Showing 1–12 of 12 results for author: Armstrong, D E J

Deformation Localisation in Ion-Irradiated FeCr

Authors: Kay Song, Dina Sheyfer, Wenjun Liu, Jonathan Z Tischler, Suchandrima Das, Kenichiro Mizohata, Hongbing Yu, David E J Armstrong, Felix Hofmann

Abstract: Irradiation-induced ductility loss is a major concern facing structural steels in next-generation nuclear reactors. Currently, the mechanisms for this are unclear but crucial to address for the design of reactor components. Here, the deformation characteristics around nanoindents in Fe and Fe10Cr irradiated with Fe ions to $\sim$1 displacement-per-atom at 313 K are non-destructively studied. Defor… ▽ More Irradiation-induced ductility loss is a major concern facing structural steels in next-generation nuclear reactors. Currently, the mechanisms for this are unclear but crucial to address for the design of reactor components. Here, the deformation characteristics around nanoindents in Fe and Fe10Cr irradiated with Fe ions to $\sim$1 displacement-per-atom at 313 K are non-destructively studied. Deformation localisation in the irradiated materials is evident from the increased pile-up height and slip step formation, measured by atomic force microscopy. From 3D X-ray Laue diffraction, measurements of lattice rotation and strain fields near the indent site show a large confinement, over 85%, of plasticity in the irradiated material. We find that despite causing increased irradiation hardening, Cr content has little effect on the irradiation-induced changes in pile-up topography and deformation fields. The results demonstrate that varying Cr content in steels has limited impact on retaining strain hardening capacity and reducing irradiation-induced embrittlement. △ Less

Submitted 2 October, 2023; originally announced October 2023.

Comments: 23 pages, 9 figures (1 graphical abstract, 4 figures in main text, 4 figures in supplementary file)

Microstructural and material property changes in severely deformed Eurofer-97

Authors: Kay Song, Guanze He, Abdallah Reza, Tamas Ungár, Phani Karamched, David Yang, Ivan Tolkachev, Kenichiro Mizohata, David E J Armstrong, Felix Hofmann

Abstract: Severe plastic deformation changes the microstructure and properties of steels, which may be favourable for their use in structural components of nuclear reactors. In this study, high-pressure torsion (HPT) was used to refine the grain structure of Eurofer-97, a ferritic/ martensitic steel. Electron microscopy and X-ray diffraction were used to characterise the microstructural changes. Following H… ▽ More Severe plastic deformation changes the microstructure and properties of steels, which may be favourable for their use in structural components of nuclear reactors. In this study, high-pressure torsion (HPT) was used to refine the grain structure of Eurofer-97, a ferritic/ martensitic steel. Electron microscopy and X-ray diffraction were used to characterise the microstructural changes. Following HPT, the average grain size reduced by a factor of $\sim$ 30, with a marked increase in high-angle grain boundaries. Dislocation density also increased by more than one order of magnitude. The thermal stability of the deformed material was investigated via in-situ annealing during synchrotron X-ray diffraction. This revealed substantial recovery between 450 K - 800 K. Irradiation with 20 MeV Fe-ions to $\sim$ 0.1 dpa caused a 20% reduction in dislocation density compared to the as-deformed material. However, HPT deformation prior to irradiation did not have a significant effect in mitigating the irradiation-induced reductions in thermal diffusivity and surface acoustic wave velocity of the material. These results provide a multi-faceted understanding of the changes in ferritic/martensitic steels due to severe plastic deformation, and how these changes can be used to alter material properties. △ Less

Submitted 15 August, 2023; originally announced August 2023.

Comments: 59 pages, 19 figures

Dose and compositional dependence of irradiation-induced property change in FeCr

Authors: Kay Song, Dina Sheyfer, Kenichiro Mizohata, Minyi Zhang, Wenjun Liu, Doğa Gürsoy, David Yang, Ivan Tolkachev, Hongbing Yu, David E J Armstrong, Felix Hofmann

Abstract: Ferritic/martensitic steels will be used as structural components in next generation nuclear reactors. Their successful operation relies on an understanding of irradiation-induced defect behaviour in the material. In this study, Fe and FeCr alloys (3-12%Cr) were irradiated with 20 MeV Fe-ions at 313 K to doses ranging between 0.00008 dpa to 6.0 dpa. This dose range covers six orders of magnitude,… ▽ More Ferritic/martensitic steels will be used as structural components in next generation nuclear reactors. Their successful operation relies on an understanding of irradiation-induced defect behaviour in the material. In this study, Fe and FeCr alloys (3-12%Cr) were irradiated with 20 MeV Fe-ions at 313 K to doses ranging between 0.00008 dpa to 6.0 dpa. This dose range covers six orders of magnitude, spanning low, transition and high dose regimes. Lattice strain and hardness in the irradiated material were characterised with micro-beam Laue X-ray diffraction and nanoindentation, respectively. Irradiation hardening was observed even at very low doses (0.00008 dpa) and showed a monotonic increase with dose up to 6.0 dpa. Lattice strain measurements of samples at 0.0008 dpa allow the calculation of equivalent Frenkel pair densities and corrections to the Norgett-Robinson-Torrens (NRT) model for Fe and FeCr alloys at low dose. NRT efficiency for FeCr is 0.2, which agrees with literature values for high irradiation energy. Lattice strain increases up to 0.8 dpa and then decreases when the damage dose is further increased. The strains measured in this study are lower and peak at a larger dose than predicted by atomistic simulations. This difference can be explained by taking temperature and impurities into account. △ Less

Submitted 4 March, 2024; v1 submitted 1 August, 2023; originally announced August 2023.

Comments: 49 pages, 9 figures, 3 tables

On the Brittle-to-Ductile Transition of the As-cast TiVNbTa Refractory High-entropy Alloy

Authors: Robert James Scales, David Edward John Armstrong, Angus J Wilkinson, Bo-Shiuan Li

Abstract: The fracture properties of as-cast TiVNbTa, a refractory high-entropy alloy (RHEA), were investigated using four-point bending tests from -139C to 20C under a strain-rate of 10-3 s-1. From those tests and fractography, the conditional fracture toughness values and the brittle-to-ductile transition temperature were obtained. The brittle-to-ductile transition temperature was between -47C to -27C, wh… ▽ More The fracture properties of as-cast TiVNbTa, a refractory high-entropy alloy (RHEA), were investigated using four-point bending tests from -139C to 20C under a strain-rate of 10-3 s-1. From those tests and fractography, the conditional fracture toughness values and the brittle-to-ductile transition temperature were obtained. The brittle-to-ductile transition temperature was between -47C to -27C, which gives an estimated activation energy value of 0.52+-0.09 eV for the alloy. This study provides a preliminary understanding of the nature of dislocation motion in a relatively ductile RHEA. △ Less

Submitted 22 October, 2020; originally announced October 2020.

Journal ref: Available online 22 October 2020 in Materialia, 100940

Quantifying the effect of oxygen on micro-mechanical properties of a near-alpha titanium alloy

Authors: H. M. Gardner, P. Gopon, C. M. Magazzeni, A. Radecka, K. Fox, D. Rugg, J. Wade, D. E. J. Armstrong, M. P. Moody, P. A. J. Bagot

Abstract: Atom probe tomography (APT), electron probe microanalysis (EPMA) and nanoindentation were used to characterise the oxygen-rich layer on an in-service jet engine compressor disc, manufactured from the titanium alloy TIMETAL 834. Oxygen ingress was quantified and related to changes in mechanical properties through nanoindentation studies. The relationship between oxygen concentration, microstructure… ▽ More Atom probe tomography (APT), electron probe microanalysis (EPMA) and nanoindentation were used to characterise the oxygen-rich layer on an in-service jet engine compressor disc, manufactured from the titanium alloy TIMETAL 834. Oxygen ingress was quantified and related to changes in mechanical properties through nanoindentation studies. The relationship between oxygen concentration, microstructure, crystal orientation and hardness has been explored through correlative hardness mapping, EPMA and electron backscatter diffraction (EBSD). The role of microstructure on oxygen ingress has been studied and oxygen ingress along a potential alpha/ beta interface was directly observed on the nanoscale using APT. △ Less

Submitted 10 September, 2020; originally announced September 2020.

Nanoindentation in multi-modal map combinations: A Correlative Approach to Local Mechanical Property Assessment

Authors: C. M. Magazzeni, H. M. Gardner, I. Howe, P. Gopon, J. C. Waite, D. Rugg, D. E. J. Armstrong, A. J. Wilkinson

Abstract: A method is presented for the registration and correlation of intrinsic property maps of materials, including data from nanoindentation hardness, Electron Back-Scattered Diffraction (EBSD), Electron Micro-Probe Analysis (EPMA). This highly spatially resolved method allows for the study of micron-scale microstructural features, and has the capability to rapidly extract correlations between multiple… ▽ More A method is presented for the registration and correlation of intrinsic property maps of materials, including data from nanoindentation hardness, Electron Back-Scattered Diffraction (EBSD), Electron Micro-Probe Analysis (EPMA). This highly spatially resolved method allows for the study of micron-scale microstructural features, and has the capability to rapidly extract correlations between multiple features of interest from datasets containing thousands of datapoints. Two case studies are presented in commercially pure (CP) titanium: in the first instance, the effect of crystal anisotropy on measured hardness and, in the second instance, the effect of an oxygen diffusion layer on hardness. The independently collected property maps are registered us-ing affine geometric transformations and are interpolated to allow for direct correlation. The results show strong agreement with trends observed in the literature, as well as providing a large dataset to facilitate future statistical analysis of microstructure-dependent mechanisms. △ Less

Submitted 4 January, 2021; v1 submitted 27 August, 2020; originally announced August 2020.

Comments: 33 pages, 15 figures (9 main body) + graphical abstract, code on Github @XPCorrelate

Atom probe characterisation of segregation driven Cu and Mn-Ni-Si co-precipitation in neutron irradiated T91 tempered-martensitic steel

Authors: T. P. Davis, M. A. Auger, N. Almirall, P. Hosemann, G. R. Odette, P. A. J. Bagot, M. P. Moody, D. E. J. Armstrong

Abstract: The T91 grade and similar 9Cr tempered-martensitic steels (also known as ferritic-martensitic) are leading candidate structural alloys for fast fission nuclear and fusion power reactors. At low temperatures (300 to 400 $^\circ$C) neutron irradiation hardens and embrittles these steels, therefore it is important to investigate the origin of this mode of life limiting property degradation. T91 steel… ▽ More The T91 grade and similar 9Cr tempered-martensitic steels (also known as ferritic-martensitic) are leading candidate structural alloys for fast fission nuclear and fusion power reactors. At low temperatures (300 to 400 $^\circ$C) neutron irradiation hardens and embrittles these steels, therefore it is important to investigate the origin of this mode of life limiting property degradation. T91 steel specimens were separately neutron irradiated to 2.14 dpa at 327 $^\circ$C and 8.82 dpa at 377 $^\circ$C in the Idaho National Laboratory Advanced Test Reactor. Atom probe tomography was used to investigate the segregation driven formation of Mn-Ni-Si-rich (MNSPs) and Cu-rich (CRP) co-precipitates. The precipitates increase in size and, slightly, in volume fraction at the higher irradiation temperature and dose, while their corresponding compositions were very similar, falling near the Si(Mn,Ni) phase field in the Mn-Ni-Si projection of the Fe-based quaternary phase diagram. While the structure of the precipitates has not been characterized, this composition range is distinctly different than that of the typically cited G-phase. The precipitates are composed of CRP with MNSP appendages. Such features are often observed in neutron irradiated reactor pressure vessel (RPV) steels. However, the Si, Ni, Mn, P and Cu solutes concentrations are lower in the T91 than in typical RPV steels. Thus, in T91 precipitation primarily takes place in solute segregated regions of line and loop dislocations. These results are consistent with the model for radiation induced segregation driven precipitation of MNSPs proposed by Ke et al. Cr-rich alpha prime ($α$') phase formation was not observed. △ Less

Submitted 21 July, 2020; originally announced July 2020.

Comments: Pre-print (not peer reviewed)

Characterising Ion-Irradiated FeCr: Hardness, Thermal Diffusivity and Lattice Strain

Authors: Kay Song, Suchandrima Das, Abdallah Reza, Nicholas W. Phillips, Ruqing Xu, Hongbing Yu, Kenichiro Mizohata, David E. J. Armstrong, Felix Hofmann

Abstract: Ion-irradiated FeCr alloys are useful for understanding and predicting neutron-damage in the structural steels of future nuclear reactors. Previous studies have largely focused on the structure of irradiation-induced defects, probed by transmission electron microscopy (TEM), as well as changes in mechanical properties. Across these studies, a wide range of irradiation conditions has been employed… ▽ More Ion-irradiated FeCr alloys are useful for understanding and predicting neutron-damage in the structural steels of future nuclear reactors. Previous studies have largely focused on the structure of irradiation-induced defects, probed by transmission electron microscopy (TEM), as well as changes in mechanical properties. Across these studies, a wide range of irradiation conditions has been employed on samples with different processing histories, which complicates the analysis of the relationship between defect structures and material properties. Furthermore, key properties, such as irradiation-induced changes in thermal transport and lattice strain, are little explored. Here we present a systematic study of Fe3Cr, Fe5Cr and Fe10Cr binary alloys implanted with 20 MeV Fe$^{3+}$ ions to nominal doses of 0.01 dpa and 0.1 dpa at room temperature. Nanoindentation, transient grating spectroscopy (TGS) and X-ray micro-beam Laue diffraction were used to study the changes in hardness, thermal diffusivity and strain in the material as a function of damage and Cr content. Our results suggest that Cr leads to an increased retention of irradiation-induced defects, causing substantial changes in hardness and lattice strain. However, thermal diffusivity varies little with increasing damage and instead degrades significantly with increasing Cr content in the material. We find significant lattice strains even in samples exposed to a nominal displacement damage of 0.01 dpa. The defect density predicted from the lattice strain measurements is significantly higher than that observed in previous TEM studies, suggesting that TEM may not fully capture the irradiation-induced defect population. △ Less

Submitted 2 October, 2020; v1 submitted 19 June, 2020; originally announced June 2020.

Measurement of swelling-induced residual stress in ion implanted SiC, and its effect on micromechanical properties

Authors: Alexander J. Leide, Richard I. Todd, David E. J. Armstrong

Abstract: Ion implantation is widely used as a surrogate for neutron irradiation in the investigation of radiation damage on the properties of materials. Due to the small depth of damage, micromechanical methods must be used to extract material properties. In this work, nanoindentation has been applied to ion irradiated silicon carbide to extract radiation-induced hardening. Residual stress is evaluated usi… ▽ More Ion implantation is widely used as a surrogate for neutron irradiation in the investigation of radiation damage on the properties of materials. Due to the small depth of damage, micromechanical methods must be used to extract material properties. In this work, nanoindentation has been applied to ion irradiated silicon carbide to extract radiation-induced hardening. Residual stress is evaluated using HR-EBSD, AFM swelling measurements, and a novel microcantilever relaxation technique coupled with finite element modelling. Large compressive residual stresses of several GPa are found in the irradiated material, which contribute to the significant hardening observed in nanoindentation measurements. The origin of these residual stresses and the associated hardening is the unirradiated substrate which constrains radiation swelling. Comparisons with other materials susceptible to irradiation swelling show that this effect should not be neglected in studying the effects of ion irradiation damage on mechanical properties. This constraint may also be influencing fundamental radiation defects. This has significant implications for the suitability of ion implantation as a surrogate for neutron irradiations. These results demonstrate the significance of swelling-induced residual stresses in nuclear reactor components, and the impact on structural integrity of reactor components. △ Less

Submitted 30 April, 2020; originally announced April 2020.

Comments: 23 pages, 7 figures

Raman spectroscopy of ion irradiated SiC: chemical defects, strain, annealing, and oxidation

Authors: Alexander J. Leide, Matthew J. Lloyd, Richard I. Todd, David E. J. Armstrong

Abstract: Raman spectroscopy has been used to identify defective bonding in neon and silicon ion irradiated single crystals of 6H-SiC. Observable differences exist in the C-C bonding region corresponding to different defect structures for neon and silicon ion implantations. Raman spectra of ion irradiated SiC show less tensile strain than neutron irradiations, explained by a residual compressive stress caus… ▽ More Raman spectroscopy has been used to identify defective bonding in neon and silicon ion irradiated single crystals of 6H-SiC. Observable differences exist in the C-C bonding region corresponding to different defect structures for neon and silicon ion implantations. Raman spectra of ion irradiated SiC show less tensile strain than neutron irradiations, explained by a residual compressive stress caused by the swelling constrained by the undamaged substrate. Evidence of oxidation during high temperature ion implantation is observed as C-O and Si-O Raman signals. Annealing irradiated SiC while acquiring Raman spectra shows rapid recovery of Si-C bonding, but not a complete recovery of the unirradiated structure. Annealing irradiated SiC causes surface oxidation where unirradiated SiC does not oxidise. Comparisons are made to the apparent radiation resistance of diamond and silicon which have similar crystal structures, but are monatomic, leading to the suggestion that chemical defects are responsible for increased radiation damage in SiC. △ Less

Submitted 2 July, 2020; v1 submitted 29 April, 2020; originally announced April 2020.

Comments: 24 pages, 8 figures

Dislocation interactions during low-temperature plasticity of olivine strengthen the lithospheric mantle

Authors: David Wallis, Lars. N. Hansen, Kathryn M. Kumamoto, Christopher A. Thom, Oliver Plümper, Markus Ohl, William B. Durham, David L. Goldsby, David E. J. Armstrong, Cameron D. Meyers, Rellie Goddard, Jessica M. Warren, Thomas Breithaupt, Martyn R. Drury, Angus J. Wilkinson

Abstract: The strength of the lithosphere is typically modelled based on constitutive equations for steady-state flow. However, models of lithospheric flexure reveal differences in lithospheric strength that are difficult to reconcile based on such flow laws. Recent rheological data from low-temperature deformation experiments on olivine suggest that this discrepancy may be largely explained by strain harde… ▽ More The strength of the lithosphere is typically modelled based on constitutive equations for steady-state flow. However, models of lithospheric flexure reveal differences in lithospheric strength that are difficult to reconcile based on such flow laws. Recent rheological data from low-temperature deformation experiments on olivine suggest that this discrepancy may be largely explained by strain hardening. Details of the mechanical data, specifically the effects of temperature-independent back stresses stored in the samples, indicate that strain hardening in olivine occurs primarily due to long-range elastic interactions between dislocations. These interpretations provided the basis for a new flow law that incorporates hardening by development of back stress. Here, we test this hypothesis by examining the microstructures of olivine samples deformed plastically at room temperature either in a deformation-DIA apparatus at differential stresses of < 4.3 GPa or in a nanoindenter at applied contact stresses of > 10.2 GPa. High-angular resolution electron backscatter diffraction maps reveal the presence of geometrically necessary dislocations with densities commonly above 10$^{14}$ m$^{-2}$ and intragranular heterogeneities in residual stress on the order of 1 GPa in both sets of samples. Scanning transmission electron micrographs reveal straight dislocations aligned along slip bands and interacting with dislocations of other types that act as obstacles. The stress heterogeneities and accumulations of dislocations along their slip planes are consistent with strain hardening resulting from long-range back-stresses acting between dislocations. These results corroborate the mechanical data in supporting the form of the new flow law for low-temperature plasticity and provide new microstructural criteria for identifying the operation of this deformation mechanism in natural samples. △ Less

Submitted 18 September, 2019; originally announced September 2019.

Lattice swelling and modulus change in a helium-implanted tungsten alloy: X-ray micro-diffraction, surface acoustic wave measurements, and multiscale modelling

Authors: F. Hofmann, D. Nguyen-Manh, C. E. Beck, J. K. Eliason, M. R. Gilbert, A. A. Maznev, W. Liu, D. E. J. Armstrong, K. A. Nelson, S. L. Dudarev

Abstract: Using X-ray micro-diffraction and surface acoustic wave spectroscopy, we measure lattice swelling and elastic modulus changes in a W-1%Re alloy after implantation with 3110 appm of helium. A fraction of a percent observed lattice expansion gives rise to an order of magnitude larger reduction in the surface acoustic wave velocity. A multiscale elasticity, molecular dynamics, and density functional… ▽ More Using X-ray micro-diffraction and surface acoustic wave spectroscopy, we measure lattice swelling and elastic modulus changes in a W-1%Re alloy after implantation with 3110 appm of helium. A fraction of a percent observed lattice expansion gives rise to an order of magnitude larger reduction in the surface acoustic wave velocity. A multiscale elasticity, molecular dynamics, and density functional theory model is applied to the interpretation of observations. The measured lattice swelling is consistent with the relaxation volume of self-interstitial and helium-filled vacancy defects that dominate the helium-implanted material microstructure. Molecular dynamics simulations confirm the elasticity model for swelling. Elastic properties of the implanted surface layer also change due to defects. The reduction of surface acoustic wave velocity predicted by density functional theory calculations agrees remarkably well with experimental observations. △ Less

Submitted 22 July, 2014; originally announced July 2014.

Comments: 36 pages, 6 figures, 3 tables. Presented at MRS Spring 2014