-
Effect of Sn on generalized stacking fault energy surfaces in zirconium and its hydrides
Authors:
P. Chakraborty,
I. Mouton,
B. Gault,
A. Tehranchi,
J. Neugebauer,
T. Hickel
Abstract:
Hydrogen embrittlement in Zr alloy fuel cladding is a primary safety concern for water based nuclear reactors. Here we investigated the stabilisation of planar defects within the forming hydrides by Sn, the primary alloying element of Zircaloy-4 used in the cladding. In order to explain formation of hydrides and planar defects observed in our experiments, we performed atomic-scale ab initio calcul…
▽ More
Hydrogen embrittlement in Zr alloy fuel cladding is a primary safety concern for water based nuclear reactors. Here we investigated the stabilisation of planar defects within the forming hydrides by Sn, the primary alloying element of Zircaloy-4 used in the cladding. In order to explain formation of hydrides and planar defects observed in our experiments, we performed atomic-scale ab initio calculations focusing on the solute interactions with generalized stacking faults in hcp $α$-Zr and fcc zirconium hydrides. Our calculations showed that an increase in Sn concentration leads to a stabilisation of stacking faults in both $α$-Zr and hydride phases. However, the solution enthalpy of Sn is lower in the $α$-Zr as compared to the other hydride phases indicative of two competing processes of Sn depletion/enrichment at the Zr hydride/matrix interface. This is corroborated by experimental findings, where Sn is repelled by hydrides and is mostly found trapped at interfaces and planar defects indicative of stacking faults inside the hydride phases. Our systematic investigation enables us to understand the presence and distribution of solutes in the hydride phases, which provides a deeper insight into the microstructural evolution of such alloy's properties during its service lifetime.
△ Less
Submitted 19 September, 2022;
originally announced September 2022.
-
Three-dimensional atomically-resolved analytical imaging with a field ion microscope
Authors:
Shyam Katnagallu,
Felipe Felipe F. Morgado,
Isabelle Mouton,
Baptiste Gault,
Leigh T. Stephenson
Abstract:
Atom probe tomography (APT) helps elucidate the link between the nanoscale chemical variations and physical properties, but it has limited structural resolution. Field ion microscopy (FIM), a predecessor technique to APT, is capable of attaining atomic resolution along certain sets of crystallographic planes albeit at the expense of elemental identification. We demonstrate how two commercially-ava…
▽ More
Atom probe tomography (APT) helps elucidate the link between the nanoscale chemical variations and physical properties, but it has limited structural resolution. Field ion microscopy (FIM), a predecessor technique to APT, is capable of attaining atomic resolution along certain sets of crystallographic planes albeit at the expense of elemental identification. We demonstrate how two commercially-available atom probe instruments, one with a straight flight path and one fitted with a reflectron-lens, can be used to acquire time-of-flight mass spectrometry data concomitant with a FIM experiment. We outline various experimental protocols making use of temporal and spatial correlations to best discriminate field evaporated signals from the large field ionised background signal, demonstrating an unsophisticated yet efficient data mining strategy to provide this discrimination. We discuss the remaining experimental challenges that need be addressed, notably concerned with accurate detection and identification of individual field evaporated ions contained within the high field ionised flux that contributes to a FIM image. Our hybrid experimental approach can, in principle, exhibit true atomic resolution with elemental discrimination capabilities, neither of which atom probe nor field ion microscopy can individually fully deliver - thereby making this new approach, here broadly termed analytical field ion microscope (aFIM), unique.
△ Less
Submitted 23 March, 2021; v1 submitted 19 March, 2021;
originally announced March 2021.
-
Hydride growth mechanism in Zircaloy-4: investigation of the partitioning of alloying elements
Authors:
Isabelle Mouton,
Yanhong Chang,
Poulami Chakraborty,
Siyang Wang,
Leigh T. Stephenson,
T. Ben Britton,
Baptiste Gault
Abstract:
The long-term safety of water-based nuclear reactors relies in part on the reliability of zirconium-based nuclear fuel. Yet the progressive ingress of hydrogen during service makes zirconium alloys subject to delayed hydride cracking. Here, we use a combination of electron back-scattered diffraction and atom probe tomography to investigate specific microstructural features from the as-received sam…
▽ More
The long-term safety of water-based nuclear reactors relies in part on the reliability of zirconium-based nuclear fuel. Yet the progressive ingress of hydrogen during service makes zirconium alloys subject to delayed hydride cracking. Here, we use a combination of electron back-scattered diffraction and atom probe tomography to investigate specific microstructural features from the as-received sample and in the blocky-alpha microstructure, before and after electrochemical charging with hydrogen or deuterium followed by a low temperature heat treatment at 400C for 5 hours followed by furnace cooling at a rate of 0. 5C per min. Specimens for atom probe were prepared at cryogenic temperature to avoid the formation of spurious hydrides. We report on the compositional evolution of grains and grain boundaries over the course of the sample's thermal history, as well as the ways the growth of the hydrides modifies locally the composition and the structure of the alloy. We observe a significant amount of deuterium left in the matrix, even after the slow cooling and growth of the hydrides. Stacking faults form ahead of the growth front and Sn segregates at the hydride-matrix interface and on these faults. We propose that this segregation may facilitate further growth of the hydride. Our systematic investigation enables us discuss how the solute distribution affects the evolution of the alloy's properties during its service lifetime.
△ Less
Submitted 17 September, 2020;
originally announced September 2020.
-
Imaging individual solute atoms at crystalline imperfections in metals
Authors:
Shyam Katnagallu,
Leigh T. Stephenson,
Isabelle Mouton,
Christoph Freysoldt,
Aparna P. A. Subramanyam,
Jan Jenke,
Alvin N. Ladines,
Steffen Neumeier,
Thomas Hammerschmidt,
Ralf Drautz,
Jörg Neugebauer,
François Vurpillot,
Dierk Raabe,
Baptiste Gault
Abstract:
Directly imaging all atoms constituting a material and, maybe more importantly, crystalline defects that dictate materials' properties, remains a formidable challenge. Here, we propose a new approach to chemistry-sensitive field-ion microscopy (FIM) combining contrast interpretation from density-functional theory (DFT) and elemental identification enabled by time-of-flight mass-spectrometry and da…
▽ More
Directly imaging all atoms constituting a material and, maybe more importantly, crystalline defects that dictate materials' properties, remains a formidable challenge. Here, we propose a new approach to chemistry-sensitive field-ion microscopy (FIM) combining contrast interpretation from density-functional theory (DFT) and elemental identification enabled by time-of-flight mass-spectrometry and data mining. Analytical-FIM has true atomic resolution and we demonstrate how the technique can reveal the presence of individual solute atoms at specific positions in the microstructure. The performance of this new technique is showcased in revealing individual Re atoms at crystalline defects formed in Ni during creep deformation. The atomistic details offered by A-FIM allowed us to directly compare our results with simulations, and to tackle a long-standing question of how Re extends lifetime of Ni-based superalloys in service at high-temperature.
△ Less
Submitted 31 March, 2019; v1 submitted 8 March, 2019;
originally announced March 2019.
-
Atomic-scale investigation of hydrogen distribution in a Ti-Mo alloy
Authors:
Fengkai Yan,
Isabelle Mouton,
Leigh T. Stephenson,
Andrew J. Breen,
Yanhong Chang,
Dirk Ponge,
Dierk Raabe,
Baptiste Gault
Abstract:
Ingress of hydrogen is often linked to catastrophic failure of Ti-alloys. Here, we quantify the hydrogen distribution in fully \b{eta} and α+\b{eta} Ti-Mo alloys by using atom probe tomography. Hydrogen does not segregate at grain boundaries in the fully \b{eta} sample but segregates at some α/\b{eta} phase boundaries with a composition exceeding 20 at.% in the α+\b{eta} sample. No stable hydrides…
▽ More
Ingress of hydrogen is often linked to catastrophic failure of Ti-alloys. Here, we quantify the hydrogen distribution in fully \b{eta} and α+\b{eta} Ti-Mo alloys by using atom probe tomography. Hydrogen does not segregate at grain boundaries in the fully \b{eta} sample but segregates at some α/\b{eta} phase boundaries with a composition exceeding 20 at.% in the α+\b{eta} sample. No stable hydrides were observed in either sample. The hydrogen concentration in \b{eta} phases linearly decreases from ~13 at. % to ~4 at. % with increasing Mo-content, which is ascribed to the suppression of hydrogen uptake by Mo addition.
△ Less
Submitted 3 December, 2018;
originally announced December 2018.
-
Electrical and Optical Properties of Heavily Ge-Doped AlGaN
Authors:
R. Blasco,
A. Ajay,
E. Robin,
C. Bougerol,
K. Lorentz,
L. C. Alves,
I. Mouton,
L. Amichi,
A. Grenier,
E. Monroy
Abstract:
We report the effect of germanium as n-type dopant on the electrical and optical properties of AlxGa1-xN layers grown by plasma assisted molecular-beam epitaxy. The Al content has been varied from x = 0 to 0.66, confirmed by Rutherford backscattering spectrometry, and the Ge concentration was increased up to [Ge] = 1E21 cm-3. Even at these high doping levels Ge does not induce any structural degra…
▽ More
We report the effect of germanium as n-type dopant on the electrical and optical properties of AlxGa1-xN layers grown by plasma assisted molecular-beam epitaxy. The Al content has been varied from x = 0 to 0.66, confirmed by Rutherford backscattering spectrometry, and the Ge concentration was increased up to [Ge] = 1E21 cm-3. Even at these high doping levels Ge does not induce any structural degradation in AlxGa1-xN layers with x below 0.15. However, for higher Al compositions, clustering of Ge forming crystallites were observed. Hall effect measurements show a gradual decrease of the carrier concentration when increasing the Al mole fraction, which is already noticeable in samples with x = 0.24. Samples with x = 0.64-0.66 remain conductive, but the donor activation rate drops to around 0.1% (carrier concentration around 1E18 cm-3 for [Ge] = 1E21 cm-3). From the optical point of view, the low temperature photoluminescence is dominated by the band-to-band emission, which show only spectral shift and broadening associated to the Burstein-Moss effect. The evolution of the photoluminescence peak position with temperature shows that the free carriers due to Ge doping can efficiently screen the potential fluctuations induced by alloy disorder.
△ Less
Submitted 13 December, 2018; v1 submitted 25 October, 2018;
originally announced October 2018.
-
Quantification challenges for atom probe tomography of hydrogen and deuterium in Zircaloy-4
Authors:
Isabelle Mouton,
Andrew J. Breen,
Siyang Wang,
Yanhong Chang,
Agnieszka Szczepaniak,
Paraskevas Kontis,
Leigh T. Stephenson,
Dierk Raabe,
M. Herbig,
T. Ben Britton,
Baptiste Gault
Abstract:
Analysis and understanding of the role of hydrogen in metals is a significant challenge for the future of materials science, and this is a clear objective of recent work in the atom probe tomography (APT) community. Isotopic marking by deuteration has often been proposed as the preferred route to enable quantification of hydrogen by APT. Zircaloy-4 was charged electrochemically with hydrogen and d…
▽ More
Analysis and understanding of the role of hydrogen in metals is a significant challenge for the future of materials science, and this is a clear objective of recent work in the atom probe tomography (APT) community. Isotopic marking by deuteration has often been proposed as the preferred route to enable quantification of hydrogen by APT. Zircaloy-4 was charged electrochemically with hydrogen and deuterium under the same conditions to form large hydrides and deuterides. Our results from a Zr hydride and a Zr deuteride highlight challenges associated to accurate quantification of hydrogen and deuterium, in particular associated to the overlap of peaks at low mass-to-charge ratio and of hydrogen/deuterium containing molecular ions. We discuss possible ways to ensure that appropriate information is extracted from APT analysis of hydrogen in a zirconium alloy systems that is important for nuclear power.
△ Less
Submitted 3 February, 2019; v1 submitted 10 September, 2018;
originally announced September 2018.
-
Atomic scale analysis of grain boundary deuteride growth front in Zircaloy-4
Authors:
A. J. Breen,
I. Mouton,
W. Lu,
S. Wang,
A. Szczepaniak,
P. Kontis,
L. T. Stephenson,
Y. Chang,
A. K. da Silva,
C. Liebscher,
D. Raabe,
T. B. Britton,
M. Herbig,
B. Gault
Abstract:
Zircaloy-4 (Zr-1.5%Sn-0.2%Fe-0.1%Cr wt. %) was electrochemically charged with deuterium to create deuterides and subsequently analysed with atom probe tomography and scanning transmission electron microscopy to understand zirconium hydride formation and embrittlement. At the interface between the hexagonal close packed (HCP) α-Zr matrix and a face centred cubic (FCC) δdeuteride (ZrD1.5-1.65), a HC…
▽ More
Zircaloy-4 (Zr-1.5%Sn-0.2%Fe-0.1%Cr wt. %) was electrochemically charged with deuterium to create deuterides and subsequently analysed with atom probe tomography and scanning transmission electron microscopy to understand zirconium hydride formation and embrittlement. At the interface between the hexagonal close packed (HCP) α-Zr matrix and a face centred cubic (FCC) δdeuteride (ZrD1.5-1.65), a HCP ζphase deuteride (ZrD0.25-0.5) has been observed. Furthermore, Sn is rejected from the deuterides and segregates to the deuteride/α-Zr reaction front.
△ Less
Submitted 28 June, 2018; v1 submitted 26 June, 2018;
originally announced June 2018.
-
The Laplace project: an integrated suite for correlative atom probe tomography and electron microscopy under cryogenic and UHV conditions
Authors:
Leigh T. Stephenson,
Agnieszka Szczepaniak,
Isabelle Mouton,
Kristiane Ann Kathrin Rusitzka,
Andrew J. Breen,
Uwe Tezins,
Andreas Sturm,
Dirk Vogel,
Yanhong Chang,
Paraskevas Kontis,
Alexander Rosenthal,
Jeffrey D. Shepard,
Urs Maier,
Thomas F. Kelly,
Dierk Raabe,
Baptiste Gault
Abstract:
We present sample transfer instrumentation and integrated protocols for the preparation and correlative characterization of environmentally-sensitive materials by both atom probe tomography and electron microscopy. Ultra-high vacuum cryogenic suitcases allow specimen transfer between preparation, processing and several imaging platforms without exposure to atmospheric contamination. For expedient…
▽ More
We present sample transfer instrumentation and integrated protocols for the preparation and correlative characterization of environmentally-sensitive materials by both atom probe tomography and electron microscopy. Ultra-high vacuum cryogenic suitcases allow specimen transfer between preparation, processing and several imaging platforms without exposure to atmospheric contamination. For expedient transfers, we installed a fast-docking station equipped with a cryogenic pump upon three systems; two atom probes, a scanning electron microscope / Xe-plasma focused ion beam and a N$_2$-atmosphere glovebox. We also installed a plasma FIB with a solid-state cooling stage to reduce beam damage and contamination, through reducing chemical activity and with the cryogenic components as passive cryogenic traps. We demonstrate the efficacy of the new laboratory protocols by the successful preparation and transfer of two highly contamination- and temperature-sensitive samples - water and ice. Analysing pure magnesium atom probe data, we show that surface oxidation can be effectively suppressed using an entirely cryogenic protocol (during specimen preparation and during transfer). Starting with the cryogenically-cooled plasma FIB, we also prepared and transferred frozen ice samples while avoiding significant melting or sublimation, suggesting that we may be able to measure the nanostructure of other normally-liquid or soft materials. Isolated cryogenic protocols within the N$_2$ glove box demonstrate the absence of ice condensation suggesting that environmental control can commence from fabrication until atom probe analysis.
△ Less
Submitted 28 May, 2018;
originally announced May 2018.
-
Ge doping of GaN beyond the Mott transition
Authors:
A. Ajay,
J. Schörmann,
M. Jimenez-Rodriguez,
C. B. Lim,
F. Walther,
M. Rohnke,
I. Mouton,
L. Amichi,
C. Bougerol,
M. I. Den Hertog,
M. Eickhoff,
E. Monroy
Abstract:
We present a study of germanium as n-type dopant in wurtzite GaN films grown by plasma-assisted molecular beam epitaxy, reaching carrier concentrations of up to 6.7E20 cm-3 at 300K, well beyond the Mott density. The Ge concentration and free carrier density were found to scale linearly with the Ge flux in the studied range. All the GaN:Ge layers present smooth surface morphology with atomic terrac…
▽ More
We present a study of germanium as n-type dopant in wurtzite GaN films grown by plasma-assisted molecular beam epitaxy, reaching carrier concentrations of up to 6.7E20 cm-3 at 300K, well beyond the Mott density. The Ge concentration and free carrier density were found to scale linearly with the Ge flux in the studied range. All the GaN:Ge layers present smooth surface morphology with atomic terraces, without trace of pits or cracks, and the mosaicity of the samples has no noticeable dependence on the Ge concentration. The variation of the GaN:Ge band gap with the carrier concentration is consistent with theoretical calculations of the band gap renormalization due to electron-electron and electron-ion interaction, and Burstein-Moss effect.
△ Less
Submitted 8 July, 2016; v1 submitted 1 April, 2016;
originally announced April 2016.
