-
Exploration of co-sputtered Ta$_2$O$_5$-ZrO$_2$ thin films for gravitational-wave detectors
Authors:
M. Abernathy,
A. Amato,
A. Ananyeva,
S. Angelova,
B. Baloukas,
R. Bassiri,
G. Billingsley,
R Birney,
G. Cagnoli,
M. Canepa,
M. Coulon,
J. Degallaix,
A. Di Michele,
M. A. Fazio,
M. M. Fejer,
D. Forest,
C. Gier,
M. Granata,
A. M. Gretarsson,
E. M. Gretarsson,
E. Gustafson,
E. J. Hough,
M. Irving,
É. Lalande,
C. Lévesque
, et al. (23 additional authors not shown)
Abstract:
We report on the development and extensive characterization of co-sputtered tantala-zirconia thin films, with the goal to decrease coating Brownian noise in present and future gravitational-wave detectors. We tested a variety of sputtering processes of different energies and deposition rates, and we considered the effect of different values of cation ratio $η=$ Zr/(Zr+Ta) and of post-deposition he…
▽ More
We report on the development and extensive characterization of co-sputtered tantala-zirconia thin films, with the goal to decrease coating Brownian noise in present and future gravitational-wave detectors. We tested a variety of sputtering processes of different energies and deposition rates, and we considered the effect of different values of cation ratio $η=$ Zr/(Zr+Ta) and of post-deposition heat treatment temperature $T_a$ on the optical and mechanical properties of the films. Co-sputtered zirconia proved to be an efficient way to frustrate crystallization in tantala thin films, allowing for a substantial increase of the maximum annealing temperature and hence for a decrease of coating mechanical loss. The lowest average coating loss was observed for an ion-beam sputtered sample with $η= 0.485 \pm 0.004$ annealed at 800 $^{\circ}$C, yielding $\overline{\varphi} = 1.8 \times 10^{-4}$. All coating samples showed cracks after annealing. Although in principle our measurements are sensitive to such defects, we found no evidence that our results were affected. The issue could be solved, at least for ion-beam sputtered coatings, by decreasing heating and cooling rates down to 7 $^{\circ}$C/h. While we observed as little optical absorption as in the coatings of current gravitational-wave interferometers (0.5 parts per million), further development will be needed to decrease light scattering and avoid the formation of defects upon annealing.
△ Less
Submitted 25 March, 2021;
originally announced March 2021.
-
Optical and mechanical properties of ion-beam-sputtered Nb$_2$O$_5$ and TiO$_2$-Nb$_2$O$_5$ thin films for gravitational-wave interferometers
Authors:
N. Demos,
M. Granata,
S. Gras,
A. Amato,
G. Cagnoli,
B. Sassolas,
J. Degallaix,
D. Forest,
C. Michel,
L. Pinard,
M. Evans,
A. Di Michele,
M. Canepa
Abstract:
Brownian thermal noise associated with highly-reflective mirror coatings is a fundamental limit for several precision experiments, including gravitational-wave detectors. Recently, there has been a worldwide effort to find mirror coatings with improved thermal noise properties that also fulfill strict optical requirements such as low absorption and scatter. We report on the optical and mechanical…
▽ More
Brownian thermal noise associated with highly-reflective mirror coatings is a fundamental limit for several precision experiments, including gravitational-wave detectors. Recently, there has been a worldwide effort to find mirror coatings with improved thermal noise properties that also fulfill strict optical requirements such as low absorption and scatter. We report on the optical and mechanical properties of ion-beam-sputtered niobia and titania-niobia thin films, and we discuss application of such coatings in current and future gravitational-wave detectors. We also report an updated direct coating thermal noise measurement of the HR coatings used in Advanced LIGO and Advanced Virgo.
△ Less
Submitted 6 January, 2021;
originally announced January 2021.
-
Amorphous optical coatings of present gravitational-wave interferometers
Authors:
Massimo Granata,
Alex Amato,
Laurent Balzarini,
Maurizio Canepa,
Jérôme Degallaix,
Danièle Forest,
Vincent Dolique,
Lorenzo Mereni,
Christophe Michel,
Laurent Pinard,
Benoît Sassolas,
Julien Teillon,
Gianpietro Cagnoli
Abstract:
We report on the results of an extensive campaign of optical and mechanical characterization of the ion-beam sputtered oxide layers (Ta$_2$O$_5$, TiO$_2$, Ta$_2$O$_5$-TiO$_2$, SiO$_2$) within the high-reflection coatings of the Advanced LIGO, Advanced Virgo and KAGRA gravitational-wave detectors: refractive index, thickness, optical absorption, composition, density, internal friction and elastic c…
▽ More
We report on the results of an extensive campaign of optical and mechanical characterization of the ion-beam sputtered oxide layers (Ta$_2$O$_5$, TiO$_2$, Ta$_2$O$_5$-TiO$_2$, SiO$_2$) within the high-reflection coatings of the Advanced LIGO, Advanced Virgo and KAGRA gravitational-wave detectors: refractive index, thickness, optical absorption, composition, density, internal friction and elastic constants have been measured; the impact of deposition rate and post-deposition annealing on coating internal friction has been assessed. For Ta$_2$O$_5$ and SiO$_2$ layers, coating internal friction increases with the deposition rate, whereas the annealing treatment either erases or largely reduces the gap between samples with different deposition history. For Ta$_2$O$_5$-TiO$_2$ layers, the reduction of internal friction due to TiO$_2$ doping becomes effective only if coupled with annealing. All measured samples showed a weak dependence of internal friction on frequency ($φ_c(f) = af^{b}$, with $-0.208 < b < 0.140$ depending on the coating material considered). SiO$_2$ films showed a mode-dependent loss branching, likely due to spurious losses at the coated edge of the samples. The reference loss values of the Advanced LIGO and Advanced Virgo input (ITM) and end (ETM) mirror HR coatings have been updated by using our estimated value of Young's modulus of Ta$_2$O$_5$-TiO$_2$ layers (120 GPa) and are about 10\% higher than previous estimations.
△ Less
Submitted 9 September, 2019;
originally announced September 2019.
-
Infrared spectroscopy of silicon for applications in astronomy
Authors:
B. Uzakbaiuly,
D. B. Tanner,
J. Ge,
J. Degallaix,
A. S. Markosyan
Abstract:
This work focuses on the characterization of various bulk silicon (Si) samples using Fourier Transform InfraRed (FTIR) and grating spectrometers in order to get them suitable for applications in astronomy. Different samples at different impurity concentrations were characterized by measuring their transmittance in the infrared region. Various lines due to residual impurity absorption were identife…
▽ More
This work focuses on the characterization of various bulk silicon (Si) samples using Fourier Transform InfraRed (FTIR) and grating spectrometers in order to get them suitable for applications in astronomy. Different samples at different impurity concentrations were characterized by measuring their transmittance in the infrared region. Various lines due to residual impurity absorption were identifed and temperature dependence of impurity absorption is presented. Concentrations of doped samples (rho ~ 0.2 - 25000 Ohm cm) were determined from impurity absorption at low temperatures and from Drude free carrier absorption at 300K.
△ Less
Submitted 18 August, 2018;
originally announced August 2018.
-
Measurements of mechanical thermal noise and energy dissipation in optical dielectric coatings
Authors:
Tianjun Li,
Felipe A. Aguilar Sandoval,
Mickael Geitner,
Gianpietro Cagnoli,
Vincent Dolique,
Jérôme Degallaix,
Raffaele Flaminio,
Danièle Forest,
Massimo Granata,
Christophe Michel,
Nazario Morgado,
Laurent Pinard,
Ludovic Bellon
Abstract:
In recent years an increasing number of devices and experiments are shown to be limited by mechanical thermal noise. In particular sub-Hertz laser frequency stabilization and gravitational wave detectors, that are able to measure fluctuations of 1E-18 m/rtHz or less, are being limited by thermal noise in the dielectric coatings deposited on mirrors. In this paper we present a new measurement of th…
▽ More
In recent years an increasing number of devices and experiments are shown to be limited by mechanical thermal noise. In particular sub-Hertz laser frequency stabilization and gravitational wave detectors, that are able to measure fluctuations of 1E-18 m/rtHz or less, are being limited by thermal noise in the dielectric coatings deposited on mirrors. In this paper we present a new measurement of thermal noise in low absorption dielectric coatings deposited on micro-cantilevers and we compare it with the results obtained from the mechanical loss measurements. The coating thermal noise is measured on the widest range of frequencies with the highest signal to noise ratio ever achieved. In addition we present a novel technique to deduce the coating mechanical losses from the measurement of the mechanical quality factor which does not rely on the knowledge of the coating and substrate Young moduli. The dielectric coatings are deposited by ion beam sputtering. The results presented here give a frequency independent loss angle of (4.70 $\pm$ 0.2)x1E-4 with a Young's modulus of 118 GPa for annealed tantala from 10 Hz to 20 kHz. For as-deposited silica, a weak frequency dependence (~ f^{-0.025}) is observed in this frequency range, with a Young's modulus of 70 GPa and an internal damping of (6.0 $\pm$ 0.3)x1E-4 at 16 kHz, but this value decreases by one order of magnitude after annealing and the frequency dependence disappears.
△ Less
Submitted 10 March, 2014; v1 submitted 31 December, 2013;
originally announced January 2014.
