-
The Analytical Method algorithm for trigger primitives generation at the LHC Drift Tubes detector
Authors:
G. Abbiendi,
J. Alcaraz Maestre,
A. Álvarez Fernández,
B. Álvarez González,
N. Amapane,
I. Bachiller,
L. Barcellan,
C. Baldanza,
C. Battilana,
M. Bellato,
G. Bencze,
M. Benettoni,
N. Beni,
A. Benvenuti,
A. Bergnoli,
L. C. Blanco Ramos,
L. Borgonovi,
A. Bragagnolo,
V. Cafaro,
A. Calderon,
E. Calvo,
R. Carlin,
C. A. Carrillo Montoya,
F. R. Cavallo,
J. M. Cela Ruiz
, et al. (121 additional authors not shown)
Abstract:
The Compact Muon Solenoid (CMS) experiment prepares its Phase-2 upgrade for the high-luminosity era of the LHC operation (HL-LHC). Due to the increase of occupancy, trigger latency and rates, the full electronics of the CMS Drift Tube (DT) chambers will need to be replaced. In the new design, the time bin for the digitisation of the chamber signals will be of around 1~ns, and the totality of the s…
▽ More
The Compact Muon Solenoid (CMS) experiment prepares its Phase-2 upgrade for the high-luminosity era of the LHC operation (HL-LHC). Due to the increase of occupancy, trigger latency and rates, the full electronics of the CMS Drift Tube (DT) chambers will need to be replaced. In the new design, the time bin for the digitisation of the chamber signals will be of around 1~ns, and the totality of the signals will be forwarded asynchronously to the service cavern at full resolution. The new backend system will be in charge of building the trigger primitives of each chamber. These trigger primitives contain the information at chamber level about the muon candidates position, direction, and collision time, and are used as input in the L1 CMS trigger. The added functionalities will improve the robustness of the system against ageing. An algorithm based on analytical solutions for reconstructing the DT trigger primitives, called Analytical Method, has been implemented both as a software C++ emulator and in firmware. Its performance has been estimated using the software emulator with simulated and real data samples, and through hardware implementation tests. Measured efficiencies are 96 to 98\% for all qualities and time and spatial resolutions are close to the ultimate performance of the DT chambers. A prototype chain of the HL-LHC electronics using the Analytical Method for trigger primitive generation has been installed during Long Shutdown 2 of the LHC and operated in CMS cosmic data taking campaigns in 2020 and 2021. Results from this validation step, the so-called Slice Test, are presented.
△ Less
Submitted 3 February, 2023;
originally announced February 2023.
-
Study of the effects of radiation on the CMS Drift Tubes Muon Detector for the HL-LHC
Authors:
G. Abbiendi,
J. Alcaraz Maestre,
A. Álvarez Fernández,
B. Álvarez González,
N. Amapane,
I. Bachiller,
J. M. Barcala,
L. Barcellan,
C. Battilana,
M. Bellato,
G. Bencze,
M. Benettoni,
N. Beni,
A. Benvenuti,
L. C. Blanco Ramos,
A. Boletti,
A. Bragagnolo,
J. A. Brochero Cifuentes,
V. Cafaro,
A. Calderon,
E. Calvo,
A. Cappati,
R. Carlin,
C. A. Carrillo Montoya,
F. R. Cavallo
, et al. (118 additional authors not shown)
Abstract:
The CMS drift tubes (DT) muon detector, built for withstanding the LHC expected integrated and instantaneous luminosities, will be used also in the High Luminosity LHC (HL-LHC) at a 5 times larger instantaneous luminosity and, consequently, much higher levels of radiation, reaching about 10 times the LHC integrated luminosity. Initial irradiation tests of a spare DT chamber at the CERN gamma irrad…
▽ More
The CMS drift tubes (DT) muon detector, built for withstanding the LHC expected integrated and instantaneous luminosities, will be used also in the High Luminosity LHC (HL-LHC) at a 5 times larger instantaneous luminosity and, consequently, much higher levels of radiation, reaching about 10 times the LHC integrated luminosity. Initial irradiation tests of a spare DT chamber at the CERN gamma irradiation facility (GIF++), at large ($\sim$O(100)) acceleration factor, showed ageing effects resulting in a degradation of the DT cell performance. However, full CMS simulations have shown almost no impact in the muon reconstruction efficiency over the full barrel acceptance and for the full integrated luminosity. A second spare DT chamber was moved inside the GIF++ bunker in October 2017. The chamber was being irradiated at lower acceleration factors, and only 2 out of the 12 layers of the chamber were switched at working voltage when the radioactive source was active, being the other layers in standby. In this way the other non-aged layers are used as reference and as a precise and unbiased telescope of muon tracks for the efficiency computation of the aged layers of the chamber, when set at working voltage for measurements. An integrated dose equivalent to two times the expected integrated luminosity of the HL-LHC run has been absorbed by this second spare DT chamber and the final impact on the muon reconstruction efficiency is under study. Direct inspection of some extracted aged anode wires presented a melted resistive deposition of materials. Investigation on the outgassing of cell materials and of the gas components used at the GIF++ are underway. Strategies to mitigate the ageing effects are also being developed. From the long irradiation measurements of the second spare DT chamber, the effects of radiation in the performance of the DTs expected during the HL-LHC run will be presented.
△ Less
Submitted 12 December, 2019;
originally announced December 2019.
-
Opportunities in Flavour Physics at the HL-LHC and HE-LHC
Authors:
A. Cerri,
V. V. Gligorov,
S. Malvezzi,
J. Martin Camalich,
J. Zupan,
S. Akar,
J. Alimena,
B. C. Allanach,
W. Altmannshofer,
L. Anderlini,
F. Archilli,
P. Azzi,
S. Banerjee,
W. Barter,
A. E. Barton,
M. Bauer,
I. Belyaev,
S. Benson,
M. Bettler,
R. Bhattacharya,
S. Bifani,
A. Birnkraut,
F. Bishara,
T. Blake,
S. Blusk
, et al. (278 additional authors not shown)
Abstract:
Motivated by the success of the flavour physics programme carried out over the last decade at the Large Hadron Collider (LHC), we characterize in detail the physics potential of its High-Luminosity and High-Energy upgrades in this domain of physics. We document the extraordinary breadth of the HL/HE-LHC programme enabled by a putative Upgrade II of the dedicated flavour physics experiment LHCb and…
▽ More
Motivated by the success of the flavour physics programme carried out over the last decade at the Large Hadron Collider (LHC), we characterize in detail the physics potential of its High-Luminosity and High-Energy upgrades in this domain of physics. We document the extraordinary breadth of the HL/HE-LHC programme enabled by a putative Upgrade II of the dedicated flavour physics experiment LHCb and the evolution of the established flavour physics role of the ATLAS and CMS general purpose experiments. We connect the dedicated flavour physics programme to studies of the top quark, Higgs boson, and direct high-$p_T$ searches for new particles and force carriers. We discuss the complementarity of their discovery potential for physics beyond the Standard Model, affirming the necessity to fully exploit the LHC's flavour physics potential throughout its upgrade eras.
△ Less
Submitted 20 February, 2019; v1 submitted 18 December, 2018;
originally announced December 2018.
-
Sponsored Search Auctions with Rich Ads
Authors:
Ruggiero Cavallo,
Prabhakar Krishnamurthy,
Maxim Sviridenko,
Christopher A. Wilkens
Abstract:
The generalized second price (GSP) auction has served as the core selling mechanism for sponsored search ads for over a decade. However, recent trends expanding the set of allowed ad formats---to include a variety of sizes, decorations, and other distinguishing features---have raised critical problems for GSP-based platforms. Alternatives such as the Vickrey-Clarke-Groves (VCG) auction raise diffe…
▽ More
The generalized second price (GSP) auction has served as the core selling mechanism for sponsored search ads for over a decade. However, recent trends expanding the set of allowed ad formats---to include a variety of sizes, decorations, and other distinguishing features---have raised critical problems for GSP-based platforms. Alternatives such as the Vickrey-Clarke-Groves (VCG) auction raise different complications because they fundamentally change the way prices are computed. In this paper we report on our efforts to redesign a search ad selling system from the ground up in this new context, proposing a mechanism that optimizes an entire slate of ads globally and computes prices that achieve properties analogous to those held by GSP in the original, simpler setting of uniform ads. A careful algorithmic coupling of allocation-optimization and pricing-computation allows our auction to operate within the strict timing constraints inherent in real-time ad auctions. We report performance results of the auction in Yahoo's Gemini Search platform.
△ Less
Submitted 20 January, 2017;
originally announced January 2017.
-
GSP - The Cinderella of Mechanism Design
Authors:
Christopher A. Wilkens,
Ruggiero Cavallo,
Rad Niazadeh
Abstract:
Nearly fifteen years ago, Google unveiled the generalized second price (GSP) auction. By all theoretical accounts including their own [Varian 14], this was the wrong auction --- the Vickrey-Clarke-Groves (VCG) auction would have been the proper choice --- yet GSP has succeeded spectacularly.
We give a deep justification for GSP's success: advertisers' preferences map to a model we call value max…
▽ More
Nearly fifteen years ago, Google unveiled the generalized second price (GSP) auction. By all theoretical accounts including their own [Varian 14], this was the wrong auction --- the Vickrey-Clarke-Groves (VCG) auction would have been the proper choice --- yet GSP has succeeded spectacularly.
We give a deep justification for GSP's success: advertisers' preferences map to a model we call value maximization, they do not maximize profit as the standard theory would believe. For value maximizers, GSP is the truthful auction [Aggarwal 09]. Moreover, this implies an axiomatization of GSP --- it is an auction whose prices are truthful for value maximizers --- that can be applied much more broadly than the simple model for which GSP was originally designed. In particular, applying it to arbitrary single-parameter domains recovers the folklore definition of GSP. Through the lens of value maximization, GSP metamorphosizes into a powerful auction, sound in its principles and elegant in its simplicity.
△ Less
Submitted 20 January, 2017;
originally announced January 2017.
-
Mechanism Design for Value Maximizers
Authors:
Christopher A Wilkens,
Ruggiero Cavallo,
Rad Niazadeh,
Samuel Taggart
Abstract:
In many settings, money is a tool of exchange with minimal inherent utility --- agents will spend it in a way that maximizes the value of goods received subject to reasonable constraints, giving only second-order consideration to the trade-off between value and price. While this perspective is commonly captured in consumer choice theory, market equilibrium theory, and other fields, it is markedly…
▽ More
In many settings, money is a tool of exchange with minimal inherent utility --- agents will spend it in a way that maximizes the value of goods received subject to reasonable constraints, giving only second-order consideration to the trade-off between value and price. While this perspective is commonly captured in consumer choice theory, market equilibrium theory, and other fields, it is markedly absent from the mechanism design literature --- agents strategizing in a mechanism with money are almost always assumed to incorporate money as an objective through quasilinear valuations. We study a simple model of value maximizers that captures online advertisers and other agents who may view money solely as a constraint, and study general questions of mechanism design for such agents. We show that the feasible and optimal points faced by a mechanism designer change dramatically from the quasilinear realm and lay a foundation for a broader study of value maximization in mechanism design. Along the way, we offer new insight into the generalized second price (GSP) auction commonly used in Internet advertising. Through the lens of value maximization, GSP metamorphosizes into a truthful auction, sound in its principles and elegant in its simplicity.
△ Less
Submitted 15 July, 2018; v1 submitted 14 July, 2016;
originally announced July 2016.
-
A novel application of Fiber Bragg Grating (FBG) sensors in MPGD
Authors:
D. Abbaneo,
M. Abbas,
M. Abbrescia,
A. A. Abdelalim,
M. Abi Akl,
O. Aboamer,
D. Acosta,
A. Ahmad,
W. Ahmed,
W. Ahmed,
A. Aleksandrov,
R. Aly,
P. Altieri,
C. Asawatangtrakuldee,
P. Aspell,
Y. Assran,
I. Awan,
S. Bally,
Y. Ban,
S. Banerjee,
V. Barashko,
P. Barria,
G. Bencze,
N. Beni,
L. Benussi
, et al. (133 additional authors not shown)
Abstract:
We present a novel application of Fiber Bragg Grating (FBG) sensors in the construction and characterisation of Micro Pattern Gaseous Detector (MPGD), with particular attention to the realisation of the largest triple (Gas electron Multiplier) GEM chambers so far operated, the GE1/1 chambers of the CMS experiment at LHC. The GE1/1 CMS project consists of 144 GEM chambers of about 0.5 m2 active are…
▽ More
We present a novel application of Fiber Bragg Grating (FBG) sensors in the construction and characterisation of Micro Pattern Gaseous Detector (MPGD), with particular attention to the realisation of the largest triple (Gas electron Multiplier) GEM chambers so far operated, the GE1/1 chambers of the CMS experiment at LHC. The GE1/1 CMS project consists of 144 GEM chambers of about 0.5 m2 active area each, employing three GEM foils per chamber, to be installed in the forward region of the CMS endcap during the long shutdown of LHC in 2108-2019. The large active area of each GE1/1 chamber consists of GEM foils that are mechanically stretched in order to secure their flatness and the consequent uniform performance of the GE1/1 chamber across its whole active surface. So far FBGs have been used in high energy physics mainly as high precision positioning and re-positioning sensors and as low cost, easy to mount, low space consuming temperature sensors. FBGs are also commonly used for very precise strain measurements in material studies. In this work we present a novel use of FBGs as flatness and mechanical tensioning sensors applied to the wide GEM foils of the GE1/1 chambers. A network of FBG sensors have been used to determine the optimal mechanical tension applied and to characterise the mechanical tension that should be applied to the foils. We discuss the results of the test done on a full-sized GE1/1 final prototype, the studies done to fully characterise the GEM material, how this information was used to define a standard assembly procedure and possible future developments.
△ Less
Submitted 28 December, 2015;
originally announced December 2015.
-
Fiber Bragg Grating (FBG) sensors as flatness and mechanical stretching sensors
Authors:
D. Abbaneo,
M. Abbas,
M. Abbrescia,
A. A. Abdelalim,
M. Abi Akl,
O. Aboamer,
D. Acosta,
A. Ahmad,
W. Ahmed,
W. Ahmed,
A. Aleksandrov,
R. Aly,
P. Altieri,
C. Asawatangtrakuldee,
P. Aspell,
Y. Assran,
I. Awan,
S. Bally,
Y. Ban,
S. Banerjee,
V. Barashko,
P. Barria,
G. Bencze,
N. Beni,
L. Benussi
, et al. (133 additional authors not shown)
Abstract:
A novel approach which uses Fibre Bragg Grating (FBG) sensors has been utilised to assess and monitor the flatness of Gaseous Electron Multipliers (GEM) foils. The setup layout and preliminary results are presented.
A novel approach which uses Fibre Bragg Grating (FBG) sensors has been utilised to assess and monitor the flatness of Gaseous Electron Multipliers (GEM) foils. The setup layout and preliminary results are presented.
△ Less
Submitted 28 December, 2015;
originally announced December 2015.
-
Performance of a Large-Area GEM Detector Prototype for the Upgrade of the CMS Muon Endcap System
Authors:
D. Abbaneo,
M. Abbas,
M. Abbrescia,
A. A. Abdelalim,
M. Abi Akl,
W. Ahmed,
W. Ahmed,
P. Altieri,
R. Aly,
C. Asawatangtrakuldee,
A. Ashfaq,
P. Aspell,
Y. Assran,
I. Awan,
S. Bally,
Y. Ban,
S. Banerjee,
P. Barria,
L. Benussi,
V. Bhopatkar,
S. Bianco,
J. Bos,
O. Bouhali,
S. Braibant,
S. Buontempo
, et al. (113 additional authors not shown)
Abstract:
Gas Electron Multiplier (GEM) technology is being considered for the forward muon upgrade of the CMS experiment in Phase 2 of the CERN LHC. Its first implementation is planned for the GE1/1 system in the $1.5 < \midη\mid < 2.2$ region of the muon endcap mainly to control muon level-1 trigger rates after the second long LHC shutdown. A GE1/1 triple-GEM detector is read out by 3,072 radial strips wi…
▽ More
Gas Electron Multiplier (GEM) technology is being considered for the forward muon upgrade of the CMS experiment in Phase 2 of the CERN LHC. Its first implementation is planned for the GE1/1 system in the $1.5 < \midη\mid < 2.2$ region of the muon endcap mainly to control muon level-1 trigger rates after the second long LHC shutdown. A GE1/1 triple-GEM detector is read out by 3,072 radial strips with 455 $μ$rad pitch arranged in eight $η$-sectors. We assembled a full-size GE1/1 prototype of 1m length at Florida Tech and tested it in 20-120 GeV hadron beams at Fermilab using Ar/CO$_{2}$ 70:30 and the RD51 scalable readout system. Four small GEM detectors with 2-D readout and an average measured azimuthal resolution of 36 $μ$rad provided precise reference tracks. Construction of this largest GEM detector built to-date is described. Strip cluster parameters, detection efficiency, and spatial resolution are studied with position and high voltage scans. The plateau detection efficiency is [97.1 $\pm$ 0.2 (stat)]\%. The azimuthal resolution is found to be [123.5 $\pm$ 1.6 (stat)] $μ$rad when operating in the center of the efficiency plateau and using full pulse height information. The resolution can be slightly improved by $\sim$ 10 $μ$rad when correcting for the bias due to discrete readout strips. The CMS upgrade design calls for readout electronics with binary hit output. When strip clusters are formed correspondingly without charge-weighting and with fixed hit thresholds, a position resolution of [136.8 $\pm$ 2.5 stat] $μ$rad is measured, consistent with the expected resolution of strip-pitch/$\sqrt{12}$ = 131.3 $μ$rad. Other $η$-sectors of the detector show similar response and performance.
△ Less
Submitted 8 December, 2014; v1 submitted 30 November, 2014;
originally announced December 2014.
-
Observation of the rare $B^0_s\toμ^+μ^-$ decay from the combined analysis of CMS and LHCb data
Authors:
The CMS,
LHCb Collaborations,
:,
V. Khachatryan,
A. M. Sirunyan,
A. Tumasyan,
W. Adam,
T. Bergauer,
M. Dragicevic,
J. Erö,
M. Friedl,
R. Frühwirth,
V. M. Ghete,
C. Hartl,
N. Hörmann,
J. Hrubec,
M. Jeitler,
W. Kiesenhofer,
V. Knünz,
M. Krammer,
I. Krätschmer,
D. Liko,
I. Mikulec,
D. Rabady,
B. Rahbaran
, et al. (2807 additional authors not shown)
Abstract:
A joint measurement is presented of the branching fractions $B^0_s\toμ^+μ^-$ and $B^0\toμ^+μ^-$ in proton-proton collisions at the LHC by the CMS and LHCb experiments. The data samples were collected in 2011 at a centre-of-mass energy of 7 TeV, and in 2012 at 8 TeV. The combined analysis produces the first observation of the $B^0_s\toμ^+μ^-$ decay, with a statistical significance exceeding six sta…
▽ More
A joint measurement is presented of the branching fractions $B^0_s\toμ^+μ^-$ and $B^0\toμ^+μ^-$ in proton-proton collisions at the LHC by the CMS and LHCb experiments. The data samples were collected in 2011 at a centre-of-mass energy of 7 TeV, and in 2012 at 8 TeV. The combined analysis produces the first observation of the $B^0_s\toμ^+μ^-$ decay, with a statistical significance exceeding six standard deviations, and the best measurement of its branching fraction so far. Furthermore, evidence for the $B^0\toμ^+μ^-$ decay is obtained with a statistical significance of three standard deviations. The branching fraction measurements are statistically compatible with SM predictions and impose stringent constraints on several theories beyond the SM.
△ Less
Submitted 17 August, 2015; v1 submitted 17 November, 2014;
originally announced November 2014.
-
GSP with General Independent Click-Through-Rates
Authors:
Ruggiero Cavallo,
Christopher A. Wilkens
Abstract:
The popular generalized second price (GSP) auction for sponsored search is built upon a separable model of click-through-rates that decomposes the likelihood of a click into the product of a "slot effect" and an "advertiser effect" --- if the first slot is twice as good as the second for some bidder, then it is twice as good for everyone. Though appealing in its simplicity, this model is quite sus…
▽ More
The popular generalized second price (GSP) auction for sponsored search is built upon a separable model of click-through-rates that decomposes the likelihood of a click into the product of a "slot effect" and an "advertiser effect" --- if the first slot is twice as good as the second for some bidder, then it is twice as good for everyone. Though appealing in its simplicity, this model is quite suspect in practice. A wide variety of factors including externalities and budgets have been studied that can and do cause it to be violated. In this paper we adopt a view of GSP as an iterated second price auction (see, e.g., Milgrom 2010) and study how the most basic violation of separability --- position dependent, arbitrary public click-through-rates that do not decompose --- affects results from the foundational analysis of GSP (Varian 2007, Edelman et al. 2007). For the two-slot setting we prove that for arbitrary click-through-rates, for arbitrary bidder values, an efficient pure-strategy equilibrium always exists; however, without separability there always exist values such that the VCG outcome and payments cannot be realized by any bids, in equilibrium or otherwise. The separability assumption is therefore necessary in the two-slot case to match the payments of VCG but not for efficiency. We moreover show that without separability, generic existence of efficient equilibria is sensitive to the choice of tie-breaking rule, and when there are more than two slots, no (bid-independent) tie-breaking rule yields the positive result. In light of this we suggest alternative mechanisms that trade the simplicity of GSP for better equilibrium properties when there are three or more slots.
△ Less
Submitted 12 October, 2014;
originally announced October 2014.
-
Optimal Coordinated Planning Amongst Self-Interested Agents with Private State
Authors:
Ruggiero Cavallo,
David C. Parkes,
Satinder Singh
Abstract:
Consider a multi-agent system in a dynamic and uncertain environment. Each agent's local decision problem is modeled as a Markov decision process (MDP) and agents must coordinate on a joint action in each period, which provides a reward to each agent and causes local state transitions. A social planner knows the model of every agent's MDP and wants to implement the optimal joint policy, but agents…
▽ More
Consider a multi-agent system in a dynamic and uncertain environment. Each agent's local decision problem is modeled as a Markov decision process (MDP) and agents must coordinate on a joint action in each period, which provides a reward to each agent and causes local state transitions. A social planner knows the model of every agent's MDP and wants to implement the optimal joint policy, but agents are self-interested and have private local state. We provide an incentive-compatible mechanism for eliciting state information that achieves the optimal joint plan in a Markov perfect equilibrium of the induced stochastic game. In the special case in which local problems are Markov chains and agents compete to take a single action in each period, we leverage Gittins allocation indices to provide an efficient factored algorithm and distribute computation of the optimal policy among the agents. Distributed, optimal coordinated learning in a multi-agent variant of the multi-armed bandit problem is obtained as a special case.
△ Less
Submitted 27 June, 2012;
originally announced June 2012.
-
Hydra Observations of Aluminum Abundances in the Red Giants of the Globular Clusters M80 and NGC 6752
Authors:
Robert M. Cavallo,
Nicholas B. Suntzeff,
Catherine A. Pilachowski
Abstract:
Aluminum and other metal abundances were determined in 21 red giants in the globular clusters NGC 6752 and M80 as part of a larger study to determine whether the aluminum distribution on the red giant branch is related to the second parameter effect that causes clusters of similar metallicity to display different horizontal branch morphologies. The observations were obtained of the Al I lines ne…
▽ More
Aluminum and other metal abundances were determined in 21 red giants in the globular clusters NGC 6752 and M80 as part of a larger study to determine whether the aluminum distribution on the red giant branch is related to the second parameter effect that causes clusters of similar metallicity to display different horizontal branch morphologies. The observations were obtained of the Al I lines near 6700 Angstroms with the CTIO Blanco 4-m telescope and Hydra multi-object spectrograph. The spectra have a resolving power of 18000 or 9400, with typical S/N ratios of 100-200. Mean [Fe/H] values obtained from the spectra are -1.58 for NGC 6752 and -1.73 for M80; this represents the first spectroscopic iron abundance determination for M80. Both NGC 6752 and M80 display a spread in aluminum abundance, with mean [Al/Fe] ratios of +0.51 and +0.37, respectively. No trend in the variation of the mean Al abundance with position on the giant branch is discernible in either cluster with our small sample.
△ Less
Submitted 10 March, 2004;
originally announced March 2004.
-
Djehuty, a Code for Modeling Stars in Three Dimensions
Authors:
G. Bazan,
D. S. P. Dearborn,
D. D. Dossa,
P. P. Eggleton,
A. Taylor,
J. I. Castor,
S. Murray,
K. H. Cook,
P. G. Eltgroth,
R. M. Cavallo,
S. Turcotte,
S. C. Keller,
B. S. Pudliner
Abstract:
Current practice in stellar evolution is to employ one-dimensional calculations that quantitatively apply only to a minority of the observed stars (single non-rotating stars, or well detached binaries). Even in these systems, astrophysicists are dependent on approximations to handle complex three-dimensional processes like convection. Understanding the structure of binary stars, like those that…
▽ More
Current practice in stellar evolution is to employ one-dimensional calculations that quantitatively apply only to a minority of the observed stars (single non-rotating stars, or well detached binaries). Even in these systems, astrophysicists are dependent on approximations to handle complex three-dimensional processes like convection. Understanding the structure of binary stars, like those that lead to the Type Ia supernovae used to measure the expansion of the universe, are grossly non-spherical and await a 3D treatment.
To approach very large problems like multi-dimensional modeling of stars, the Lawrence Livermore National Laboratory has invested in massively parallel computers and invested even more in developing the algorithms to utilize them on complex physics problems. We have leveraged skills from across the lab to develop a 3D stellar evolution code, Djehuty (after the Egyptian god for writing and calculation) that operates efficiently on platforms with thousands of nodes, with the best available physical data (opacities, EOS, etc.). Djehuty has incorporated all basic physics for modeling stars including an accurate equation of state, radiation transport by diffusion, thermonuclear reaction rates, and hydrodynamics, and we have begun testing it in a number of applications.
△ Less
Submitted 6 June, 2003;
originally announced June 2003.
-
Preliminary Abundance Analysis of Galactic Bulge Main Sequence, Subgiant, and Giant Branch Stars Observed During Microlensing with Keck/HIRES
Authors:
R. M. Cavallo,
K. H. Cook,
D. Minniti,
T. Vandehei
Abstract:
We present an abundance analysis of six main sequence turnoff, subgiant, and giant branch stars toward the Galactic bulge that were observed with Keck/HIRES during microlensing events. This is an early look at the first detailed chemical analysis of main sequence stars in the Galactic bulge. Lensing events allow the effective aperture of Keck to be increased beyond its current dimensions; althou…
▽ More
We present an abundance analysis of six main sequence turnoff, subgiant, and giant branch stars toward the Galactic bulge that were observed with Keck/HIRES during microlensing events. This is an early look at the first detailed chemical analysis of main sequence stars in the Galactic bulge. Lensing events allow the effective aperture of Keck to be increased beyond its current dimensions; although, some events still stretched its spectroscopic capabilities. Future large telescopes with high resolution and high throughput spectrometers will allow the study of abundances in distant stellar populations and in less evolved stars with greater ease.
△ Less
Submitted 10 September, 2002;
originally announced September 2002.
-
Djehuty: A Code for Modeling Whole Stars in Three Dimensions
Authors:
S. Turcotte,
G. Bazan,
J. Castor,
R. Cavallo,
H. Cohl,
K. Cook,
D. S. P. Dearborn,
D. Dossa,
R. Eastman,
P. P. Eggleton,
P. Eltgroth,
S. Keller,
S. Murray,
A. Taylor
Abstract:
The DJEHUTY project is an intensive effort at the Lawrence Livermore National Laboratory (LLNL) to produce a general purpose 3-D stellar structure and evolution code to study dynamic processes in whole stars.
The DJEHUTY project is an intensive effort at the Lawrence Livermore National Laboratory (LLNL) to produce a general purpose 3-D stellar structure and evolution code to study dynamic processes in whole stars.
△ Less
Submitted 17 December, 2001;
originally announced December 2001.
-
Aluminum Abundances, Deep Mixing and the Blue-Tail Second-Parameter Effect in the Globular Clusters M 3 and M 13
Authors:
Robert M. Cavallo,
Neil M. Nagar
Abstract:
We explore the relatiohsip between deep mixing on the red-giant branch and the second parameter that gives rise to the extended blue tail seen on the horizontal branch of the globular cluster M 13. We use the [Al/Fe] values of 96 RGB stars and the [Na/Fe] values of 119 RGB stars in M 13 to follow the evolution of mixing in this cluster. The data are compared to an "instantaneous" mixing algorith…
▽ More
We explore the relatiohsip between deep mixing on the red-giant branch and the second parameter that gives rise to the extended blue tail seen on the horizontal branch of the globular cluster M 13. We use the [Al/Fe] values of 96 RGB stars and the [Na/Fe] values of 119 RGB stars in M 13 to follow the evolution of mixing in this cluster. The data are compared to an "instantaneous" mixing algorithm to predict the effects of deep mixing on the HB morphology. In addition, we present new data for six giants in the cluster M 3 and three in M 13. Our final results are consistent with deep mixing as a blue-tail second parameter. We also examine the question of overproducing sodium during deep mixing and suggest ways around this problem and observational tests that center around the s-process elements Sr, Y and Zr.
△ Less
Submitted 19 May, 2000; v1 submitted 28 February, 2000;
originally announced February 2000.
-
Aluminum Abundances on the Red Giant Branch: Testing Helium Mixing as a Second Parameter
Authors:
R. M. Cavallo
Abstract:
We present new data and discuss the relationship between the Al abundances on the red giant branches (RGBs) and the horizontal-branch (HB) morphologies of the second-parameter pair of globular clusters M3 and M13. Since Al is produced during RGB evolution inside the H-burning shell where He is synthesized, its overabundance in stellar atmospheres can indicate He mixing, which has been shown to b…
▽ More
We present new data and discuss the relationship between the Al abundances on the red giant branches (RGBs) and the horizontal-branch (HB) morphologies of the second-parameter pair of globular clusters M3 and M13. Since Al is produced during RGB evolution inside the H-burning shell where He is synthesized, its overabundance in stellar atmospheres can indicate He mixing, which has been shown to be a viable second parameter in explaining HB morpohogies.
△ Less
Submitted 19 November, 1998;
originally announced November 1998.
-
Proton-Capture Nucleosynthesis in Globular Cluster Red Giant Stars
Authors:
Robert M. Cavallo,
Allen V. Sweigart,
Roger A. Bell
Abstract:
We follow the static abundance profiles of the C, N, O, Ne, Na, Mg, and Al isotopes around the hydrogen-burning shell (H shell) of globular cluster red-giant-branch (RGB) stellar models in order to study the observed abundance anomolies associated with these elements. We do this by combining four "realistic" stellar evolutionary sequences of different metallicities with a detailed nuclear reacti…
▽ More
We follow the static abundance profiles of the C, N, O, Ne, Na, Mg, and Al isotopes around the hydrogen-burning shell (H shell) of globular cluster red-giant-branch (RGB) stellar models in order to study the observed abundance anomolies associated with these elements. We do this by combining four "realistic" stellar evolutionary sequences of different metallicities with a detailed nuclear reaction network. This approach allows for the variation in the temperature and density around the H shell as well as structural changes in the H shell caused by advancing evolution and variations in metallicity. In addition, our reaction network allows us to explore the effects of the uncertainties in the reaction rates on the abundance profiles.
Our results are qualitatively consistent with the observed C vs. N, and O vs. N, Na, and Al anticorrelations as well as with the observed luminosity- and metallicity-dependent variations in the abundances and isotopic ratios. We find that the source of the large Al enhancements in some clusters is 24Mg, but contrary to the results of Shetrone (1996b;1997) we are unable to deplete the 24Mg abundance due to leakage from the NeNa cycle via the 23Na(p,gamma)24Mg reaction. We discuss possible remedies to this discrepancy.
△ Less
Submitted 11 August, 1997;
originally announced August 1997.
-
The Production of Sodium and Aluminum in Globular Cluster Red Giant Stars
Authors:
Robert M. Cavallo,
Allen V. Sweigart,
Roger A. Bell
Abstract:
We study the production of Na and Al around the hydrogen shell of two red-giant sequences of different metallicity in order to explain the abundance variations seen in globular cluster stars in a mixing scenario. Using detailed stellar models together with an extensive nuclear reaction network, we have calculated the distribution of the various isotopic abundances around the hydrogen shell at nu…
▽ More
We study the production of Na and Al around the hydrogen shell of two red-giant sequences of different metallicity in order to explain the abundance variations seen in globular cluster stars in a mixing scenario. Using detailed stellar models together with an extensive nuclear reaction network, we have calculated the distribution of the various isotopic abundances around the hydrogen shell at numerous points along the red-giant branch. These calculations allow for the variation in both temperature and density in the shell region as well as the timescale of the nuclear processing, as governed by the outward movement of the hydrogen shell. The reaction network uses updated rates over those of Caughlin \& Fowler (1988). We find evidence for the production of Na and Al occurring in the NeNa and MgAl cycles. In particular, Na is significantly enhanced throughout the region above the hydrogen shell. The use of the newer reaction rates causes a substantial increase in the production of $^{27}$Al above the hydrogen shell through heavy leakage from the NeNa cycle and should have an important effect on the predicted surface abundances. We also find that the nuclear processing is considerably more extensive at lower metallicities.
△ Less
Submitted 3 April, 1996;
originally announced April 1996.
