Showing 1–39 of 39 results for author: Chan, H B

Casimir-Lifshitz force for graphene-covered gratings

Authors: Youssef Jeyar, Minggang Luo, Brahim Guizal, H. B. Chan, Mauro Antezza

Abstract: We study the Casimir-Lifshitz force (CLF) between a gold plate and a graphene-covered dielectric grating. Using a scattering matrix (S-matrix) approach derived from the Fourier Modal Method (FMM), we find a significant enhancement in the CLF as compared to a mere dielectric slab coated with graphene, over a wide range of temperatures. Additionally, we demonstrate that the CLF depends strongly on t… ▽ More We study the Casimir-Lifshitz force (CLF) between a gold plate and a graphene-covered dielectric grating. Using a scattering matrix (S-matrix) approach derived from the Fourier Modal Method (FMM), we find a significant enhancement in the CLF as compared to a mere dielectric slab coated with graphene, over a wide range of temperatures. Additionally, we demonstrate that the CLF depends strongly on the chemical potential of graphene, with maximal effects observed at lower filling fractions. Finally, we analyse the Casimir force gradient between a gold sphere and a graphene-coated dielectric grating, highlighting potential avenues for experimental measurements. △ Less

Submitted 23 May, 2024; originally announced May 2024.

Comments: 11 pages, 10 figures

Journal ref: Phys. Rev. B 110, 045446 (2024)

Frequency stabilization of self-sustained oscillations in a sideband-driven electromechanical resonator

Authors: B. Zhang, Yingming Yan, X. Dong, M. I. Dykman, H. B. Chan

Abstract: We present a method to stabilize the frequency of self-sustained vibrations in micro- and nanomechanical resonators. The method refers to a two-mode system with the vibrations at significantly different frequencies. The signal from one mode is used to control the other mode. In the experiment, self-sustained oscillations of micromechanical modes are excited by pumping at the blue-detuned sideband… ▽ More We present a method to stabilize the frequency of self-sustained vibrations in micro- and nanomechanical resonators. The method refers to a two-mode system with the vibrations at significantly different frequencies. The signal from one mode is used to control the other mode. In the experiment, self-sustained oscillations of micromechanical modes are excited by pumping at the blue-detuned sideband of the higher-frequency mode. Phase fluctuations of the two modes show near perfect anti-correlation. They can be compensated in either one of the modes by a stepwise change of the pump phase. The phase change of the controlled mode is proportional to the pump phase change, with the proportionality constant independent of the pump amplitude and frequency. This finding allows us to stabilize the phase of one mode against phase diffusion using the measured phase of the other mode. We demonstrate that phase fluctuations of either the high or low frequency mode can be significantly reduced. The results open new opportunities in generating stable vibrations in a broad frequency range via parametric downconversion in nonlinear resonators. △ Less

Submitted 13 May, 2024; originally announced May 2024.

Controlled asymmetric Ising model implemented with parametric micromechanical oscillators

Authors: C. Han, M. Wang, B. Zhang, M. I. Dykman, H. B. Chan

Abstract: Asymmetric Ising model, in which coupled spins affect each other differently, plays an important role in diverse fields, from physics to biology to artificial intelligence. We show that coupled parametric oscillators provide a well-controlled and fully characterizable physical system to implement the model. Such oscillators are bistable. The coupling changes the rate of interstate switching of an… ▽ More Asymmetric Ising model, in which coupled spins affect each other differently, plays an important role in diverse fields, from physics to biology to artificial intelligence. We show that coupled parametric oscillators provide a well-controlled and fully characterizable physical system to implement the model. Such oscillators are bistable. The coupling changes the rate of interstate switching of an oscillator depending on the state of other oscillators. Our experiment on two coupled micromechanical resonators reveals unusual features of asymmetric Ising systems, including the onset of a probability current that circulates in the stationary state. We relate the asymmetry to the exponentially strong effect of a periodic force on the switching rates of an individual parametric oscillator, which we measure. Our findings open the possibilities of constructing and exploring asymmetric Ising systems with controlled parameters and connectivity. △ Less

Submitted 8 September, 2023; originally announced September 2023.

Journal ref: Phys. Rev. Reserach 6, 023162 (2024)

Tunable non-additivity in Casimir-Lifshitz force between graphene gratings

Authors: Youssef Jeyar, Minggang Luo, Kevin Austry, Brahim Guizal, Yi Zheng, H. B. Chan, Mauro Antezza

Abstract: We investigate the Casimir-Lifshitz force (CLF) between two identical graphene strip gratings, laid on finite dielectric substrates, by using the scattering matrix (S-matrix) approach derived from the Fourier Modal Method with Local Basis Functions (FMM-LBF). We fully take into account the high-order electromagnetic diffractions, the multiple scattering and the exact 2D feature of the graphene str… ▽ More We investigate the Casimir-Lifshitz force (CLF) between two identical graphene strip gratings, laid on finite dielectric substrates, by using the scattering matrix (S-matrix) approach derived from the Fourier Modal Method with Local Basis Functions (FMM-LBF). We fully take into account the high-order electromagnetic diffractions, the multiple scattering and the exact 2D feature of the graphene strips. We show that the non-additivity, which is one of the most interesting features of the CLF in general, is significantly high and can be modulated in situ, without any change in the actual material geometry and this by varying the graphene chemical potential. We discuss the nature of the geometrical effects and show the relevance of the geometric parameter d/D (i.e. the ratio between separation and grating period), which allows to explore the regions of parameters where the additive result is fully acceptable or where the full calculation is needed. This study can open to deeper experimental exploration of the non-additive features of the CLF with micro- or nano-electromechanical graphene-based systems. △ Less

Submitted 15 November, 2023; v1 submitted 30 June, 2023; originally announced June 2023.

Comments: 11 pages, 6 figures

Journal ref: Phys. Rev. A 108, 062811 (2023)

Casimir-Lifshitz force between graphene-based structures out of thermal equilibrium

Authors: Youssef Jeyar, Kevin Austry, Minggang Luo, Brahim Guizal, H. B. Chan, Mauro Antezza

Abstract: We study the non equilibrium Casimir-Lifshitz force between graphene-based parallel structures held at different temperatures and in presence of an external thermal bath at a third temperature. The graphene conductivity, which is itself a function of temperature, as well as of chemical potential, allows us to tune in situ the Casimir-Lifshitz force. We explore different non equilibrium configurati… ▽ More We study the non equilibrium Casimir-Lifshitz force between graphene-based parallel structures held at different temperatures and in presence of an external thermal bath at a third temperature. The graphene conductivity, which is itself a function of temperature, as well as of chemical potential, allows us to tune in situ the Casimir-Lifshitz force. We explore different non equilibrium configurations while considering different values of the graphene chemical potential. Particularly interesting cases are investigated, where the force can change sign going from attractive to repulsive or where the force becomes non monotonic with respect to chemical potential variations, contrary to the behaviour under thermal equilibrium. △ Less

Submitted 20 September, 2023; v1 submitted 30 May, 2023; originally announced May 2023.

Comments: 10 pages, 18 figures

Journal ref: Phys. Rev. B 108, 115412 (2023)

Superfluid $^3$He-B Surface States in a Confined Geometry Probed by a Microelectromechanical Oscillator

Authors: W. G. Jiang, C. S. Barquist, K. Gunther, Y. Lee, H. B. Chan

Abstract: A microelectromechanical oscillator with a 0.73 $μ$m gap structure is employed to probe the surface Andreev bound states in superfluid $^3$He-B. The surface specularity of the oscillator is increased by preplating it with 1.6 monolayers of $^4$He. In the linear regime, the temperature dependence of the damping coefficient is measured at various pressures, and the normalized energy gap is extracted… ▽ More A microelectromechanical oscillator with a 0.73 $μ$m gap structure is employed to probe the surface Andreev bound states in superfluid $^3$He-B. The surface specularity of the oscillator is increased by preplating it with 1.6 monolayers of $^4$He. In the linear regime, the temperature dependence of the damping coefficient is measured at various pressures, and the normalized energy gap is extracted. The damping coefficient increases after preplating at lower pressures, which is attributed to the decreased energy minigap of the surface bound states. The device is also driven into the nonlinear regime, where the temperature independent critical velocity at each pressure is measured. The critical velocity is observed to increase after preplating at all pressures, which might be related to the increased average energy gap. The observed behavior warrants a microscopic theory beyond a single parameter characterization of the surface. △ Less

Submitted 29 March, 2023; originally announced March 2023.

Comments: 10 pages, 15 figures, to be submitted to Physical Review B

Energy Transfer into Period-Tripled States in Coupled Electromechanical Modes at Internal Resonance

Authors: Yingming Yan, X. Dong, L. Huang, K. Moskovtsev, H. B. Chan

Abstract: Efficient energy transfer often occurs between oscillation modes in a resonator when they are tuned to internal resonance. We design the eigenfrequencies of two vibrational modes of an electromechanical resonator to be close to a ratio of 3:1 and demonstrate that the energy supplied to the upper mode can be controllably transferred to the lower mode. With the lower mode vibrating with a period tri… ▽ More Efficient energy transfer often occurs between oscillation modes in a resonator when they are tuned to internal resonance. We design the eigenfrequencies of two vibrational modes of an electromechanical resonator to be close to a ratio of 3:1 and demonstrate that the energy supplied to the upper mode can be controllably transferred to the lower mode. With the lower mode vibrating with a period tripled that of the upper mode, the discrete time-translation symmetry imposed by the periodic drive is broken. The lower mode settles into one of three stable period-tripled states with different phases. This channel for energy transfer from the upper mode can be turned on or off without changing system parameters. When the upper mode itself becomes multistable under strong resonant or parametric drive, additional sets of coexisting period-tripled states emerge in the lower mode. In the latter case, we measure a total of 6 coexisting vibration states with identical amplitude but phases differing by $π$/3. Excitation of coexisting states with three different phases could open new opportunities in designing mechanical memory based on ternary logic. Coupled resonators with period-tripled states can also be used to model complex interacting systems with spin equals one. △ Less

Submitted 20 September, 2022; v1 submitted 3 June, 2022; originally announced June 2022.

Journal ref: Phys. Rev. X 12, 031003 (2022)

Strong geometry dependence of the Casimir force between interpenetrated rectangular gratings

Authors: Mingkang Wang, L. Tang, C. Y. Ng, Riccardo Messina, Brahim Guizal, J. A. Crosse, Mauro Antezza, C. T. Chan, H. B. Chan

Abstract: Quantum fluctuations give rise to Casimir forces between two parallel conducting plates, the magnitude of which increases monotonically as the separation decreases. By introducing nanoscale gratings to the surfaces, recent advances have opened opportunities for controlling the Casimir force in complex geometries. Here, we measure the Casimir force between two rectangular gratings in regimes not ac… ▽ More Quantum fluctuations give rise to Casimir forces between two parallel conducting plates, the magnitude of which increases monotonically as the separation decreases. By introducing nanoscale gratings to the surfaces, recent advances have opened opportunities for controlling the Casimir force in complex geometries. Here, we measure the Casimir force between two rectangular gratings in regimes not accessible before. Using an on-chip detection platform, we achieve accurate alignment between the two gratings so that they interpenetrate as the separation is reduced. Just before interpenetration occurs, the measured Casimir force is found to have a geometry dependence that is much stronger than previous experiments, with deviations from the proximity force approximation reaching a factor of ~500. After the gratings interpenetrate each other, the Casimir force becomes non-zero and independent of displacement. This work shows that the presence of gratings can strongly modify the Casimir force to control the interaction between nanomechanical components. △ Less

Submitted 8 January, 2021; v1 submitted 4 September, 2020; originally announced September 2020.

Comments: 31 pages, 7 figures

Journal ref: Nature Communication 12, 600 (2021)

Damping of a micro-electromechanical oscillator in turbulent superfluid $^4$He: A novel probe of quantized vorticity in the ultra-low temperature regime

Authors: C. S. Barquist, W. G. Jiang, K. Gunther, N. Eng, Y. Lee, H. B. Chan

Abstract: We report a comprehensive investigation of the effects of quantum turbulence and quantized vorticity in superfluid $^4$He on the motion of a micro-electromechanical systems (MEMS) resonator. We find that the MEMS is uniquely sensitive to quantum turbulence present in the fluid. To generate turbulence in the fluid, a quartz tuning fork (TF) is placed in proximity to the MEMS and driven at large amp… ▽ More We report a comprehensive investigation of the effects of quantum turbulence and quantized vorticity in superfluid $^4$He on the motion of a micro-electromechanical systems (MEMS) resonator. We find that the MEMS is uniquely sensitive to quantum turbulence present in the fluid. To generate turbulence in the fluid, a quartz tuning fork (TF) is placed in proximity to the MEMS and driven at large amplitude. We observe that at low velocity, the MEMS is damped by the turbulence, and that above a critical velocity, $v_c \simeq 5\,$mm\,s$^{-1}$, the turbulent damping is greatly reduced. We find that above $v_c$, the damping of the MEMS is reduced further for increasing velocity, indicating a velocity dependent coupling between the surface of the MEMS and the quantized vortices constituting the turbulence. We propose a model of the interaction between vortices in the fluid and the surface of the MEMS. The sensitivity of these devices to a small number of vortices and the almost unlimited customization of MEMS open the door to a more complete understanding of the interaction between quantized vortices and oscillating structures, which in turn provides a new route for the investigation of the dynamics of single vortices. △ Less

Submitted 13 May, 2020; originally announced May 2020.

Comments: 14 pages, 10 figures

Frequency stabilization and noise-induced spectral narrowing in resonators with zero dispersion

Authors: L. Huang, S. M. Soskin, I. A. Khovanov, R. Mannella, K. Ninios, H. B. Chan

Abstract: Mechanical resonators are widely used as precision clocks and sensitive detectors that rely on the stability of their eigenfrequencies. The phase noise is determined by different factors ranging from thermal noise and frequency noise of the resonator to noise in the feedback circuitry. Increasing the vibration amplitude can mitigate some of these effects but the improvements are limited by nonline… ▽ More Mechanical resonators are widely used as precision clocks and sensitive detectors that rely on the stability of their eigenfrequencies. The phase noise is determined by different factors ranging from thermal noise and frequency noise of the resonator to noise in the feedback circuitry. Increasing the vibration amplitude can mitigate some of these effects but the improvements are limited by nonlinearities that are particularly strong for miniaturized micro- and nano-mechanical systems. Here we design a micromechanical resonator with non-monotonic dependence of the frequency of eigenoscillations on energy. Near the extremum, where the dispersion of the eigenfrequency is zero, the system regains certain characteristics of a linear resonator, albeit at large vibration amplitudes. The spectral peak undergoes counter-intuitive narrowing when the noise intensity is increased. With the resonator serving as the frequency determining element in a feedback loop, the phase noise at the extremum amplitude is three times smaller than the conventional nonlinear regime. Zero dispersion phenomena open new opportunities for improving resonant sensors and frequency references. △ Less

Submitted 5 September, 2019; v1 submitted 3 September, 2019; originally announced September 2019.

Journal ref: Nature Communications volume 10, Article number: 3930 (2019)

Giant Casimir torque between rotated gratings and the $θ=0$ anomaly

Authors: Mauro Antezza, H. B. Chan, Brahim Guizal, Valery N. Marachevsky, Riccardo Messina, M. Wang

Abstract: We study the Casimir torque between two metallic one-dimensional gratings rotated by an angle $θ$ with respect to each other. We find that, for infinitely extended gratings, the Casimir energy is anomalously discontinuous at $θ=0$, due to a critical zero-order geometric transition between a 2D- and a 1D-periodic system. This transition is a peculiarity of the grating geometry and does not exist fo… ▽ More We study the Casimir torque between two metallic one-dimensional gratings rotated by an angle $θ$ with respect to each other. We find that, for infinitely extended gratings, the Casimir energy is anomalously discontinuous at $θ=0$, due to a critical zero-order geometric transition between a 2D- and a 1D-periodic system. This transition is a peculiarity of the grating geometry and does not exist for intrinsically anisotropic materials. As a remarkable practical consequence, for finite-size gratings, the torque per area can reach extremely large values, increasing without bounds with the size of the system. We show that for finite gratings with only 10 period repetitions, the maximum torque is already 60 times larger than the one predicted in the case of infinite gratings. These findings pave the way to the design of a contactless quantum vacuum torsional spring, with possible relevance to micro- and nano-mechanical devices. △ Less

Submitted 1 April, 2019; originally announced April 2019.

Comments: 7 pages, 4 figures

Journal ref: Phys. Rev. Lett. 124, 013903 (2020)

Measurement of mechanical deformations induced by enhanced electromagnetic stress on a parallel metallic-plate system

Authors: M. Wang, S. Wang, Q. Zhang, C. T. Chan, H. B. Chan

Abstract: We measured the electromagnetic stress-induced local strain distribution on a centimeter-sized parallel-plate metallic resonant unit illuminated with microwave. Using a fiber interferometer, we found that the strain changes sign across the resonant unit, in agreement with theoretical predictions that the attractive electric and repulsive magnetic forces act at different locations. The enhancement… ▽ More We measured the electromagnetic stress-induced local strain distribution on a centimeter-sized parallel-plate metallic resonant unit illuminated with microwave. Using a fiber interferometer, we found that the strain changes sign across the resonant unit, in agreement with theoretical predictions that the attractive electric and repulsive magnetic forces act at different locations. The enhancement of the corresponding maximum local electromagnetic stress is stronger than the enhancement of the net force, reaching a factor of >600 compared to the ordinary radiation pressure. △ Less

Submitted 23 April, 2018; originally announced April 2018.

Comments: 15 pages, 5 figures

Journal ref: Phys. Rev. Lett. 121, 035502 (2018)

Strong negative nonlinear friction from induced two-phonon processes in vibrational systems

Authors: X. Dong, M. I. Dykman, H. B. Chan

Abstract: Self-sustained vibrations in systems ranging from lasers to clocks to biological systems are often associated with the coefficient of linear friction, which relates the friction force to the velocity, becoming negative [1,2]. The runaway of the vibration amplitude is prevented by positive nonlinear friction that increases rapidly with the amplitude. Here we use a modulated electromechanical resona… ▽ More Self-sustained vibrations in systems ranging from lasers to clocks to biological systems are often associated with the coefficient of linear friction, which relates the friction force to the velocity, becoming negative [1,2]. The runaway of the vibration amplitude is prevented by positive nonlinear friction that increases rapidly with the amplitude. Here we use a modulated electromechanical resonator to show that nonlinear friction can be made negative and sufficiently strong to overcome positive linear friction at large vibration amplitudes. The experiment involves applying a drive that simultaneously excites two phonons of the studied mode and a phonon of a faster decaying high-frequency mode. We study generic features of the oscillator dynamics with negative nonlinear friction. Remarkably, self-sustained vibrations of the oscillator need to be activated in this case. When, in addition, a resonant force is applied, a branch of large-amplitude forced vibrations can emerge, isolated from the branch of the ordinary small-amplitude response. Isolated branches of self-sustained and forced vibrations are advantageous for applications in sensing and control. △ Less

Submitted 3 April, 2018; originally announced April 2018.

Journal ref: Nature Communicationsvolume 9, Article number: 3241 (2018)

Measurement of non-monotonic Casimir forces between silicon nanostructures

Authors: L. Tang, M. Wang, C. Y. Ng, M. Nikolic, C. T. Chan, A. W. Rodriguez, H. B. Chan

Abstract: Casimir forces are of fundamental interest because they originate from quantum fluctuations of the electromagnetic field. Apart from controlling the Casimir force via the optical properties of the materials, a number of novel geometries have been proposed to generate repulsive and/or non-monotonic Casimir forces between bodies separated by vacuum gaps. Experimental realization of these geometries,… ▽ More Casimir forces are of fundamental interest because they originate from quantum fluctuations of the electromagnetic field. Apart from controlling the Casimir force via the optical properties of the materials, a number of novel geometries have been proposed to generate repulsive and/or non-monotonic Casimir forces between bodies separated by vacuum gaps. Experimental realization of these geometries, however, is hindered by the difficulties in alignment when the bodies are brought into close proximity. Here, using an on-chip platform with integrated force sensors and actuators, we circumvent the alignment problem and measure the Casimir force between two surfaces with nanoscale protrusions. We demonstrate that the Casimir force depends non-monotonically on the displacement. At some displacements, the Casimir force leads to an effective stiffening of the nanomechanical spring. Our findings pave the way for exploiting the Casimir force in nanomechanical systems using structures of complex and non-conventional shapes. △ Less

Submitted 9 January, 2017; originally announced January 2017.

Comments: 26 pages, 13 figures

Journal ref: Nature Photonics (2017)

Critical Velocity in the Presence of Surface Bound States in Superfluid $^3$He-B

Authors: P. Zheng, W. G. Jiang, C. S. Barquist, Y. Lee, H. B. Chan

Abstract: A microelectromechanical oscillator with a gap of 1.25 $μ$m was immersed in superfluid $^3$He-B and cooled below 250 $μ$K at various pressures. Mechanical resonances of its shear motion were measured at various levels of driving force. The oscillator enters into a nonlinear regime above a certain threshold velocity. The damping increases rapidly in the nonlinear region and eventually prevents the… ▽ More A microelectromechanical oscillator with a gap of 1.25 $μ$m was immersed in superfluid $^3$He-B and cooled below 250 $μ$K at various pressures. Mechanical resonances of its shear motion were measured at various levels of driving force. The oscillator enters into a nonlinear regime above a certain threshold velocity. The damping increases rapidly in the nonlinear region and eventually prevents the velocity of the oscillator from increasing beyond the critical velocity which is much lower than the Landau critical velocity. We propose that this peculiar nonlinear behavior stems from the escape of quasiparticles from the surface bound states into the bulk fluid. △ Less

Submitted 12 January, 2017; v1 submitted 7 October, 2016; originally announced October 2016.

Comments: 5 pages, 4 figures

Journal ref: Phys. Rev. Lett. 118, 065301 (2017)

Anomalous Damping of a Micro-electro-mechanical Oscillator in Superfluid $^3$He-B

Authors: P. Zheng, W. G. Jiang, C. S. Barquist, Y. Lee, H. B. Chan

Abstract: The mechanical resonance properties of a micro-electro-mechanical oscillator with a gap of 1.25 $μ$m was studied in superfluid $^3$He-B at various pressures. The oscillator was driven in the linear damping regime where the damping coefficient is independent of the oscillator velocity. The quality factor of the oscillator remains low ($Q\approx 80$) down to 0.1 $T_c$, 4 orders of magnitude less tha… ▽ More The mechanical resonance properties of a micro-electro-mechanical oscillator with a gap of 1.25 $μ$m was studied in superfluid $^3$He-B at various pressures. The oscillator was driven in the linear damping regime where the damping coefficient is independent of the oscillator velocity. The quality factor of the oscillator remains low ($Q\approx 80$) down to 0.1 $T_c$, 4 orders of magnitude less than the intrinsic quality factor measured in vacuum at 4 K. In addition to the Boltzmann temperature dependent contribution to the damping, a damping proportional to temperature was found to dominate at low temperatures. We propose a multiple scattering mechanism of the surface Andreev bound states to be a possible cause for the anomalous damping. △ Less

Submitted 6 October, 2016; v1 submitted 14 June, 2016; originally announced June 2016.

Comments: 5 pages, 5 figures

Journal ref: Phys. Rev. Lett. 117, 195301 (2016)

Temperature Dependence of Viscosity in Normal Fluid $^3$He Below 800mK Determined by a Micro-electro-mechanical Oscillator

Authors: M. Gonzalez, W. G. Jiang, P. Zheng, C. S. Barquist, H. B. Chan, Y. Lee

Abstract: A micro-electro-mechanical system vibrating in its shear mode was used to study the viscosity of normal liquid $^3$He from 20mK to 770mK at 3bar, 21bar, and 29bar. The damping coefficient of the oscillator was determined by frequency sweeps through its resonance at each temperature. Using a slide film damping model, the viscosity of the fluid was obtained. Our viscosity values are compared with pr… ▽ More A micro-electro-mechanical system vibrating in its shear mode was used to study the viscosity of normal liquid $^3$He from 20mK to 770mK at 3bar, 21bar, and 29bar. The damping coefficient of the oscillator was determined by frequency sweeps through its resonance at each temperature. Using a slide film damping model, the viscosity of the fluid was obtained. Our viscosity values are compared with previous measurements and with calculated values from Fermi liquid theory. The crossover from the classical to the Fermi liquid regime is manifest in the temperature dependence of viscosity. In the Fermi liquid regime, the temperature dependence of viscosity changes from $T^{-1}$ to $T^{-2}$ on cooling, indicating a transition from the Stokes flow to the Couette flow regime. △ Less

Submitted 28 April, 2016; originally announced April 2016.

Comments: The following article has been submitted for publication to Physical Review B

Journal ref: Phys. Rev. B 94, 014505 (2016)

Correlated anomalous phase diffusion of coupled phononic modes in a side-band driven resonator

Authors: F. Sun, X. Dong, J. Zou, M. I. Dykman, H. B. Chan

Abstract: The dynamical backaction from a periodically driven optical or microwave cavity can reduce the damping of a mechanical resonator, leading to parametric instability accompanied by self-sustained oscillations. Fundamentally, the driving breaks the continuous time-translation symmetry and replaces it with the symmetry with respect to time translation by the driving period. This discrete symmetry shou… ▽ More The dynamical backaction from a periodically driven optical or microwave cavity can reduce the damping of a mechanical resonator, leading to parametric instability accompanied by self-sustained oscillations. Fundamentally, the driving breaks the continuous time-translation symmetry and replaces it with the symmetry with respect to time translation by the driving period. This discrete symmetry should be reflected in the character of the oscillations. Here, we perform experimental and theoretical study of new aspects of the backaction and the discrete time-translation symmetry using a micromechanical resonator designed to have two nonlinearly coupled vibrational modes with strongly differing frequencies and decay rates. We find that self-sustained oscillations are induced not only in the low frequency mode as measured in previous experiments, but also in the high frequency mode. The vibration frequencies and amplitudes are determined by the system nonlinearity, which also leads to bistability and hysteresis. A remarkable consequence of the discrete time-translation symmetry is revealed by studying the vibration phases. We find that the phase fluctuations of the two modes are nearly perfectly anti-correlated. At the same time, in each mode the phase undergoes anomalous diffusion, where the time dependence of the phase variance follows a superlinear rather than the standard linear power law. Our analysis shows that the exponent of the power law is determined by the exponent of the 1/f-type intrinsic frequency noise of the resonator. We demonstrate the possibility of compensating for these fluctuations using a feedback scheme to generate stable oscillations that could prove useful in frequency standards and resonant detection. △ Less

Submitted 20 July, 2016; v1 submitted 31 March, 2016; originally announced March 2016.

Comments: 27 pages, 4 figures

Journal ref: Nature Comm. 7, 12694 (2016)

Telegraph frequency noise in electromechanical resonators

Authors: Fengpei Sun, Jie Zou, Zakhar A. Maizelis, Ho Bun Chan

Abstract: We demonstrate experimentally the possibility of revealing fluctuations in the eigenfrequency of a resonator when the frequency noise is of the telegraph type. Using a resonantly driven micromechanical resonator, we show that the time-averaged vibration amplitude spectrum exhibits two peaks. They merge with an increasing rate of frequency switching and the spectrum displays an analog of motional n… ▽ More We demonstrate experimentally the possibility of revealing fluctuations in the eigenfrequency of a resonator when the frequency noise is of the telegraph type. Using a resonantly driven micromechanical resonator, we show that the time-averaged vibration amplitude spectrum exhibits two peaks. They merge with an increasing rate of frequency switching and the spectrum displays an analog of motional narrowing. We also show that the moments of the complex amplitude depend strongly on the frequency noise characteristics. This dependence remains valid even when strong thermal or detector noise is present. △ Less

Submitted 3 November, 2015; originally announced November 2015.

Comments: 14 pages, 4 figures

Journal ref: Physical Review B 91, 174102 (2015)

Work fluctuations in a nonlinear micromechanical oscillator driven far from thermal equilibrium

Authors: P. Zhou, X. Dong, C. Stambaugh, H. B. Chan

Abstract: We explore fluctuation relations in a periodically driven micromechanical torsional oscillator. In the linear regime where the modulation is weak, we verify that the ratio of the work variance to the mean work is constant, consistent with conventional fluctuation theorems. We then increase the amplitude of the periodic drive so that the response becomes nonlinear and two nonequilibrium oscillation… ▽ More We explore fluctuation relations in a periodically driven micromechanical torsional oscillator. In the linear regime where the modulation is weak, we verify that the ratio of the work variance to the mean work is constant, consistent with conventional fluctuation theorems. We then increase the amplitude of the periodic drive so that the response becomes nonlinear and two nonequilibrium oscillation states coexist. Due to interstate transitions, the work variance exhibits a peak at the driving frequency at which the occupation of the two states is equal. Moreover, the work fluctuations depend exponentially on the inverse noise intensity. Our data are consistent with recent theories on systems driven into bistability that predict generic behaviors different from conventional fluctuation theorems. △ Less

Submitted 22 October, 2015; originally announced October 2015.

Comments: To appear in Phys.Rev.E

Journal ref: Physical Review E 91, 052110 (2015)

Thermal Casimir force between nanostructured surfaces

Authors: R. Guérout, J. Lussange, H. B. Chan, A. Lambrecht, S. Reynaud

Abstract: We present detailed calculations for the Casimir force between a plane and a nanostructured surface at finite temperature in the framework of the scattering theory. We then study numerically the effect of finite temperature as a function of the grating parameters and the separation distance. We also infer non-trivial geometrical effects on the Casimir interaction via a comparison with the proximit… ▽ More We present detailed calculations for the Casimir force between a plane and a nanostructured surface at finite temperature in the framework of the scattering theory. We then study numerically the effect of finite temperature as a function of the grating parameters and the separation distance. We also infer non-trivial geometrical effects on the Casimir interaction via a comparison with the proximity force approximation. Finally, we compare our calculations with data from experiments performed with nanostructured surfaces. △ Less

Submitted 21 December, 2012; originally announced December 2012.

Journal ref: Phys. Rev. A 87, 052514 (2013)

Comb-drive MEMS Oscillators for Low Temperature Experiments

Authors: M. Gonzalez, P. Zheng, E. Garcell, Y. Lee, H. B. Chan

Abstract: We have designed and characterized micro-electro-mechanical systems (MEMS) for applications at low temperatures. The mechanical resonators were fabricated using a surface micromachining process. The devices consist of a pair of parallel plates with a well defined gap. The top plate can be actuated for shear motion relative to the bottom fixed plate through a set of comb-drive electrodes. Details o… ▽ More We have designed and characterized micro-electro-mechanical systems (MEMS) for applications at low temperatures. The mechanical resonators were fabricated using a surface micromachining process. The devices consist of a pair of parallel plates with a well defined gap. The top plate can be actuated for shear motion relative to the bottom fixed plate through a set of comb-drive electrodes. Details on the operation and fabrication of the devices are discussed. The geometry was chosen to study the transport properties of the fluid entrained in the gap. An atomic force microscopy (AFM) study was performed in order to characterize the surface. A full characterization of their resonance properties in air and at room temperature was conducted as a function of pressure, from 10 mTorr to 760 Torr, ranging from a highly rarefied gas to a hydrodynamic regime. We demonstrate the operation of our resonator at low temperatures immersed in superfluid 4He and in the normal and superfluid states of 3He down to 0.3 mK. These MEMS oscillators show potential for use in a wide range of low temperature experiments, in particular, to probe novel phenomena in quantum fluids. △ Less

Submitted 23 January, 2013; v1 submitted 4 September, 2012; originally announced September 2012.

Comments: The following article has been accepted for publication at Review of Scientific Instruments. After it is published, it will be found at: http://rsi.aip.org

Casimir forces on a silicon micromechanical chip

Authors: J. Zou, Z. Marcet, A. W. Rodriguez, M. T. H. Reid, A. P. McCauley, I. I. Kravchenko, T. Lu, Y. Bao, S. G. Johnson, H. B. Chan

Abstract: Quantum fluctuations give rise to van der Waals and Casimir forces that dominate the interaction between electrically neutral objects at sub-micron separations. Under the trend of miniaturization, such quantum electrodynamical effects are expected to play an important role in micro- and nano-mechanical devices. Nevertheless, utilization of Casimir forces on the chip level remains a major challenge… ▽ More Quantum fluctuations give rise to van der Waals and Casimir forces that dominate the interaction between electrically neutral objects at sub-micron separations. Under the trend of miniaturization, such quantum electrodynamical effects are expected to play an important role in micro- and nano-mechanical devices. Nevertheless, utilization of Casimir forces on the chip level remains a major challenge because all experiments so far require an external object to be manually positioned close to the mechanical element. Here, by integrating a force-sensing micromechanical beam and an electrostatic actuator on a single chip, we demonstrate the Casimir effect between two micromachined silicon components on the same substrate. A high degree of parallelism between the two near-planar interacting surfaces can be achieved because they are defined in a single lithographic step. Apart from providing a compact platform for Casimir force measurements, this scheme also opens the possibility of tailoring the Casimir force using lithographically defined components of non-conventional shapes. △ Less

Submitted 17 May, 2013; v1 submitted 25 July, 2012; originally announced July 2012.

Journal ref: Nature Communications 4, 1845 (2013)

Wilson ratio of a Tomonaga-Luttinger liquid in a spin-1/2 Heisenberg ladder

Authors: K. Ninios, Tao Hong, T. Manabe, C. Hotta, S. N. Herringer, M. M. Turnbull, C. P. Landee, Y. Takano, H. B. Chan

Abstract: Using micromechanical force magnetometry, we have measured the magnetization of the strong-leg spin-1/2 ladder compound (C$_7$H$_{10}$N)$_2$CuBr$_2$ at temperatures down to 45 mK. Low-temperature magnetic susceptibility as a function of field exhibits a maximum near the critical field H_c at which the magnon gap vanishes, as expected for a gapped one-dimensional antiferromagnet. Above H_c a clear… ▽ More Using micromechanical force magnetometry, we have measured the magnetization of the strong-leg spin-1/2 ladder compound (C$_7$H$_{10}$N)$_2$CuBr$_2$ at temperatures down to 45 mK. Low-temperature magnetic susceptibility as a function of field exhibits a maximum near the critical field H_c at which the magnon gap vanishes, as expected for a gapped one-dimensional antiferromagnet. Above H_c a clear minimum appears in the magnetization as a function of temperature as predicted by theory. In this field region, the susceptibility in conjunction with our specific heat data yields the Wilson ratio R_W. The result supports the relation R_W=4K, where K is the Tomonaga-Luttinger-liquid parameter. △ Less

Submitted 18 March, 2012; v1 submitted 25 October, 2011; originally announced October 2011.

Journal ref: Phys. Rev. Lett. 108, 097201 (2012)

{Rearrangement of the antiferromagnetic ordering at high magnetic fields in SmFeAsO and SmFeAsO$_{0.9}$F$_{0.1}$ single crystals

Authors: S. Weyeneth, P. J. W. Moll, R. Puzniak, K. Ninios, F. F. Balakirev, R. D. McDonald, H. B. Chan, N. D. Zhigadlo, S. Katrych, Z. Bukowski, J. Karpinski, H. Keller, B. Batlogg, L. Balicas

Abstract: The low-temperature antiferromagnetic state of the Sm-ions in both nonsuperconducting SmFeAsO and superconducting SmFeAsO$_{0.9}$F$_{0.1}$ single crystals was studied by magnetic torque, magnetization, and magnetoresistance measurements in magnetic fields up to 60~T and temperatures down to 0.6~K. We uncover in both compounds a distinct rearrangement of the antiferromagnetically ordered Sm-moments… ▽ More The low-temperature antiferromagnetic state of the Sm-ions in both nonsuperconducting SmFeAsO and superconducting SmFeAsO$_{0.9}$F$_{0.1}$ single crystals was studied by magnetic torque, magnetization, and magnetoresistance measurements in magnetic fields up to 60~T and temperatures down to 0.6~K. We uncover in both compounds a distinct rearrangement of the antiferromagnetically ordered Sm-moments near $35-40$~T. This is seen in both, static and pulsed magnetic fields, as a sharp change in the sign of the magnetic torque, which is sensitive to the magnetic anisotropy and hence to the magnetic moment in the $ab$-plane, ({\it i.e.} the FeAs-layers), and as a jump in the magnetization for magnetic fields perpendicular to the conducting planes. This rearrangement of magnetic ordering in $35-40$~T is essentially temperature independent and points towards a canted or a partially polarized magnetic state in high magnetic fields. However, the observed value for the saturation moment above this rearrangement, suggests that the complete suppression of the antiferromagnetism related to the Sm-moments would require fields in excess of 60~T. Such a large field value is particularly remarkable when compared to the relatively small Néel temperature $T_{\rm N}\simeq5$~K, suggesting very anisotropic magnetic exchange couplings. At the transition, magnetoresistivity measurements show a crossover from positive to negative field-dependence, indicating that the charge carriers in the FeAs planes are sensitive to the magnetic configuration of the rare-earth elements. This is indicates a finite magnetic/electronic coupling between the SmO and the FeAs layers which are likely to mediate the exchange interactions leading to the long range antiferromagnetic order of the Sm ions. △ Less

Submitted 16 February, 2011; originally announced February 2011.

Comments: 10 pages, 7 figures, accepted in Phys. Rev. B

Journal ref: Phys. Rev. B, 83, 134503 (2011)

Poisson noise induced switching in driven micromechanical resonators

Authors: Jie Zou, Sanal Buvaev, Mark Dykman, Ho Bun Chan

Abstract: We study Poisson-noise induced switching between coexisting vibrational states in driven nonlinear micromechanical resonators. In contrast to Gaussian noise induced switching, the measured logarithm of the switching rate is proportional not to the reciprocal noise intensity, but to its logarithm, for fixed pulse area. We also find that the switching rate logarithm varies as a square root of the di… ▽ More We study Poisson-noise induced switching between coexisting vibrational states in driven nonlinear micromechanical resonators. In contrast to Gaussian noise induced switching, the measured logarithm of the switching rate is proportional not to the reciprocal noise intensity, but to its logarithm, for fixed pulse area. We also find that the switching rate logarithm varies as a square root of the distance to the bifurcation point, instead of the conventional scaling with exponent 3/2. △ Less

Submitted 6 September, 2012; v1 submitted 6 February, 2011; originally announced February 2011.

Comments: accepted by PRB

Journal ref: Phys. Rev. B 86, 155420 (2012)

The Casimir force on a surface with shallow nanoscale corrugations: Geometry and finite conductivity effects

Authors: Y. Bao, R. Guérout, J. Lussange, A. Lambrecht, R. A. Cirelli, F. Klemens, W. M. Mansfield, C. S. Pai, H. B. Chan

Abstract: We measure the Casimir force between a gold sphere and a silicon plate with nanoscale, rectangular corrugations with depth comparable to the separation between the surfaces. In the proximity force approximation (PFA), both the top and bottom surfaces of the corrugations contribute to the force, leading to a distance dependence that is distinct from a flat surface. The measured Casimir force is fou… ▽ More We measure the Casimir force between a gold sphere and a silicon plate with nanoscale, rectangular corrugations with depth comparable to the separation between the surfaces. In the proximity force approximation (PFA), both the top and bottom surfaces of the corrugations contribute to the force, leading to a distance dependence that is distinct from a flat surface. The measured Casimir force is found to deviate from the PFA by up to 15%, in good agreement with calculations based on scattering theory that includes both geometry effects and the optical properties of the material. △ Less

Submitted 17 September, 2010; originally announced September 2010.

Journal ref: Phys.Rev.Lett.105:250402,2010

Bose-Einstein Condensation of Triplons in Ba3Cr2O8

Authors: A. A. Aczel, Y. Kohama, M. Jaime, L. Balicas, K. Ninios, H. B. Chan, H. A. Dabkowska, G. M. Luke

Abstract: By performing heat capacity, magnetocaloric effect, torque magnetometry and force magnetometry measurements up to 33 T, we have mapped out the T-H phase diagram of the S = 1/2 spin dimer compound Ba3Cr2O8. We found evidence for field-induced magnetic order between Hc1 = 12.52(2) T and Hc2 = 23.65(5) T, with the maximum transition temperature Tc = 2.7 K at H = 18 T. The lower transition can likel… ▽ More By performing heat capacity, magnetocaloric effect, torque magnetometry and force magnetometry measurements up to 33 T, we have mapped out the T-H phase diagram of the S = 1/2 spin dimer compound Ba3Cr2O8. We found evidence for field-induced magnetic order between Hc1 = 12.52(2) T and Hc2 = 23.65(5) T, with the maximum transition temperature Tc = 2.7 K at H = 18 T. The lower transition can likely be described by Bose-Einstein condensation of triplons theory, and this is consistent with the absence of any magnetization plateaus in our magnetic torque and force measurements. In contrast, the nature of the upper phase transition appears to be quite different as our measurements suggest that this transition is actually first order. △ Less

Submitted 9 March, 2009; v1 submitted 12 January, 2009; originally announced January 2009.

Comments: 4 pages, 4 figures, Accepted by PRB

Journal ref: Phys. Rev. B 79, 100409 (2009)

Switching path distribution in multi-dimensional systems

Authors: H. B. Chan, M. I. Dykman, C. Stambaugh

Abstract: We explore the distribution of paths followed in fluctuation-induced switching between coexisting stable states. We introduce a quantitative characteristic of the path distribution in phase space that does not require a priori knowledge of system dynamics. The theory of the distribution is developed and its direct measurement is performed in a micromechanical oscillator driven into parametric re… ▽ More We explore the distribution of paths followed in fluctuation-induced switching between coexisting stable states. We introduce a quantitative characteristic of the path distribution in phase space that does not require a priori knowledge of system dynamics. The theory of the distribution is developed and its direct measurement is performed in a micromechanical oscillator driven into parametric resonance. The experimental and theoretical results on the shape and position of the distribution are in excellent agreement, with no adjustable parameters. In addition, the experiment provides the first demonstration of the lack of time-reversal symmetry in switching of systems far from thermal equilibrium. The results open the possibility of efficient control of the switching probability based on the measured narrow path distribution. △ Less

Submitted 20 September, 2008; originally announced September 2008.

Comments: To appear in Phys. Rev. E

Measurement of the Casimir force between a gold sphere and silicon surface with nanoscale trench arrays

Authors: H. B. Chan, Y. Bao, J. Zou, R. A. Cirelli, F. Klemens, W. M. Mansfield, C. S. Pai

Abstract: We report measurements of the Casimir force between a gold sphere and a silicon surface with an array of nanoscale, rectangular corrugations using a micromechanical torsional oscillator. At distance between 150 nm and 500 nm, the measured force shows significant deviations from the pairwise additive formulism, demonstrating the strong dependence of the Casimir force on the shape of the interacti… ▽ More We report measurements of the Casimir force between a gold sphere and a silicon surface with an array of nanoscale, rectangular corrugations using a micromechanical torsional oscillator. At distance between 150 nm and 500 nm, the measured force shows significant deviations from the pairwise additive formulism, demonstrating the strong dependence of the Casimir force on the shape of the interacting bodies. The observed deviation, however, is smaller than the calculated values for perfectly conducting surfaces, possibly due to the interplay between finite conductivity and geometry effects. △ Less

Submitted 24 May, 2008; originally announced May 2008.

Comments: 5 pages, 3 figures

Journal ref: Phys. Rev. Lett. 101, 030401 (2008)

Paths of fluctuation induced switching

Authors: H. B. Chan, M. I. Dykman, C. Stambaugh

Abstract: We demonstrate that the paths followed by a system in fluctuation-activated switching form a narrow tube in phase space. A theory of the path distribution is developed and its direct measurement is performed in a micromechanical oscillator. The experimental and theoretical results are in excellent agreement, with no adjustable parameters. We also demonstrate the lack of time-reversal symmetry in… ▽ More We demonstrate that the paths followed by a system in fluctuation-activated switching form a narrow tube in phase space. A theory of the path distribution is developed and its direct measurement is performed in a micromechanical oscillator. The experimental and theoretical results are in excellent agreement, with no adjustable parameters. We also demonstrate the lack of time-reversal symmetry in switching of systems far from thermal equilibrium. △ Less

Submitted 24 February, 2008; originally announced February 2008.

Comments: Accepted to Phys. Rev. Lett

Activation barrier scaling and crossover for noise-induced switching in a micromechanical parametric oscillator

Authors: H. B. Chan, C. Stambaugh

Abstract: We explore fluctuation-induced switching in a parametrically-driven micromechanical torsional oscillator. The oscillator possesses one, two or three stable attractors depending on the modulation frequency. Noise induces transitions between the coexisting attractors. Near the bifurcation points, the activation barriers are found to have a power law dependence on frequency detuning with critical e… ▽ More We explore fluctuation-induced switching in a parametrically-driven micromechanical torsional oscillator. The oscillator possesses one, two or three stable attractors depending on the modulation frequency. Noise induces transitions between the coexisting attractors. Near the bifurcation points, the activation barriers are found to have a power law dependence on frequency detuning with critical exponents that are in agreement with predicted universal scaling relationships. At large detuning, we observe a crossover to a different power law dependence with an exponent that is device specific. △ Less

Submitted 15 September, 2006; originally announced September 2006.

Comments: 5 pages, 5 figures

Fluctuation-enhanced frequency mixing in a nonlinear micromechanical oscillator

Authors: H. B. Chan, C. Stambaugh

Abstract: We study noise-enhanced frequency mixing in an underdamped micromechanical torsional oscillator. The oscillator is electrostatically driven into bistability by a strong, periodic voltage at frequency $ω_d$. A second, weak ac voltage is applied at a frequency $ω$ close to $ω_d$. Due to nonlinearity in the system, vibrations occur at both $ω$ and $2ω_d-ω$. White noise is injected into the excitati… ▽ More We study noise-enhanced frequency mixing in an underdamped micromechanical torsional oscillator. The oscillator is electrostatically driven into bistability by a strong, periodic voltage at frequency $ω_d$. A second, weak ac voltage is applied at a frequency $ω$ close to $ω_d$. Due to nonlinearity in the system, vibrations occur at both $ω$ and $2ω_d-ω$. White noise is injected into the excitation, allowing the system to occasionally overcome the activation barrier and switch between the two states. At the primary drive frequency where the occupations of the two states are approximately equal, we observe noise-induced enhancement of the oscillation amplitudes at both $ω$ and the down-converted frequency $2ω_d-ω$, in agreement with theoretical predictions. Such enhancement occurs as a result of the noise-induced interstate transitions becoming synchronous with the beating between the two driving frequencies. △ Less

Submitted 1 March, 2006; originally announced March 2006.

Comments: 4 pages 5 figures

Journal ref: Phys. Rev. B 73, 224301 (2006)

Supernarrow spectral peaks near a kinetic phase transition in a driven, nonlinear micromechanical oscillator

Authors: C. Stambaugh, H. B. Chan

Abstract: We measure the spectral densities of fluctuations of an underdamped nonlinear micromechanical oscillator. By applying a sufficiently large periodic excitation, two stable dynamical states are obtained within a particular range of driving frequency. White noise is injected into the excitation, allowing the system to overcome the activation barrier and switch between the two states. While the osci… ▽ More We measure the spectral densities of fluctuations of an underdamped nonlinear micromechanical oscillator. By applying a sufficiently large periodic excitation, two stable dynamical states are obtained within a particular range of driving frequency. White noise is injected into the excitation, allowing the system to overcome the activation barrier and switch between the two states. While the oscillator predominately resides in one of the two states for most excitation frequencies, a narrow range of frequencies exist where the occupations of the two states are approximately equal. At these frequencies, the oscillator undergoes a kinetic phase transition that resembles the phase transition of thermal equilibrium systems. We observe a supernarrow peak in the power spectral densities of fluctuations of the oscillator. This peak is centered at the excitation frequency and arises as a result of noise-induced transitions between the two dynamical states. △ Less

Submitted 26 September, 2005; originally announced September 2005.

Comments: 4 pages, 4 figures

Journal ref: Phys. Rev. Lett. 97, 110602 (2006)

Noise activated switching in a driven, nonlinear micromechanical oscillator

Authors: C. Stambaugh, H. B. Chan

Abstract: We study noise induced switching in systems far from equilibrium by using an underdamped micromechanical torsional oscillator driven into the nonlinear regime. Within a certain range of driving frequencies, the oscillator possesses two stable dynamical states with different oscillation amplitudes. We induce the oscillator to escape from one dynamical state into the other by introducing noise in… ▽ More We study noise induced switching in systems far from equilibrium by using an underdamped micromechanical torsional oscillator driven into the nonlinear regime. Within a certain range of driving frequencies, the oscillator possesses two stable dynamical states with different oscillation amplitudes. We induce the oscillator to escape from one dynamical state into the other by introducing noise in the excitation. By measuring the rate of random transitions as a function of noise intensity, we deduce the activation energy as a function of frequency detuning. Close to the critical point, the activation energy is expected to display system-independent scaling. The measured critical exponent is in good agreement with variational calculations and asymptotic scaling theory. △ Less

Submitted 26 September, 2005; v1 submitted 29 April, 2005; originally announced April 2005.

Comments: 4 pages, 4 figures Changes: In Figure 1b we have added an arrow to point out where the bifurcation frequency is located. We modified the 3rd last paragraph. We corrected the citation for J. S. Aldridge and A. N. Cleland. We added a citation for Badzey et. al. We have rewritten the first and last paragraphs. We have corrected two typos: the alpha term in Eq. (5) and the definition of kappa in paragraph 5

Journal ref: Phys. Rev. B 73, 172302 (2006)

Constraining New Forces in the Casimir Regime Using the Isoelectronic Technique

Authors: R. S. Decca, D. Lopez, H. B. Chan, E. Fischbach, D. E. Krause, C. Jamell

Abstract: We report the first isoelectronic differential force measurements between a Au-coated probe and two Au-coated films, made out of Au and Ge. These measurements, performed at submicron separations using soft microelectromechanical torsional oscillators, eliminate the need for a detailed understanding of the probe-film Casimir interaction. The observed differential signal is directly converted into… ▽ More We report the first isoelectronic differential force measurements between a Au-coated probe and two Au-coated films, made out of Au and Ge. These measurements, performed at submicron separations using soft microelectromechanical torsional oscillators, eliminate the need for a detailed understanding of the probe-film Casimir interaction. The observed differential signal is directly converted into limits on the parameters $α$ and $λ$ which characterize Yukawa-like deviations from Newtonian gravity. We find $α\lsim 10^{12}$ for $λ\sim 200$ nm, an improvement of $\sim$ 10 over previous limits. △ Less

Submitted 2 February, 2005; originally announced February 2005.

Comments: 10 pages, 4 figures

Journal ref: Phys.Rev.Lett. 94 (2005) 240401

Nonlinear Micromechanical Casimir Oscillator

Authors: H. B. Chan, V. A. Aksyuk, R. N. Kleiman, D. J. Bishop, Federico Capasso

Abstract: The Casimir force between uncharged metallic surfaces originates from quantum mechanical zero point fluctuations of the electromagnetic field. We demonstrate that this quantum electrodynamical effect has a profound influence on the oscillatory behavior of microstructures when surfaces are in close proximity (<= 100 nm). Frequency shifts, hysteretic behavior and bistability caused by the Casimir… ▽ More The Casimir force between uncharged metallic surfaces originates from quantum mechanical zero point fluctuations of the electromagnetic field. We demonstrate that this quantum electrodynamical effect has a profound influence on the oscillatory behavior of microstructures when surfaces are in close proximity (<= 100 nm). Frequency shifts, hysteretic behavior and bistability caused by the Casimir force are observed in the frequency response of a periodically driven micromachined torsional oscillator. △ Less

Submitted 20 September, 2001; v1 submitted 10 September, 2001; originally announced September 2001.

Comments: 4 pages, 4 figures; added and rearranged references; added comments on sensitivity

Journal ref: Phys. Rev. Lett. 87, 211801 (2001).

Tunneling into Ferromagnetic Quantum Hall States: Observation of a Spin Bottleneck

Authors: H. B. Chan, R. C. Ashoori, L. N. Pfeiffer, K. W. West

Abstract: We explore the characteristics of equilibrium tunneling of electrons from a 3D electrode into a high mobility 2D electron system. For most 2D Landau level filling factors, we find that tunneling can be characterized by a single, well-defined tunneling rate. However, for spin-polarized quantum Hall states (nu = 1, 3 and 1/3) tunneling occurs at two distinct rates that differ by up to 2 orders of… ▽ More We explore the characteristics of equilibrium tunneling of electrons from a 3D electrode into a high mobility 2D electron system. For most 2D Landau level filling factors, we find that tunneling can be characterized by a single, well-defined tunneling rate. However, for spin-polarized quantum Hall states (nu = 1, 3 and 1/3) tunneling occurs at two distinct rates that differ by up to 2 orders of magnitude. The dependence of the two rates on temperature and tunnel barrier thickness suggests that slow in-plane spin relaxation creates a bottleneck for tunneling of electrons. △ Less

Submitted 26 May, 1999; originally announced May 1999.

Comments: 5 pages, 4 figures, submitted to PRL

Journal ref: Phys. Rev. Lett. 83 (1999) 3258

Universal Linear Density of States for Tunneling into the Two-Dimensional Electron Gas in a Magnetic field

Authors: H. B. Chan, P. I. Glicofridis, R. C. Ashoori, M. L. Melloch

Abstract: A new technique permits high fidelity measurement of the tunneling density of states (TDOS) of the two-dimensional electron gas. The obtained TDOS contains no distortions arising from low 2D in-plane conductivity and includes the contribution from localized tunneling sites. In a perpendicular magnetic field, a pseudogap develops in the TDOS at the Fermi level. Improved sensitivity enables resolu… ▽ More A new technique permits high fidelity measurement of the tunneling density of states (TDOS) of the two-dimensional electron gas. The obtained TDOS contains no distortions arising from low 2D in-plane conductivity and includes the contribution from localized tunneling sites. In a perpendicular magnetic field, a pseudogap develops in the TDOS at the Fermi level. Improved sensitivity enables resolution of a linear dependence of the TDOS on energy near the Fermi energy. The slopes of this linear gap are strongly field dependent. The data are suggestive of a new model of the gap at low energies. △ Less

Submitted 11 February, 1997; originally announced February 1997.

Comments: 5 pages, 4 postscript figures, LateX, submitted to PRL

Journal ref: Phys.Rev.Lett.79:2867,1997