-
A Trapped Field of 17.6 T in Melt-Processed, Bulk Gd-Ba-Cu-O Reinforced with Shrink-Fit Steel
Authors:
John H. Durrell,
Anthony R. Dennis,
Jan Jaroszynski,
Mark D. Ainslie,
Kysen G. B. Palmer,
Yunhua Shi,
Archie M. Campbell,
John Hull,
Mike Strasik,
Eric Hellstrom,
David A. Cardwell
Abstract:
The ability of large grain, REBa$_{2}$Cu$_{3}$O$_{7-δ}$ [(RE)BCO; RE = rare earth] bulk superconductors to trap magnetic field is determined by their critical current. With high trapped fields, however, bulk samples are subject to a relatively large Lorentz force, and their performance is limited primarily by their tensile strength. Consequently, sample reinforcement is the key to performance impr…
▽ More
The ability of large grain, REBa$_{2}$Cu$_{3}$O$_{7-δ}$ [(RE)BCO; RE = rare earth] bulk superconductors to trap magnetic field is determined by their critical current. With high trapped fields, however, bulk samples are subject to a relatively large Lorentz force, and their performance is limited primarily by their tensile strength. Consequently, sample reinforcement is the key to performance improvement in these technologically important materials. In this work, we report a trapped field of 17.6 T, the largest reported to date, in a stack of two, silver-doped GdBCO superconducting bulk samples, each of diameter 25 mm, fabricated by top-seeded melt growth (TSMG) and reinforced with shrink-fit stainless steel. This sample preparation technique has the advantage of being relatively straightforward and inexpensive to implement and offers the prospect of easy access to portable, high magnetic fields without any requirement for a sustaining current source.
△ Less
Submitted 7 July, 2014; v1 submitted 3 June, 2014;
originally announced June 2014.
-
A Trapped Field of >3T in Bulk MgB2 Fabricated by Uniaxial Hot Pressing
Authors:
J. H. Durrell,
C. E. J. Dancer,
A. Dennis,
Y. Shi,
Z. Xu,
A. M. Campbell,
N. H. Babu,
R. I. Todd,
C. R. M. Grovenor,
D. A. Cardwell
Abstract:
A trapped field of over 3 T has been measured at 17.5 K in a magnetised stack of two disc-shaped bulk MgB2 superconductors of diameter 25 mm and thickness 5.4 mm. The bulk MgB2 samples were fabricated by uniaxial hot pressing, which is a readily scalable, industrial technique, to 91% of their maximum theoretical density. The macroscopic critical current density derived from the trapped field data…
▽ More
A trapped field of over 3 T has been measured at 17.5 K in a magnetised stack of two disc-shaped bulk MgB2 superconductors of diameter 25 mm and thickness 5.4 mm. The bulk MgB2 samples were fabricated by uniaxial hot pressing, which is a readily scalable, industrial technique, to 91% of their maximum theoretical density. The macroscopic critical current density derived from the trapped field data using the Biot-Savart law is consistent with the measured local critical current density. From this we conclude that critical current density, and therefore trapped field performance, is limited by the flux pinning available in MgB2, rather than by lack of connectivity. This suggests strongly that both increasing sample size and enhancing pinning through doping will allow further increases in trapped field performance of bulk MgB2.
△ Less
Submitted 28 September, 2012; v1 submitted 30 July, 2012;
originally announced July 2012.
-
Theory and experiment testing flux-line-cutting physics
Authors:
John R. Clem,
Marcus Weigand,
J. H. Durrell,
A. M. Campbell
Abstract:
We discuss predictions of five proposed theories for the critical state of type-II superconductors accounting for both flux cutting and flux transport (depinning). The theories predict different behaviours for the ratio $E_y/E_z$ of the transverse and parallel components of the in-plane electric field produced just above the critical current of a type-II superconducting slab as a function of the a…
▽ More
We discuss predictions of five proposed theories for the critical state of type-II superconductors accounting for both flux cutting and flux transport (depinning). The theories predict different behaviours for the ratio $E_y/E_z$ of the transverse and parallel components of the in-plane electric field produced just above the critical current of a type-II superconducting slab as a function of the angle of an in-plane applied magnetic field. We present experimental results measured using an epitaxially grown YBCO thin film favoring one of the five theories: the extended elliptic critical-state model. We conclude that when the current density $\bm J$ is neither parallel nor perpendicular to the local magnetic flux density $\bm B$, both flux cutting and flux transport occur simultaneously when $J$ exceeds the critical current density $J_c$, indicating an intimate relationship between flux cutting and depinning. We also conclude that the dynamical properties of the superconductor when $J$ exceeds $J_c$ depend in detail upon two nonlinear effective resistivities for flux cutting ($ρ_c$) and flux flow ($ρ_f$) and their ratio $r= ρ_c/ρ_f$.
△ Less
Submitted 7 March, 2011;
originally announced March 2011.
-
Remagnetization of bulk high-temperature superconductors subjected to crossed and rotating magnetic fields
Authors:
P Vanderbemden,
Z Hong,
T A Coombs,
M Ausloos,
N Hari Babu,
D A Cardwell,
A M Campbell
Abstract:
Bulk melt-processed Y-Ba-Cu-O (YBCO) has significant potential for a variety of high field permanent magnet-like applications, such as the rotor of a brushless motor. When used in rotating devices of this kind, however, the YBCO can be subjected to both transient and alternating magnetic fields that are not parallel to the direction of magnetization and which have a detrimental effect on the tra…
▽ More
Bulk melt-processed Y-Ba-Cu-O (YBCO) has significant potential for a variety of high field permanent magnet-like applications, such as the rotor of a brushless motor. When used in rotating devices of this kind, however, the YBCO can be subjected to both transient and alternating magnetic fields that are not parallel to the direction of magnetization and which have a detrimental effect on the trapped field. These effects may lead to a long-term decay of the magnetization of the bulk sample. In the present work, we analyze both experimentally and numerically the remagnetization process of a melt-processed YBCO single domain that has been partially demagnetized by a magnetic field applied orthogonal to the initial direction of trapped flux. Magnetic torque measurements are used as a tool to probe changes in the remanent magnetization during various sequences of applied field. The application of a small magnetic field between the transverse cycles parallel to the direction of original magnetization results in partial remagnetization of the sample. Rotating the applied field, however, is found to be much more efficient at remagnetizing the bulk material than applying a magnetizing field pulse of the same amplitude. The principal features of the experimental data can be reproduced qualitatively using a two-dimensional finite-element numerical model based on an E-J power law. Finally, the remagnetization process is shown to result from the complex modification of current distribution within the cross-section of the bulk sample.
△ Less
Submitted 14 March, 2007;
originally announced March 2007.
-
Behavior of bulk high-temperature superconductors of finite thickness subjected to crossed magnetic fields
Authors:
Ph. Vanderbemden,
Z. Hong,
T. A. Coombs,
S. Denis,
M. Ausloos,
J. Schwartz,
I. B. Rutel,
N. Hari Babu,
D. A. Cardwell,
A. M. Campbell
Abstract:
Crossed magnetic field effects on bulk high-temperature superconductors have been studied both experimentally and numerically. The sample geometry investigated involves finite-size effects along both (crossed) magnetic field directions. The experiments were carried out on bulk melt-processed Y-Ba-Cu-O (YBCO) single domains that had been pre-magnetized with the applied field parallel to their sho…
▽ More
Crossed magnetic field effects on bulk high-temperature superconductors have been studied both experimentally and numerically. The sample geometry investigated involves finite-size effects along both (crossed) magnetic field directions. The experiments were carried out on bulk melt-processed Y-Ba-Cu-O (YBCO) single domains that had been pre-magnetized with the applied field parallel to their shortest direction (i.e. the c-axis) and then subjected to several cycles of the application of a transverse magnetic field parallel to the sample ab plane. The magnetic properties were measured using orthogonal pick-up coils, a Hall probe placed against the sample surface and Magneto-Optical Imaging (MOI). We show that all principal features of the experimental data can be reproduced qualitatively using a two-dimensional finite-element numerical model based on an E-J power law and in which the current density flows perpendicularly to the plane within which the two components of magnetic field are varied. The results of this study suggest that the suppression of the magnetic moment under the action of a transverse field can be predicted successfully by ignoring the existence of flux-free configurations or flux-cutting effects. These investigations show that the observed decay in magnetization results from the intricate modification of current distribution within the sample cross-section. It is also shown that the model does not predict any saturation of the magnetic induction, even after a large number (~ 100) of transverse field cycles. These features are shown to be consistent with the experimental data.
△ Less
Submitted 10 May, 2007; v1 submitted 13 March, 2007;
originally announced March 2007.
-
Thermal Instability and Current-Voltage Scaling in Superconducting Fault Current Limiters
Authors:
Bernhard Zeimetz,
K Tadinada,
D E Eves,
T A Coombs,
J E Evetts,
A M Campbell
Abstract:
We have developed a computer model for the simulation of resistive superconducting fault current limiters in three dimensions. The program calculates the electromagnetic and thermal response of a superconductor to a time-dependent overload voltage, with different possible cooling conditions for the surfaces, and locally variable superconducting and thermal properties. We find that the cryogen bo…
▽ More
We have developed a computer model for the simulation of resistive superconducting fault current limiters in three dimensions. The program calculates the electromagnetic and thermal response of a superconductor to a time-dependent overload voltage, with different possible cooling conditions for the surfaces, and locally variable superconducting and thermal properties. We find that the cryogen boil-off parameters critically influence the stability of a limiter. The recovery time after a fault increases strongly with thickness. Above a critical thickness, the temperature is unstable even for a small applied AC voltage. The maximum voltage and maximum current during a short fault are correlated by a simple exponential law.
△ Less
Submitted 8 December, 2003;
originally announced December 2003.
-
Effects of interlayer coupling on the irreversibility lines of NbN/AlN superconducting multilayers
Authors:
E. S. Sadki,
Z. H. Barber,
S. J. Lloyd,
M. G. Blamire,
A. M. Campbell
Abstract:
We have studied the temperature dependence of the in-plane resistivity of NbN/AlN multilayer samples with varying insulating layer thickness in magnetic fields up to 7 Tesla parallel and perpendicular to the films. The upper critical field shows a crossover from 2D to 3D behavior in parallel fields. The irreversibility lines have the form (1-T/Tc)^alpha, where alpha varies from 4/3 to 2 with inc…
▽ More
We have studied the temperature dependence of the in-plane resistivity of NbN/AlN multilayer samples with varying insulating layer thickness in magnetic fields up to 7 Tesla parallel and perpendicular to the films. The upper critical field shows a crossover from 2D to 3D behavior in parallel fields. The irreversibility lines have the form (1-T/Tc)^alpha, where alpha varies from 4/3 to 2 with increasing anisotropy. The results are consistent with simultaneous melting and decoupling transitions for low anisotropy sample, and with melting of decoupled pancakes in the superconducting layers for higher anisotropy samples.
△ Less
Submitted 24 October, 2000; v1 submitted 27 March, 2000;
originally announced March 2000.
