Upgraded Metallurgical Grade Silicon for solar electricity production: a comparative Life Cycle Assessment
Authors:
Laura Méndez,
Eduardo Forniés,
Daniel Garrain,
Antonio Pérez Vázquez,
Alejandro Souto,
Timur Vlasenko
Abstract:
Solar grade silicon (SoG-Si) is a key material for the development of crystalline silicon photovoltaics (PV), which is expected to reach the tera-watt level in the next years and around 50TW in 2050. Upgraded metallurgical grade silicon (UMG-Si) has already demonstrated to be a viable alternative to standard polysilicon in terms of cost and quality. This study presents the life cycle assessment (L…
▽ More
Solar grade silicon (SoG-Si) is a key material for the development of crystalline silicon photovoltaics (PV), which is expected to reach the tera-watt level in the next years and around 50TW in 2050. Upgraded metallurgical grade silicon (UMG-Si) has already demonstrated to be a viable alternative to standard polysilicon in terms of cost and quality. This study presents the life cycle assessment (LCA) of UMG obtained by the FerroSolar process. Moreover, it shows the environmental impacts of PV modules and electricity generation based on this material. For this, an exhaustive review of the life cycle inventory (LCI) of PV value chain, from metallurgical grade silicon (MG-Si) down to electricity generation, has been carried out updating inputs for all processes. The Balance of System (BoS) has also been updated with real state of the art data for a fixed open ground large PV site (100 MW). Two different electricity mixes, with low and high carbon intensities, have been considered. The results reveal that for PV electricity generation using UMG instead of polysilicon leads to an overall reduction of Climate change (CC) emissions of over 20%, along with an improvement of the Energy Payback Time (EPBT) of 25%, achieving significantly low values, 12 gCO2eq / kWhe and 0.52 years, respectively. Moreover, it is shown that UMG silicon feedstock is not the main contributor to the carbon and energy footprint of the produced electricity, leaving the first place to PV module manufacturing.
△ Less
Submitted 23 February, 2021;
originally announced February 2021.
UMG silicon for solar PV: from defects detection to PV module degradation
Authors:
Eduardo Fornies,
Carlos del Canizo,
Laura Mendez,
Alejandro Souto,
Antonio Perez-Vazquez,
Daniel Garrain
Abstract:
Upgraded metallurgical grade silicon (UMG-Si) for photovoltaic (PV) solar applications has been manufactured through the metallurgical route by means of the process developed by Ferrosolar. In an ambitious mass production test, performed in commercial solar cells and modules production lines, the silicon was proven to be appropriate for photovoltaics applications (Fornies et al., 2019 Mass product…
▽ More
Upgraded metallurgical grade silicon (UMG-Si) for photovoltaic (PV) solar applications has been manufactured through the metallurgical route by means of the process developed by Ferrosolar. In an ambitious mass production test, performed in commercial solar cells and modules production lines, the silicon was proven to be appropriate for photovoltaics applications (Fornies et al., 2019 Mass production test of solar cells and modules made of 100% umg silicon. 20.76% record efficiency. Energies 12), reaching, in a conventional production line, up to 20.76% of solar cell efficiency with multicrystalline cells made of 100% UMG silicon. In this paper we present more results from the mentioned massive test. Defect engineering is being applied to improve the bulk lifetime of the UMG wafers and to guide in the identification of the limiting defects in the material. Moreover, the modules produced with 100% UMG silicon solar cells were installed together with the modules produced in the same production line with polysilicon material to assess the degradation of the UMG silicon when compared to polysilicon. After 24 months of outdoor PV generation, the degradation, in terms of Performance Ratio at 25C (25PR) diminution, has been the same for both types of modules. Additionally, a Life Cycle Assessment (LCA) has been performed for this UMG silicon and state-of-the-art Siemens polysilicon to compare the environmental impact of both silicon feedstocks. The results presented in this paper; chemical analysis of wafers, defect engineering, low degradation, average efficiency and environmental assessment, lead to a complete study of UMG silicon, confirming its potential to be used as raw material for PV applications.
△ Less
Submitted 13 April, 2021; v1 submitted 20 January, 2021;
originally announced January 2021.
