-
Substrate temperature dependent dielectric and ferroelectric properties of (100) oriented lead-free Na$_{0.4}$K$_{0.1}$Bi$_{0.5}$TiO$_3$ thin films grown by pulsed laser deposition
Authors:
Krishnarjun Banerjee,
Adityanarayan H. Pandey,
Pravin Varade,
Ajit R. Kulkarni,
Abhijeet L. Sangle,
N. Venkataramani
Abstract:
Pb-free ferroelectric thin films are gaining attention due to their applicability in memory, sensor, actuator, and microelectromechanical system. In this work, Na$_{0.4}$K$_{0.1}$Bi$_{0.5}$TiO$_3$ (NKBT0.1) ferroelectric thin films were deposited on Pt(111)/Ti/SiO$_2$/Si substrates using the pulsed laser deposition technique at various substrate temperatures (600-750 $^\circ$C). The comprehensive…
▽ More
Pb-free ferroelectric thin films are gaining attention due to their applicability in memory, sensor, actuator, and microelectromechanical system. In this work, Na$_{0.4}$K$_{0.1}$Bi$_{0.5}$TiO$_3$ (NKBT0.1) ferroelectric thin films were deposited on Pt(111)/Ti/SiO$_2$/Si substrates using the pulsed laser deposition technique at various substrate temperatures (600-750 $^\circ$C). The comprehensive structural, microstructural, and ferroelectric properties characterizations depicted that the grain size, dielectric constant, and remnant polarization increased with higher deposition temperatures. The influence of higher substrate temperatures on the control of (100)-preferential orientations was observed, indicating the importance of deposition conditions. Significantly, films deposited at 700 deg C exhibited reduced dielectric loss of 0.08 (at 1kHz), high dielectric constant of 673, and remnant polarization of 17 microC/cm2 at room temperature. At this deposition temperature, a maximum effective piezoelectric coefficient of 76 pm/V was availed. Based on the structural analysis, dielectric properties, and ferroelectric behavior, the optimal deposition temperature for the NKBT0.1 thin films was 700 $^\circ$C. This study contributes to the understanding of the influence of substrate temperature on the structural and ferroelectric properties of Pb-free NKBT0.1 thin films, providing insights for the development of high-performance ferroelectric devices.
△ Less
Submitted 6 August, 2023;
originally announced August 2023.
-
Direct and Indirect methods of electrocaloric effect determination and energy storage calculation in (Na0.8K0.2)0.5Bi0.5TiO3 ceramic
Authors:
Pravin Varade,
Adityanarayan H. Pandey,
N. Shara Sowmya,
S. M. Gupta,
Abhay Bhisikar,
N. Venkataramani,
A. R. Kulkarni
Abstract:
The coexistence of multiple structural phases and field induced short-range to long-range order transition in ferroelectric materials, leads to a strong electrocaloric effect (ECE) and electrical energy storage density (Wrec) in the vicinity of ferroelectric to non-ergodic phase transition in NKBT ceramic. Structural analysis using X-ray diffraction, Raman spectroscopy and TEM studies ascertained…
▽ More
The coexistence of multiple structural phases and field induced short-range to long-range order transition in ferroelectric materials, leads to a strong electrocaloric effect (ECE) and electrical energy storage density (Wrec) in the vicinity of ferroelectric to non-ergodic phase transition in NKBT ceramic. Structural analysis using X-ray diffraction, Raman spectroscopy and TEM studies ascertained the coexistence of tetragonal (P4mm) and rhombohedral (R3c) phases. Dielectric study has revealed a critical slowing down of polar domain dynamics below a diffuse phase transition. Present investigation reports ECE in lead-free (Na0.8K0.2)0.5Bi0.5TiO3 (NKBT) ceramic by direct and indirect methods, which confirm the multifunctional nature of NKBT and its usefulness for applications in refrigeration and energy storage. A direct method of EC measurement in NKBT ceramic exhibits significant adiabatic temperature change (ΔT) ~ 1.10 K and electrocaloric strength (ξ) ~ 0.55 Kmm/kV near the ferroelectric to non-ergodic phase transition at an external applied field of 20 kV/cm. A highest recoverable energy (Wrec) ~ 0.78 J/cm3 and electrical storage efficiency (η) ~ 86% are achieved at 423 K and an applied field of 20 kV/cm. This behavior is ascribed to the delicate balance between the field induced order-disordered transition and the thermal energy needed to disrupt field induced co-operative interaction.
△ Less
Submitted 5 August, 2023; v1 submitted 30 July, 2023;
originally announced July 2023.
-
Temperature dependent magnetoelectric response of lead-free Na$_{0.4}$K$_{0.1}$Bi$_{0.5}$TiO$_3$-NiFe$_2$O$_4$ laminated composites
Authors:
Adityanarayan Pandey,
Amritesh Kumar,
Pravin Varade,
K. Miriyala,
A. Arockiarajan,
Ajit. R. Kulkarni,
N. Venkataramani
Abstract:
This study investigates the temperature-dependent quasi-static magnetoelectric (ME) response of electrically poled lead-free Na$_{0.4}$K$_{0.1}$Bi$_{0.5}$TiO$_3$-NiFe$_2$O$_4$ (NKBT-NFO) laminated composites. The aim is to understand the temperature stability of ME-based sensors and devices. The relaxor ferroelectric nature of NKBT is confirmed through impedance and polarization-electric (PE) hyst…
▽ More
This study investigates the temperature-dependent quasi-static magnetoelectric (ME) response of electrically poled lead-free Na$_{0.4}$K$_{0.1}$Bi$_{0.5}$TiO$_3$-NiFe$_2$O$_4$ (NKBT-NFO) laminated composites. The aim is to understand the temperature stability of ME-based sensors and devices. The relaxor ferroelectric nature of NKBT is confirmed through impedance and polarization-electric (PE) hysteresis loop studies, with a depolarization temperature (Td) of approximately 110$^\circ$C. Heating causes a decrease and disappearance of planar electromechanical coupling, charge coefficient, and remnant polarization above Td. The temperature rise also leads to a reduction in magnetostriction and magnetostriction coefficient of NFO by approximately 33% and 25%, respectively, up to approximately 125$^\circ$C. At room temperature, the bilayer and trilayer configurations exhibit maximum ME responses of approximately 33 mV/cm.Oe and 80 mV/cm.Oe, respectively, under low magnetic field conditions (300-450 Oe). The ME response of NKBT/NFO is highly sensitive to temperature, decreasing with heating in accordance with the individual temperature-dependent properties of NKBT and NFO. This study demonstrates a temperature window for the effective utilization of NKBT-NFO-based laminated composite ME devices.
△ Less
Submitted 12 July, 2023;
originally announced July 2023.
-
Performance of dopamine modified 0.5(Ba0.7Ca0.3)TiO3-0.5Ba(Zr0.2Ti0.8)O3 filler in PVDF nanocomposite as flexible energy storage and harvester
Authors:
Chhavi Mitharwal,
Geetanjali,
Shilpa Malhotra,
Manish Kumar Srivastava,
Surya Mohan Gupta,
Chandra Mohan Singh Negi,
Epsita Kar,
Ajit R Kulkarni,
Supratim Mitra
Abstract:
We demonstrate the potential of dopamine modified 0.5(Ba0.7Ca0.3)TiO3-0.5Ba(Zr0.2Ti0.8)O3 filler incorporated poly-vinylidene fluoride (PVDF) composite prepared by solution cast method as both flexible energy storage and harvesting devices. The introduction of dopamine in filler surface functionalization acts as bridging elements between filler and polymer matrix and results in a better filler dis…
▽ More
We demonstrate the potential of dopamine modified 0.5(Ba0.7Ca0.3)TiO3-0.5Ba(Zr0.2Ti0.8)O3 filler incorporated poly-vinylidene fluoride (PVDF) composite prepared by solution cast method as both flexible energy storage and harvesting devices. The introduction of dopamine in filler surface functionalization acts as bridging elements between filler and polymer matrix and results in a better filler dispersion and an improved dielectric loss tangent (<0.02) along with dielectric permittivity ranges from 9 to 34 which is favorable for both energy harvesting and storage. Additionally, a significantly low DC conductivity (< 10-9 ohm-1cm-1) for all composites was achieved leading to an improved breakdown strength and charge accumulation capability. Maximum breakdown strength of 134 KV/mm and corresponding energy storage density 0.72 J/cm3 were obtained from the filler content 10 weight%. The improved energy harvesting performance was characterized by obtaining a maximum piezoelectric charge constant (d33) = 78 pC/N, and output voltage (Vout) = 0.84 V along with maximum power density of 3.46 microW/cm3 for the filler content of 10 wt%. Thus, the results show 0.5(Ba0.7Ca0.3)TiO3-0.5Ba(Zr0.2Ti0.8)O3/PVDF composite has the potential for energy storage and harvesting applications simultaneously that can significantly suppress the excess energy loss arises while utilizing different material.
△ Less
Submitted 17 February, 2021;
originally announced February 2021.
-
Electrical properties of RF sputtered PMN-PT thin films on LCMO buffered platinized glass substrate
Authors:
T. Garg,
A. R. Kulkarni,
N. Venkataramani
Abstract:
Lead based relaxor ferroelectric thin films have been of technological importance due to excellent properties for several commercial applications. However subtleness and high cost of fabrication have plagued of these materials. In this work a systematic study of PMN-PT thin films grown on LCMO buffered platinized glass substrates has been undertaken. The films were grown at room temperature using…
▽ More
Lead based relaxor ferroelectric thin films have been of technological importance due to excellent properties for several commercial applications. However subtleness and high cost of fabrication have plagued of these materials. In this work a systematic study of PMN-PT thin films grown on LCMO buffered platinized glass substrates has been undertaken. The films were grown at room temperature using RF magnetron sputtering. Single phase PMN-PT films could be obtained by exsitu thermal annealing in air for 2h at temperatures 550 and 650 degree C. The films annealed at temperatures lower than 550 degree C and films without buffer layer showed presence of pyrochlore. Effect of annealing temperature on the microstructure, dielectric and ferroelectric properties of the PMN-PT films has been investigated. Scanning electron micrographs of single phase PMN-PT films show a bimodal grain size distribution for films annealed at 550 and 650 degree C. A high dielectric constant of 1300 and a remnant polarization (2Pr) of 17micro C/cm2 were observed for film annealed at 650 degree C.
△ Less
Submitted 25 December, 2015;
originally announced December 2015.
-
Structure, microstructure and electrical properties of new lead-free (1-x)(Li0.12Na0.88)NbO3-xBaTiO3 (0 to x to 40) piezoelectric ceramics
Authors:
Supratim Mitra,
Ajit R. Kulkarni
Abstract:
A new lead-free (1-x)Li0.12Na0.88NbO3-xBaTiO3 (0 to x to 40) piezoelectric ceramics have been prepared using conventional ceramics processing route. Structural analysis revealed an existence of morphotropic phase boundary (MPB), separating orthorhombic and tetragonal phases, between the BaTiO3 content, x = 10-12.5. A partial phase diagram has been established based on temperature-dependent permitt…
▽ More
A new lead-free (1-x)Li0.12Na0.88NbO3-xBaTiO3 (0 to x to 40) piezoelectric ceramics have been prepared using conventional ceramics processing route. Structural analysis revealed an existence of morphotropic phase boundary (MPB), separating orthorhombic and tetragonal phases, between the BaTiO3 content, x = 10-12.5. A partial phase diagram has been established based on temperature-dependent permittivity data for this new system and a nearly vertical temperature-independent MPB is observed. An improvement in electrical properties near MPB (e.g., for x = 12.5; εr = 10489 at Tm, d33 = 30 pC/N, kp = 12.0 %, Qm = 162, Pr = 11.2 μC/cm2, Ec = 19.2 kV/cm, d*33 = 269 pm/V) is observed and is attributed to the ease of polarization rotation due to coexistence of orthorhombic and tetragonal phases. The results show that these materials could be suitable for piezoelectric vibrators and ultrasonic transducers applications. The sample with x = 25, also shows high dielectric permittivity, εr = 3060, and low dielectric loss, tanδ = 0.033 which could be suitable for capacitor (X7R/Z5U) applications.
△ Less
Submitted 23 December, 2014;
originally announced December 2014.
-
Composition induced diffused to relaxor ferroelectric phase transition in lead-free (1-x)(Li0.12Na0.88)NbO3-xBaTiO3 (0 to x to 0.40) ferroelectric ceramics
Authors:
Supratim Mitra,
Ajit R. Kulkarni
Abstract:
(1-x)Li0.12Na0.88NbO3-xBaTiO3 (0 to x to 0.40) ferroelectric ceramics were prepared using conventional ceramics route and their phase transitional behavior is investigated by using dielectric spectroscopy. The temperature-dependent dielectric permittivity epsilon'(T) shows a diffused ferroelectric-paraelectric transition for all compositions. An acceptable and competent characterizing parameter (D…
▽ More
(1-x)Li0.12Na0.88NbO3-xBaTiO3 (0 to x to 0.40) ferroelectric ceramics were prepared using conventional ceramics route and their phase transitional behavior is investigated by using dielectric spectroscopy. The temperature-dependent dielectric permittivity epsilon'(T) shows a diffused ferroelectric-paraelectric transition for all compositions. An acceptable and competent characterizing parameter (D) of diffused phase transition (DPT), defined by Uchino et al. [J Am Ceram Soc 2010;93:4011], was measured and validated. Interestingly, a crossover from diffused ferroelectric phase transition (FE-DPT) to relaxor ferroelectric (RFE) transition is found for the composition x greater than equal to 0.225. The FE-DPT is characterized by a frequency-independent temperature of dielectric maxima (Tm), while a RFE is found to have frequency-dependent Tm satisfying Vogel-Fulcher relation. The composition induced crossover is attributed to the dynamics of different PNR size and relaxation times that varies with different BaTiO3 content (x) leading to the appearance of a FE-DPT or RFE.
△ Less
Submitted 16 December, 2014;
originally announced December 2014.
-
Dielectric relaxation and electrical conductivity in lead-free (100-x)(Li0.12Na0.88)NbO3-xBaTiO3 (0 to x to 40) piezoelectric ceramics: An impedance spectroscopic study
Authors:
Supratim Mitra,
Ajit R Kulkarni
Abstract:
Dielectric behavior and conductivity mechanism in lead-free (100-x)(Li0.12Na0.88)NbO3-xBaTiO3 (0 to x to 40) piezoelectric ceramics were investigated using impedance spectroscopy over a wide temperature (-100 oC to500 oC) and frequency range (0.1 Hz to1 MHz). The grain and grain boundary response as well as the relaxation processes at different frequencies and temperatures were also discussed. A l…
▽ More
Dielectric behavior and conductivity mechanism in lead-free (100-x)(Li0.12Na0.88)NbO3-xBaTiO3 (0 to x to 40) piezoelectric ceramics were investigated using impedance spectroscopy over a wide temperature (-100 oC to500 oC) and frequency range (0.1 Hz to1 MHz). The grain and grain boundary response as well as the relaxation processes at different frequencies and temperatures were also discussed. A low frequency dispersion in dielectric permittivity (LFDD), a typical characteristic of high-temperature behavior was observed both below and above the ferro-paraelectric phase transition temperature, Tm. Oxygen-defect-related complexes generated due to acceptor type doping were found to play an important role in LFDD and hopping conduction. The dielectric relaxation follows Jonscher universal law, however LFDD is found to be associated with quasi-DC process (QCD). The activation energies of DC conduction confirm the mechanism as the thermal motion (short range hopping) of doubly ionized oxygen vacancies. At high temperature, the conductivity relaxation mechanism is dominated by grain boundary conduction through hopping electron created by the charge compensating oxygen vacancies.
△ Less
Submitted 12 June, 2017; v1 submitted 14 January, 2014;
originally announced January 2014.
-
Diffuse phase transition and electrical properties of lead-free piezoelectric (LixNa1-x)NbO3 (0.04 to x to 0.20) ceramics near morphotropic phase boundary
Authors:
S. Mitra,
A. R. Kulkarni,
Om. Prakash
Abstract:
Temperature-dependent dielectric permittivity of lead-free (LixNa1-x)NbO3 for nominal x = 0.04-0.20, prepared by solid state reaction followed by sintering, was studied to resolve often debated issue pertaining to exactness of morphotropic phase boundary (MPB) location along with structural aspects and phase stability in the system near MPB. Interestingly, a diffuse phase transition has been obser…
▽ More
Temperature-dependent dielectric permittivity of lead-free (LixNa1-x)NbO3 for nominal x = 0.04-0.20, prepared by solid state reaction followed by sintering, was studied to resolve often debated issue pertaining to exactness of morphotropic phase boundary (MPB) location along with structural aspects and phase stability in the system near MPB. Interestingly, a diffuse phase transition has been observed in the dielectric permittivity peak arising from the disorder induced in A-site and structural frustration in the perovskite cell due to Li substitution. A partial phase diagram has been proposed based on temperature-dependent dielectric permittivity studies. The room temperature piezoelectric and ferroelectric properties were investigated and the ceramics with x = 0.12 showed relatively good electrical properties (d33 = 28 pC/N, kp = 13.8%, Qm = 440, Pr = 12.5 {micro}C/cm2, EC = 43.2 kV/cm, Tm = 340 oC). These parameter values make this material suitable for piezoelectric resonator and filter applications. Moreover, a high dielectric permittivity (= 2703) with broad diffuse peak near transition temperature along with low dielectric loss (< 4%) in a wide temperature range (50-250 oC) found in this material may also have a potential application in high-temperature multilayer capacitors in automotive and aerospace related industries.
△ Less
Submitted 15 July, 2013;
originally announced July 2013.
