-
Relaxed current matching requirements in highly luminescent perovskite tandem solar cells and their fundamental efficiency limits
Authors:
Alan R. Bowman,
Felix Lang,
Yu-Hsien Chiang,
Alberto Jiménez-Solano,
Kyle Frohna,
Giles E. Eperon,
Edoardo Ruggeri,
Mojtaba Abdi-Jalebi,
Miguel Anaya,
Bettina V. Lotsch,
Samuel D. Stranks
Abstract:
Here we use time-resolved and steady-state optical spectroscopy on state-of-the-art low- and high-bandgap perovskite films for tandems to quantify intrinsic recombination rates and absorption coefficients. We apply these data to calculate the limiting efficiency of perovskite-silicon and all-perovskite two-terminal tandems employing currently available bandgap materials as 42.0 % and 40.8 % respec…
▽ More
Here we use time-resolved and steady-state optical spectroscopy on state-of-the-art low- and high-bandgap perovskite films for tandems to quantify intrinsic recombination rates and absorption coefficients. We apply these data to calculate the limiting efficiency of perovskite-silicon and all-perovskite two-terminal tandems employing currently available bandgap materials as 42.0 % and 40.8 % respectively. By including luminescence coupling between sub-cells, i.e. the re-emission of photons from the high-bandgap sub-cell and their absorption in the low-bandgap sub-cell, we reveal the stringent need for current matching is relaxed when the high-bandgap sub-cell is a luminescent perovskite compared to calculations that do not consider luminescence coupling. We show luminescence coupling becomes important in all-perovskite tandems when charge carrier trapping rates are < 10$^{6}$ s$^{-1}$ (corresponding to carrier lifetimes longer than 1 $μ$s at low excitation densities) in the high-bandgap sub-cell, which is lowered to 10$^{5}$ s$^{-1}$ in the better-bandgap-matched perovskite-silicon cells. We demonstrate luminescence coupling endows greater flexibility in both sub-cell thicknesses, increased tolerance to different spectral conditions and a reduction in the total thickness of light absorbing layers. To maximally exploit luminescence coupling we reveal a key design rule for luminescent perovskite-based tandems: the high-bandgap sub-cell should always have the higher short-circuit current. Importantly, this can be achieved by reducing the bandgap or increasing the thickness in the high-bandgap sub-cell with minimal reduction in efficiency, thus allowing for wider, unstable bandgap compositions (>1.7 eV) to be avoided. Finally, we experimentally visualise luminescence coupling in an all-perovskite tandem device stack through cross-section luminescence images.
△ Less
Submitted 1 December, 2020;
originally announced December 2020.
-
Bandgap Lowering in Mixed Alloys of Cs2Ag(SbxBi1-x)Br6 Double Perovskite Thin Films
Authors:
Zewei Li,
Sean Kavanagh,
Mari Napari,
Robert G. Palgrave,
Mojtaba Abdi-Jalebi,
Zahra Andaji-Garmaroudi,
Daniel W. Davies,
Mikko Laitinen,
Jaakko Julin,
Richard H. Friend,
David O. Scanlon,
Aron Walsh,
Robert L. Z. Hoye
Abstract:
Halide double perovskites have gained significant attention, owing to their composition of low-toxicity elements, stability in air and long charge-carrier lifetimes. However, most double perovskites, including Cs2AgBiBr6, have wide bandgaps, which limit photo conversion efficiencies. The bandgap can be reduced through hallowing with Sb3+, but Sb-rich alloys are difficult to synthesise due to the h…
▽ More
Halide double perovskites have gained significant attention, owing to their composition of low-toxicity elements, stability in air and long charge-carrier lifetimes. However, most double perovskites, including Cs2AgBiBr6, have wide bandgaps, which limit photo conversion efficiencies. The bandgap can be reduced through hallowing with Sb3+, but Sb-rich alloys are difficult to synthesise due to the high formation energy of Cs2AgSbBr6, which itself has a wide bandgap. We develop a solution-based route to synthesis phase-pure Cs2Ag(SbxBi1-x)Br6 thin films, with the mixing parameter x continuous varying over the entire composition range. We reveal that the mixed alloys (x between 0.5 and 0.9) demonstrate smaller bandgaps (as low as 2.08 eV) than the pure Sb- (2.18 eV) and Bi-based (2.25 eV) compounds, with strong deviation from Vegard's law. Through in-depth computations, we propose that bandgap lowering arises from the Type II band alignment between Cs2AgBiBr6 and Cs2AgSbBr6. The energy mismatch between the Bi and Sb s and p atomic orbitals, coupled with their non-linear mixing, results in the alloys adopting a smaller bandgap than the pure compounds. Our work demonstrates an approach to achieve bandgap reduction and highlights that bandgap bowing may be found in other double perovskite alloys by pairing together materials forming a Type II band alignment.
△ Less
Submitted 1 July, 2020;
originally announced July 2020.
-
Local Strain Heterogeneity Influences the Optoelectronic Properties of Halide Perovskites
Authors:
Timothy W. Jones,
Anna Osherov,
Mejd Alsari,
Melany Sponseller,
Benjamin C. Duck,
Young-Kwang Jung,
Charles Settens,
Farnaz Niroui,
Roberto Brenes,
Camelia V. Stan,
Yao Li,
Mojtaba Abdi-Jalebi,
Nobumichi Tamura,
J. Emyr Macdonald,
Manfred Burghammer,
Richard H. Friend,
Vladimir Bulović,
Aron Walsh,
Gregory J. Wilson,
Samuele Lilliu,
Samuel D. Stranks
Abstract:
Halide perovskites are promising semiconductors for inexpensive, high-performance optoelectronics. Despite a remarkable defect tolerance compared to conventional semiconductors, perovskite thin films still show substantial microscale heterogeneity in key properties such as luminescence efficiency and device performance. This behavior has been attributed to spatial fluctuations in the population of…
▽ More
Halide perovskites are promising semiconductors for inexpensive, high-performance optoelectronics. Despite a remarkable defect tolerance compared to conventional semiconductors, perovskite thin films still show substantial microscale heterogeneity in key properties such as luminescence efficiency and device performance. This behavior has been attributed to spatial fluctuations in the population of sub-bandgap electronic states that act as trap-mediated non-radiative recombination sites. However, the origin of the variations, trap states and extent of the defect tolerance remains a topic of debate, and a precise understanding is critical to the rational design of defect management strategies. By combining scanning X-ray diffraction beamlines at two different synchrotrons with high-resolution transmission electron microscopy, we reveal levels of heterogeneity on the ten-micrometer scale (super-grains) and even ten-nanometer scale (sub-grain domains). We find that local strain is associated with enhanced defect concentrations, and correlations between the local structure and time-resolved photoluminescence reveal that these strain-related defects are the cause of non-radiative recombination. We reveal a direct connection between defect concentrations and non-radiative losses, as well as complex heterogeneity across multiple length scales, shedding new light on the presence and influence of structural defects in halide perovskites.
△ Less
Submitted 15 May, 2018; v1 submitted 3 March, 2018;
originally announced March 2018.
-
Maximising and Stabilising Luminescence in Metal Halide Perovskite Device Structures
Authors:
Mojtaba Abdi-Jalebi,
Zahra Andaji-Garmaroudi,
Stefania Cacovich,
Camille Stavrakas,
Bertrand Philippe,
Johannes M. Richter,
Mejd Alsari,
Edward P. Booker,
Eline M. Hutter,
Andrew J. Pearson,
Samuele Lilliu,
Tom J Savenije,
Håkan Rensmo,
Giorgio Divitini,
Caterina Ducati,
Richard H. Friend,
Samuel D. Stranks
Abstract:
Metal halide perovskites are attracting tremendous interest for a variety of optoelectronic applications. The ability to tune the perovskite bandgap by tweaking the chemical compositions opens up new applications as coloured emitters and as components of tandem photovoltaics. Nevertheless, non-radiative losses are still limiting performance, with luminescence yields in state-of-the-art perovskite…
▽ More
Metal halide perovskites are attracting tremendous interest for a variety of optoelectronic applications. The ability to tune the perovskite bandgap by tweaking the chemical compositions opens up new applications as coloured emitters and as components of tandem photovoltaics. Nevertheless, non-radiative losses are still limiting performance, with luminescence yields in state-of-the-art perovskite solar cells still far from 100% under solar illumination conditions. Furthermore, in mixed halide perovskite systems designed for continuous bandgap tunability (bandgaps ~1.7-1.9 eV), photo-induced ion segregation leads to bandgap instabilities. Here, we substantially mitigate both non-radiative losses and photo-induced ion migration in perovskite structures by decorating the surfaces and grain boundaries with passivating potassium-halide interlayers. We demonstrate external photo-luminescence quantum yields of 66%, translating to internal yields exceeding 95%. The high luminescence yields are achieved while maintaining high mobilities over 40 cm2V-1s-1, giving the elusive combination of both high luminescence and excellent charge transport. We find that the external luminescence yield when interfaced with electrodes in a solar cell device stack, a quantity that must be maximized to approach the efficiency limits, remains as high as 15%, indicating very clean interfaces. We also demonstrate the inhibition of photo-induced ion migration processes across a wide range of mixed halide perovskite bandgaps that otherwise show bandgap instabilities. We validate these results in full operating solar cells, highlighting the importance of stabilising luminescence in device structures. Our work represents a critical breakthrough in the construction of tunable halide perovskite films and interfaces that can approach the efficiency limits in tandem solar cells and coloured LEDs.
△ Less
Submitted 13 December, 2017;
originally announced December 2017.
