-
Modification of the trapped field in bulk high-temperature superconductors as a result of the drilling of a pattern of artificial columnar holes
Authors:
Gregory P. Lousberg,
J. -F. Fagnard,
M. Ausloos,
Ph. Vanderbemden,
B. Vanderheyden
Abstract:
The trapped magnetic field is examined in bulk high-temperature superconductors that are artificially drilled along their c-axis. The influence of the hole pattern on the magnetization is studied and compared by means of numerical models and Hall probe mapping techniques. To this aim, we consider two bulk YBCO samples with a rectangular cross-section that are drilled each by six holes arranged eit…
▽ More
The trapped magnetic field is examined in bulk high-temperature superconductors that are artificially drilled along their c-axis. The influence of the hole pattern on the magnetization is studied and compared by means of numerical models and Hall probe mapping techniques. To this aim, we consider two bulk YBCO samples with a rectangular cross-section that are drilled each by six holes arranged either on a rectangular lattice (sample I) or on a centered rectangular lattice (sample II). For the numerical analysis, three different models are considered for calculating the trapped flux: (i), a two-dimensional (2D) Bean model neglecting demagnetizing effects and flux creep, (ii), a 2D finite-element model neglecting demagnetizing effects but incorporating magnetic relaxation in the form of an E-J power law, and, (iii), a 3D finite element analysis that takes into account both the finite height of the sample and flux creep effects. For the experimental analysis, the trapped magnetic flux density is measured above the sample surface by Hall probe mapping performed before and after the drilling process. The maximum trapped flux density in the drilled samples is found to be smaller than that in the plain samples. The smallest magnetization drop is found for sample II, with the centered rectangular lattice. This result is confirmed by the numerical models. In each sample, the relative drops that are calculated independently with the three different models are in good agreement. As observed experimentally, the magnetization drop calculated in the sample II is the smallest one and its relative value is comparable to the measured one. By contrast, the measured magnetization drop in sample (1) is much larger than that predicted by the simulations, most likely because of a change of the microstructure during the drilling process.
△ Less
Submitted 17 May, 2010;
originally announced May 2010.
-
Pulsed-field magnetization of drilled bulk high-temperature superconductors: flux front propagation in the volume and on the surface
Authors:
Gregory P Lousberg,
J-F Fagnard,
E Haanappel,
X Chaud,
M Ausloos,
B Vanderheyden,
Ph Vanderbemden
Abstract:
We present a method for characterizing the propagation of the magnetic flux in an artificially drilled bulk high-temperature superconductor (HTS) during a pulsed-field magnetization. As the magnetic pulse penetrates the cylindrical sample, the magnetic flux density is measured simultaneously in 16 holes by means of microcoils that are placed across the median plane, i.e. at an equal distance fro…
▽ More
We present a method for characterizing the propagation of the magnetic flux in an artificially drilled bulk high-temperature superconductor (HTS) during a pulsed-field magnetization. As the magnetic pulse penetrates the cylindrical sample, the magnetic flux density is measured simultaneously in 16 holes by means of microcoils that are placed across the median plane, i.e. at an equal distance from the top and bottom surfaces, and close to the surface of the sample. We discuss the time evolution of the magnetic flux density in the holes during a pulse and measure the time taken by the external magnetic flux to reach each hole. Our data show that the flux front moves faster in the median plane than on the surface when penetrating the sample edge; it then proceeds faster along the surface than in the bulk as it penetrates the sample further. Once the pulse is over, the trapped flux density inside the central hole is found to be about twice as large in the median plane than on the surface. This ratio is confirmed by modelling.
△ Less
Submitted 13 August, 2009;
originally announced August 2009.
-
Numerical simulation of the magnetization of high-temperature superconductors: 3D finite element method using a single time-step iteration
Authors:
Gregory P. Lousberg,
Marcel Ausloos,
Christophe Geuzaine,
Patrick Dular,
Philippe Vanderbemden,
Benoit Vanderheyden
Abstract:
We make progress towards a 3D finite-element model for the magnetization of a high temperature superconductor (HTS): We suggest a method that takes into account demagnetisation effects and flux creep, while it neglects the effects associated with currents that are not perpendicular to the local magnetic induction. We consider samples that are subjected to a uniform magnetic field varying linearl…
▽ More
We make progress towards a 3D finite-element model for the magnetization of a high temperature superconductor (HTS): We suggest a method that takes into account demagnetisation effects and flux creep, while it neglects the effects associated with currents that are not perpendicular to the local magnetic induction. We consider samples that are subjected to a uniform magnetic field varying linearly with time. Their magnetization is calculated by means of a weak formulation in the magnetostatic approximation of the Maxwell equations (A-phi formulation). An implicit method is used for the temporal resolution (Backward Euler scheme) and is solved in the open source solver GetDP. Picard iterations are used to deal with the power law conductivity of HTS. The finite element formulation is validated for an HTS tube with large pinning strength through the comparison with results obtained with other well-established methods. We show that carrying the calculations with a single time-step (as opposed to many small time-steps) produce results with excellent accuracy in a drastically reduced simulation time. The numerical method is extended to the study of the trapped magnetization of cylinders that are drilled with different arrays of columnar holes arranged parallel to the cylinder axis.
△ Less
Submitted 18 November, 2008;
originally announced November 2008.
-
Measurement of the magnetic field inside the holes of a drilled bulk high-Tc superconductor
Authors:
Gregory P Lousberg,
Jean-Francois Fagnard,
Jacques G Noudem,
Marcel Ausloos,
Benoit Vanderheyden,
Philippe Vanderbemden
Abstract:
We use macroscopic holes drilled in a bulk YBCO superconductor to probe its magnetic properties in the volume of the sample. The sample is subjected to an AC magnetic flux with a density ranging from 30mT to 130mT and the flux in the superconductor is probed by miniature coils inserted in the holes. In a given hole, three different penetration regimes can be observed: (i) the shielded regime, wh…
▽ More
We use macroscopic holes drilled in a bulk YBCO superconductor to probe its magnetic properties in the volume of the sample. The sample is subjected to an AC magnetic flux with a density ranging from 30mT to 130mT and the flux in the superconductor is probed by miniature coils inserted in the holes. In a given hole, three different penetration regimes can be observed: (i) the shielded regime, where no magnetic flux threads the hole; (ii) the gradual penetration regime, where the waveform of the magnetic field has a clipped sine shape whose fundamental component scales with the applied field; and (iii) the flux concentration regime, where the waveform of the magnetic field is nearly a sine wave, with an amplitude exceeding that of the applied field by up to a factor of two. The distribution of the penetration regimes in the holes is compared with that of the magnetic flux density at the top and bottom surfaces of the sample, and is interpreted with the help of optical polarized light micrographs of these surfaces. We show that the measurement of the magnetic field inside the holes can be used as a local characterization of the bulk magnetic properties of the sample.
△ Less
Submitted 12 November, 2008;
originally announced November 2008.
-
Bulk high-Tc superconductors with drilled holes: how to arrange the holes to maximize the trapped magnetic flux ?
Authors:
Gregory P Lousberg,
M Ausloos,
Ph Vanderbemden,
B Vanderheyden
Abstract:
Drilling holes in a bulk high-Tc superconductor enhances the oxygen annealing and the heat exchange with the cooling liquid. However, drilling holes also reduces the amount of magnetic flux that can be trapped in the sample. In this paper, we use the Bean model to study the magnetization and the current line distribution in drilled samples, as a function of the hole positions. A single hole pert…
▽ More
Drilling holes in a bulk high-Tc superconductor enhances the oxygen annealing and the heat exchange with the cooling liquid. However, drilling holes also reduces the amount of magnetic flux that can be trapped in the sample. In this paper, we use the Bean model to study the magnetization and the current line distribution in drilled samples, as a function of the hole positions. A single hole perturbs the critical current flow over an extended region that is bounded by a discontinuity line, where the direction of the current density changes abruptly. We demonstrate that the trapped magnetic flux is maximized if the center of each hole is positioned on one of the discontinuity lines produced by the neighbouring holes. For a cylindrical sample, we construct a polar triangular hole pattern that exploits this principle; in such a lattice, the trapped field is ~20% higher than in a squared lattice, for which the holes do not lie on discontinuity lines. This result indicates that one can simultaneously enhance the oxygen annealing, the heat transfer, and maximize the trapped field.
△ Less
Submitted 12 November, 2008;
originally announced November 2008.
