-
Kinetic Inductance and nonlinearity of MgB2 Films at 4K
Authors:
J. Greenfield,
C. Bell,
F. Faramarzi,
C. Kim,
R. Basu Thakur,
A. Wandui,
C. Frez,
P. Mauskopf,
D. Cunnane
Abstract:
We report on the fabrication and characterization of superconducting magnesium diboride (MgB$_2$) thin films intended for quantum-limited devices based non-linear kinetic inductance (NLKI) such as parametric amplifiers with either elevated operating temperatures or expanded frequency ranges. In order to characterize the MgB$_2$ material properties, we have fabricated coplanar waveguide (CPW) trans…
▽ More
We report on the fabrication and characterization of superconducting magnesium diboride (MgB$_2$) thin films intended for quantum-limited devices based non-linear kinetic inductance (NLKI) such as parametric amplifiers with either elevated operating temperatures or expanded frequency ranges. In order to characterize the MgB$_2$ material properties, we have fabricated coplanar waveguide (CPW) transmission lines and microwave resonators using $\approx$ 40 nm thick MgB$_2$ films with a measured kinetic inductance of $\sim$ 5.5 pH/$\square$ and internal quality factors, $Q_i \approx 3 \times 10^4$ at 4.2 K. We measure the NLKI in MgB$_2$ by applying a DC bias to a 6 cm long by 4 $μ$m wide CPW transmission line, and measuring the resulting phase delay caused by the current dependent NLKI. We also measure the current dependent NLKI through CPW resonators that shift down in frequency with increased power applied through the CPW feedline. Using these measurements, we calculate the characteristic non-linear current parameter, $I_*$, for multiple CPW geometries. We find values for corresponding current density, $J_* = 12-22$~MA/cm$^2$ and a ratio of the critical current to the non-linear current parameter, $I_C/I_* = 0.14-0.26$, similar to or higher than values for other superconductors such as NbTiN and TiN.
△ Less
Submitted 29 October, 2024;
originally announced October 2024.
-
Search for axion-like dark matter using solid-state nuclear magnetic resonance
Authors:
Deniz Aybas,
Janos Adam,
Emmy Blumenthal,
Alexander V. Gramolin,
Dorian Johnson,
Annalies Kleyheeg,
Samer Afach,
John W. Blanchard,
Gary P. Centers,
Antoine Garcon,
Martin Engler,
Nataniel L. Figueroa,
Marina Gil Sendra,
Arne Wickenbrock,
Matthew Lawson,
Tao Wang,
Teng Wu,
Haosu Luo,
Hamdi Mani,
Philip Mauskopf,
Peter W. Graham,
Surjeet Rajendran,
Derek F. Jackson Kimball,
Dmitry Budker,
Alexander O. Sushkov
Abstract:
We report the results of an experimental search for ultralight axion-like dark matter in the mass range 162 neV to 166 neV. The detection scheme of our Cosmic Axion Spin Precession Experiment (CASPEr) is based on a precision measurement of $^{207}$Pb solid-state nuclear magnetic resonance in a polarized ferroelectric crystal. Axion-like dark matter can exert an oscillating torque on $^{207}$Pb nuc…
▽ More
We report the results of an experimental search for ultralight axion-like dark matter in the mass range 162 neV to 166 neV. The detection scheme of our Cosmic Axion Spin Precession Experiment (CASPEr) is based on a precision measurement of $^{207}$Pb solid-state nuclear magnetic resonance in a polarized ferroelectric crystal. Axion-like dark matter can exert an oscillating torque on $^{207}$Pb nuclear spins via the electric-dipole moment coupling $g_d$, or via the gradient coupling $g_{\text{aNN}}$. We calibrated the detector and characterized the excitation spectrum and relaxation parameters of the nuclear spin ensemble with pulsed magnetic resonance measurements in a 4.4 T magnetic field. We swept the magnetic field near this value and searched for axion-like dark matter with Compton frequency within a 1 MHz band centered at 39.65 MHz. Our measurements place the upper bounds $|g_d|<9.5\times10^{-4}\,\text{GeV}^{-2}$ and $|g_{\text{aNN}}|<2.8\times10^{-1}\,\text{GeV}^{-1}$ (95% confidence level) in this frequency range. The constraint on $g_d$ corresponds to an upper bound of $1.0\times 10^{-21}\,\text{e}\cdot\text{cm}$ on the amplitude of oscillations of the neutron electric dipole moment, and $4.3\times 10^{-6}$ on the amplitude of oscillations of CP-violating $θ$ parameter of quantum chromodynamics. Our results demonstrate the feasibility of using solid-state nuclear magnetic resonance to search for axion-like dark matter in the nano-electronvolt mass range.
△ Less
Submitted 12 March, 2021; v1 submitted 4 January, 2021;
originally announced January 2021.
-
Initial Design of a W-band Superconducting Kinetic Inductance Qubit (Kineticon)
Authors:
Farzad B. Faramarzi,
Peter K. Day,
Jacob Glasby,
Sasha Sypkens,
Marco Colangelo,
Ralph Chamberlin,
Mohammad Mirhosseini,
Kevin Schmidt,
Karl K. Berggren Philip Mauskopf
Abstract:
Superconducting qubits are widely used in quantum computing research and industry. We describe a superconducting kinetic inductance qubit (and introduce the term Kineticon to describe it) operating at W-band frequencies with a nonlinear nanowire section that provides the anharmonicity required for two distinct quantum energy states. Operating the qubits at higher frequencies may relax the dilution…
▽ More
Superconducting qubits are widely used in quantum computing research and industry. We describe a superconducting kinetic inductance qubit (and introduce the term Kineticon to describe it) operating at W-band frequencies with a nonlinear nanowire section that provides the anharmonicity required for two distinct quantum energy states. Operating the qubits at higher frequencies may relax the dilution refrigerator temperature requirements for these devices and paves the path for multiplexing a large number of qubits. Millimeter-wave operation requires superconductors with relatively high $T_c$, which implies high gap frequency, 2$Δ/h$, beyond which photons break Cooper pairs. For example, NbTiN with $T_c =15\,\text{K}$ has a gap frequency near 1.4 THz, which is much higher than that of aluminum (90 GHz), allowing for operation throughout the millimeter-wave band. Here we describe a design and simulation of a W-band Kineticon qubit embedded in a 3-D cavity. We perform classical electromagnetic calculations of the resulting field distributions.
△ Less
Submitted 14 March, 2021; v1 submitted 15 December, 2020;
originally announced December 2020.
-
Kinetic Inductance Detectors and readout electronics for the OLIMPO experiment
Authors:
A. Paiella,
E. S. Battistelli,
M. G. Castellano,
I. Colantoni,
F. Columbro,
A. Coppolecchia,
G. D'Alessandro,
P. de Bernardis,
S. Gordon,
L. Lamagna,
H. Mani,
S. Masi,
P. Mauskopf,
G. Pettinari,
F. Piacentini,
G. Presta
Abstract:
Kinetic Inductance Detectors (KIDs) are superconductive low$-$temperature detectors useful for astrophysics and particle physics. We have developed arrays of lumped elements KIDs (LEKIDs) sensitive to microwave photons, optimized for the four horn-coupled focal planes of the OLIMPO balloon-borne telescope, working in the spectral bands centered at 150 GHz, 250 GHz, 350 GHz, and 460 GHz. This is ai…
▽ More
Kinetic Inductance Detectors (KIDs) are superconductive low$-$temperature detectors useful for astrophysics and particle physics. We have developed arrays of lumped elements KIDs (LEKIDs) sensitive to microwave photons, optimized for the four horn-coupled focal planes of the OLIMPO balloon-borne telescope, working in the spectral bands centered at 150 GHz, 250 GHz, 350 GHz, and 460 GHz. This is aimed at measuring the spectrum of the Sunyaev-Zel'dovich effect for a number of galaxy clusters, and will validate LEKIDs technology in a space-like environment. Our detectors are optimized for an intermediate background level, due to the presence of residual atmosphere and room--temperature optical system and they operate at a temperature of 0.3 K. The LEKID planar superconducting circuits are designed to resonate between 100 and 600 MHz, and to match the impedance of the feeding waveguides; the measured quality factors of the resonators are in the $10^{4}-10^{5}$ range, and they have been tuned to obtain the needed dynamic range. The readout electronics is composed of a $cold$ $part$, which includes a low noise amplifier, a dc$-$block, coaxial cables, and power attenuators; and a $room-temperature$ $part$, FPGA$-$based, including up and down-conversion microwave components (IQ modulator, IQ demodulator, amplifiers, bias tees, attenuators). In this contribution, we describe the optimization, fabrication, characterization and validation of the OLIMPO detector system.
△ Less
Submitted 3 April, 2019;
originally announced April 2019.
-
High quality factor manganese-doped aluminum lumped-element kinetic inductance detectors sensitive to frequencies below 100 GHz
Authors:
G. Jones,
B. R. Johnson,
M. H. Abitbol,
P. A. R. Ade,
S. Bryan,
H. -M. Cho,
P. Day,
D. Flanigan,
K. D. Irwin,
D. Li,
P. Mauskopf,
H. McCarrick,
A. Miller,
Y. R. Song,
C. Tucker
Abstract:
Aluminum lumped-element kinetic inductance detectors (LEKIDs) sensitive to millimeter-wave photons have been shown to exhibit high quality factors, making them highly sensitive and multiplexable. The superconducting gap of aluminum limits aluminum LEKIDs to photon frequencies above 100 GHz. Manganese-doped aluminum (Al-Mn) has a tunable critical temperature and could therefore be an attractive mat…
▽ More
Aluminum lumped-element kinetic inductance detectors (LEKIDs) sensitive to millimeter-wave photons have been shown to exhibit high quality factors, making them highly sensitive and multiplexable. The superconducting gap of aluminum limits aluminum LEKIDs to photon frequencies above 100 GHz. Manganese-doped aluminum (Al-Mn) has a tunable critical temperature and could therefore be an attractive material for LEKIDs sensitive to frequencies below 100 GHz if the internal quality factor remains sufficiently high when manganese is added to the film. To investigate, we measured some of the key properties of Al-Mn LEKIDs. A prototype eight-element LEKID array was fabricated using a 40 nm thick film of Al-Mn deposited on a 500 μm thick high-resistivity, float-zone silicon substrate. The manganese content was 900 ppm, the measured $T_c = 694\pm1$ mK, and the resonance frequencies were near 150 MHz. Using measurements of the forward scattering parameter $S_{21}$ at various bath temperatures between 65 and 250 mK, we determined that the Al-Mn LEKIDs we fabricated have internal quality factors greater than $2 \times 10^5$, which is high enough for millimeter-wave astrophysical observations. In the dark conditions under which these devices were measured, the fractional frequency noise spectrum shows a shallow slope that depends on bath temperature and probe tone amplitude, which could be two-level system noise. The anticipated white photon noise should dominate this level of low-frequency noise when the detectors are illuminated with millimeter-waves in future measurements. The LEKIDs responded to light pulses from a 1550 nm light-emitting diode, and we used these light pulses to determine that the quasiparticle lifetime is 60 μs.
△ Less
Submitted 15 April, 2017; v1 submitted 29 January, 2017;
originally announced January 2017.
-
Magnetic field dependence of the internal quality factor and noise performance of lumped-element kinetic inductance detectors
Authors:
Daniel Flanigan,
Bradley R. Johnson,
Maximilian H. Abitbol,
Sean Bryan,
Robin Cantor,
Peter K. Day,
Glenn Jones,
Philip Mauskopf,
Heather McCarrick,
Amber Miller,
Jonas Zmuidzinas
Abstract:
We present a technique for increasing the internal quality factor of kinetic inductance detectors (KIDs) by nulling ambient magnetic fields with a properly applied magnetic field. The KIDs used in this study are made from thin-film aluminum, they are mounted inside a light-tight package made from bulk aluminum, and they are operated near $150 \, \mathrm{mK}$. Since the thin-film aluminum has a sli…
▽ More
We present a technique for increasing the internal quality factor of kinetic inductance detectors (KIDs) by nulling ambient magnetic fields with a properly applied magnetic field. The KIDs used in this study are made from thin-film aluminum, they are mounted inside a light-tight package made from bulk aluminum, and they are operated near $150 \, \mathrm{mK}$. Since the thin-film aluminum has a slightly elevated critical temperature ($T_\mathrm{c} = 1.4 \, \mathrm{K}$), it therefore transitions before the package ($T_\mathrm{c} = 1.2 \, \mathrm{K}$), which also serves as a magnetic shield. On cooldown, ambient magnetic fields as small as approximately $30 \, \mathrm{μT}$ can produce vortices in the thin-film aluminum as it transitions because the bulk aluminum package has not yet transitioned and therefore is not yet shielding. These vortices become trapped inside the aluminum package below $1.2 \, \mathrm{K}$ and ultimately produce low internal quality factors in the thin-film superconducting resonators. We show that by controlling the strength of the magnetic field present when the thin film transitions, we can control the internal quality factor of the resonators. We also compare the noise performance with and without vortices present, and find no evidence for excess noise beyond the increase in amplifier noise, which is expected with increasing loss.
△ Less
Submitted 20 September, 2016;
originally announced September 2016.
-
Photon noise from chaotic and coherent millimeter-wave sources measured with horn-coupled, aluminum lumped-element kinetic inductance detectors
Authors:
Daniel Flanigan,
Heather McCarrick,
Glenn Jones,
Bradley R. Johnson,
Maximilian H. Abitbol,
Peter Ade,
Derek Araujo,
Kristi Bradford,
Robin Cantor,
George Che,
Peter K. Day,
Simon Doyle,
Carl Bjorn Kjellstrand,
Henry G LeDuc,
Michele Limon,
Vy Luu,
Philip Mauskopf,
Amber Miller,
Tony Mroczkowski,
Carole Tucker,
Jonas Zmuidzinas
Abstract:
We report photon-noise limited performance of horn-coupled, aluminum lumped-element kinetic inductance detectors at millimeter wavelengths. The detectors are illuminated by a millimeter-wave source that uses an active multiplier chain to produce radiation between 140 and 160 GHz. We feed the multiplier with either amplified broadband noise or a continuous-wave tone from a microwave signal generato…
▽ More
We report photon-noise limited performance of horn-coupled, aluminum lumped-element kinetic inductance detectors at millimeter wavelengths. The detectors are illuminated by a millimeter-wave source that uses an active multiplier chain to produce radiation between 140 and 160 GHz. We feed the multiplier with either amplified broadband noise or a continuous-wave tone from a microwave signal generator. We demonstrate that the detector response over a 40 dB range of source power is well-described by a simple model that considers the number of quasiparticles. The detector noise-equivalent power (NEP) is dominated by photon noise when the absorbed power is greater than approximately 1 pW, which corresponds to $\mathrm{NEP} \approx 2 \times 10^{-17} \, \mathrm{W} \, \mathrm{Hz}^{-1/2}$, referenced to absorbed power. At higher source power levels we observe the relationships between noise and power expected from the photon statistics of the source signal: $\mathrm{NEP} \propto P$ for broadband (chaotic) illumination and $\mathrm{NEP} \propto P^{1/2}$ for continuous-wave (coherent) illumination.
△ Less
Submitted 24 May, 2017; v1 submitted 22 October, 2015;
originally announced October 2015.
-
A Strained Silicon Cold Electron Bolometer using Schottky Contacts
Authors:
T. L. R. Brien,
P. A. R. Ade,
P. S. Barry,
C. Dunscombe,
D. R. Leadley,
D. V. Morozov,
M. Myronov,
E. H. C. Parker,
M. Prunnila,
M. J. Prest,
R. V. Sudiwala,
T. E. Whall,
P. D. Mauskopf
Abstract:
We describe optical characterisation of a Strained Silicon Cold Electron Bolometer (CEB), operating on a $350~\mathrm{mK}$ stage, designed for absorption of millimetre-wave radiation. The silicon Cold Electron Bolometer utilises Schottky contacts between a superconductor and an n++ doped silicon island to detect changes in the temperature of the charge carriers in the silicon, due to variations in…
▽ More
We describe optical characterisation of a Strained Silicon Cold Electron Bolometer (CEB), operating on a $350~\mathrm{mK}$ stage, designed for absorption of millimetre-wave radiation. The silicon Cold Electron Bolometer utilises Schottky contacts between a superconductor and an n++ doped silicon island to detect changes in the temperature of the charge carriers in the silicon, due to variations in absorbed radiation. By using strained silicon as the absorber, we decrease the electron-phonon coupling in the device and increase the responsivity to incoming power. The strained silicon absorber is coupled to a planar aluminium twin-slot antenna designed to couple to $160~\mathrm{GHz}$ and that serves as the superconducting contacts. From the measured optical responsivity and spectral response, we calculate a maximum optical efficiency of $50~\%$ for radiation coupled into the device by the planar antenna and an overall noise equivalent power (NEP), referred to absorbed optical power, of $1.1 \times 10^{-16}~\mathrm{\mbox{W Hz}^{-1/2}}$ when the detector is observing a $300~\mathrm{K}$ source through a $4~\mathrm{K}$ throughput limiting aperture. Even though this optical system is not optimised we measure a system noise equivalent temperature difference (NETD) of $6~\mathrm{\mbox{mK Hz}^{-1/2}}$. We measure the noise of the device using a cross-correlation of time stream data measured simultaneously with two junction field-effect transistor (JFET) amplifiers, with a base correlated noise level of $300~\mathrm{\mbox{pV Hz}^{-1/2}}$ and find that the total noise is consistent with a combination of photon noise, current shot noise and electron-phonon thermal noise.
△ Less
Submitted 31 July, 2014; v1 submitted 8 July, 2014;
originally announced July 2014.
-
Photon-noise limited sensitivity in titanium nitride kinetic inductance detectors
Authors:
Johannes Hubmayr,
Jim Beall,
Dan Becker,
Hsaio-Mei Cho,
Mark Devlin,
Bradley Dober,
Chris Groppi,
Gene C. Hilton,
Kent D. Irwin,
Dale Li,
Phillip Mauskopf,
Dave P. Pappas,
Jeff Van Lanen,
Michael R. Vissers,
Yiwen Wang,
Lian-Fu Wei,
Jiansong Gao
Abstract:
We demonstrate photon-noise limited performance at sub-millimeter wavelengths in feedhorn-coupled, microwave kinetic inductance detectors (MKIDs) made of a TiN/Ti/TiN trilayer superconducting film, tuned to have a transition temperature of 1.4~K. Micro-machining of the silicon-on-insulator wafer backside creates a quarter-wavelength backshort optimized for efficient coupling at 250~\micron. Using…
▽ More
We demonstrate photon-noise limited performance at sub-millimeter wavelengths in feedhorn-coupled, microwave kinetic inductance detectors (MKIDs) made of a TiN/Ti/TiN trilayer superconducting film, tuned to have a transition temperature of 1.4~K. Micro-machining of the silicon-on-insulator wafer backside creates a quarter-wavelength backshort optimized for efficient coupling at 250~\micron. Using frequency read out and when viewing a variable temperature blackbody source, we measure device noise consistent with photon noise when the incident optical power is $>$~0.5~pW, corresponding to noise equivalent powers $>$~3$\times 10^{-17}$ W/$\sqrt{\mathrm{Hz}}$. This sensitivity makes these devices suitable for broadband photometric applications at these wavelengths.
△ Less
Submitted 23 March, 2015; v1 submitted 16 June, 2014;
originally announced June 2014.
-
The electron-phonon relaxation time in thin superconducting titanium nitride films
Authors:
A. Kardakova,
M. Finkel,
D. Morozov,
V. Kovalyuk,
P. An,
C. Dunscombe,
M. Tarkhov,
P. Mauskopf,
T. M. Klapwijk,
G. Goltsman
Abstract:
We report on the direct measurement of the electron-phonon relaxation time, τeph, in disordered TiN films. Measured values of τeph are from 5.5 ns to 88 ns in the 4.2 to 1.7 K temperature range and consistent with a T-3 temperature dependence. The electronic density of states at the Fermi level N0 is estimated from measured material parameters. The presented results confirm that thin TiN films are…
▽ More
We report on the direct measurement of the electron-phonon relaxation time, τeph, in disordered TiN films. Measured values of τeph are from 5.5 ns to 88 ns in the 4.2 to 1.7 K temperature range and consistent with a T-3 temperature dependence. The electronic density of states at the Fermi level N0 is estimated from measured material parameters. The presented results confirm that thin TiN films are promising candidate-materials for ultrasensitive superconducting detectors.
△ Less
Submitted 20 December, 2013;
originally announced December 2013.
