-
The X-ray Integral Field Unit at the end of the Athena reformulation phase
Authors:
Philippe Peille,
Didier Barret,
Edoardo Cucchetti,
Vincent Albouys,
Luigi Piro,
Aurora Simionescu,
Massimo Cappi,
Elise Bellouard,
Céline Cénac-Morthé,
Christophe Daniel,
Alice Pradines,
Alexis Finoguenov,
Richard Kelley,
J. Miguel Mas-Hesse,
Stéphane Paltani,
Gregor Rauw,
Agata Rozanska,
Jiri Svoboda,
Joern Wilms,
Marc Audard,
Enrico Bozzo,
Elisa Costantini,
Mauro Dadina,
Thomas Dauser,
Anne Decourchelle
, et al. (257 additional authors not shown)
Abstract:
The Athena mission entered a redefinition phase in July 2022, driven by the imperative to reduce the mission cost at completion for the European Space Agency below an acceptable target, while maintaining the flagship nature of its science return. This notably called for a complete redesign of the X-ray Integral Field Unit (X-IFU) cryogenic architecture towards a simpler active cooling chain. Passi…
▽ More
The Athena mission entered a redefinition phase in July 2022, driven by the imperative to reduce the mission cost at completion for the European Space Agency below an acceptable target, while maintaining the flagship nature of its science return. This notably called for a complete redesign of the X-ray Integral Field Unit (X-IFU) cryogenic architecture towards a simpler active cooling chain. Passive cooling via successive radiative panels at spacecraft level is now used to provide a 50 K thermal environment to an X-IFU owned cryostat. 4.5 K cooling is achieved via a single remote active cryocooler unit, while a multi-stage Adiabatic Demagnetization Refrigerator ensures heat lift down to the 50 mK required by the detectors. Amidst these changes, the core concept of the readout chain remains robust, employing Transition Edge Sensor microcalorimeters and a SQUID-based Time-Division Multiplexing scheme. Noteworthy is the introduction of a slower pixel. This enables an increase in the multiplexing factor (from 34 to 48) without compromising the instrument energy resolution, hence keeping significant system margins to the new 4 eV resolution requirement. This allows reducing the number of channels by more than a factor two, and thus the resource demands on the system, while keeping a 4' field of view (compared to 5' before). In this article, we will give an overview of this new architecture, before detailing its anticipated performances. Finally, we will present the new X-IFU schedule, with its short term focus on demonstration activities towards a mission adoption in early 2027.
△ Less
Submitted 15 February, 2025;
originally announced February 2025.
-
The Athena X-ray Integral Field Unit: a consolidated design for the system requirement review of the preliminary definition phase
Authors:
Didier Barret,
Vincent Albouys,
Jan-Willem den Herder,
Luigi Piro,
Massimo Cappi,
Juhani Huovelin,
Richard Kelley,
J. Miguel Mas-Hesse,
Stéphane Paltani,
Gregor Rauw,
Agata Rozanska,
Jiri Svoboda,
Joern Wilms,
Noriko Yamasaki,
Marc Audard,
Simon Bandler,
Marco Barbera,
Xavier Barcons,
Enrico Bozzo,
Maria Teresa Ceballos,
Ivan Charles,
Elisa Costantini,
Thomas Dauser,
Anne Decourchelle,
Lionel Duband
, et al. (274 additional authors not shown)
Abstract:
The Athena X-ray Integral Unit (X-IFU) is the high resolution X-ray spectrometer, studied since 2015 for flying in the mid-30s on the Athena space X-ray Observatory, a versatile observatory designed to address the Hot and Energetic Universe science theme, selected in November 2013 by the Survey Science Committee. Based on a large format array of Transition Edge Sensors (TES), it aims to provide sp…
▽ More
The Athena X-ray Integral Unit (X-IFU) is the high resolution X-ray spectrometer, studied since 2015 for flying in the mid-30s on the Athena space X-ray Observatory, a versatile observatory designed to address the Hot and Energetic Universe science theme, selected in November 2013 by the Survey Science Committee. Based on a large format array of Transition Edge Sensors (TES), it aims to provide spatially resolved X-ray spectroscopy, with a spectral resolution of 2.5 eV (up to 7 keV) over an hexagonal field of view of 5 arc minutes (equivalent diameter). The X-IFU entered its System Requirement Review (SRR) in June 2022, at about the same time when ESA called for an overall X-IFU redesign (including the X-IFU cryostat and the cooling chain), due to an unanticipated cost overrun of Athena. In this paper, after illustrating the breakthrough capabilities of the X-IFU, we describe the instrument as presented at its SRR, browsing through all the subsystems and associated requirements. We then show the instrument budgets, with a particular emphasis on the anticipated budgets of some of its key performance parameters. Finally we briefly discuss on the ongoing key technology demonstration activities, the calibration and the activities foreseen in the X-IFU Instrument Science Center, and touch on communication and outreach activities, the consortium organisation, and finally on the life cycle assessment of X-IFU aiming at minimising the environmental footprint, associated with the development of the instrument. Thanks to the studies conducted so far on X-IFU, it is expected that along the design-to-cost exercise requested by ESA, the X-IFU will maintain flagship capabilities in spatially resolved high resolution X-ray spectroscopy, enabling most of the original X-IFU related scientific objectives of the Athena mission to be retained. (abridged).
△ Less
Submitted 28 November, 2022; v1 submitted 30 August, 2022;
originally announced August 2022.
-
The Aperture Array Verification System 1: System overview and early commissioning results
Authors:
P. Benthem,
R. Wayth,
E. de Lera Acedo,
K. Zarb Adami,
M. Alderighi,
C. Belli,
P. Bolli,
T. Booler,
J. Borg,
J. W. Broderick,
S. Chiarucci,
R. Chiello,
L. Ciani,
G. Comoretto,
B. Crosse,
D. Davidson,
A. DeMarco,
D. Emrich,
A. van Es,
D. Fierro,
A. Faulkner,
M. Gerbers,
N. Razavi-Ghods,
P. Hall,
L. Horsley
, et al. (29 additional authors not shown)
Abstract:
The design and development process for the Square Kilometre Array (SKA) radio telescope, the Low Frequency Aperture Array component, was progressed during the SKA pre-construction phase by an international consortium, with the goal of meeting requirements for a critical design review. As part of the development process a full-sized prototype SKA Low station was deployed, the Aperture Array Verific…
▽ More
The design and development process for the Square Kilometre Array (SKA) radio telescope, the Low Frequency Aperture Array component, was progressed during the SKA pre-construction phase by an international consortium, with the goal of meeting requirements for a critical design review. As part of the development process a full-sized prototype SKA Low station was deployed, the Aperture Array Verification System 1 (AAVS1). We provide a system overview and describe the commissioning results of AAVS1, which is a low frequency radio telescope with 256 dual-polarisation log-periodic dipole antennas working as a phased array. A detailed system description is provided, including an in-depth overview of relevant sub-systems, ranging from hardware, firmware, software, calibration,and control sub-systems. Early commissioning results cover initial bootstrapping, array calibration, stability testing, beam-forming,and on-sky sensitivity validation. Lessons learned are presented, along with future developments.
△ Less
Submitted 7 October, 2021;
originally announced October 2021.
-
SKA LFAA Station Design Report
Authors:
Eloy de Lera Acedo,
Hardie Pienaar,
Nima Razavi Ghods,
Jens Abraham,
Edgar Colin Beltran,
Ben Mort,
Fred Dulwich,
Giuseppe Virone,
Benedetta Fiorelli,
Michiel Arts,
Christophe Craeye,
Bui van Ha,
Keith Grainge,
Peter Dewdney,
Jeff Wagg,
Maria Grazia Labate,
Andrew Faulkner,
Jan Geralt bij de Vaate,
Marchel Gerbers
Abstract:
This report was submitted as part of the SKA Low Frequency Aperture Array Critical Design Review describing the design of the SKA1-LOW station that took place between 2013 and 2018.
The SKA1 LOW field station is inscribed in a circular area having an effective station diameter (centre to centre) of 38 meters and has 256 SKALA4 elements. This document describes the electromagnetic design of the f…
▽ More
This report was submitted as part of the SKA Low Frequency Aperture Array Critical Design Review describing the design of the SKA1-LOW station that took place between 2013 and 2018.
The SKA1 LOW field station is inscribed in a circular area having an effective station diameter (centre to centre) of 38 meters and has 256 SKALA4 elements. This document describes the electromagnetic design of the field station. In particular it describes the layout design and the electromagnetic modelling and characteristics of the station. This document describes the effects associated with the layout and array such as mutual coupling effects, side lobe pattern and beam shape (eg. smoothness, calibration models) and presents the state of the art of our ability to measure the array performance and validate the simulation work. The current LFAA field node requirements, derived from the SKA L1 requirements, have evolved over the last years since the LFAA PDR and the System Baseline Design. The SKA1 LOW field station has been designed to meet those requirements and has therefore tracked their evolution (eg. sensitivity requirements, array diameter, etc.). The aforementioned requirements represent a very tight space with a desire for very high sensitivity over a large frequency range (7 to 1) and wide field of view (90 degrees cone around zenith) while keeping the station diameter to a minimum, so as the filling factor but at the same time allowing for sufficient space between antennas to allow for easy maintenances, amongst many others. This results in a complex design.
△ Less
Submitted 23 April, 2020; v1 submitted 28 March, 2020;
originally announced March 2020.
-
Spacecraft Tracking Applications of the Square Kilometre Array
Authors:
J. G. Bij de Vaate,
L. I. Gurvits,
S. V. Pogrebenko,
C. G. M. van t Klooster
Abstract:
The Square Kilometre Array (SKA) is the next generation radio telescope distinguished by a superb sensitivity due to its large aperture (about one square kilometre) and advanced instrumentation. It will cover a broad range of observing bands including those used for tracking of and communications to deep space missions. While spacecraft tracking is not a main application defining the technical spe…
▽ More
The Square Kilometre Array (SKA) is the next generation radio telescope distinguished by a superb sensitivity due to its large aperture (about one square kilometre) and advanced instrumentation. It will cover a broad range of observing bands including those used for tracking of and communications to deep space missions. While spacecraft tracking is not a main application defining the technical specifications of the SKA, this facility might play a role in tracking deep space probes as a backup to the ``dedicated'' deep space tracking networks. This paper presents possible applications of the SKA as a deep space tracking facility and major related technical specifications of various concepts of the SKA. It was presented at the 3rd International Workshop on Tracking, Telemetry and Command Systems for Space Applications, ESA-ESOC, Darmstadt, Germany, 7-9 September 2004. Over the past years, the SKA concept has developed to a much higher level of detalisation and is currently at the implementation phase. A number of specific considerations in this presentation no longer correspond to the actual status of the SKA project. However, the overall concept of the SKA applications for communication and tracking of interplanetary spacecraft remain topical, and some approaches presented here remain of interest for prospective deep space missions.
△ Less
Submitted 23 February, 2020;
originally announced February 2020.
-
Spectral performance of SKA Log-periodic Antennas I: Mitigating spectral artefacts in SKA1-LOW 21-cm cosmology experiments
Authors:
Eloy de Lera Acedo,
Cathryn M. Trott,
Randall B. Wayth,
Nicolas Fagnoni,
Gianni Bernardi,
Brett Wakley,
Leon V. E. Koopmans,
Andrew J. Faulkner,
Jan Geralt bij de Vaate
Abstract:
This paper is the first in a series of papers describing the impact of antenna instrumental artefacts on the 21-cm cosmology experiments to be carried out by the low frequency instrument (SKA1-LOW) of the Square Kilometre Array telescope (SKA), i.e., the Cosmic Dawn (CD) and the Epoch of Reionization (EoR). The smoothness of the passband response of the current log-periodic antenna being developed…
▽ More
This paper is the first in a series of papers describing the impact of antenna instrumental artefacts on the 21-cm cosmology experiments to be carried out by the low frequency instrument (SKA1-LOW) of the Square Kilometre Array telescope (SKA), i.e., the Cosmic Dawn (CD) and the Epoch of Reionization (EoR). The smoothness of the passband response of the current log-periodic antenna being developed for the SKA1-LOW is analyzed using numerical electromagnetic simulations. The amplitude variations over the frequency range are characterized using low-order polynomials defined locally, in order to study the impact of the passband smoothness in the instrument calibration and CD/EoR Science. A solution is offered to correct a fast ripple found at 60~MHz during a test campaign at the SKA site at the Murchison Radio-astronomy Observatory, Western Australia in September 2015 with a minor impact on the telescope's performance and design. A comparison with the Hydrogen Epoch of Reionization Array antenna is also shown demonstrating the potential use of the SKA1-LOW antenna for the Delay Spectrum technique to detect the EoR.
△ Less
Submitted 10 April, 2017; v1 submitted 16 February, 2017;
originally announced February 2017.
-
Characterization of a Low-Frequency Radio Astronomy Prototype Array in Western Australia
Authors:
A. T. Sutinjo,
T. M. Colegate,
R. B. Wayth,
P. J. Hall,
E. de Lera Acedo,
T. Booler,
A. J. Faulkner,
L. Feng,
N. Hurley-Walker,
B. Juswardy,
S. K. Padhi,
N. Razavi-Ghods,
M. Sokolowski,
S. J. Tingay,
J. G. Bij de Vaate
Abstract:
We report characterization results for an engineering prototype of a next-generation low-frequency radio astronomy array. This prototype, which we refer to as the Aperture Array Verification System 0.5 (AAVS0.5), is a sparse pseudo-random array of 16 log-periodic antennas designed for 70-450 MHz. It is co-located with the Murchison Widefield Array (MWA) at the Murchison Radioastronomy Observatory…
▽ More
We report characterization results for an engineering prototype of a next-generation low-frequency radio astronomy array. This prototype, which we refer to as the Aperture Array Verification System 0.5 (AAVS0.5), is a sparse pseudo-random array of 16 log-periodic antennas designed for 70-450 MHz. It is co-located with the Murchison Widefield Array (MWA) at the Murchison Radioastronomy Observatory (MRO) near the Australian Square Kilometre Array (SKA) core site. We characterize the AAVS0.5 using two methods: in-situ radio interferometry with astronomical sources and an engineering approach based on detailed full-wave simulation. In-situ measurement of the small prototype array is challenging due to the dominance of the Galactic noise and the relatively weaker calibration sources easily accessible in the southern sky. The MWA, with its 128 "tiles" and up to 3 km baselines, enabled in-situ measurement via radio interferometry. We present array sensitivity and beam pattern characterization results and compare to detailed full-wave simulation. We discuss areas where differences between the two methods exist and offer possibilities for improvement. Our work demonstrates the value of the dual astronomy-simulation approach in upcoming SKA design work.
△ Less
Submitted 6 October, 2015;
originally announced October 2015.
-
Antenna array characterization via radio interferometry observation of astronomical sources
Authors:
T. M. Colegate,
A. T. Sutinjo,
P. J. Hall,
S. K. Padhi,
R. B. Wayth,
J. G. Bij de Vaate,
B. Crosse,
D. Emrich,
A. J. Faulkner,
N. Hurley-Walker,
E. de Lera Acedo,
B. Juswardy,
N. Razavi-Ghods,
S. J. Tingay,
A. Williams
Abstract:
We present an in-situ antenna characterization method and results for a "low-frequency" radio astronomy engineering prototype array, characterized over the 75-300 MHz frequency range. The presence of multiple cosmic radio sources, particularly the dominant Galactic noise, makes in-situ characterization at these frequencies challenging; however, it will be shown that high quality measurement is pos…
▽ More
We present an in-situ antenna characterization method and results for a "low-frequency" radio astronomy engineering prototype array, characterized over the 75-300 MHz frequency range. The presence of multiple cosmic radio sources, particularly the dominant Galactic noise, makes in-situ characterization at these frequencies challenging; however, it will be shown that high quality measurement is possible via radio interferometry techniques. This method is well-known in the radio astronomy community but seems less so in antenna measurement and wireless communications communities, although the measurement challenges involving multiple undesired sources in the antenna field-of-view bear some similarities. We discuss this approach and our results with the expectation that this principle may find greater application in related fields.
△ Less
Submitted 20 January, 2015;
originally announced January 2015.
-
Square Kilometre Array station configuration using two-stage beamforming
Authors:
Aziz Jiwani,
Tim Colegate,
Nima Razavi-Ghods,
Peter J Hall,
Shantanu Padhi,
Jan Geralt bij de Vaate
Abstract:
The lowest frequency band (70 - 450 MHz) of the Square Kilometre Array will consist of sparse aperture arrays grouped into geographically-localised patches, or stations. Signals from thousands of antennas in each station will be beamformed to produce station beams which form the inputs for the central correlator. Two-stage beamforming within stations can reduce SKA-low signal processing load and c…
▽ More
The lowest frequency band (70 - 450 MHz) of the Square Kilometre Array will consist of sparse aperture arrays grouped into geographically-localised patches, or stations. Signals from thousands of antennas in each station will be beamformed to produce station beams which form the inputs for the central correlator. Two-stage beamforming within stations can reduce SKA-low signal processing load and costs, but has not been previously explored for the irregular station layouts now favoured in radio astronomy arrays. This paper illustrates the effects of two-stage beamforming on sidelobes and effective area, for two representative station layouts (regular and irregular gridded tile on an irregular station). The performance is compared with a single-stage, irregular station. The inner sidelobe levels do not change significantly between layouts, but the more distant sidelobes are affected by the tile layouts; regular tile creates diffuse, but regular, grating lobes. With very sparse arrays, the station effective area is similar between layouts. At lower frequencies, the regular tile significantly reduces effective area, hence sensitivity. The effective area is highest for a two-stage irregular station, but it requires a larger station extent than the other two layouts. Although there are cost benefits for stations with two-stage beamforming, we conclude that more accurate station modelling, and SKA-low configuration specifications, are required before design finalisation.
△ Less
Submitted 20 November, 2012;
originally announced November 2012.
-
Mid-frequency aperture arrays: the future of radio astronomy
Authors:
Ilse M. van Bemmel,
Arnold van Ardenne,
Jan Geralt bij de Vaate,
Andrew J. Faulkner,
Raffaella Morganti
Abstract:
Aperture array (AA) technology is at the forefront of new developments and discoveries in radio astronomy. Currently LOFAR is successfully demonstrating the capabilities of dense and sparse AA's at low frequencies. For the mid-frequencies, from 450 to 1450MHz, AA's still have to prove their scientific value with respect to the existing dish technology. Their large field-of-view and high flexibilit…
▽ More
Aperture array (AA) technology is at the forefront of new developments and discoveries in radio astronomy. Currently LOFAR is successfully demonstrating the capabilities of dense and sparse AA's at low frequencies. For the mid-frequencies, from 450 to 1450MHz, AA's still have to prove their scientific value with respect to the existing dish technology. Their large field-of-view and high flexibility puts them in an excellent position to do so. The Aperture Array Verification Program is dedicated to demonstrate the feasibility of AA's for science in general and SKA in particular. For the mid-frequency range this has lead to the development of EMBRACE, which has already demonstrated the enormous flexibility of AA systems by observing HI and a pulsar simultaneously. It also serves as a testbed to demonstrate the technological reliability and stability of AA's. The next step will put AA technology at a level where it can be used for cutting-edge science. In this paper we discuss the developments to move AA technology from an engineering activity to a fully science capable instrument. We present current results from EMBRACE, ongoing tests of the system, and plans for EMMA, the next step in mid-frequency AA technology.
△ Less
Submitted 20 September, 2012; v1 submitted 30 August, 2012;
originally announced August 2012.
-
An Axi-Symmetric Segmented Composite SKA Dish Design: Performance and Production Analysis
Authors:
M. V. Ivashina,
R. Bakker,
J. G. bij de Vaate,
O. A. Iupikov,
M. Arts,
J. Dekker,
A. van Ardenne
Abstract:
A concept of an axi-symmetric dish as antenna reflector for the next generation radio telescope - the Square Kilometre Array (SKA) - is presented. The reflector is based on the use of novel thermoplastic composite material (reinforced with carbon fibre) in the context of the telescope design with wide band single pixel feeds. The baseline of this design represents an array of 100's to 1000's refle…
▽ More
A concept of an axi-symmetric dish as antenna reflector for the next generation radio telescope - the Square Kilometre Array (SKA) - is presented. The reflector is based on the use of novel thermoplastic composite material (reinforced with carbon fibre) in the context of the telescope design with wide band single pixel feeds. The baseline of this design represents an array of 100's to 1000's reflector antennas of 15-m diameter and covers frequencies from <1 to 10 GHz. The purpose of our study is the analysis of the production cost of the dish and its performance in combination with a realistic wideband feed (such as the 'Eleven Antenna' feed) over a wide frequency band and a range of elevation angles. The presented initial simulation results inidicate the potential of the proposed dish concept for low-cost and mass production and demonstrate sensitivity comparable to that of the presently considered off-set Gregorian reflector antenna with the same projected aperture area. We expect this observation to be independent of the choice of the feed, as several other single-pixel wideband feeds (that have been reported in the literature) have similar beamwidth and phase center location, both being rather constant with frequency.
△ Less
Submitted 27 August, 2011;
originally announced August 2011.
-
Beamforming Techniques for Large-N Aperture Arrays
Authors:
A J Faulkner,
K Zarb Adami,
J. G. Bij de Vaate,
G. W. Kant,
P. Pickard
Abstract:
Beamforming is central to the processing function of all phased arrays and becomes particularly challenging with a large number of antenna element (e.g. >100,000). The ability to beamform efficiently with reasonable power requirements is discussed in this paper. Whilst the most appropriate beamforming technology will change over time due to semiconductor and processing developments, we present a h…
▽ More
Beamforming is central to the processing function of all phased arrays and becomes particularly challenging with a large number of antenna element (e.g. >100,000). The ability to beamform efficiently with reasonable power requirements is discussed in this paper. Whilst the most appropriate beamforming technology will change over time due to semiconductor and processing developments, we present a hierarchical structure which is technology agnostic and describe both Radio-Frequency (RF) and digital hierarchical beamforming approaches. We present implementations of both RF and digital beamforming systems on two antenna array demonstrators, namely the Electronic Multi Beam Radio Astronomy ConcEpt (EMBRACE) and the dualpolarisation all-digital array (2-PAD). This paper will compare and contrast both digital and analogue implementations without considering the deep system design of these arrays.
△ Less
Submitted 24 August, 2010;
originally announced August 2010.
