Showing 1–49 of 49 results for author: Brueckner, F

SOT Enabled 3D Magnetic Field Sensor with Low Offset and High Sensitivity

Authors: Sebastian Zeilinger, Johannes Güttinger, Klemens Prügl, Michael Kirsch, Joshua M. Salazar-Mejía, Sabri Koraltan, Philip Heinrich, Sophie Zeilinger, Bernd Aichner, Florian Bruckner, Hubert Brückl, Armin Satz, Dieter Suess

Abstract: In this work we demonstrate a spin-orbit torque (SOT) magnetic field sensor, designed as a Ta/CoFeB/MgO structure, with high sensitivity and capable of active offset compensation in all three spatial directions. This is described and verified in both experiment and simulation. The measurements of magnetic fields showed an offset of 36, 50, and 37$\mathrm{μT}$ for x-, y-, and z-fields. Furthermore,… ▽ More In this work we demonstrate a spin-orbit torque (SOT) magnetic field sensor, designed as a Ta/CoFeB/MgO structure, with high sensitivity and capable of active offset compensation in all three spatial directions. This is described and verified in both experiment and simulation. The measurements of magnetic fields showed an offset of 36, 50, and 37$\mathrm{μT}$ for x-, y-, and z-fields. Furthermore, the sensitivities of these measurements had values of 590, 580, and 490$\mathrm{V\,A^{-1}\,T^{-1}}$ in the x-, y-, and z-direction. In addition, the robustness to bias fields is demonstrated via experiments and single spin simulations by applying bias fields in y-direction. Cross sensitivities were further analyzed via single spin simulations performing a parameter sweep of different bias fields in the y- and z-direction up to $\pm$1mT. Finally, the extraction of the SOT parameters $η_\mathrm{DL}$ and $η_\mathrm{FL}$ is shown via optimization of a single-spin curve to the experimental measurements. △ Less

Submitted 18 June, 2025; originally announced June 2025.

Comments: 27 pages, 6 figures. Submitted to Physical Review Applied

Inverse-design topology optimization of magnonic devices using level-set method

Authors: Andrey A. Voronov, Marcos Cuervo Santos, Florian Bruckner, Dieter Suess, Andrii V. Chumak, Claas Abert

Abstract: The inverse design approach in magnonics exploits the wave nature of magnons and machine learning to develop logical devices with functionalities that exceed the capabilities of analytical methods. While promising for analog, Boolean, and neuromorphic computing, current implementations face memory limitations that hinder the design of complex systems. This study presents a level-set parameterizati… ▽ More The inverse design approach in magnonics exploits the wave nature of magnons and machine learning to develop logical devices with functionalities that exceed the capabilities of analytical methods. While promising for analog, Boolean, and neuromorphic computing, current implementations face memory limitations that hinder the design of complex systems. This study presents a level-set parameterization method for topology optimization, combined with an adjoint-state approach for memory-efficient simulation of magnetization dynamics. The framework is implemented in NeuralMag, a GPU-accelerated micromagnetic solver featuring a nodal finite-difference scheme and automatic differentiation tools. To validate the method, we optimized the shape of a magnetic nanoparticle by applying constraints to the objective function, and designed a 300-nm-wide yttrium iron garnet demultiplexer achieving frequency-selective spin-wave separation. These results highlight the algorithm's efficiency in exploring local minima across various initial configurations, establishing its utility as a versatile tool for the inverse design of magnonic logic devices. △ Less

Submitted 23 May, 2025; v1 submitted 28 November, 2024; originally announced November 2024.

Realization of inverse-design magnonic logic gates

Authors: Noura Zenbaa, Fabian Majcen, Claas Abert, Florian Bruckner, Norbert J. Mauser, Thomas Schrefl, Qi Wang, Dieter Suess, Andrii V. Chumak

Abstract: Magnonic logic gates represent a crucial step toward realizing fully magnonic data processing systems without reliance on conventional electronic or photonic elements. Recently, a universal and reconfigurable inverse-design device has been developed, featuring a 7$\times$7 array of independent current loops that create local inhomogeneous magnetic fields to scatter spin waves in a Yttrium-Iron-Gar… ▽ More Magnonic logic gates represent a crucial step toward realizing fully magnonic data processing systems without reliance on conventional electronic or photonic elements. Recently, a universal and reconfigurable inverse-design device has been developed, featuring a 7$\times$7 array of independent current loops that create local inhomogeneous magnetic fields to scatter spin waves in a Yttrium-Iron-Garnet film. While initially used for linear RF components, we now demonstrate key non-linear logic gates, NOT, OR, NOR, AND, NAND, and a half-adder, sufficient for building a full processor. In this system, binary data ("0" and "1") are encoded in the spin-wave amplitude. The contrast ratio, representing the difference between logic states, achieved values of 34, 53.9, 11.8, 19.7, 17, and 9.8 dB for these gates, respectively. △ Less

Submitted 26 November, 2024; originally announced November 2024.

Field-free switching of perpendicular magnetic elements by using two orthogonal sub nanosecond spin orbit torque pulses

Authors: Dieter Suess, Claas Abert, Sebastian Zeilinger, Florian Bruckner, Sabri Koraltan

Abstract: We propose a field-free switching mechanism that utilizes two spatially orthogonal spin-orbit torque (SOT) currents. Initially applied simultaneously, one of the currents is subsequently switched off. The superposition of these two currents results in an in-plane magnetization, which is not orthogonal to the remaining SOT current after the second one is deactivated. This symmetry-breaking procedur… ▽ More We propose a field-free switching mechanism that utilizes two spatially orthogonal spin-orbit torque (SOT) currents. Initially applied simultaneously, one of the currents is subsequently switched off. The superposition of these two currents results in an in-plane magnetization, which is not orthogonal to the remaining SOT current after the second one is deactivated. This symmetry-breaking procedure leads to reproducible and rapid switching, with field pulse durations as short as 0.25 nanoseconds. △ Less

Submitted 29 March, 2024; originally announced March 2024.

Skyrmionic device for three dimensional magnetic field sensing enabled by spin-orbit torques

Authors: Sabri Koraltan, Rahul Gupta, Reshma Peremadathil Pradeep, Fabian Kammerbauer, Iryna Kononenko, Klemens Prügl, Michael Kirsch, Bernd Aichner, Santiago Helbig, Florian Bruckner, Claas Abert, Andrada Oana Mandru, Armin Satz, Gerhard Jakob, Hans Josef Hug, Mathias Kläui, Dieter Suess

Abstract: Magnetic skyrmions are topologically protected local magnetic solitons that are promising for storage, logic or general computing applications. In this work, we demonstrate that we can use a skyrmion device based on [W/CoFeB/MgO] 1 0 multilayers for three-dimensional magnetic field sensing enabled by spin-orbit torques (SOT). We stabilize isolated chiral skyrmions and stripe domains in the multila… ▽ More Magnetic skyrmions are topologically protected local magnetic solitons that are promising for storage, logic or general computing applications. In this work, we demonstrate that we can use a skyrmion device based on [W/CoFeB/MgO] 1 0 multilayers for three-dimensional magnetic field sensing enabled by spin-orbit torques (SOT). We stabilize isolated chiral skyrmions and stripe domains in the multilayers, as shown by magnetic force microscopy images and micromagnetic simulations. We perform magnetic transport measurements to show that we can sense both in-plane and out-of-plane magnetic fields by means of a differential measurement scheme in which the symmetry of the SOT leads to cancelation of the DC offset. With the magnetic parameters obtained by vibrating sample magnetometry and ferromagnetic resonance measurements, we perform finite-temperature micromagnetic simulations, where we investigate the fundamental origin of the sensing signal. We identify the topological transformation between skyrmions, stripes and type-II bubbles that leads to a change in the resistance that is read-out by the anomalous Hall effect. Our study presents a novel application for skyrmions, where a differential measurement sensing concept is applied to quantify external magnetic fields paving the way towards more energy efficient applications in skyrmionics based spintronics. △ Less

Submitted 25 March, 2024; originally announced March 2024.

Comments: Main Text: 9 Pages, 6 Figures

Steerable current-driven emission of spin waves in magnetic vortex pairs

Authors: Sabri Koraltan, Katrin Schultheiss, Florian Bruckner, Markus Weigand, Claas Abert, Dieter Suess, Sebastian Wintz

Abstract: The efficient excitation of spin waves is a key challenge in the realization of magnonic devices. We demonstrate the current-driven generation of spin waves in antiferromagnetically coupled magnetic vortices. We employ time-resolved scanning transmission X-ray microscopy (TR-STXM) to directly image the emission of spin waves upon the application of an alternating current flowing directly through t… ▽ More The efficient excitation of spin waves is a key challenge in the realization of magnonic devices. We demonstrate the current-driven generation of spin waves in antiferromagnetically coupled magnetic vortices. We employ time-resolved scanning transmission X-ray microscopy (TR-STXM) to directly image the emission of spin waves upon the application of an alternating current flowing directly through the magnetic stack. Micromagnetic simulations allow us to identify the origin of the excitation to be the current-driven Oersted field, which in the present system proves to be orders of magnitude more efficient than the commonly used excitation via stripline antennas. Our numerical studies also reveal that the spin-transfer torque can lead to the emission of spin waves as well, yet only at much higher current amplitudes. By using magnetostrictive materials, we futhermore demonstrate that the direction of the magnon propagation can be steered by increasing the excitation amplitude, which modifies the underlying magnetization profile through an additional anisotropy in the magnetic layers. The demonstrated methods allow for the efficient and tunable excitation of spin waves, marking a significant advance in the generation and control of spin waves in magnonic devices. △ Less

Submitted 24 February, 2024; originally announced February 2024.

Comments: 12 Pages, 7 Figures, SI: 8 Pages, 8 Figures

Laser-induced real-space topology control of spin wave resonances

Authors: Tim Titze, Sabri Koraltan, Timo Schmidt, Marcel Möller, Florian Bruckner, Claas Abert, Dieter Suess, Claus Ropers, Daniel Steil, Manfred Albrecht, Stefan Mathias

Abstract: Femtosecond laser excitation of materials that exhibit magnetic spin textures promises advanced magnetic control via the generation of ultrafast and non-equilibrium spin dynamics. We explore such possibilities in ferrimagnetic [Fe(0.35 nm)/Gd(0.40 nm)]$_{160}$ multilayers, which host a rich diversity of magnetic textures from stripe domains at low magnetic fields, a dense bubble/skyrmion lattice a… ▽ More Femtosecond laser excitation of materials that exhibit magnetic spin textures promises advanced magnetic control via the generation of ultrafast and non-equilibrium spin dynamics. We explore such possibilities in ferrimagnetic [Fe(0.35 nm)/Gd(0.40 nm)]$_{160}$ multilayers, which host a rich diversity of magnetic textures from stripe domains at low magnetic fields, a dense bubble/skyrmion lattice at intermediate fields, and a single domain state for high magnetic fields. Using femtosecond magneto-optics, we observe distinct coherent spin wave dynamics in response to a weak laser excitation allowing us to unambiguously identify the different magnetic spin textures. Moreover, employing strong laser excitation we show that we achieve versatile control of the coherent spin dynamics via non-equilibrium and ultrafast transformation of magnetic spin textures by both creating and annihilating bubbles/skyrmions. We corroborate our findings by micromagnetic simulations and by Lorentz transmission electron microscopy before and after laser exposure. △ Less

Submitted 22 September, 2023; originally announced September 2023.

Comments: 19 article pages, 12 supplementary

Journal ref: Adv. Funct. Mater. 34, 2313619 (2024)

Single device offset-free magnetic field sensing principle with tunable sensitivity and linear range based on spin-orbit-torques

Authors: Sabri Koraltan, Christin Schmitt, Florian Bruckner, Claas Abert, Klemens Prügl, Michael Kirsch, Rahul Gupta, Sebastian Zeilinger, Joshua M. Salazar-Mejía, Milan Agrawal, Johannes Güttinger, Armin Satz, Gerhard Jakob, Mathias Kläui, Dieter Suess

Abstract: We propose a novel device concept using spin-orbit-torques to realize a magnetic field sensor, where we eliminate the sensor offset using a differential measurement concept. We derive a simple analytical formulation for the sensor signal and demonstrate its validity with numerical investigations using macrospin simulations. The sensitivity and the measurable linear sensing range in the proposed co… ▽ More We propose a novel device concept using spin-orbit-torques to realize a magnetic field sensor, where we eliminate the sensor offset using a differential measurement concept. We derive a simple analytical formulation for the sensor signal and demonstrate its validity with numerical investigations using macrospin simulations. The sensitivity and the measurable linear sensing range in the proposed concept can be tuned by either varying the effective magnetic anisotropy or by varying the magnitude of the injected currents. We show that undesired perturbation fields normal to the sensitive direction preserve the zero-offset property and only slightly modulate the sensitivity of the proposed sensor. Higher-harmonics voltage analysis on a Hall cross experimentally confirms the linearity and tunability via current strength. Additionally, the sensor exhibits a non-vanishing offset in the experiment which we attribute to the anomalous Nernst effect. △ Less

Submitted 23 March, 2023; originally announced March 2023.

Comments: 12 Pages, 7 Figures

Generation and annihilation of skyrmions and antiskyrmions in magnetic heterostructures

Authors: Sabri Koraltan, Claas Abert, Florian Bruckner, Michael Heigl, Manfred Albrecht, Dieter Suess

Abstract: We demonstrate the controlled generation and annihilation of (anti)skyrmions with tunable chirality in magnetic heterostructures by means of micromagnetic simulations. By making use of magnetic (anti)vortices in patterned ferromagnetic layer, we stabilize full lattices of (anti)skyrmions in an underlying skyrmionic thin film in a reproducible manner. The stability of the (anti)skyrmion depends on… ▽ More We demonstrate the controlled generation and annihilation of (anti)skyrmions with tunable chirality in magnetic heterostructures by means of micromagnetic simulations. By making use of magnetic (anti)vortices in patterned ferromagnetic layer, we stabilize full lattices of (anti)skyrmions in an underlying skyrmionic thin film in a reproducible manner. The stability of the (anti)skyrmion depends on the polarization of the (anti)vortex, whereas their chirality is given by those of the (anti)vortices. Furthermore, we demonstrate that the core coupling between the (anti)vortices and (anti)skyrmions allows to annihilate the spin-objects in a controlled fashion by applying short pulses of in-plane external magnetic fields, representing a new key paradigm in skyrmionic devices. △ Less

Submitted 25 July, 2022; originally announced July 2022.

Accurate finite-difference micromagnetics of magnets including RKKY interaction -- analytical solution and comparison to standard micromagnetic codes

Authors: Dieter Suess, Sabri Koraltan, Florian Slanovc, Florian Bruckner, Claas Abert

Abstract: Within this paper we show the importance of accurate implementations of the RKKY interactions for antiferromagnetically coupled ferromagnetic layers with thicknesses exceeding the exchange length. In order to evaluate the performance of different implementations of RKKY interaction, we develop a benchmark problem by deriving the analytical formula for the saturation field of two infinitely thick m… ▽ More Within this paper we show the importance of accurate implementations of the RKKY interactions for antiferromagnetically coupled ferromagnetic layers with thicknesses exceeding the exchange length. In order to evaluate the performance of different implementations of RKKY interaction, we develop a benchmark problem by deriving the analytical formula for the saturation field of two infinitely thick magnetic layers that are antiparallelly coupled. This benchmark problem shows that state-of-the-art implementations in commonly used finite-difference codes lead to errors of the saturation field that amount to more than 20% for mesh sizes of 2 nm which is well below the exchange length of the material. In order to improve the accuracy, we develop higher order cell based and nodal based finite-difference codes that significantly reduce the error compared to state-of-the-art implementations. For the second order cell based and first order nodal based finite element approach the error of the saturation field is reduced by about a factor of 10 (2% error) for the same mesh size of 2 nm. △ Less

Submitted 22 June, 2022; originally announced June 2022.

On the origin of noncollinear magnetization coupling across RuX layers

Authors: Claas Abert, Sabri Koraltan, Florian Bruckner, Florian Slanovc, Juliana Lisik, Pavlo Omelchenko, Erol Girt, Dieter Suess

Abstract: We present a simple atomistic model for the description of noncollinear coupling in magnetic multilayers with hybrid spacer layers made of Ru alloyed to ferromagnetic atoms such as Fe. In contrast to previous analytical and micromagnetic models that explain the noncollinear coupling by means of lateral fluctuations in the coupling constant, the presented model accounts for atom-atom coupling in al… ▽ More We present a simple atomistic model for the description of noncollinear coupling in magnetic multilayers with hybrid spacer layers made of Ru alloyed to ferromagnetic atoms such as Fe. In contrast to previous analytical and micromagnetic models that explain the noncollinear coupling by means of lateral fluctuations in the coupling constant, the presented model accounts for atom-atom coupling in all three spatial dimensions within the spacer layer. The new model is able to accurately predict the dependence of the macroscopic bilinear and biquadratic coupling constants on the spacer-layer composition and thickness, showing much better quantitative agreement than lateral-fluctuation models. Moreover, it predicts noncollinear coupling even for infinitely stiff ferromagnetic layers which goes beyond the predictions of previous models. △ Less

Submitted 21 January, 2022; originally announced January 2022.

Computational Micromagnetics based on Normal Modes: bridging the gap between macrospin and full spatial discretization

Authors: S. Perna, F. Bruckner, C. Serpico, D. Suess, M. d'Aquino

Abstract: The Landau-Lifshitz equation governing magnetization dynamics is written in terms of the amplitudes of normal modes associated with the micromagnetic system's appropriate ground state. This results in a system of nonlinear ordinary differential equations (ODEs), the right-hand side of which can be expressed as the sum of a linear term and nonlinear terms with increasing order of nonlinearity (quad… ▽ More The Landau-Lifshitz equation governing magnetization dynamics is written in terms of the amplitudes of normal modes associated with the micromagnetic system's appropriate ground state. This results in a system of nonlinear ordinary differential equations (ODEs), the right-hand side of which can be expressed as the sum of a linear term and nonlinear terms with increasing order of nonlinearity (quadratic, cubic, etc.). The application of the method to nanostructured magnetic systems demonstrates that the accurate description of magnetization dynamics requires a limited number of normal modes, which results in a considerable improvement in computational speed. The proposed method can be used to obtain a reduced-order dynamical description of magnetic nanostructures which allows to adjust the accuracy between low-dimensional models, such as macrospin, and micromagnetic models with full spatial discretization. This new paradigm for micromagnetic simulations is tested for three problems relevant to the areas of spintronics and magnonics: directional spin-wave coupling in magnonic waveguides, high power ferromagnetic resonance in a magnetic nanodot, and injection-locking in spin-torque nano-oscillators. The case studies considered demonstrate the validity of the proposed approach to systematically obtain an intermediate order dynamical model based on normal modes for the analysis of magnetic nanosystems. The time-consuming calculation of the normal modes has to be done only one time for the system. These modes can be used to optimize and predict the system response for all possible time-varying external excitations (magnetic fields, spin currents). This is of utmost importance for applications where fast and accurate system simulations are required, such as in electronic circuits including magnetic devices. △ Less

Submitted 7 October, 2021; v1 submitted 18 May, 2021; originally announced May 2021.

Tension-free Dirac strings and steered magnetic charges in 3D artificial spin ice

Authors: Sabri Koraltan, Florian Slanovc, Florian Bruckner, Cristiano Nisoli, Andrii V. Chumak, Oleksandr V. Dobrovolskiy, Claas Abert, Dieter Suess

Abstract: 3D nano-architectures present a new paradigm in modern condensed matter physics with numerous applications in photonics, biomedicine, and spintronics. They are promising for the realisation of 3D magnetic nano-networks for ultra-fast and low-energy data storage. Frustration in these systems can lead to magnetic charges or magnetic monopoles, which can function as mobile, binary information carrier… ▽ More 3D nano-architectures present a new paradigm in modern condensed matter physics with numerous applications in photonics, biomedicine, and spintronics. They are promising for the realisation of 3D magnetic nano-networks for ultra-fast and low-energy data storage. Frustration in these systems can lead to magnetic charges or magnetic monopoles, which can function as mobile, binary information carriers. However, Dirac strings in 2D artificial spin ices bind magnetic charges, while 3D dipolar counterparts require cryogenic temperatures for their stability. Here, we present a micromagnetic study of a highly-frustrated 3D artificial spin ice harboring tension-free Dirac strings with unbound magnetic charges at room temperature. We use micromagnetic simulations to demonstrate that the mobility threshold for magnetic charges is by $\SI{2}{eV}$ lower than their unbinding energy. By applying global magnetic fields, we steer magnetic charges in a given direction omitting unintended switchings. The introduced system paves a way towards 3D magnetic networks for data transport and storage △ Less

Submitted 18 February, 2021; originally announced February 2021.

Comments: 7 pages, 4 figures and 1 table

Chiral switching and dynamic barrier reductions in artificial square ice

Authors: Naëmi Leo, Matteo Pancaldi, Sabri Koraltan, Pedro Villalba González, Claas Abert, Christoph Vogler, Florian Slanovc, Florian Bruckner, Paul Heistracher, Kevin Hofhuis, Matteo Menniti, Dieter Suess, Paolo Vavassori

Abstract: Collective dynamics in lithographically-defined artificial spin ices offer profound insights into emergent correlations and phase transitions of geometrically-frustrated Ising spin systems. Their temporal and spatial evolution are often simulated using kinetic Monte Carlo simulations, which rely on the precise knowledge of the switching barriers to obtain predictive results in agreement with exper… ▽ More Collective dynamics in lithographically-defined artificial spin ices offer profound insights into emergent correlations and phase transitions of geometrically-frustrated Ising spin systems. Their temporal and spatial evolution are often simulated using kinetic Monte Carlo simulations, which rely on the precise knowledge of the switching barriers to obtain predictive results in agreement with experimental observations. In many cases, however, the barriers are derived from simplified assumptions only, and do not take into account the full physical picture of nanomagnetic switching. Here we describe how the immediate magnetic environment of a nanomagnet reversing via quasi-coherent rotation can induce clockwise and counter-clockwise switching channels with different barrier energies. This barrier splitting for chiral reversal channels can be sizeable and, as string-method micromagnetic simulations show, is relevant for artificial spin ice systems made of both exchange -- as well as magnetostatically --dominated units. Due to the barrier splitting (and further reductions due to non-uniform reversal) transition rates can be exponentially enhanced by several orders of magnitude compared to mean-field predictions, especially in the limit of rare switching events where thermal excitation is less likely. This leads to significantly faster relaxation time scales and modified spatial correlations. Our findings are thus of integral importance to achieve realistic kinetic Monte Carlo simulations of emergent correlations in artificial spin systems, magnonic crystals, or the evolution of nanomagnetic logic circuits. △ Less

Submitted 21 October, 2020; originally announced October 2020.

Comments: 14 pages, 9 figures

Piezoelectric-driven uniaxial pressure cell for muon spin relaxation and neutron scattering experiments

Authors: Shreenanda Ghosh, Felix Brückner, Artem Nikitin, Vadim Grinenko, Matthias Elender, Andrew P. Mackenzie, Hubertus Luetkens, Hans-Henning Klauss, Clifford W. Hicks

Abstract: We present a piezoelectric-driven uniaxial pressure cell that is optimized for muon spin relaxation and neutron scattering experiments, and that is operable over a wide temperature range including cryogenic temperatures. To accommodate the large samples required for these measurement techniques, the cell is designed to generate forces up to 1000 N, and to minimize the background signal the space a… ▽ More We present a piezoelectric-driven uniaxial pressure cell that is optimized for muon spin relaxation and neutron scattering experiments, and that is operable over a wide temperature range including cryogenic temperatures. To accommodate the large samples required for these measurement techniques, the cell is designed to generate forces up to 1000 N, and to minimize the background signal the space around the sample is kept as open as possible. We demonstrate here that by mounting plate-like samples with epoxy, a uniaxial stress exceeding 1 GPa can be achieved in an active volume of 5 mm3. We show that for practical operation it is important to monitor both the force and displacement applied to the sample. Also, because time is critical during facility experiments, samples are mounted in detachable holders that can be rapidly exchanged. The piezoelectric actuators are likewise contained in an exchangeable cartridge. △ Less

Submitted 12 October, 2020; originally announced October 2020.

Comments: Review of Scientific Instruments accepted for publication Oct 2020, 9 pages, 8 figures

Using uniaxial stress to probe the relationship between competing superconducting states in a cuprate with spin-stripe order

Authors: Z. Guguchia, D. Das, C. N. Wang, T. Adachi, N. Kitajima, M. Elender, F. Brückner, S. Ghosh, V. Grinenko, T. Shiroka, M. Müller, C. Mudry, C. Baines, M. Bartkowiak, Y. Koike, A. Amato, J. M. Tranquada, H. -H. Klauss, C. W. Hicks, H. Luetkens

Abstract: We report muon spin rotation and magnetic susceptibility experiments on in-plane stress effects on the static spin-stripe order and superconductivity in the cuprate system La2-xBaxCuO4 with x = 0.115. An extremely low uniaxial stress of 0.1 GPa induces a substantial decrease in the magnetic volume fraction and a dramatic rise in the onset of 3D superconductivity, from 10 to 32 K; however, the onse… ▽ More We report muon spin rotation and magnetic susceptibility experiments on in-plane stress effects on the static spin-stripe order and superconductivity in the cuprate system La2-xBaxCuO4 with x = 0.115. An extremely low uniaxial stress of 0.1 GPa induces a substantial decrease in the magnetic volume fraction and a dramatic rise in the onset of 3D superconductivity, from 10 to 32 K; however, the onset of at-least-2D superconductivity is much less sensitive to stress. These results show not only that large-volume-fraction spin-stripe order is anti-correlated with 3D superconducting (SC) coherence, but also that these states are energetically very finely balanced. Moreover, the onset temperatures of 3D superconductivity and spin-stripe order are very similar in the large stress regime. These results strongly suggest a similar pairing mechanism for spin-stripe order, the spatially-modulated 2D and uniform 3D SC orders, imposing an important constraint on theoretical models. △ Less

Submitted 3 August, 2020; originally announced August 2020.

Comments: To appear in Physical Review Letters (2020)

Journal ref: Phys. Rev. Lett. 125, 097005 (2020)

Split superconducting and time-reversal symmetry-breaking transitions, and magnetic order in Sr$_2$RuO$_4$ under uniaxial stress

Authors: Vadim Grinenko, Shreenanda Ghosh, Rajib Sarkar, Jean-Christophe Orain, Artem Nikitin, Matthias Elender, Debarchan Das, Zurab Guguchia, Felix Brückner, Mark E. Barber, Joonbum Park, Naoki Kikugawa, Dmitry A. Sokolov, Jake S. Bobowski, Takuto Miyoshi, Yoshiteru Maeno, Andrew P. Mackenzie, Hubertus Luetkens, Clifford W. Hicks, Hans-Henning Klauss

Abstract: Among unconventional superconductors, Sr$_2$RuO$_4$ has become a benchmark for experimentation and theoretical analysis because its normal-state electronic structure is known with exceptional precision, and because of experimental evidence that its superconductivity has, very unusually, a spontaneous angular momentum, i.e. a chiral state. This hypothesis of chirality is however difficult to reconc… ▽ More Among unconventional superconductors, Sr$_2$RuO$_4$ has become a benchmark for experimentation and theoretical analysis because its normal-state electronic structure is known with exceptional precision, and because of experimental evidence that its superconductivity has, very unusually, a spontaneous angular momentum, i.e. a chiral state. This hypothesis of chirality is however difficult to reconcile with recent evidence on the spin part of the order parameter. Measurements under uniaxial stress offer an ideal way to test for chirality, because under uniaxial stress the superconducting and chiral transitions are predicted to split, allowing the empirical signatures of each to be identified separately. Here, we report zerofield muon spin relaxation (ZF-$μ$SR) measurements on crystals placed under uniaxial stresses of up to 1.05 GPa. We report a clear stress-induced splitting between the onset temperatures of superconductivity and time-reversal symmetry breaking, consistent with qualitative expectations for chiral superconductivity. We also report the appearance of unexpected bulk magnetic order under a uniaxial stress of ~ 1.0 GPa in clean Sr$_2$RuO$_4$. △ Less

Submitted 6 February, 2020; v1 submitted 22 January, 2020; originally announced January 2020.

Comments: 28 pages, 12 figures

Journal ref: Nat. Phys. (2021)

Learning magnetization dynamics

Authors: Alexander Kovacs, Johann Fischbacher, Harald Oezelt, Markus Gusenbauer, Lukas Exl, Florian Bruckner, Dieter Suess, Thomas Schrefl

Abstract: Deep neural networks are used to model the magnetization dynamics in magnetic thin film elements. The magnetic states of a thin film element can be represented in a low dimensional space. With convolutional autoencoders a compression ratio of 1024:1 was achieved. Time integration can be performed in the latent space with a second network which was trained by solutions of the Landau-Lifshitz-Gilber… ▽ More Deep neural networks are used to model the magnetization dynamics in magnetic thin film elements. The magnetic states of a thin film element can be represented in a low dimensional space. With convolutional autoencoders a compression ratio of 1024:1 was achieved. Time integration can be performed in the latent space with a second network which was trained by solutions of the Landau-Lifshitz-Gilbert equation. Thus the magnetic response to an external field can be computed quickly. △ Less

Submitted 22 March, 2019; originally announced March 2019.

Stochastic ferrimagnetic Landau-Lifshitz-Bloch equation for finite magnetic structures

Authors: Christoph Vogler, Claas Abert, Florian Bruckner, Dieter Suess

Abstract: Precise modeling of the magnetization dynamics of nanoparticles with finite size effects at fast varying temperatures is a computationally challenging task. Based on the Landau-Lifshitz-Bloch (LLB) equation we derive a coarse grained model for disordered ferrimagnets, which is both fast and accurate. First, we incorporate stochastic fluctuations to the existing ferrimagnetic LLB equation. Further,… ▽ More Precise modeling of the magnetization dynamics of nanoparticles with finite size effects at fast varying temperatures is a computationally challenging task. Based on the Landau-Lifshitz-Bloch (LLB) equation we derive a coarse grained model for disordered ferrimagnets, which is both fast and accurate. First, we incorporate stochastic fluctuations to the existing ferrimagnetic LLB equation. Further, we derive a thermodynamic expression for the temperature dependent susceptibilities, which is essential to model finite size effects. Together with the zero field equilibrium magnetization the susceptibilities are used in the stochastic ferrimagnetic LLB to simulate a $5\times10$ nm$^2$ ferrimagnetic GdFeCo particle with 70 % FeCo and 30 % Gd under various external applied fields and heat pulses. The obtained trajectories agree well with those of an atomistic model, which solves the stochastic Landau-Lifshitz-Gilbert equation for each atom. Additionally, we derive an expression for the intergrain exchange field which couple the ferromagnetic sublattices of a ferrimagnet. A comparison of the magnetization dynamics obtained from this simpler model with those of the ferrimagnetic LLB equation shows a perfect agreement. △ Less

Submitted 5 April, 2018; originally announced April 2018.

Journal ref: Phys. Rev. B 100, 054401 (2019)

Topologically Protected Vortex Structures to Realize Low-Noise Magnetic Sensors

Authors: Dieter Suess, Anton Bachleitner-Hofmann, Armin Satz, Herbert Weitensfelder, Christoph Vogler, Florian Bruckner, Claas Abert, Klemens Prügl, Jürgen Zimmer, Christian Huber, Sebastian Luber, Wolfgang Raberg, Thomas Schrefl, Hubert Brückl

Abstract: Micromagnetic sensors play a major role towards the miniaturization in the industrial society. The adoption of new and emerging sensor technologies like anisotropic magnetoresistance (AMR), giant magnetoresistance (GMR) and tunnel magnetoresistance (TMR) sensors are mainly driven by their integrability and enhanced sensitivity. At the core of such sensors, a microstructured ferromagnetic thin film… ▽ More Micromagnetic sensors play a major role towards the miniaturization in the industrial society. The adoption of new and emerging sensor technologies like anisotropic magnetoresistance (AMR), giant magnetoresistance (GMR) and tunnel magnetoresistance (TMR) sensors are mainly driven by their integrability and enhanced sensitivity. At the core of such sensors, a microstructured ferromagnetic thin film element transduces the magnetic signal. Such elements usually switch via multi-domain, C- or S-shaped magnetization states and, therefore, often exhibit an open non-linear hysteresis curve. Linearity and hysteretic effects, as well as magnetic noise are key features in the improvement of such sensors. Here, we report on the physical origin of these disturbing factors and the inherent connection of noise and hysteresis. Critical noise sources are identified by means of analytic and micromagnetic models. The dominant noise source is due to irreproducible magnetic switching of the transducer element at external fields close to the Stoner Wohlfarth switching field. Furthermore, a solution is presented to overcome these limiting factors: a disruptive sensor design is proposed and analyzed which realizes a topologically protected magnetic vortex state in the transducer element. Compared to state of the art sensors the proposed sensor layout has negligible hysteresis, a linear regime about an order of magnitude higher and lower magnetic noise making the sensor ideal candidate for applications ranging from automotive industry to biological application. △ Less

Submitted 19 December, 2017; originally announced December 2017.

Nematic Fluctuations in Iron-Oxychalcogenide Mott Insulators

Authors: B. Freelon, R. Sarkar, S. Kamusella, F. Brückner, V. Grinenko, Swagata Acharya, Mukul Laad, Luis Craco, Zahra Yamani, Roxana Flacau, Ian Swainson, Benjamin Frandsen, Robert Birgeneau, Yuhao Liu, Bhupendra Karki, Alaa Alfailakawi, Joerg C. Neuefeind, Michelle Everett, Hangdong Wang, Binjie Xu, Minghu Fang, H. -H. Klauss

Abstract: Nematic fluctuations occur in a wide range of physical systems from liquid crystals to biological molecules to solids such as exotic magnets, cuprates and iron-based high-$T_c$ superconductors. Nematic fluctuations are thought to be closely linked to the formation of Cooper-pairs in iron-based superconductors. It is unclear whether the anisotropy inherent in this nematicity arises from electronic… ▽ More Nematic fluctuations occur in a wide range of physical systems from liquid crystals to biological molecules to solids such as exotic magnets, cuprates and iron-based high-$T_c$ superconductors. Nematic fluctuations are thought to be closely linked to the formation of Cooper-pairs in iron-based superconductors. It is unclear whether the anisotropy inherent in this nematicity arises from electronic spin or orbital degrees of freedom. We have studied the iron-based Mott insulators La$_{2}$O$_{2}$Fe$_{2}$O$M$$_{2}$ $M$ = (S, Se) which are structurally similar to the iron pnictide superconductors. They are also in close electronic phase diagram proximity to the iron pnictides. Nuclear magnetic resonance (NMR) revealed a critical slowing down of nematic fluctuations as observed by the spin-lattice relaxation rate ($1/T_1$). This is complemented by the observation of a change of electrical field gradient over a similar temperature range using Mössbauer spectroscopy. The neutron pair distribution function technique applied to the nuclear structure reveals the presence of local nematic $C_2$ fluctuations over a wide temperature range while neutron diffraction indicates that global $C_{4}$ symmetry is preserved. Theoretical modeling of a geometrically frustrated spin-$1$ Heisenberg model with biquadratic and single-ion anisotropic terms provides the interpretation of magnetic fluctuations in terms of hidden quadrupolar spin fluctuations. Nematicity is closely linked to geometrically frustrated magnetism, which emerges from orbital selectivity. The results highlight orbital order and spin fluctuations in the emergence of nematicity in Fe-based oxychalcogenides. The detection of nematic fluctuation within these Mott insulator expands the group of iron-based materials that show short-range symmetry-breaking. △ Less

Submitted 10 February, 2020; v1 submitted 4 August, 2017; originally announced August 2017.

A repulsive skyrmion chain as guiding track for a race track memory

Authors: Dieter Suess, Christoph Vogler, Florian Bruckner, Claas Abert

Abstract: A skyrmion racetrack design is proposed that allows for thermally stable skyrmions to code information and dynamical pinning sites that move with the applied current. This concept solves the problem of intrinsic distributions of pinning times and pinning currents of skyrmions at static geometrical or magnetic pinning sites. The dynamical pinning sites are realized by a skyrmion carrying wire, wher… ▽ More A skyrmion racetrack design is proposed that allows for thermally stable skyrmions to code information and dynamical pinning sites that move with the applied current. This concept solves the problem of intrinsic distributions of pinning times and pinning currents of skyrmions at static geometrical or magnetic pinning sites. The dynamical pinning sites are realized by a skyrmion carrying wire, where the skyrmion repulsion is used in order to keep the skyrmions at equal distances. The information is coded by an additional layer where the presence and absence of a skyrmion is used to code the information. The lowest energy barrier for a data loss is calculated to be DE = 55 kBT300 which is sufficient for long time thermal stability. △ Less

Submitted 21 July, 2017; originally announced July 2017.

AC noise reduction based on exchange coupled grains for heat-assisted-magnetic recording: The effect of an FeRh interlayer

Authors: Christoph Vogler, Claas Abert, Florian Bruckner, Dieter Suess

Abstract: High storage density and high data rate are two of the most desired properties of modern hard disk drives. Heat-assisted magnetic recording (HAMR) is believed to achieve both. Recording media, consisting of exchange coupled grains with a high and a low $T_{\mathrm{C}}$ part, were shown to have low DC noise, but increased AC noise, compared to hard magnetic single phase grains, like FePt [1]. In th… ▽ More High storage density and high data rate are two of the most desired properties of modern hard disk drives. Heat-assisted magnetic recording (HAMR) is believed to achieve both. Recording media, consisting of exchange coupled grains with a high and a low $T_{\mathrm{C}}$ part, were shown to have low DC noise, but increased AC noise, compared to hard magnetic single phase grains, like FePt [1]. In this work we extensively investigate the influence of an FeRh interlayer on the magnetic noise in exchange coupled grains. We find an optimal grain design that reduces the jitter in down-track direction by up to 30 % and in off-track direction by up to 50 %, depending on the head velocity, compared to the same structures without FeRh. Further, the mechanisms causing this jitter reduction are demonstrated. Additionally, we show that for ultrashort heat pulses and low write temperatures the switching time distribution of the analyzed grain structure is reduced by a factor of four, compared to the same structure without FeRh layer. This feature could be interesting for HAMR with a pulsed laser spot and could resume the discussion about this HAMR technique. △ Less

Submitted 7 June, 2017; originally announced June 2017.

Journal ref: Phys. Rev. Applied 8, 054021 (2017)

Spin Torque Efficiency and Analytic Error Rate Estimates of Skyrmion Racetrack Memory

Authors: Dieter Suess, Christoph Vogler, Florian Bruckner, F. Slanovc, Claas Abert

Abstract: In this paper the thermal stability of skyrmion bubbles and the critical currents to move them over pinning sites is investigated. For the used pinning geometries and the used parameters, the unexpected behavior is reported that the energy barrier to overcome the pinning site is larger than the energy barrier of the annihilation of a skyrmion. The annihilation takes place at boundaries by current… ▽ More In this paper the thermal stability of skyrmion bubbles and the critical currents to move them over pinning sites is investigated. For the used pinning geometries and the used parameters, the unexpected behavior is reported that the energy barrier to overcome the pinning site is larger than the energy barrier of the annihilation of a skyrmion. The annihilation takes place at boundaries by current driven motion as well as due to the excitation over energy barriers, in the absence of currents, without forming Bloch points. It is reported that the pinning sites, which are required to allow thermally stable bits, significantly increase the critical current densities to move the bits in skyrmion like structures to about $j_{crit}$ = 0.62 TA/m$^2$. These currents are similar to those obtained experimentally to move stable skyrmions at room temperature. By calculating the thermal stability as well as the critical current, we can derive the spin torque efficiency $η$ = $Δ/I_c = 0.19 k_BT_{300}~/μ$A, which is in a similar range to the simulated spin torque efficiency of MRAM structures. Finally, it is shown that the stochastic depinning process of any racetrack like device requires extremely narrow depinning time distribution smaller than ~6% of the current pulse length to reach bit error rates smaller than ${10^{ - 9}}$. △ Less

Submitted 25 September, 2018; v1 submitted 26 April, 2017; originally announced April 2017.

Efficiently reducing transition curvature in heat-assisted magnetic recording with state-of-the-art write heads

Authors: Christoph Vogler, Claas Abert, Florian Bruckner, Dieter Suess

Abstract: The curvature of bit transitions on granular media is a serious problem for the read-back process. We address this fundamental issue and propose a possibility to efficiently reduce transition curvatures with state-of-the-art heat-assisted magnetic recording (HAMR) heads. We compare footprints of conventional with those of the proposed head design on different media, consisting of exchange coupled… ▽ More The curvature of bit transitions on granular media is a serious problem for the read-back process. We address this fundamental issue and propose a possibility to efficiently reduce transition curvatures with state-of-the-art heat-assisted magnetic recording (HAMR) heads. We compare footprints of conventional with those of the proposed head design on different media, consisting of exchange coupled and single phase grains. Additionally, we investigate the impact of various recording parameters, like the full width at half maximum (FWHM) of the applied heat pulse and the coercivity gradient near the write temperature of the recording grains. The footprints are calculated with a coarse grained model, based on the Landau-Lifshitz-Bloch (LLB) equation. The presented simulations show a transition curvature reduction of up to 40 %, in the case of a medium with exchange coupled grains and a heat pulse with a FWHM of 40 nm. We further give the reason for the straightening of the bit transitions, by means of basic considerations with regard to the effective recording time window (ERTW) of the write process. Besides the transition curvature reduction the proposed head design yields an improvement of the transition jitter in both down-track and off-track direction. △ Less

Submitted 2 March, 2017; originally announced March 2017.

Back hopping in spin-transfer-torque devices, possible origin and counter measures

Authors: Claas Abert, Hossein Sepehri-Amin, Florian Bruckner, Christoph Vogler, Masamitsu Hayashi, Dieter Suess

Abstract: The effect of undesirable high-frequency free-layer switching in magnetic multilayer systems, referred to as back hopping, is investigated by means of the spin-diffusion model. A possible origin of the back-hopping effect is found to be the destabilization of the pinned layer which leads to perpetual switching of both layers. The influence of different material parameters on the critical switching… ▽ More The effect of undesirable high-frequency free-layer switching in magnetic multilayer systems, referred to as back hopping, is investigated by means of the spin-diffusion model. A possible origin of the back-hopping effect is found to be the destabilization of the pinned layer which leads to perpetual switching of both layers. The influence of different material parameters on the critical switching currents for the free and pinned layer is obtained by micromagnetic simulations. It is found that the choice of a free-layer material with low polarization $β$ and saturation magnetization $M_s$, and a pinned-layer material with high $β$ and $M_s$ leads to a low free-layer critical current and a high pinned-layer critical current and hence reduces the likelihood of back hopping. While back hopping was observed in various types of devices, there are only few experiments that exhibit this effect in perpendicularly magnetized systems. However, our simulations suggest, that this is likely to change due to loss of pinned-layer anisotropy when decreasing device sizes. △ Less

Submitted 9 June, 2017; v1 submitted 21 February, 2017; originally announced February 2017.

Journal ref: Phys. Rev. Applied 9, 054010 (2018)

Topology Optimized and 3D Printed Polymer Bonded Permanent Magnets for a Predefined External Field

Authors: Christian Huber, Claas Abert, Florian Bruckner, Martin Groenefeld, Iulian Teliban, Christoph Vogler, Dieter Suess

Abstract: Topology optimization offers great opportunities to design permanent magnetic systems that have specific external field characteristics. Additive manufacturing of polymer bonded magnets with an end-user 3D printer can be used to manufacture permanent magnets with structures that have been difficult or impossible to manufacture previously. This work combines these two powerful methods to design and… ▽ More Topology optimization offers great opportunities to design permanent magnetic systems that have specific external field characteristics. Additive manufacturing of polymer bonded magnets with an end-user 3D printer can be used to manufacture permanent magnets with structures that have been difficult or impossible to manufacture previously. This work combines these two powerful methods to design and manufacture permanent magnetic system with specific properties. The topology optimization framework is simple, fast, and accurate. It can be also used for reverse engineering of permanent magnets in order to find the topology from field measurements. Furthermore, a magnetic system that generate a linear external field above the magnet is presented. With a volume constraint the amount of magnetic material can be minimized without losing performance. Simulations and measurements of the printed system show a very good agreement. △ Less

Submitted 7 February, 2017; originally announced February 2017.

Significant reduction of critical currents in MRAM designs using dual free layer with perpendicular and in-plane anisotropy

Authors: Dieter Suess, Christoph Vogler, Florian Bruckner, Hossein Sepehri-Amin, Claas Abert

Abstract: One essential feature in MRAM cells is the spin torque efficiency, which describes the ratio of the critical switching current to the energy barrier. Within this paper it is reported that the spin torque efficiency can be improved by a factor of 3.2 by the use a of dual free layer device, which consists of one layer with perpendicular crystalline anisotropy and a second layer with in-plane crystal… ▽ More One essential feature in MRAM cells is the spin torque efficiency, which describes the ratio of the critical switching current to the energy barrier. Within this paper it is reported that the spin torque efficiency can be improved by a factor of 3.2 by the use a of dual free layer device, which consists of one layer with perpendicular crystalline anisotropy and a second layer with in-plane crystalline anisotropy. Detailed simulations solving the spin transport equations simultaneously with the micromagnetics equation were performed in order to understand the origin of the switching current reduction by a factor of 4 for the dual layer structure compared to a single layer structure. The main reason could be attributed to an increased spin accumulation within the free layer due to the dynamical tilting of the magnetization within the in-plane region of the dual free layer. △ Less

Submitted 14 February, 2017; v1 submitted 3 February, 2017; originally announced February 2017.

3D Printing of Polymer Bonded Rare-Earth Magnets With a Variable Magnetic Compound Density for a Predefined Stray Field

Authors: Christian Huber, Claas Abert, Florian Bruckner, Martin Groenefeld, Stephan Schuschnigg, Iulian Teliban, Christoph Vogler, Gregor Wautischer, Roman Windl, Dieter Suess

Abstract: Additive manufacturing of polymer bonded magnets is a recently developed technique, for single-unit production, and for structures that have been impossible to manufacture previously. Also new possibilities to create a specific stray field around the magnet are triggered. The current work presents a method to 3D print polymer bonded magnets with a variable magnetic compound density distribution. A… ▽ More Additive manufacturing of polymer bonded magnets is a recently developed technique, for single-unit production, and for structures that have been impossible to manufacture previously. Also new possibilities to create a specific stray field around the magnet are triggered. The current work presents a method to 3D print polymer bonded magnets with a variable magnetic compound density distribution. A low-cost, end-user 3D printer with a mixing extruder is used to mix permanent magnetic filaments with pure PA12 filaments. The magnetic filaments are compounded, extruded, and characterized for the printing process. To deduce the quality of the manufactured magnets with a variable compound density, an inverse stray field framework is used. The effectiveness of the printing process and the simulation method is shown. It can also be used to manufacture magnets that produce a predefined stray field in a given region. Examples for sensor applications are presented. This setup and simulation framework allows the design and manufacturing of polymer bonded permanent magnets which are impossible to create with conventional methods. △ Less

Submitted 26 January, 2017; originally announced January 2017.

Field- and damping-like spin-transfer torque in magnetic multilayers

Authors: Claas Abert, Hossein Sepehri-Amin, Florian Bruckner, Christoph Vogler, Masamitsu Hayashi, Dieter Suess

Abstract: We investigate the spin-transfer torque in a magnetic multilayer structure by means of a spin-diffusion model. The torque in the considered system, consisting of two magnetic layers separated by a conducting layer, is caused by a perpendicular-to-plane current. We compute the strength of the field-like and the damping-like torque for different material parameters and geometries. Our studies sugges… ▽ More We investigate the spin-transfer torque in a magnetic multilayer structure by means of a spin-diffusion model. The torque in the considered system, consisting of two magnetic layers separated by a conducting layer, is caused by a perpendicular-to-plane current. We compute the strength of the field-like and the damping-like torque for different material parameters and geometries. Our studies suggest that the field-like torque highly depends on the exchange coupling strength of the itinerant electrons with the magnetization both in the pinned and the free layer. While a low coupling leads to very high field-like torques, a high coupling leads to low or even negative field-like torques. The dependence of the different torque terms on system parameters is considered very important for the development of applications such as STT MRAM and spin-torque oscillators. △ Less

Submitted 1 December, 2016; originally announced December 2016.

Journal ref: Phys. Rev. Applied 7, 054007 (2017)

Influence of grain size and exchange interaction on the LLB modeling procedure

Authors: Christoph Vogler, Claas Abert, Florian Bruckner, Dieter Suess, Dirk Praetorius

Abstract: Reliably predicting bit-error rates in realistic heat-assisted magnetic recording simulations is a challenging task. Integrating the Landau-Lifshitz-Bloch (LLB) equation can reduce the computational effort to determine the magnetization dynamics in the vicinity of the Curie temperature. If one aims that these dynamics coincide with trajectories calculated from the atomistic Landau-Lifshitz-Gilbert… ▽ More Reliably predicting bit-error rates in realistic heat-assisted magnetic recording simulations is a challenging task. Integrating the Landau-Lifshitz-Bloch (LLB) equation can reduce the computational effort to determine the magnetization dynamics in the vicinity of the Curie temperature. If one aims that these dynamics coincide with trajectories calculated from the atomistic Landau-Lifshitz-Gilbert equation, one has to carefully model required temperature dependent material functions such as the zero-field equilibrium magnetization as well as the parallel and normal susceptibilities. We present an extensive study on how these functions depend on grain size and exchange interactions. We show that, if the size or the exchange constant of a reference grain is modified, the material functions can be scaled, according to the changed Curie temperature, yielding negligible errors. This is shown to be valid for volume changes of up to $\pm 40$ % and variations of the exchange constant of up to $\pm10$ %. Besides the temperature dependent material curves, computed switching probabilities also agree well with probabilities separately determined for each system. Our study suggest that there is no need to recalculate the required LLB input functions for each particle. Within the presented limits it is sufficient to scale them to the Curie temperature of the altered system. △ Less

Submitted 15 July, 2016; originally announced July 2016.

Basic noise mechanisms of heat-assisted-magnetic recording

Authors: Christoph Vogler, Claas Abert, Florian Bruckner, Dieter Suess, Dirk Praetorius

Abstract: Heat-assisted magnetic recording (HAMR) is expected to be a key technology to significantly increase the areal storage density of magnetic recording devices. At high temperatures thermally induced noise becomes a major problem, which must be overcome in order to reliably write magnetic bits with narrow transitions. We propose an elementary model based on the effective recording time window (ERTW)… ▽ More Heat-assisted magnetic recording (HAMR) is expected to be a key technology to significantly increase the areal storage density of magnetic recording devices. At high temperatures thermally induced noise becomes a major problem, which must be overcome in order to reliably write magnetic bits with narrow transitions. We propose an elementary model based on the effective recording time window (ERTW) to compute the switching probability of bits during HARM of bit-patterned media. With few assumptions this analytical model allows to gain deeper insights into the basic noise mechanisms like AC and DC noise. Finally, we discuss strategies to reduce noise and to increase the areal storage density of both bit-patterned as well as granular media. △ Less

Submitted 30 April, 2016; originally announced May 2016.

Spin freezing in the disordered pyrochlore magnet NaCaCo$_2$F$_7$: NMR studies and Monte-Carlo simulations

Authors: R. Sarkar, J. W. Krizan, F. Brückner, E. C. Andrade, S. Rachel, M. Vojta, R. J. Cava, H. -H. Klauss

Abstract: We present results of $^{23}$Na and $^{19}$F nuclear magnetic resonance (NMR) measurements on NaCaCo$_2$F$_7$, a frustrated pyrochlore magnet with a Curie-Weiss temperature, $T_{cw}$ ~-140 K, and intrinsic bond disorder. Below 3.6 K both the $^{23}$Na and $^{19}$F spectra broaden substantially in comparison to higher temperatures accompanied by a considerable reduction (80 \%) of the NMR signal in… ▽ More We present results of $^{23}$Na and $^{19}$F nuclear magnetic resonance (NMR) measurements on NaCaCo$_2$F$_7$, a frustrated pyrochlore magnet with a Curie-Weiss temperature, $T_{cw}$ ~-140 K, and intrinsic bond disorder. Below 3.6 K both the $^{23}$Na and $^{19}$F spectra broaden substantially in comparison to higher temperatures accompanied by a considerable reduction (80 \%) of the NMR signal intensity: This proves a broad quasi-static field distribution. The $^{19}$F spin-lattice relaxation rate $^{19}(1/T_1$) exhibits a peak at 2.9 K already starting to develop below 10 K. We attribute the spin freezing to the presence of bond disorder. This is corroborated by large-scale Monte-Carlo simulations of a classical bond-disordered XY model on the pyrochlore lattice. The low freezing temperature, together with the very short magnetic correlation length not captured by the simulations, suggesting that quantum effects play a decisive role in NaCaCo$_2$F$_7$. △ Less

Submitted 21 September, 2017; v1 submitted 4 April, 2016; originally announced April 2016.

Comments: 11 pages, 11 figures, Substantial changes have been made

Journal ref: Phys. Rev. B 96, 235117 (2017)

A self-consistent spin-diffusion model for micromagnetics

Authors: Claas Abert, Michele Ruggeri, Florian Bruckner, Christoph Vogler, Aurelien Manchon, Dirk Praetorius, Dieter Suess

Abstract: We propose a three-dimensional micromagnetic model that dynamically solves the Landau-Lifshitz-Gilbert equation coupled to the full spin-diffusion equation. In contrast to previous methods, we solve for the magnetization dynamics and the electric potential in a self-consistent fashion. This treatment allows for an accurate description of magnetization dependent resistance changes. Moreover, the pr… ▽ More We propose a three-dimensional micromagnetic model that dynamically solves the Landau-Lifshitz-Gilbert equation coupled to the full spin-diffusion equation. In contrast to previous methods, we solve for the magnetization dynamics and the electric potential in a self-consistent fashion. This treatment allows for an accurate description of magnetization dependent resistance changes. Moreover, the presented algorithm describes both spin accumulation due to smooth magnetization transitions and due to material interfaces as in multilayer structures. The model and its finite-element implementation are validated by current driven motion of a magnetic vortex structure. In a second experiment, the resistivity of a magnetic multilayer structure in dependence of the tilting angle of the magnetization in the different layers is investigated. Both examples show good agreement with reference simulations and experiments respectively. △ Less

Submitted 16 September, 2016; v1 submitted 17 December, 2015; originally announced December 2015.

Areal density optimizations for heat-assisted-magnetic recording of high density bit-patterned media

Authors: Christoph Vogler, Claas Abert, Florian Bruckner, Dieter Suess, Dirk Praetorius

Abstract: Heat-assisted-magnetic recording (HAMR) is hoped to be the future recording technique for high density storage devices. Nevertheless, there exist several realizations strategies. With a coarse-grained Landau-Lifshitz-Bloch (LLB) model we investigate in detail benefits and disadvantages of continuous and pulsed laser spot recording of shingled and conventional bit-patterned media. Additionally we c… ▽ More Heat-assisted-magnetic recording (HAMR) is hoped to be the future recording technique for high density storage devices. Nevertheless, there exist several realizations strategies. With a coarse-grained Landau-Lifshitz-Bloch (LLB) model we investigate in detail benefits and disadvantages of continuous and pulsed laser spot recording of shingled and conventional bit-patterned media. Additionally we compare single phase grains and bits having a bilayer structure with graded Curie temperature, consisting of a hard magnetic layer with high $T_{\mathrm{C}}$ and a soft magnetic one with low $T_{\mathrm{C}}$, respectively. To describe the whole write process as realistic as possible a distribution of the grain sizes and Curie temperatures, a displacement jitter of the head and the bit positions are considered. For all these cases we calculate bit error rates of various grain patterns, temperatures and write head positions to optimize the achievable areal storage density. Within our analysis shingled HAMR with a continuous laser pulse moving over the medium reaches the best results, and thus having the highest potential to become the next generation storage device. △ Less

Submitted 11 December, 2015; originally announced December 2015.

Superior bit error rate and jitter due to improved switching field distribution in exchange spring magnetic recording

Authors: Dieter Suess, Markus Fuger, Claas Abert, Florian Bruckner, Roman Windl, Pietro Palmesi, Anton Buder, Christoph Vogler

Abstract: We report two effects that lead to a reduction of the switching field distribution in exchange spring media. The first effect relies on a subtle mechanism of the interplay between exchange coupling between soft and hard layers and anisotropy that allows significant reduction of the switching field distribution in exchange spring media. This effect reduces the switching field distribution by about… ▽ More We report two effects that lead to a reduction of the switching field distribution in exchange spring media. The first effect relies on a subtle mechanism of the interplay between exchange coupling between soft and hard layers and anisotropy that allows significant reduction of the switching field distribution in exchange spring media. This effect reduces the switching field distribution by about 30% compared to single-phase media. A second effect is that due to the improved thermal stability of exchange spring media over single-phase media, thermal fluctuation leads to reduced fundamental transition jitter. The influence of this overall improved switching field distribution on the transition jitter in granular recording and the bit error rate in bit-patterned magnetic recording is discussed. The transition jitter in granular recording for a distribution of K1 values of 3% in the hard layer, taking into account thermal fluctuations during recording, is estimated to be a = 0.78 nm, which is similar to the best reported calculated jitter in optimized heat-assisted recording media. △ Less

Submitted 15 October, 2015; originally announced October 2015.

Heat assisted magnetic recording of bit patterned media beyond 10 Tb/in$^2$

Authors: Christoph Vogler, Claas Abert, Florian Bruckner, Dieter Suess, Dirk Praetorius

Abstract: The limits of the areal storage density as can be achieved with heat assisted magnetic recording (HAMR) are still an open issue. We want to address this central question and present the design of a possible bit patterned medium with an areal storage density above 10 Tb/in$^2$. The model uses hard magnetic recording grains with 5 nm diameter and 10 nm height. It assumes a realistic distribution of… ▽ More The limits of the areal storage density as can be achieved with heat assisted magnetic recording (HAMR) are still an open issue. We want to address this central question and present the design of a possible bit patterned medium with an areal storage density above 10 Tb/in$^2$. The model uses hard magnetic recording grains with 5 nm diameter and 10 nm height. It assumes a realistic distribution of the Curie temperature of the underlying material as well as a realistic distribution of the grain size and the grain position. In order to compute the areal density we analyze the detailed switching behavior of a recording bit under different external conditions, which allows to compute the bit error rate of a recording process (shingled and conventional) for different grain spacings and write head positions. Hence, we are able to optimize the areal density of the presented medium. △ Less

Submitted 15 October, 2015; v1 submitted 8 October, 2015; originally announced October 2015.

Macroscopic Simulation of Isotropic Permanent Magnets

Authors: Florian Bruckner, Claas Abert, Christoph Vogler, Frank Heinrichs, Armin Satz, Udo Ausserlechner, Gernot Binder, Helmut Koeck, Dieter Suess

Abstract: Accurate simulations of isotropic permanent magnets require to take the magnetization process into account and consider the anisotropic, nonlinear, and hysteretic material behaviour near the saturation configuration. An efficient method for the solution of the magnetostatic Maxwell equations including the description of isotropic permanent magnets is presented. The algorithm can easily be implemen… ▽ More Accurate simulations of isotropic permanent magnets require to take the magnetization process into account and consider the anisotropic, nonlinear, and hysteretic material behaviour near the saturation configuration. An efficient method for the solution of the magnetostatic Maxwell equations including the description of isotropic permanent magnets is presented. The algorithm can easily be implemented on top of existing finite element methods and does not require a full characterization of the hysteresis of the magnetic material. Strayfield measurements of an isotropic permanent magnet and simulation results are in good agreement and highlight the importance of a proper description of the isotropic material. △ Less

Submitted 2 July, 2015; originally announced July 2015.

Calculating thermal stability and attempt frequency of advanced recording structures without free parameters

Authors: Christoph Vogler, Florian Bruckner, Dieter Suess, Christoph Dellago

Abstract: Ensuring a permanent increase of magnetic storage densities is one of the main challenges in magnetic recording. Conventional approaches based on single phase grains are not suitable to achieve this goal, because their grain volume is limited due to the superparamagnetic limit. Grains with graded anisotropy are the most promising candidates to overcome this limit, providing magnetic memory bits wi… ▽ More Ensuring a permanent increase of magnetic storage densities is one of the main challenges in magnetic recording. Conventional approaches based on single phase grains are not suitable to achieve this goal, because their grain volume is limited due to the superparamagnetic limit. Grains with graded anisotropy are the most promising candidates to overcome this limit, providing magnetic memory bits with small volumes, low coercivity and high thermal stability at the same time. Combining micromagnetic simulations with forward flux sampling (FFS), a computational method for rare events that has been recently applied to the magnetic nanostructures, we have determined thermal escape rates and attempt frequencies of a graded media grain and two single phase grains of the same geometry. We find that graded anisotropy can increase the thermal stability of a grain by 12 orders of magnitudes from tens of milliseconds to centuries without changing the coercive field. △ Less

Submitted 16 December, 2014; originally announced December 2014.

Superconducting properties and pseudogap from preformed Cooper pairs in the triclinic (CaFe$_{1-x}$Pt$_x$As)$_{10}$Pt$_3$As$_8$

Authors: M. A. Surmach, F. Brückner, S. Kamusella, R. Sarkar, P. Y. Portnichenko, J. T. Park, G. Ghambashidze, H. Luetkens, P. Biswas, W. J. Choi, Y. I. Seo, Y. S. Kwon, H. -H. Klauss, D. S. Inosov

Abstract: Using a combination of muon-spin relaxation ($μ$SR), inelastic neutron scattering (INS) and nuclear magnetic resonance (NMR), we investigated the novel iron-based superconductor with a triclinic crystal structure (CaFe$_{1-x}$Pt$_x$As)$_{10}$Pt$_3$As$_8$ (T$_{\rm c}$ = 13 K), containing platinum-arsenide intermediary layers. The temperature dependence of the superfluid density obtained from the… ▽ More Using a combination of muon-spin relaxation ($μ$SR), inelastic neutron scattering (INS) and nuclear magnetic resonance (NMR), we investigated the novel iron-based superconductor with a triclinic crystal structure (CaFe$_{1-x}$Pt$_x$As)$_{10}$Pt$_3$As$_8$ (T$_{\rm c}$ = 13 K), containing platinum-arsenide intermediary layers. The temperature dependence of the superfluid density obtained from the $μ$SR relaxation-rate measurements indicates the presence of two superconducting gaps, $Δ_\text{1}\ggΔ_\text{2}$. According to our INS measurements, commensurate spin fluctuations are centered at the ($π$, 0) wave vector, like in most other iron arsenides. Their intensity remains unchanged across T$_\text{c}$, indicating the absence of a spin resonance typical for many Fe-based superconductors. Instead, we observed a peak in the spin-excitation spectrum around $\hslashω_0=\,$7 meV at the same wave vector, which persists above T$_{\rm c}$ and is characterized by the ratio $\hslashω_0/k_\text{B}T_\text{c}\approx\,$6.2, which is significantly higher than typical values for the magnetic resonant modes in iron pnictides (~4.3). The temperature dependence of magnetic intensity at 7 meV revealed an anomaly around T* = 45 K related to the disappearance of this new mode. A suppression of the spin-lattice relaxation rate, $1/T_1T$, observed by NMR immediately below T* without any notable subsequent anomaly at T$_{\rm c}$, indicates that T* could mark the onset of a pseudogap in (CaFe$_{1-x}$Pt$_x$As)$_{10}$Pt$_3$As$_8$, which is likely associated with the emergence of preformed Cooper pairs. △ Less

Submitted 28 November, 2014; originally announced November 2014.

Journal ref: Phys. Rev. B 91, 104515 (2015)

Fundamental limits in heat assisted magnetic recording and methods to overcome it with exchange spring structures

Authors: Dieter Suess, Christoph Vogler, Claas Abert, Florian Bruckner, Roman Windl, Leoni Breth

Abstract: The switching probability of magnetic elements for heat assisted recording is investigated. It is found that FePt elements with a diameter of 5 nm and a height of 10nm show, at a field of 0.5 T, thermally written in errors of 12 percent, which is significant too large for bit patterned magnetic recording. Thermally written in errors can be decreased if larger head fields are applied. However, larg… ▽ More The switching probability of magnetic elements for heat assisted recording is investigated. It is found that FePt elements with a diameter of 5 nm and a height of 10nm show, at a field of 0.5 T, thermally written in errors of 12 percent, which is significant too large for bit patterned magnetic recording. Thermally written in errors can be decreased if larger head fields are applied. However, larger fields lead to an increase the fundamental thermal jitter. This leads to a dilemma between thermally written in errors and fundamental thermal jitter. This dilemma can be partly relaxed by increasing the thickness of the FePt film up to 30nm. For realistic head fields, it is found that the fundamental thermal jitter is in the same order of magnitude of the fundamental thermal jitter in conventional recording, which is about 0.5 to 0.8 nm. Composite structures consisting of high Curie top layer and FePt as hard magnetic storage layer can reduce the thermally written in errors to be smaller than 10-4 if the damping constant is increased in the soft layer. Large damping may be realized by doping with rare earth elements. Similar to single FePt grains also in composite structure an increase of switching probability is sacrifices by an increase of thermal jitter. Structures utilizing first order phase transitions breaking the thermal jitter and writeability dilemma are discussed. △ Less

Submitted 11 November, 2014; originally announced November 2014.

A three-dimensional spin-diffusion model for micromagnetics

Authors: Claas Abert, Michele Ruggeri, Florian Bruckner, Christoph Vogler, Gino Hrkac, Dirk Praetorius, Dieter Suess

Abstract: We implement a finite-element scheme that solves the Landau-Lifshitz-Gilbert equation coupled to a diffusion equation accounting for spin-polarized currents. The latter solves for the spin accumulation not only in magnetic materials but also in nonmagnetic conductors. The presented method incorporates the model by Slonczewski for the description of spin torque in magnetic multilayers as well as th… ▽ More We implement a finite-element scheme that solves the Landau-Lifshitz-Gilbert equation coupled to a diffusion equation accounting for spin-polarized currents. The latter solves for the spin accumulation not only in magnetic materials but also in nonmagnetic conductors. The presented method incorporates the model by Slonczewski for the description of spin torque in magnetic multilayers as well as the model of Zhang and Li for the description of current driven domain-wall motion. Furthermore it is able to do both resolve the time evolution of the spin accumulation or treat it in an adiabatic fashion by the choice of sufficiently large time steps. △ Less

Submitted 18 May, 2015; v1 submitted 22 October, 2014; originally announced October 2014.

Landau-Lifshitz-Bloch equation for exchange coupled grains

Authors: Christoph Vogler, Claas Abert, Florian Bruckner, Dieter Suess

Abstract: Heat assisted recording is a promising technique to further increase the storage density in hard disks. Multilayer recording grains with graded Curie temperature is discussed to further assist the write process. Describing the correct magnetization dynamics of these grains, from room temperature to far above the Curie point, during a write process is required for the calculation of bit error rates… ▽ More Heat assisted recording is a promising technique to further increase the storage density in hard disks. Multilayer recording grains with graded Curie temperature is discussed to further assist the write process. Describing the correct magnetization dynamics of these grains, from room temperature to far above the Curie point, during a write process is required for the calculation of bit error rates. We present a coarse grained approach based on the Landau-Lifshitz-Bloch (LLB) equation to model exchange coupled grains with low computational effort. The required temperature dependent material properties such as the zero-field equilibrium magnetization as well as the parallel and normal susceptibilities are obtained by atomistic Landau-Lifshitz-Gilbert (LLG) simulations. Each grain is described with one magnetization vector. In order to mimic the atomistic exchange interaction between the grains a special treatment of the exchange field in the coarse grained approach is presented. △ Less

Submitted 27 October, 2014; v1 submitted 22 October, 2014; originally announced October 2014.

Coexistence of 3d-ferromagnetism and superconductivity in [(Li(1-x)Fex)OH](Fe(1-y)Liy)Se

Authors: Ursula Pachmayr, Fabian Nitsche, Hubertus Luetkens, Sirko Kamusella, Felix Brückner, Rajib Sarkar, Hans-Hennig Klauss, Dirk Johrendt

Abstract: Superconducting [(Li(1-x)Fex)OH](Fe(1-y)Liy)Se (x ~ 0.2, y ~ 0.08) was synthesized by hydrothermal methods and structurally characterized by single crystal X-ray diffraction. The crystal structure contains anti-PbO type (Fe(1-y)Liy)Se layers separated by layers of (Li(1-x)Fex)OH. Electrical resistivity and magnetic susceptibility measurements reveal superconductivity at 43 K. An anomaly in the dia… ▽ More Superconducting [(Li(1-x)Fex)OH](Fe(1-y)Liy)Se (x ~ 0.2, y ~ 0.08) was synthesized by hydrothermal methods and structurally characterized by single crystal X-ray diffraction. The crystal structure contains anti-PbO type (Fe(1-y)Liy)Se layers separated by layers of (Li(1-x)Fex)OH. Electrical resistivity and magnetic susceptibility measurements reveal superconductivity at 43 K. An anomaly in the diamagnetic shielding indicates ferromagnetic ordering near 10 K while superconductivity is retained. The ferromagnetism emerges from the iron atoms in the (Li(1-x)Fex)OH layer. Isothermal magnetization measurements confirm the superposition of ferromagnetic with superconducting hysteresis. The internal ferromagnetic field is larger than the lower, but smaller than the upper critical field of the superconductor, which gives evidence for a spontaneous vortex phase where both orders coexist. 57Fe-Mössbauer spectra, 7Li-NMR spectra, and muSR experiments consistently support this rare situation, especially in a bulk material where magnetism emerges from a 3d-element. △ Less

Submitted 13 September, 2014; originally announced September 2014.

Comments: 13 pages, 7 Figures

Journal ref: Angew. Chem. Int. Ed. 54 (2015) 293-297

$^{119}$Sn-NMR investigations on superconducting Ca$_3$Ir$_4$Sn$_{13}$: Evidence for multigap superconductivity

Authors: R. Sarkar, F. Brückner, M. Günther, C. Petrovic, Kefeng Wang, P. K. Biswas, H. Luetkens, E. Morenzoni, A. Amato, H-H. Klauss

Abstract: We report bulk superconductivity (SC) in Ca$_3$Ir$_4$Sn$_{13}$ by means of $^{119}$Sn nuclear magnetic resonance (NMR) experiments. Two classical signatures of BCS superconductivity in spin-lattice relaxation rate ($1/T_1$), namely the Hebel-Slichter coherence peak just below the $T_c$ and the exponential decay in the superconducting phase, are evident. The noticeable decrease of $^{119}$Sn Knight… ▽ More We report bulk superconductivity (SC) in Ca$_3$Ir$_4$Sn$_{13}$ by means of $^{119}$Sn nuclear magnetic resonance (NMR) experiments. Two classical signatures of BCS superconductivity in spin-lattice relaxation rate ($1/T_1$), namely the Hebel-Slichter coherence peak just below the $T_c$ and the exponential decay in the superconducting phase, are evident. The noticeable decrease of $^{119}$Sn Knight shift below $T_c$ indicates spin-singlet superconductivity. The temperature dependence of the spin-lattice relaxation rate ($1/T_1$) is convincingly described by the multigap isotropic superconducting gap. Present NMR experiments do not witness any sign of enhanced spin fluctuations in the normal state. △ Less

Submitted 13 June, 2014; originally announced June 2014.

Journal ref: Physica B 479, 51-53(2015)

Multigap superconductivity in locally non-centrosymmetric SrPtAs: An As nuclear quadrupole resonance investigation

Authors: F. Brückner, R. Sarkar, M. Günther, H. Kühne, H. Luetkens, T. Neupert, A. P. Reyes, P. L. Kuhns, P. K. Biswas, T. Stürzer, D. Johrendt, H. -H. Klauss

Abstract: We report detailed $^{75}$As-NQR investigations of the locally non-centrosymmetric superconductor SrPtAs. The spin-lattice relaxation studies prove weakly coupled multi-gap superconductivity. The Hebel-Slichter peak, a hallmark of conventional superconductivity, is strongly suppressed, which points to an unconventional superconducting state. The observed behavior excludes a superconducting order p… ▽ More We report detailed $^{75}$As-NQR investigations of the locally non-centrosymmetric superconductor SrPtAs. The spin-lattice relaxation studies prove weakly coupled multi-gap superconductivity. The Hebel-Slichter peak, a hallmark of conventional superconductivity, is strongly suppressed, which points to an unconventional superconducting state. The observed behavior excludes a superconducting order parameter with line nodes and is consistent with proposed $f$-wave and chiral $d$-wave order parameters. △ Less

Submitted 20 December, 2013; originally announced December 2013.

Journal ref: Phys. Rev. B 90, 220503 (2014)

Evidence for Time-Reversal-Symmetry-Broken Superconductivity in Locally Noncentrosymmetric SrPtAs

Authors: P. K. Biswas, H. Luetkens, T. Neupert, T. Stuerzer, C. Baines, G. Pascua, A. P. Schnyder, M. H. Fischer, J. Goryo, M. R. Lees, H. Maeter, F. Brueckner, H. -H. Klauss, M. Nicklas, P. J. Baker, A. D. Hillier, M. Sigrist, A. Amato, D. Johrendt

Abstract: We report the magnetic and superconducting properties of locally noncentrosymmetric SrPtAs obtained by muon-spin-rotation/relaxation (muSR) measurements. Zero-field muSR reveals the occurrence of small spontaneous static magnetic fields with the onset of superconductivity. This finding suggests that the superconducting state of SrPtAs breaks time-reversal symmetry. The superfluid density as determ… ▽ More We report the magnetic and superconducting properties of locally noncentrosymmetric SrPtAs obtained by muon-spin-rotation/relaxation (muSR) measurements. Zero-field muSR reveals the occurrence of small spontaneous static magnetic fields with the onset of superconductivity. This finding suggests that the superconducting state of SrPtAs breaks time-reversal symmetry. The superfluid density as determined by transverse field muSR is nearly flat approaching T = 0 K proving the absence of extended nodes in the gap function. By symmetry, several superconducting states supporting time-reversal symmetry breaking in SrPtAs are allowed. Out of these, a dominantly d + id (chiral d-wave) order parameter is most consistent with our experimental data. △ Less

Submitted 21 March, 2013; v1 submitted 11 December, 2012; originally announced December 2012.

Comments: Additional experimental results supporting TRS breaking have been added

Calculation of coercivity of magnetic nanostructures at finite temperatures

Authors: D. Suess, L. Breth, J. Lee, M. Fuger, C. Vogler, F. Bruckner, B. Bergmair, T. Huber, J. Fidler, T. Schrefl

Abstract: We report a finite temperature micromagnetic method (FTM) that allows for the calculation of the coercive field of arbitrary shaped magnetic nanostructures at time scales of nanoseconds to years. Instead of directly solving the Landau-Lifshitz-Gilbert equation, the coercive field is obtained without any free parameter by solving a non linear equation, which arises from the transition state theory.… ▽ More We report a finite temperature micromagnetic method (FTM) that allows for the calculation of the coercive field of arbitrary shaped magnetic nanostructures at time scales of nanoseconds to years. Instead of directly solving the Landau-Lifshitz-Gilbert equation, the coercive field is obtained without any free parameter by solving a non linear equation, which arises from the transition state theory. The method is applicable to magnetic structures where coercivity is determined by one thermally activated reversal or nucleation process. The method shows excellent agreement with experimentally obtained coercive fields of magnetic nanostructures and provides a deeper understanding of the mechanism of coercivity. △ Less

Submitted 31 October, 2011; originally announced October 2011.

Comments: submitted to Phys. Rev. B

Investigation of mechanical losses of thin silicon flexures at low temperatures

Authors: R. Nawrodt, C. Schwarz, S. Kroker, I. W. Martin, F. Brückner, L. Cunningham, V. Große, A. Grib, D. Heinert, J. Hough, T. Käsebier, E. B. Kley, R. Neubert, S. Reid, S. Rowan, P. Seidel, M. Thürk, A. Tünnermann

Abstract: The investigation of the mechanical loss of different silicon flexures in a temperature region from 5 to 300 K is presented. The flexures have been prepared by different fabrication techniques. A lowest mechanical loss of $3\times10^{-8}$ was observed for a 130 $μ$m thick flexure at around 10 K. While the mechanical loss follows the thermoelastic predictions down to 50 K a difference can be observ… ▽ More The investigation of the mechanical loss of different silicon flexures in a temperature region from 5 to 300 K is presented. The flexures have been prepared by different fabrication techniques. A lowest mechanical loss of $3\times10^{-8}$ was observed for a 130 $μ$m thick flexure at around 10 K. While the mechanical loss follows the thermoelastic predictions down to 50 K a difference can be observed at lower temperatures for different surface treatments. This surface loss will be limiting for all applications using silicon based oscillators at low temperatures. The extraction of a surface loss parameter using different results from our measurements and other references is presented. We focused on structures that are relevant for gravitational wave detectors. The surface loss parameter $α_s$ = 0.5 pm was obtained. This reveals that the surface loss of silicon is significantly lower than the surface loss of fused silica. △ Less

Submitted 15 March, 2010; originally announced March 2010.

Comments: 16 pages, 7 figures

Journal ref: Class. Quantum Grav. 30, 115008, 2013