processes. From a thermal viewpoint this may be seen as an additional thermal flux linked to the appearance of electrical current in a given thermoelectric system. Since this additional flux is associated to the global displacement of charge carriers in the system, it can be qualified as convective in opposition to the…
▽ More
Coupling between heat and electrical currents is at the heart of thermoelectric processes. From a thermal viewpoint this may be seen as an additional thermal flux linked to the appearance of electrical current in a given thermoelectric system. Since this additional flux is associated to the global displacement of charge carriers in the system, it can be qualified as convective in opposition to the conductive part associated with both phonons transport and heat transport by electrons under open circuit condition, as, e.g., in the Wiedemann-Franz relation. In this article we demonstrate that considering the convective part of the thermal flux allows both new insight into the thermoelectric energy conversion and the derivation of the maximum power condition for generators with realistic thermal coupling.
△ Less
Submitted 2 July, 2012; v1 submitted 3 April, 2012;
originally announced April 2012.
-
Efficiency at maximum power of thermally coupled heat engines
Authors:
Y. Apertet,
H. Ouerdane,
C. Goupil,
Ph. Lecoeur
Abstract:
We study the efficiency at maximum power of two coupled heat engines, using thermoelectric generators (TEGs) as engines. Assuming that the heat and electric charge fluxes in the TEGs are strongly coupled, we simulate numerically the dependence of the behavior of the global system on the electrical load resistance of each generator in order to obtain the working condition that permits maximization…
▽ More
We study the efficiency at maximum power of two coupled heat engines, using thermoelectric generators (TEGs) as engines. Assuming that the heat and electric charge fluxes in the TEGs are strongly coupled, we simulate numerically the dependence of the behavior of the global system on the electrical load resistance of each generator in order to obtain the working condition that permits maximization of the output power. It turns out that this condition is not unique. We derive a simple analytic expression giving the relation between the electrical load resistance of each generator permitting output power maximization. We then focuse on the efficiency at maximum power (EMP) of the whole system to demonstrate that the Curzon-Ahlborn efficiency may not always be recovered: the EMP varies with the specific working conditions of each generator but remains in the range predicted by irreversible thermodynamics theory. We finally discuss our results in light of non-ideal Carnot engine behavior.
△ Less
Submitted 1 March, 2012;
originally announced March 2012.
-
Irreversibilities and efficiency at maximum power of heat engines: illustrative case of a thermoelectric generator
Authors:
Y. Apertet,
H. Ouerdane,
C. Goupil,
Ph. Lecoeur
Abstract:
Thermoelectric generators are particularly suitable to investigate the irreversible processes which govern the coupled transport of matter and heat in solid-state systems. We study the efficiency at maximum power in the strong coupling regime, where the thermal flux is proportionnal to the electrical current inside the generator. We demonstrate that depending on the source of irreversibility we ob…
▽ More
Thermoelectric generators are particularly suitable to investigate the irreversible processes which govern the coupled transport of matter and heat in solid-state systems. We study the efficiency at maximum power in the strong coupling regime, where the thermal flux is proportionnal to the electrical current inside the generator. We demonstrate that depending on the source of irreversibility we obtain either the Curzon-Ahlborn efficiency for external dissipation or a universal efficiency at maximum power for internal dissipation. A continuous change between these two extremes is evidenced. Effects of dissymetry of thermal contact conductance are also investigated.
△ Less
Submitted 1 March, 2012; v1 submitted 4 November, 2011;
originally announced November 2011.
-
Thermoelectric internal current loops inside inhomogeneous systems
Authors:
Y. Apertet,
H. Ouerdane,
C. Goupil,
Ph. Lecoeur
Abstract:
Considering a system composed of two different thermoelectric modules electrically and thermally connected in parallel, we demonstrate that the inhomogeneities of the thermoelectric properties of the materials may cause the appearance of an electrical current, which develops inside the system. We show that this current increases the effective thermal conductance of the whole system. We also discus…
▽ More
Considering a system composed of two different thermoelectric modules electrically and thermally connected in parallel, we demonstrate that the inhomogeneities of the thermoelectric properties of the materials may cause the appearance of an electrical current, which develops inside the system. We show that this current increases the effective thermal conductance of the whole system. We also discuss the significance of a recent finding concerning a reported new electrothermal effect in inhomogeneous bipolar semiconductors, in light of our results.
△ Less
Submitted 5 January, 2012; v1 submitted 4 October, 2011;
originally announced October 2011.
-
Optimal working conditions for thermoelectric generators with realistic thermal coupling
Authors:
Y. Apertet,
H. Ouerdane,
O. Glavatskaya,
C. Goupil,
Ph. Lecoeur
Abstract:
We study how maximum output power can be obtained from a thermoelectric generator(TEG) with nonideal heat exchangers. We demonstrate with an analytic approach based on a force-flux formalism that the sole improvement of the intrinsic characteristics of thermoelectric modules including the enhancement of the figure of merit is of limited interest: the constraints imposed by the working conditions o…
▽ More
We study how maximum output power can be obtained from a thermoelectric generator(TEG) with nonideal heat exchangers. We demonstrate with an analytic approach based on a force-flux formalism that the sole improvement of the intrinsic characteristics of thermoelectric modules including the enhancement of the figure of merit is of limited interest: the constraints imposed by the working conditions of the TEG must be considered on the same footing. Introducing an effective thermal conductance we derive the conditions which permit maximization of both efficiency and power production of the TEG dissipatively coupled to heat reservoirs. Thermal impedance matching must be accounted for as well as electrical impedance matching in order to maximize the output power. Our calculations also show that the thermal impedance does not only depend on the thermal conductivity at zero electrical current: it also depends on the TEG figure of merit. Our analysis thus yields both electrical and thermal conditions permitting optimal use of a thermoelectric generator.
△ Less
Submitted 17 December, 2011; v1 submitted 31 August, 2011;
originally announced August 2011.
-
Analytic model of effective screened Coulomb interactions in a multilayer system
Authors:
Henni Ouerdane
Abstract:
The main objective of the present work is the development of an analytically tractable model of screened electron-electron and electron-exciton interactions in layered systems composed of two parallel semiconductor quantum wells separated by a dielectric layer. These systems are promising for superconductivity with excitons-polaritons, and spin manipulation. Polarization effects induced by the die…
▽ More
The main objective of the present work is the development of an analytically tractable model of screened electron-electron and electron-exciton interactions in layered systems composed of two parallel semiconductor quantum wells separated by a dielectric layer. These systems are promising for superconductivity with excitons-polaritons, and spin manipulation. Polarization effects induced by the dielectric mismatch in the nanostructure are taken into account using the image charge method. The obtained analytic expressions are used to calculate screened electron-electron and electron-exciton interactions; these are compared to results computed using other recently published models.
△ Less
Submitted 26 August, 2011; v1 submitted 30 July, 2011;
originally announced August 2011.
-
Coulomb singularities in scattering wave functions of spin-orbit-coupled states
Authors:
Patrick Bogdanski,
Henni Ouerdane
Abstract:
We report on our analysis of the Coulomb singularity problem in the frame of the coupled channel scattering theory including spin-orbit interaction. We assume that the coupling between the partial wave components involves orbital angular momenta such that $Δl = 0, \pm 2$. In these conditions, the two radial functions, components of a partial wave associated to two values of the angular momentum…
▽ More
We report on our analysis of the Coulomb singularity problem in the frame of the coupled channel scattering theory including spin-orbit interaction. We assume that the coupling between the partial wave components involves orbital angular momenta such that $Δl = 0, \pm 2$. In these conditions, the two radial functions, components of a partial wave associated to two values of the angular momentum $l$, satisfy a system of two second-order ordinary differential equations. We examine the difficulties arising in the analysis of the behavior of the regular solutions near the origin because of this coupling. First, we demonstrate that for a singularity of the first kind in the potential, one of the solutions is not amenable to a power series expansion. The use of the Lippmann-Schwinger equations confirms this fact: a logarithmic divergence arises at the second iteration. To overcome this difficulty, we introduce two auxilliary functions which, together with the two radial functions, satisfy a system of four first-order differential equations. The reduction of the order of the differential system enables us to use a matrix-based approach, which generalizes the standard Frobenius method. We illustrate our analysis with numerical calculations of coupled scattering wave functions in a solid-state system.
△ Less
Submitted 13 July, 2011;
originally announced July 2011.
-
Polariton-polariton scattering in microcavities: A microscopic theory
Authors:
M. M. Glazov,
H. Ouerdane,
L. Pilozzi,
G. Malpuech,
A. V. Kavokin,
A. D'Andrea
Abstract:
We apply the fermion commutation technique for composite bosons to polariton-polariton scattering in semiconductor planar microcavities. Derivations are presented in a simple and physically transparent fashion. A procedure of orthogonolization of the initial and final two-exciton state wavefunctions is used to calculate the effective scattering matrix elements and the scattering rates. We show h…
▽ More
We apply the fermion commutation technique for composite bosons to polariton-polariton scattering in semiconductor planar microcavities. Derivations are presented in a simple and physically transparent fashion. A procedure of orthogonolization of the initial and final two-exciton state wavefunctions is used to calculate the effective scattering matrix elements and the scattering rates. We show how the bosonic stimulation of the scattering appears in this full fermionic approach whose equivalence to the bosonization method is thus demonstrated in the regime of low exciton density. We find an additional contribution to polariton-polariton scattering due to the exciton oscillator strength saturation, which we analyze as well. We present a theory of the polariton-polariton scattering with opposite spin orientations and show that this scattering process takes place mainly via dark excitonic states. Analytical estimations of the effective scattering amplitudes are given.
△ Less
Submitted 3 October, 2009; v1 submitted 9 February, 2009;
originally announced February 2009.
-
Ultrafast pump-probe dynamics in ZnSe-based semiconductor quantum-wells
Authors:
Henni Ouerdane,
George Papageorgiou,
Ian Galbraith,
Ajoy K. Kar,
Brian S. Wherrett
Abstract:
Pump-probe experiments are used as a controllable way to investigate the properties of photoexcited semiconductors, in particular, the absorption saturation. We present an experiment-theory comparison for ZnSe quantum wells, investigating the energy renormalization and bleaching of the excitonic resonances. Experiments were performed with spin-selective excitation and above-bandgap pumping. The…
▽ More
Pump-probe experiments are used as a controllable way to investigate the properties of photoexcited semiconductors, in particular, the absorption saturation. We present an experiment-theory comparison for ZnSe quantum wells, investigating the energy renormalization and bleaching of the excitonic resonances. Experiments were performed with spin-selective excitation and above-bandgap pumping. The model, based on the semiconductor Bloch equations in the screened Hartree-Fock approximation, takes various scattering processes into account phenomenologically. Comparing numerical results with available experimental data, we explain the experimental results and find that the electron spin-flip occurs on a time scale of 30 ps.
△ Less
Submitted 19 July, 2008;
originally announced July 2008.
-
Barnes slave boson approach to the two-site single impurity Anderson model with non-local interaction
Authors:
Raymond Fresard,
Henni Ouerdane,
Thilo Kopp
Abstract:
The Barnes slave boson approach to the $U=\infty$ single impurity Anderson model extended by a non-local Coulomb interaction is revisited. We demonstrate first that the radial gauge representation facilitates the treatment of such a non-local interaction by performing the \emph{exact} evaluation of the path integrals representing the partition function, the impurity hole density and the impurity…
▽ More
The Barnes slave boson approach to the $U=\infty$ single impurity Anderson model extended by a non-local Coulomb interaction is revisited. We demonstrate first that the radial gauge representation facilitates the treatment of such a non-local interaction by performing the \emph{exact} evaluation of the path integrals representing the partition function, the impurity hole density and the impurity hole density autocorrelation function for a two-site cluster. The free energy is also obtained on the same footing. Next, the exact results are compared to their approximations at saddle-point level, and it is shown that the saddle point evaluation recovers the exact answer in the limit of strong non-local Coulomb interaction, while the agreement between both schemes remains satisfactory in a large parameter range.
△ Less
Submitted 30 April, 2008; v1 submitted 29 January, 2008;
originally announced January 2008.
-
Bose glass and superfuid phases of cavity polaritons
Authors:
G. Malpuech,
D. D. Solnyshkov,
H. Ouerdane,
M. M. Glazov,
I. Shelykh
Abstract:
We report the calculation of cavity exciton-polariton phase diagram which takes into account the presence of realistic structural disorder. Polaritons are modelled as weakly interacting two-dimensional bosons. We show that with increasing density polaritons first undergo a quasi-phase transition towards a Bose glass: the condensate is localized in at least one minimum of the disorder potential,…
▽ More
We report the calculation of cavity exciton-polariton phase diagram which takes into account the presence of realistic structural disorder. Polaritons are modelled as weakly interacting two-dimensional bosons. We show that with increasing density polaritons first undergo a quasi-phase transition towards a Bose glass: the condensate is localized in at least one minimum of the disorder potential, depending on the value of the chemical potential of the polariton system. A further increase of the density leads to a percolation process of the polariton fluid which gives rise to a Kosterlitz-Thouless phase transition towards superfluidity. The spatial representation of the condensate wavefunction as well as the spectrum of elementary excitations are obtained from the solution of the Gross-Pitaevskii equation for all the phases.
△ Less
Submitted 29 January, 2007;
originally announced January 2007.
-
Slave bosons in radial gauge: a bridge between path integral and hamiltonian language
Authors:
Raymond Fresard,
Henni Ouerdane,
Thilo Kopp
Abstract:
We establish a correspondence between the resummation of world lines and the diagonalization of the Hamiltonian for a strongly correlated electronic system. For this purpose, we analyze the functional integrals for the partition function and the correlation functions invoking a slave boson representation in the radial gauge. We show in the spinless case that the Green's function of the physical…
▽ More
We establish a correspondence between the resummation of world lines and the diagonalization of the Hamiltonian for a strongly correlated electronic system. For this purpose, we analyze the functional integrals for the partition function and the correlation functions invoking a slave boson representation in the radial gauge. We show in the spinless case that the Green's function of the physical electron and the projected Green's function of the pseudofermion coincide. Correlation and Green's functions in the spinful case involve a complex entanglement of the world lines which, however, can be obtained through a strikingly simple extension of the spinless scheme. As a toy model we investigate the two-site cluster of the single impurity Anderson model which yields analytical results. All expectation values and dynamical correlation functions are obtained from the exact calculation of the relevant functional integrals. The hole density, the hole auto-correlation function and the Green's function are computed, and a comparison between spinless and spin 1/2 systems provides insight into the role of the radial slave boson field. In particular, the exact expectation value of the radial slave boson field is finite in both cases, and it is not related to a Bose condensate.
△ Less
Submitted 5 October, 2007; v1 submitted 25 January, 2007;
originally announced January 2007.
-
Scattering states of coupled valence-band holes in point defect potential derived from variable phase theory
Authors:
P. Bogdanski,
H. Ouerdane
Abstract:
In this article we present a method to compute the scattering states of holes in spherical bands in the strong spin-orbit coupling regime. More precisely, we calculate scattering phase shifts and amplitudes of holes induced by defects in a semiconductor crystal. We follow a previous work done on this topic by Ralph [H. I. Ralph, Philips Res. Rept. 32 160 (1977)] to account for the p-wave nature…
▽ More
In this article we present a method to compute the scattering states of holes in spherical bands in the strong spin-orbit coupling regime. More precisely, we calculate scattering phase shifts and amplitudes of holes induced by defects in a semiconductor crystal. We follow a previous work done on this topic by Ralph [H. I. Ralph, Philips Res. Rept. 32 160 (1977)] to account for the p-wave nature and the coupling of valence band states. We extend Ralph's analysis to incorporate finite-range potentials in the scattering problem. We find that the variable phase method provides a very convenient framework for our purposes and show in detail how scattering amplitudes and phase shifts are obtained. The Green's matrix of the Schroedinger equation, the Lippmann-Schwinger equation and the Born approximation are also discussed. Examples are provided to illustrate our calculations with Yukawa type potentials.
△ Less
Submitted 31 October, 2006;
originally announced October 2006.
-
Photon emission induced by elastic exciton--carrier scattering in semiconductor quantum wells
Authors:
H. Ouerdane,
R. Varache,
M. E. Portnoi,
I. Galbraith
Abstract:
We present a study of the elastic exciton--electron ($X-e^-$) and exciton--hole ($X-h$) scattering processes in semiconductor quantum wells, including fermion exchange effects. The balance between the exciton and the free carrier populations within the electron-hole plasma is discussed in terms of ionization degree in the nondegenerate regime. Assuming a two-dimensional Coulomb potential statica…
▽ More
We present a study of the elastic exciton--electron ($X-e^-$) and exciton--hole ($X-h$) scattering processes in semiconductor quantum wells, including fermion exchange effects. The balance between the exciton and the free carrier populations within the electron-hole plasma is discussed in terms of ionization degree in the nondegenerate regime. Assuming a two-dimensional Coulomb potential statically screened by the free carrier gas, we apply the variable phase method to obtain the excitonic wavefunctions, which we use to calculate the 1$s$ exciton--free carrier matrix elements that describe the scattering of excitons into the light cone where they can radiatively recombine. The photon emission rates due to the carrier-assisted exciton recombination in semiconductor quantum-wells (QWs) at room temperature and in a low density regime are obtained from Fermi's golden rule, and studied for mid-gap and wide-gap materials. The quantitative comparison of the direct and exchange terms of the scattering matrix elements shows that fermion exchange is the dominant mechanism of the exciton--carrier scattering process. This is confirmed by our analysis of the rates of photon emission induced by electron-assisted and hole-assisted exciton recombinations.
△ Less
Submitted 7 August, 2008; v1 submitted 19 September, 2005;
originally announced September 2005.
