-
Deposition and photoluminescence of zinc gallium oxide thin films with varied stoichiometry made by reactive magnetron co-sputtering
Authors:
Martins Zubkins,
Edvards Strods,
Viktors Vibornijs,
Anatolijs Sarakovskis,
Ramūnas Nedzinskas,
Reinis Ignatans,
Edgars Butanovs,
Juris Purans,
Andris Azens
Abstract:
This paper reports on the deposition and photoluminescence of amorphous and crystalline thin films of zinc gallium oxide with Ga:Zn atomic ratio varied between 0.3 and 5.7. The films are prepared by reactive direct current magnetron co-sputtering from liquid/solid gallium/zinc targets onto fused quartz substrates; the temperature of the substrate is varied from room temperature (RT) to 800°C. The…
▽ More
This paper reports on the deposition and photoluminescence of amorphous and crystalline thin films of zinc gallium oxide with Ga:Zn atomic ratio varied between 0.3 and 5.7. The films are prepared by reactive direct current magnetron co-sputtering from liquid/solid gallium/zinc targets onto fused quartz substrates; the temperature of the substrate is varied from room temperature (RT) to 800°C. The sputtering process is effectively controlled by fixing the sputtering power of one of the targets and controlling the power of the other target by plasma optical emission spectroscopy. The method, in conjunction with oxygen flow adjustment, enables the production of near-stoichiometric films at any temperature used. The composition analysis suggests a few at.% oxygen deficiency in the films. The resulting deposition rate is at least an order of magnitude higher compared to the commonly used radio-frequency sputtering from a ceramic ZnO:Ga2O3 target. Deposited onto unheated substrates, the films with Ga:Zn {\approx} 2 are X-ray amorphous. Well-defined X-ray diffraction peaks of spinel ZnGa2O4 start to appear at a substrate temperature of 300°C. The surface of the as-deposited films is dense and exhibits a fine-featured structure observed in electron microscopy images. Increasing the deposition temperature from RT to 800°C eliminates defects and improves crystallinity, which for the films with Ga:Zn ratio close to 2 results in an increase in the optical band gap from 4.6 eV to 5.1 eV. Room temperature photoluminescence established the main peak at 3.1 eV (400 nm); a similar peak in Ga2O3 is ascribed to oxygen-vacancy related transitions. A prominent feature around 2.9 eV (428 nm) is attributed to self-activation center of the octahedral Ga-O groups in the spinel lattice of ZnGa2O4. It was found that photoluminescence from ZnGa2O4 depends significantly on the ratio Ga:Zn.
△ Less
Submitted 5 February, 2024;
originally announced February 2024.
-
Comparison of the Resistivities of Nanostructured Films Made from Silver, Copper-Silver and Copper Nanoparticle and Nanowire Suspensions
Authors:
Boris Polyakov,
Aleksandrs Novikovs,
Madara Leimane,
Kevon Kadiwala,
Martins Zubkins,
Edgars Butanovs,
Sven Oras,
Elyad Damerchi,
Veronika Zadin,
Sergei Vlassov
Abstract:
Spray deposition and inkjet printing of various nanostructures are emerging complementary methods for creating conductive coatings on different substrates. In comparison to established deposition techniques like vacuum metal coating and lithography-based metallization processes, spray deposition and inkjet printing benefit from significantly simplified equipment. However, there are number of chall…
▽ More
Spray deposition and inkjet printing of various nanostructures are emerging complementary methods for creating conductive coatings on different substrates. In comparison to established deposition techniques like vacuum metal coating and lithography-based metallization processes, spray deposition and inkjet printing benefit from significantly simplified equipment. However, there are number of challenges related to peculiar properties and behaviour of nanostructures that require additional studies. In present work, we investigate electroconductive properties and sintering behaviour of thin films produced from nanostructures of different metals (Ag, Cu and Cu-Ag) and different shapes (nanowires and spherical nanoparticles), and compare them to the reference Ag and Cu magnetron deposited films. Synthesized nanostructures were studied with transmission electron microscopy. Morphology and crystallinity of produced metal films were studied with scanning electron microscopy and X-ray diffraction. The electrical parameters were measured by the van der Pauw method. All nanowires-based films provided high conductivity and required only modest thermal treatment (200 C). To achieve sufficient sintering and conductivity of nanoparticles-based films, higher temperatures are required (300 C for Ag nanoparticles and 350 C for Cu and Cu-Ag nanoparticles). Additionally, stability of nanowires was studied by annealing the samples in vacuum conditions inside a scanning electron microscope at 500 C.
△ Less
Submitted 19 October, 2023;
originally announced October 2023.
-
Deposition of Ga2O3 thin films by liquid metal target sputtering
Authors:
Martins Zubkins,
Viktors Vibornijs,
Edvards Strods,
Edgars Butanovs,
Liga Bikse,
Mikael Ottosson,
Anders Hallén,
Jevgenijs Gabrusenoks,
Juris Purans,
Andris Azens
Abstract:
This paper reports on the deposition of amorphous and crystalline thin films of Ga2O3 by reactive pulsed direct current magnetron sputtering from a liquid gallium target onto fused (f-) quartz and c plane (c-) sapphire substrates, where the temperature of the substrate is varied from room temperature (RT) to 800°C. The deposition rate (up to 37 nm/min at RT on f-quartz and 5 nm/min at 800°C on c-s…
▽ More
This paper reports on the deposition of amorphous and crystalline thin films of Ga2O3 by reactive pulsed direct current magnetron sputtering from a liquid gallium target onto fused (f-) quartz and c plane (c-) sapphire substrates, where the temperature of the substrate is varied from room temperature (RT) to 800°C. The deposition rate (up to 37 nm/min at RT on f-quartz and 5 nm/min at 800°C on c-sapphire) is two to five times higher than the data given in the literature for radio frequency sputtering. Deposited onto unheated substrates, the films are X-ray amorphous. Well-defined X-ray diffraction peaks of \b{eta}-Ga2O3 start to appear at a substrate temperature of 500°C. Films grown on c-sapphire at temperatures above 600°C are epitaxial. However, the high rocking curve full width at half maximum values of {\approx} 2.4-2.5° are indicative of the presence of defects. A dense and void-free microstructure is observed in electron microscopy images. Composition analysis show stoichiometry close to Ga2O3 and no traces of impurities. The optical properties of low absorptance (<1%) in the visible range and an optical band gap of approximately 5 eV are consistent with the data in the literature for Ga2O3 films produced by other deposition methods.
△ Less
Submitted 10 January, 2023;
originally announced January 2023.
-
The role of Al2O3 interlayer in the synthesis of ZnS/Al2O3/MoS2 core-shell nanowires
Authors:
Edgars Butanovs,
Alexei Kuzmin,
Aleksejs Zolotarjovs,
Sergei Vlassov,
Boris Polyakov
Abstract:
During the synthesis of heterostructured nanomaterials, unwanted structural and morphological changes in nanostructures may occur, especially when multiple sequential growth steps are involved. In this study, we describe a synthesis strategy of heterostructured ZnS/Al2O3/MoS2 core-shell nanowires (NWs), and explore the role of the Al2O3 interlayer during synthesis. Core-shell NWs were produced via…
▽ More
During the synthesis of heterostructured nanomaterials, unwanted structural and morphological changes in nanostructures may occur, especially when multiple sequential growth steps are involved. In this study, we describe a synthesis strategy of heterostructured ZnS/Al2O3/MoS2 core-shell nanowires (NWs), and explore the role of the Al2O3 interlayer during synthesis. Core-shell NWs were produced via a four-step route: 1) synthesis of ZnO NWs on a silicon wafer, 2) deposition of thin Al2O3 layer by ALD, 3) magnetron deposition of MoO3 layer, and 4) annealing of the sample in the sulphur atmosphere. During sulphurization, ZnO is converted into ZnS, and MoO3 into MoS2, while the Al2O3 interlayer preserves the smooth surface of an NW required for the growth of a continuous MoS2 shell. The resulting ZnS/Al2O3/MoS2 core-shell NWs were characterized by transmission electron microscopy, X-ray diffraction and photoelectron spectroscopy, Raman spectroscopy, and optical photoluminescence spectroscopy. A reported strategy can be used for the synthesis of other core-shell NWs with a transition metal dichalcogenides (TMDs) shell to protect the NW core material that may otherwise be altered or damaged by the reactive chalcogenides at high temperatures.
△ Less
Submitted 30 May, 2022;
originally announced May 2022.
-
Different strategies for GaN-MoS2 and GaN-WS2 core-shell nanowire growth
Authors:
Edgars Butanovs,
Kevon Kadiwala,
Aleksejs Gopejenko,
Dmitry Bocharov,
Sergei Piskunov,
Boris Polyakov
Abstract:
One-dimensional (1D) nanostructures - nanowires (NWs) - exhibit promising properties for integration in different types of functional devices. Their properties can be enhanced even further or tuned for a specific application by combining different promising materials, such as layered van der Waals materials and conventional semiconductors, into 1D-1D core-shell heterostructures. In this work, we d…
▽ More
One-dimensional (1D) nanostructures - nanowires (NWs) - exhibit promising properties for integration in different types of functional devices. Their properties can be enhanced even further or tuned for a specific application by combining different promising materials, such as layered van der Waals materials and conventional semiconductors, into 1D-1D core-shell heterostructures. In this work, we demonstrated growth of GaN-MoS2 and GaN-WS2 core-shell NWs via two different methods: (1) two-step process of sputter-deposition of a sacrificial transition metal oxide coating on GaN NWs followed by sulfurization; (2) pulsed laser deposition of few-layer MoS2 or WS2 on GaN NWs from the respective material targets. As-prepared nanostructures were characterized via scanning and transmission electron microscopies, X-ray diffraction, micro-Raman spectroscopy and X-ray photoelectron spectroscopy. High crystalline quality core-shell NW heterostructures with few-layer MoS2 and WS2 shells can be prepared via both routes. The experimental results were supported by theoretical electronic structure calculations, which demonstrated the potential of the synthesised core-shell NW heterostructures as photocatalysts for efficient hydrogen production from water.
△ Less
Submitted 30 May, 2022;
originally announced May 2022.
-
Laser scribing on HOPG for graphene stamp printing on silicon wafer
Authors:
Jelena Butikova,
Boris Polyakov,
Lauris Dimitrocenko,
Edgars Butanovs,
Ivars Tale
Abstract:
Highly oriented pyrolytic graphite (HOPG) was scribed by pulsed laser beam to produce square patterns. Patterning of HOPG surface facilitates the detachment of graphene layers during contact printing. Direct HOPG-to-substrate and glue-assisted stamp printing of a few-layers graphene was compared. Printed graphene sheets were visualized by optical and scanning electron microscopy. The number of gra…
▽ More
Highly oriented pyrolytic graphite (HOPG) was scribed by pulsed laser beam to produce square patterns. Patterning of HOPG surface facilitates the detachment of graphene layers during contact printing. Direct HOPG-to-substrate and glue-assisted stamp printing of a few-layers graphene was compared. Printed graphene sheets were visualized by optical and scanning electron microscopy. The number of graphene layers was measured by atomic force microscopy. Glue-assisted stamp printing allows printing relatively large graphene sheets (40x40 microns) onto a silicon wafer, which can be important for microelectronics fabrication. The presented method is easier to implement and is more flexible than the majority of existing ways of placing graphene sheets onto a substrate.
△ Less
Submitted 21 January, 2013;
originally announced January 2013.
